T440p (Windows 7) - Realtek wireless not working, repeatedly being disabled in Device Manager

Hi all,
I have a brand new T440p (type 20AN I believe) with a clean Win7 Pro SP1 install and all Windows Updates. Very soon after starting to use it, the wireless started acting strange, it would disable itself out of nowhere. In Device Manager, it shows with a yellow exclamation (it is called 2x2 11b/g/n Wireless LAN M.2 Adapter), and if I go into details, under General -> Device Status, it says "Windows has stopped this device because it has reported problems. (Code 43)"
If I right click and Disable, then re-enable, it pauses for a second, looks ok, then the Yellow ! comes back. In the Windows Event Log, it repeatedly logs Warning, Source=WLAN-AutoConfig, Event ID = 10002. The error is WLAN Extensibility Module has stopped. Module Path: C:\Windows\system32\Rtlihvs.dll
I've tried looking for a different driver, and I've uninstalled the driver from the PC completely and reinstalled, but same thing happens. The driver I have is version 2010.6.807.2013, Driver Provider is Realtek Semiconductor Corp, dated 8/7/2013. This is the same driver I found right on the Lenovo support site.
I've also tried switching the adapters on and off using F8.
I have run all necessary/relevant Lenovo updates also, from ThinkVantage Tools -> Update and Drivers. Can't recall if there was a BIOS update. I also ran sfc /scannow and it did not find any issues.
I do not have Access Connections installed. I had tried installing it to see if it made a difference, but it did not.
I found this article which seemed pretty relevant, but no help there, issues are not applicable.
Any help or advice is appreciated. Thanks in advance

Furmann,
what is the type of wireless card in your laptop? I opened a ticket with Lenovo and asked for a brand new wifi card, and they ended up sending an Intel Centrino card (forget the number, maybe 6235?) and I swapped that out, and it has been working fine ever since.

Similar Messages

HP Envy dv4 Windows 8- HP TrueVision HD Webcam not working or showing up in device manager

The subject is fairly self explanatory, I am using a HP Envy dv4 on Windows 8 and trying to use the 'HP TrueVision HD ' Webcam which is not working. When I went to find it in the device manager it was not present. I have restarted my computer already.
Thanks

Hey @kleinhansjy ,
Welcome to the HP Forums!
I understand the webcam in your ENVY dv4 notebook is not working.
Can you tell me if the webcam worked previously, has never worked, or stopped working after updating to Windows 8 (if the notebook did not come with Windows 8 pre-installed).
It would also help to know which exact notebook model you have. For information on finding your product and model numbers click here: How Do I Find My Model Number or Product Number?
While I await your answers please try following these troubleshooting guides:
Webcam Troubleshooting (Windows 8).
Fixing Webcam After Changing the Operating System.
Some of the steps may not apply if the webcam is not detected in Device Manager. You may need to show the hidden devices by clicking View > Show hidden devices. You might find the webcam is listed as an Unknown device in the Other devices category.
I look forward to your reply!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

S10-3t bluetooth and wireless not working with windows 8

S10-3t bluetooth and wireless not working with windows 8. I tried everything but doesn't work at all. I don't know where to find the new drivers that are comatible with windows 8 ???!!! please help me to solve this problem because i tried everything....

Do you still have your windows7 install files ?
( installation image is usually in LENOVO_PART OKRBackup/Factory ) ? I lost them :\
if yes I fear you have to enable it in win7 and then use it in win8
http://rzr.online.fr/q/lenovo# g470 s103t (Please Contact me if your s10-3T is booting win7 or support bluetooth, 3g)
Lenovo S10-3t | Model Name : 0651 | Mfg Date: 2010/06/08
Lenovo G470 | Model Name : 20078 | M fg Date: 11/03/23 | BIOS: 40CN23WW(V2.09) 06/20/2011 | CPU: i5-2410M | Linux version 3.3.4lenovog470+ (root@lap) (gcc version 4.6.3 (Debian 4.6.3-4) ) #8 SMP Tue May 1 10:23:48 CEST 2012
OS:GNU/Linux/Debian

Bluetooth Driver In Windows 8.1 is Not Working after upgrading please help (pavilion g6 2008Tx)

Bluetooth Driver In Windows 8.1 is Not Working after upgrading please help (pavilion g6 2008Tx)
what cAN i do to make it work?please help

Hi:
If your model uses a Ralink wireless card, see if installing this bluetooth driver works.
http://h20565.www2.hp.com/hpsc/swd/public/detail?swItemId=ob_135494_1

Audigy Platinum Ex Windows 7 SPDIF IN not working

Audigy Platinum Ex Windows 7 SPDIF IN not working? I have an old Audigy Platinum Ex that has served me well, until now when I have a new Windows 7 x64 PC (RTM). SPDIF IN no longer works, though everything else does (including SPDIF OUT). I've tried the current and beta drivers for the card, and no difference.
In Windows Vista x64 I could use ASIO drivers with my M-Audio ProFire 60 while using the Audigy for PC audio. Most often this was for skype, which I would set to use SPDIF IN/OUT which I then connected to the ProFires SPDIF OUT/IN. Using the ProFire mixing tool, I could control which mics and levels went to the Audigy while not interfereing with the ASIO drivers recording the mics. The ProFire also recorded the SPDIF OUT from the Audigy to caputre the person on Skype to their own audio track. This is a podcast producer's heaven, and I miss it!
If it's a known issue (SPDIF IN / Win 7), I've had this card through 4 PC upgrades and it's served me well enough I don't mind buying new. The Creative Sound Blaster X-fi Elite Pro looks to be the current version of my Ex - are there any Windows 7 issues currently that would stop me from using it in the role above? I will miss the FireWire port, a shame they dropped that.

Well basically it is possible, and I've found this out. Apparently Dell released a driver or something that allows it to work, but then only if you install a 3rd party modified xp version of the creative suite. I don't remember where I found it, but it was through google... Using some term including x-fi, dts, and vista.... Can't seem to find it now. Anyway, it had a download for the whole creative suite that was modified from the xp version for Vista, however it was buggy as hell, caused driver issues and blue screens, and ended up causing me to have to reinstall Vista altogether again. In other words, it's possible, but I don't recommend it until it's officially supported... Don't know when this will be yet... *crosses fingers*
Luckily I've got a dual OS system with XP too, and I switch to that when I want to use my Xbox 360... However due to Microsoft also being terrible in that department... I now get entertainment off of its 3 red lights... (For those of you who don't know, 3 red lights = hardware error. Sending into microsoft for repair typically is a 2 month process... I'm still waiting on my prepaid shipping box to arri've and it's been 4 days... Will be a similar wait to get it to them, 4-6 weeks for them to actually repair, and another week or so to get it all shipped back). Although even when the console worked, my dsl modem sometimes cut out when playing on Xbox li've and dropped signals, reported errors, etc.
What is with the companies producing technology nowadays? I just want to play Gears in 5. on Xbox li've... *cries*Message Edited by Supercoolyo on 07-22-20070:54 AM

Windows 8,1 bluetooth not working for HP pavillion 15

Hi.....Recently upgraded to windows 8.1 and since then no bluetooth being detected in device manager. please help.
This question was solved.
View Solution.

HI @Nachiket85
Welcome to the HP Forums!
It is a superb place to find answers and ideas!
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
How Do I Find My Model Number or Product Number?
I understand that after updating to Windows 8.1 your bluetooth is not detected. If you go to Device manager and scan for hardware changes does it find it?
To assist you more effectively I will need to know your exact model of HP notebook.
What was the original OS on the notebook?
Was the bluetooth previously working?
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Bluetooth Driver In Windows 8.1 is Not Working [Model :- F0D96EA#ABV]

Bluetooth Driver In Windows 8.1 is Not Working [Model :- F0D96EA#ABV]
When I connect the phone he load and then says no connect

Hi,
Please try the following driver for "MediaTek (Ralink) Bluetooth":
http://ftp.hp.com/pub/softpaq/sp65501-66000/sp65804.exe
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Synaptics touchpad on HP Mini 110 Windows 7 32 Bit - not working for one user - working for another

Hi,
I recently have an issue with Synaptics touchpad on HP Mini 110 Windows 7 32 Bit - NOT working for one user - working for another.
Windows 7 updates recently installed ???
By checking the device properties on the user that works - "Synaptics PS/2 Port Touchpad 13/10/2011 Version 15.3.29.0"
When the other user logs on, the touchpad works for a few seconds, then a displays a black square with a red diagonal line through it, then the touchpad won't respond. Trying to use the keypad to navigate to system diagnosics or anything to find further info is useless....

Hey eagle_no11,
Thank you for joining the HP Support Community!
I will do my best in assisting to hopefully get the TouchPad to work on the second user profile.
What I would like to start off with, is to restore the original Synaptics drivers onto the profile that is not working correctly. I have included the document Using Recovery Manager to Restore Software and Drivers (Windows 7).
Once you have installed the original drivers, you will need to complete all updates from both HP, as well as Windows. For these updates, if you open the HP Support Assistant, and select Maintain, you should see an option for updating.
Please let me know how these steps do work out for you.
Have a great day!
I worked on behalf of HP

Windows 2008 R2 does not work on Sunfire X4170

Hi, I recently bought a used X4170 server and have a weird problem. Windows 2008 R2 does not work, but 2012 does. I tried RTM version and a version with SP1. The problem is this:
After installing, I set the password and windows just displays a blank desktop, sometimes it boots but freezes soon after - the mouse cursor moved but nothing else works.
Booting in Safe Mode works and Windows do not freeze. The Event Log contains lots and lots (about 20 per second) of these entries:
Log Name:
System
Source:
Microsoft-Windows-WHEA-Logger
Date:
6/21/2014 12:24:59 AM
Event ID:
17
Task Category: None
Level:
Warning
Keywords:
User:
LOCAL SERVICE
Computer:
WIN-SOGS2TPM334
Description:
A corrected hardware error has occurred.
Component: PCI Express Root Port
Error Source: Advanced Error Reporting (PCI Express)
Bus:Device:Function: 0x0:0x0:0x0
Vendor ID:Device ID: 0x8086:0x3406
Class Code: 0x30000
I have tried updating the driver for this device (downloaded from Intel), no difference. Is there a way to make Windows 2008 R2 work on this server?

Hello
Thank you for the update.
Please refer the below Knowledge document related to this issue:
Windows BSOD WHEA_UNCORRECTABLE_ERROR(124) & correctable WHEA events when disabling network ports on X4170M2/X4270M2 (Doc ID 1576683.1)
However above document talks about X4170M2, I would suggest you to follow and if issue persist, please open Service Request with Oracle to diagnose further.
Best Regards
Bhavyesh

I have triple pointers on PSE7 & Windows 8. Windows 7 solution does not work

I have triple pointers on PSE7 & Windows 8. Windows 7 solution does not work-can't find how to change DPI

Right click on your Desktop and select Screen Resolution
Then in the screen that comes up, click on Make Text or Other Items Larger or Smaller
Then move the slider under Change the Size of All Items to Smaller and restart windows 8

Intel 6205 wireless not working with Lenovo W520

Loving the new W520... very fast, if only the wireless would work. Unable to get wireless interface functioning, won't even show up in ifconfig. I've appended requested wireless information, thanks in advance for any assistance.
1) Machine Brand and Model (PC/Laptop):
Lenovo W520
Intel Centrino Advanced-N 6205
Note: Wireless switch on lefthand side enabled, bluetooth led lights up but wireless does not.
2) Wireless Brand, Model and Wireless Chipset:
$ lspci -nn
03:00.0 Network controller [0280]: Intel Corporation 6000 Series Gen2 [8086:0085] (rev 34)
3 ) check interface:
ifconfig does not show wireless
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
4 ) Check for modules:
$ lsmod
iwlagn 215351 0
iwlcore 139688 1 iwlagn
mac80211 269644 2 iwlagn,iwlcore
cfg80211 167809 3 iwlagn,iwlcore,mac80211
5) Kernel boot messages
$ dmesg
[ 13.497936] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[ 13.497938] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[ 13.498058] iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 13.498089] iwlagn 0000:03:00.0: setting latency timer to 64
[ 13.498181] iwlagn 0000:03:00.0: Detected 6000 Series 2x2 AGN Gen2a, REV=0xB0
[ 13.499187] lp: driver loaded but no devices found
[ 13.502642] alloc irq_desc for 22 on node -1
[ 13.502645] alloc kstat_irqs on node -1
6 ) Network configuration
$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: 6000 Series Gen2
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 34
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0
resources: memory:d5300000-d5301fff
7 ) Scan for networks:
not relevant as no wireless interface appears
8 ) Ubuntu Version:
Ubuntu 10.10
9 ) Kernel/architecture (including 32 vs. 64 bit):
2.6.35-28-generic x86_64
10 ) Restarting the network:
sudo /etc/init.d/networking restart
* Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
[ OK ]
Additionally, modinfo shows the following:
$ modinfo iwlagn
filename: /lib/modules/2.6.35-28-generic/updates/compat-wireless-2.6.36/iwlagn.ko
alias: iwl4965
license: GPL
author: Copyright(c) 2003-2010 Intel Corporation <[email protected]>
version: in-tree:
description: Intel(R) Wireless WiFi Link AGN driver for Linux
firmware: iwlwifi-4965-2.ucode
firmware: iwlwifi-5150-2.ucode
firmware: iwlwifi-5000-2.ucode
firmware: iwlwifi-6000g2b-4.ucode
firmware: iwlwifi-6000g2a-4.ucode
firmware: iwlwifi-6050-4.ucode
firmware: iwlwifi-6000-4.ucode
firmware: iwlwifi-1000-3.ucode
srcversion: 8F7F4C6196599FCA596C837

Hi sparhk, and welcome.
One of the Lenovo staff who frequents the forum put out a call to help you in a private forum. I do a little Linux, so I poked into it. To my amazement my first Google hit was your thread where you indicate you have solved the problem. (At least, it _looks_ like you...)
May I respectfully suggest that a post back here indicating success would be a nice touch? That way anyone who passes by looking for help with this issue will have a better chance of finding it. For posterity, here it is (see post number 25):
[SOLVED] Intel 6205 wireless not working with Lenovo W520
Glad you got it working,
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Disable the Server Manager popup in Unattended.xml for Windows 2008 R2 is not working

I have made entry into Unattended file to stop the popup of Server Manager during first starup of windows 2008 R2. However it is not working out, but Disable Initial OCnfiguration task window is working fine. Below is my Unattended.xml
file:
<unattend xmlns="urn:schemas-microsoft-com:unattend">
<settings pass="windowsPE">
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" language="neutral" name="Microsoft-Windows-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35"
versionScope="nonSxS">
<ImageInstall>
<OSImage>
<WillShowUI>OnError</WillShowUI>
<InstallTo>
<DiskID>0</DiskID>
<PartitionID>1</PartitionID>
</InstallTo>
<InstallFrom>
<Path>K:\win28x64\Sources\install.wim</Path>
<MetaData>
<Key>/image/name</Key>
<Value>Windows Server 2008 R2 SERVERENTERPRISE</Value>
</MetaData>
</InstallFrom>
</OSImage>
</ImageInstall>
<UpgradeData>
<Upgrade>false</Upgrade>
</UpgradeData>
<Display>
<ColorDepth>16</ColorDepth>
<HorizontalResolution>1024</HorizontalResolution>
<RefreshRate>60</RefreshRate>
<VerticalResolution>768</VerticalResolution>
</Display>
<ComplianceCheck>
<DisplayReport>OnError</DisplayReport>
</ComplianceCheck>
<UserData>
<AcceptEula>true</AcceptEula>
</UserData>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-International-Core-WinPE"
processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<SetupUILanguage>
<UILanguage>en-US</UILanguage>
</SetupUILanguage>
<InputLocale>0409:00000409</InputLocale>
<SystemLocale>en-US</SystemLocale>
<UILanguage>en-US</UILanguage>
<UserLocale>en-US</UserLocale>
</component>
</settings>
<settings pass="specialize"><component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-ServerManager-SvrMgrNc"
processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<DoNotOpenServerManagerAtLogon>true</DoNotOpenServerManagerAtLogon>
</component><component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-OutOfBoxExperience" processorArchitecture="amd64"
publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<DoNotOpenInitialConfigurationTasksAtLogon>true</DoNotOpenInitialConfigurationTasksAtLogon>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" language="neutral" name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35"
versionScope="nonSxS">
<ComputerName>Siddu</ComputerName>
<RegisteredOrganization/>
<RegisteredOwner>BL-Target</RegisteredOwner>
<DoNotCleanTaskBar>true</DoNotCleanTaskBar>
<ShowWindowsLive>false</ShowWindowsLive>
<BluetoothTaskbarIconEnabled>false</BluetoothTaskbarIconEnabled>
<CopyProfile>false</CopyProfile>
<DisableAutoDaylightTimeSet>true</DisableAutoDaylightTimeSet>
<StartPanelOff>false</StartPanelOff>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-UnattendedJoin"
processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<Identification>
<JoinWorkgroup>Siddu</JoinWorkgroup>
<UnsecureJoin>false</UnsecureJoin>
<DebugJoin>false</DebugJoin>
</Identification>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Networking-MPSSVC-Svc" processorArchitecture="amd64"
publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<FirewallGroups/>
<DomainProfile_EnableFirewall>false</DomainProfile_EnableFirewall>
<PrivateProfile_EnableFirewall>false</PrivateProfile_EnableFirewall>
<PublicProfile_EnableFirewall>false</PublicProfile_EnableFirewall>
<PrivateProfile_DisableNotifications>true</PrivateProfile_DisableNotifications>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-TCPIP" processorArchitecture="amd64"
publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<Interfaces>
<Interface wcm:action="add">
<Ipv4Settings>
<DhcpEnabled>false</DhcpEnabled>
</Ipv4Settings>
<Ipv6Settings>
<DhcpEnabled>true</DhcpEnabled>
</Ipv6Settings>
<UnicastIpAddresses>
<IpAddress wcm:action="add" wcm:keyValue="1">192.168.79.171/24</IpAddress>
</UnicastIpAddresses>
<Identifier>PROV_DEVICE_MAC_ADD</Identifier>
<Routes>
<Route wcm:action="add">
<Identifier>0</Identifier>
<Prefix>0.0.0.0/0</Prefix>
<NextHopAddress>192.168.79.0</NextHopAddress>
<Metric>20</Metric>
</Route>
</Routes>
</Interface>
</Interfaces>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-DNS-Client" processorArchitecture="amd64"
publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<Interfaces>
<Interface wcm:action="add">
<DNSServerSearchOrder>
<IpAddress wcm:action="add" wcm:keyValue="1">192.168.79.168</IpAddress>
</DNSServerSearchOrder>
<EnableAdapterDomainNameRegistration>true</EnableAdapterDomainNameRegistration>
<Identifier>PROV_DEVICE_MAC_ADD</Identifier>
</Interface>
</Interfaces>
</component>
</settings>
<settings pass="oobeSystem">
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" language="neutral" name="Microsoft-Windows-Shell-Setup" processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35"
versionScope="nonSxS">
<UserAccounts>
<AdministratorPassword>
<Value>PROV_WIN_ADMIN_PASSWORD</Value>
<PlainText>true</PlainText>
</AdministratorPassword>
</UserAccounts>
<AutoLogon>
<Enabled>true</Enabled>
<Username>Administrator</Username>
<Password>
<Value>PROV_WIN_ADMIN_PASSWORD</Value>
<PlainText>true</PlainText>
</Password>
<LogonCount>3</LogonCount>
</AutoLogon>
<Display>
<ColorDepth>32</ColorDepth>
<HorizontalResolution>1024</HorizontalResolution>
<RefreshRate>60</RefreshRate>
<VerticalResolution>768</VerticalResolution>
</Display>
<FirstLogonCommands>
<SynchronousCommand wcm:action="add">
<CommandLine>c:\BLProv\wrapper.bat</CommandLine>
<Description>Lite Touch new OS</Description>
<Order>1</Order>
</SynchronousCommand>
</FirstLogonCommands>
<OOBE>
<HideEULAPage>true</HideEULAPage>
<NetworkLocation>Other</NetworkLocation>
<ProtectYourPC>3</ProtectYourPC>
<SkipUserOOBE>true</SkipUserOOBE>
<SkipMachineOOBE>true</SkipMachineOOBE>
</OOBE>
<RegisteredOrganization/>
<RegisteredOwner>BL-Target</RegisteredOwner>
<TimeZone>Dateline Standard Time</TimeZone>
</component>
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-International-Core"
processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<InputLocale>0409:00000409</InputLocale>
<SystemLocale>en-US</SystemLocale>
<UILanguage>en-US</UILanguage>
<UserLocale>en-US</UserLocale>
</component>
</settings>
<settings pass="offlineServicing">
<component xmlns:wcm="http://schemas.microsoft.com/WMIConfig/2002/State" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" language="neutral" name="Microsoft-Windows-PnpCustomizationsNonWinPE"
processorArchitecture="amd64" publicKeyToken="31bf3856ad364e35" versionScope="nonSxS">
<DriverPaths>
<PathAndCredentials wcm:action="add" wcm:keyValue="1">
<Path>C:\Drivers</Path>
</PathAndCredentials>
<PathAndCredentials wcm:action="add" wcm:keyValue="2">
<Path>X:\Drivers</Path>
</PathAndCredentials>
</DriverPaths>
</component>
</settings>
<cpi:offlineImage xmlns:cpi="urn:schemas-microsoft-com:cpi" cpi:source="wim:K:\win28x64\sources\install.wim#Windows Server 2008 R2 SERVERENTERPRISE"/>
</unattend>

Hi,
Since this issue is more related with Windows Server, I have helped you move this thread to that forum so that you could get help better.
Karen Hu
TechNet Community Support

Windows media player will not work as no DVD driver

Had to format disk (trojan) & reinstall Windows XP home. Now Windows media player will not work as no DVD Driver, can I download from Toshiba site?

Hi
Usually the Windows media Player is not able to play DVD movies IF no plug-ins were installed.
To watch DVD movies you can use the programs like WinDVD or PowerDVD.
Such programs were designed especially for the DVD playing!
But you can also visit the Microsoft website and search for plug-ins for Windows Media player.
Then you could download and install it to play DVD with WMP
Best regards

I am running Office 2013. Trying to sync my reminders with my iphone using icloud for windows, but it is not working. Can anyone please help?

I am running Office 2013. Trying to sync my reminders with my iPhone 5c version 7.1.2 using icloud for windows, but it is not working. Can anyone please help?

Windows media player is not working

windows media player is not working while i am playing any audio/video. it is saying server execution is failed

Please post your Product number (please don’t post your serial number).
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

T440p (Windows 7) - Realtek wireless not working, repeatedly being disabled in Device Manager

Similar Messages

Maybe you are looking for