T43p no longer recognizes 2877 docking station

My ThinkPad T43p no longer recognizes when it's installed in my ThinkPad Dock II (2877) docking station.  Thinkpad has latest possible BIOS and Lenovo power management updates.  It runs Windows XP SP3 at latest possible updates.  It normally runs in the docking station in my office, but I removed it the other day to use it in the living room.  When I re-installed it, it booted as if on battery power and remained running solely on battery power.
I have always cold-docked and undocked this machine, i.e., the PC is shut down before undocking and before re-docking.
On the docking station, none of the attached devices are recognized ( e.g., mouse, hard disk).  Strangely, the docking station power button does boot the PC and power it down, but none of the other docking station functions work including the eject button.
On the laptop Windows XP software, there is no Eject PC in the START/shutdown program list.
I've cleaned the umbilical connector strip on the base of the T43p and on the docking station with compressed air.
The T43p works fine undocked using the brick power supply, fully charging the battery.  The ports on the laptop all work fine.
I'd appreciate suggestions short of ditching the docking station and the laptop.

Which docking station - make and model?

Similar Messages

  • Undocking a T42P from a 2877 docking station with an ultrabay 2000 HDD???

    I have just added a disk drive in the ultrabay 2000 slot of my 2877 docking station that I use to hold my backups.  I can no longer use the "Undock" function because the device is in use by an active program - I assume the operating system or Windows Explorer.  My PC is a ThinkPad T42p running XP at the SP2 level.  Is there any way short of shutting down the PC to flush all of the cache to the 2nd HDD and be able to safely undock the laptop from the docking station?
    Thanks,
    scott

    Thanks for the reply, Huffer. I was plugging it into one of the 3.0 ports. I just tried the 2.0 port. Disk Management successfully loaded, and presented me with an "Initialize Disk" window (I hit "Cancel"). It showed that HDD as "Not initialized" and having no partitions (all space unallocated). No new drives appeared in Computer.
    The drive behaved fine when used with my old laptop (the issue with that laptop is a power supply issue, not a drive issue). I don't have another working computer to try it in, nor do I have another drive to try in the docking station.
    I assume that I should not initialize it, as that may make my data more difficult to recover, correct? Is problem likely my laptop, the docking station, the drive, or an incompatibility issue? What utility might I be able to use to see this partition and copy my data over?

  • Ipod will no longer charge on docking station or car dock

    My ipod will no longer charge while it is playing on my docking station or on the car dock. The only way I can charge now is with the genuine charger which means I can only listen for a couple of hours and then have to charge up again. Any ideas?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable                     
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • IPod Touch on iOS 6.0.1 no longer works with docking station

    Hi there,
    I have an iPod Touch 4G recently upgraded to iOS 6.0.1. and a Philips AJ7041D/12 docking station for that.
    After the upgrade to iOS 6.0.1. the IPod says the docking is not a supported device and they no longer work together.
    Does anyone know how I can get things working again?
    Your help will be much appreciated.
    Regards,
    Dick

    Sometimes this works. However, sometime an iOS upgrade breaks compatibility and yoo will have to wait for an IOS update or an update to your dock's firmware.
    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:       
    iOS: How to back up           
    - Restore to factory settings/new iOS device.

  • Since IOS7 update my ipad no longer works on docking station

    Hi Peeps
    since ios7 update on the ipad, it no longer plays music through the speakers, i have searched online and done the soft reset etc but to no avail, its still charges but there is no sound out of the speakers, plays through the Ipad.  I intially thought the docking station was broken put plays my ipod 3rd gen which is currently on 6.1.3?
    Any help would be greatly appreciated

    Same as mine, My JBL onbeat mini worked fine with Ipad last night and now it says " may not be supported"
    Sick to death with Apple and what they have become, will not be tied down to them any longer considering the alternatives on the market today.

  • Compatible with Type 2877 docking station?

    Greetings!
    I'm trying to figure out whether my pre-existing docking station (Type 2877, with American power cord) is compatible with the new members of the X-series of Thinkpads? (I'm probably leaning more towards a 13.3" laptop, so it's also relevant whether the SL300 is compatible)
    Thank you in advance!

    The last generation of ThinkPads that can use this dock are T4x, R5x and X3x units. All of them utilize Pentium M CPUs.
    Please note that not all R5x machines support docking.
    Hope this helps.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • No longer working with docking station

    Second time this has happened. I had my iPhone 3GS working fine through a docking station for music -- now all of a sudden it only plays through the iphone speaker. Previous iPhone did the same thing with another docking station - worked then stopped working one day. Any fix suggested?

    Which docking station - make and model?

  • T43 stuck in docking station

    My T43 is stuck in the docking station (Type 2877).  The button to release it does not pop up properly, and the locking lugs won't let go.  Any help?
    Solved!
    Go to Solution.

    Quoting from P/N 67P5254 (ThinkPad Dock II User's Guide):
    Emergency Eject:
    When AC power is not supplied, the Eject button does not pop up automatically.  To make it pop up, do the following:
    1. Press the Eject button.
    2. Insert a small flat-head screwdriver into the emergency eject hole, which is to the left of the security keyhole.
    3. Using the screwdriver, move the small silver plate in the hole to the left.
    (This worked for me with my T43p stuck in the 2877 docking station.)

  • Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

    Hi.  In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds.  Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended.  I folllowed all the directions from the apple support pages, and finally got it to work.  I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension.  Then a week or so ago I noticed that my laptop would no longer connect to my base station.  I did not have time to look into it until this week.  Airport utility, either on my Mac or iphone no longer recognizes my base station.  My mac is running OS X 10.10.1  and my iPhone is running iOS 8.1.2  I have tried both hard, soft and factory resets of my base station to no avail.  The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before.  I can't actually connect to it, but it does try.  Then after approximately 5 minutes, it disappears from my list.
    Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c?  airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software.  I am attaching an image of that.
    Thank you,
    John
      Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

    I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
    Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
    Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
    Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
    Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
    Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

  • I upgraded my ipad 2 to ios 5.1 and it no longer recognizes or plays through my speaker dock.  Help!

    I just upgraded my ipad 2 to ios 5.1 and it no longer recognizes or plays through my speaker dock. 
    I have tried:
    - multiple soft and hard resets (including various sequences published on this site... no luck)
    - reseting the ipad settings (location, wifi, etc)
    - 2 complete system wipe-out and restore cycles
    - changing every setting I can think of
    I still have normal sound from the device when it is not docked.  When docked, my device still charges and it clearly recognizes it is plugged into something (as the volume slider will no longer function with the side keys while docked) but it won't play and eventually it gives me a message that says "accessory not supported by ipad."  This speaker dock is designed specifically for ipad (brookstone idesign boombox) and worked flawlessly until 2 days ago when I installed the ios 5.1 update.   
    Please help!

    Not quite the same problem but my speaker dock no longer charges iPad1 and iPhone4 since upgrading to iOS5.1 but was playing and charging only the day before, extremely annoying as I have only had the dock about 3 weeks now.
    I haven't tried my iPad3 yet, but will assume that it will do the same

  • APPLE DOCKING STATION NO LONGER WORKS WITH TOUCH 3G and 4G after ios 4.2.1

    APPLE DOCKING STATION NO LONGER WORKS WITH TOUCH 3G and 4G after ios 4.2.1 update.
    I have both of these touches. I updated both 3g and 4g to ios 4.2.1 and poof...no docking station support other than charging, no audio and no remote function. My av/cable works with the tv, and the headphone jack still outputs audio, just no auido through the Apple dock and hte remote is dead. I purchased the dock from the apple store last year and it was working with both ipod 3g and 4g grrrrr...
    Is Apple now in the bug trade business?, trade one for another....
    Anyone else have this problem?

    My iPod Touch 3G running 4.2.1 works fine with the Apple docking station.
    Perhaps you have a loose cable somewhere and/or a dead battery in your controller?

  • My sons iPod touch stopped working, it won't charge in a docking station and the computer/itunes won't recognize it when connected.  We have tried holding the power and home button at the same time for several seconds, and the screen still stays black

    My sons iPod touch stopped working, it won't charge in a docking station and the computer/itunes won't recognize it when connected.  We have tried holding the power and home button at the same time for several seconds, and the screen still stays black.  Thanks!

    Hello skdog I possibly think your ipod touch is black because it has not charged. If your dock is broken it might just mean the dock will be broken and so might be the USB port. You should see an Apple shop nearby and hand it over and see what they can do. I hope this information works!

  • After updating to iOS7, my JBL docking station no longer plays music.

    IPhone 5, iOS7 JBL docking station no longer plays music, the phone does charge but no music will play through station.  Using Lightning to 30 pin adaptor. Any Ideas on troubleshooting or do I just need to roll back to 6 until this gets fixed?

    No roll back
    Tried any troubleshooting
    Reset
    Restore with a backup and if required as new

  • HT1339 my ipod nano 7th generation....works fine as long as it's on the docking station. when off the station, the display goes dark after a few seconds. it's fully charged. please help. this is the heartbeat of my business. thanks

    my ipod nano 7th generation....works fine as long as it's on the docking station. when off the station, the display goes dark after a few seconds. it's fully charged. please help. this is the heartbeat of my business. thanks

    In the worst case, it's still under warranty (all 7th gen nanos are still under one year from purchase).
    So, you disconnect it from power, and it almost immediately goes dead?  You can try a Restore... but it doesn't sound like the type of problem a Restore will fix.
    You should probably have it looked by Apple Tech Support.  If there's an Apple Store nearby, you can take it to the store's Genius Bar.  To avoid waiting, you can make a reservation at the store's web page
    http://www.apple.com/retail/

  • No longer can play though docking stations.

    I have two compatible docking stations, a Bose portable and a shoe to connect to our built in home system. Always worked fine on both until today. This device still running on os version 4.3.3, so recent upgrade of os is not the culprit. Suspect something wrong in the connection. In both cases the IPod touch recognizes it's connected to a docking station and starts to charge, but it continues to play music through it's little inboard speaker instead of connecting to big speakers through the docking station.
    Any help?
    Thanks.

    - Inspect the dock connector for bend or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Does the iPod play OK throiugh the headphone jack? If yes then sometimes this works
    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If it does not play through the headphone jack
    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
    Try the following to rule out a software problem
    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iPod.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
    Apple Retail Store - Genius Bar
    Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
    Apple - iPod Repair price
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the jack yourself
    iPod Touch Repair – iFixit

Maybe you are looking for

  • Special stock indicator for components

    Hi, For a configarable material a sales order is created which in turn creates a production order. Now in this production order for some materials i find that in component overview of production order indicator SP is 1 (Individual customer stock). Th

  • Is Lightroom intentionally made difficult for non-English users?

    Could it be that Lightroom is intentionally made difficult for the non-English user? I came to this forum today hoping to find an answer and all I see is problems when I try searching the forum, and complicated instructions on how to, supposdely, sol

  • Status Record Error 51 in IDOC , Message no. B1252

    Hi,     I have the follwoing error Function module not allowed: YPS_IDOC_INPUT_PROJECT Message no. B1252 Diagnosis The function module YPS_IDOC_INPUT_PROJECT and the application object type BUS2054 which were determined are not valid for this IDoc. P

  • Store an XMPPConnection (Smack chat library obj) in a session

    Hello all, I am attempting to develop a web based chat client (I have already seen jwchat and some others) using the open source Smack libraries. I want a way to maintain the XMPPConnection object in the session. Below is some code I am using: //here

  • Unable to disable the "Enable Administration Port" (Weblogic 12.1.1.0)

    Hi, I have a Weblogic server installation from which the field "Enable Administration Port" has been checked (Probably the Administration Port is now 9002, but I cannot check it). As a consequence I am unable to access the Console. When I try to acce