T500 and Windows 7.

I have upgraded my T500 from Vista to Windows 7 ( 32 bit ) and everything went Ok but 2 issues :
1- I tried to instal Rescue and Recovery for Windows 7 ( 32 bit ) but it keeps showing an error message that there is a ( .tvt ) file missing .
2- I'm still looking for the Passwords Manager software.
Any help pleae ?
Regards,

Why don't you guys start by looking on lenovo support/drivers section?
sound like the most obvious thing to do. that's what I found in 23 seconds:
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-73641

Similar Messages

Thinkpad t500 and wifi card realtek RTL8192SE[solved]

I Buy a Lenovo Thinkpad T500 and the wireless adapter does not work in linux.
11b/g/n Wireless Lan Mini-PCI Express Adapter II.
lspci say:
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at f4200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
lspci -n:
03:00.0 0280: 10ec:8172 (rev 10)
I need to buy another usb, pcmcia or mini pci-e wireless card.
Can you recommend one that works well? Because I never work with wifi cards on linux.
sorry my poor english
EDIT 21/07/09: add more information (thinkwiki):
http://www.thinkwiki.org/wiki/ThinkPad_ … Adapter_II
EDIT 22/10/09:
Finally came the expected driver, I think it's premature but it works perfectly.
Here the driver (r8192se_pci):
32bits: http://launchpadlibrarian.net/33927923/ … 009.tar.gz
64bits: http://launchpadlibrarian.net/34090326/ … bit.tar.gz
untar; make; make install; reboot and enjoy it
I test it with:
netcfg
standar commands:
ifconfig wlan0 up
iwlist wlan0 scan
iwconfig wlan0 essid MySsid
wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
dhcpcd wlan0
The first time I compile the module, function correctly, but after scan for available networks I haven't any results.
Recompile and everything worked again
[b]I edit the wiki, pleased read it and help me because my English is a bit basic.
thanks
Last edited by takedown (2009-10-23 00:55:44)

Please note that the T500 has different hardware configurations.
Other options in wireless card (for the T500): intel 5100 - intel 5300.
This models work fine under linux
lspci -vv:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f4400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 41c9
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 2114
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f4200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fc226800 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: heci
Kernel modules: heci
00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) (prog-if 85 [Master SecO PriO])
Subsystem: Lenovo Device 20ea
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 1828 [size=8]
Region 1: I/O ports at 180c [size=4]
Region 2: I/O ports at 1820 [size=8]
Region 3: I/O ports at 1808 [size=4]
Region 4: I/O ports at 1810 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel modules: ata_generic, pata_acpi, ide-pci-generic
00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) (prog-if 02 [16550])
Subsystem: Lenovo Device 20ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1830 [size=8]
Region 1: Memory at fc024000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fc025000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Mask- 64bit+ Count=1/1 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [e0] PCIe advanced features <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc226c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fc020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4300000-f43fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 1, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: 00000000f4000000-00000000f40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 3, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=14, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 00000000f4100000-00000000f41fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 4, PowerLimit 6.500000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq+ LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Mask- 64bit- Count=1/1 Enable+
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: Lenovo Device 20f3
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18c0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18e0 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) (prog-if 00 [UHCI])
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Capabilities: [50] PCIe advanced features <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fc227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCIe advanced features <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=15, subordinate=18, sec-latency=32
I/O behind bridge: 00005000-00008fff
Memory behind bridge: f4800000-f7ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f3ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Lenovo Device 20f4
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel modules: iTCO_wdt
00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device 20f8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at 1c48 [size=8]
Region 1: I/O ports at 183c [size=4]
Region 2: I/O ports at 1c40 [size=8]
Region 3: I/O ports at 1838 [size=4]
Region 4: I/O ports at 1c20 [size=32]
Region 5: Memory at fc226000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Mask- 64bit- Count=1/16 Enable+
Address: fee0300c Data: 4199
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] PCIe advanced features <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc227400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. Device e020
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at f4300000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Mask- 64bit+ Count=1/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-e0-4c-ff-fe-22-55-88
15:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
Subsystem: Lenovo Device 20c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f4800000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=15, secondary=16, subordinate=17, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: 80000000-83fff000
I/O window 0: 00005000-000050ff
I/O window 1: 00005400-000054ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
15:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04) (prog-if 10 [OHCI])
Subsystem: Lenovo Device 20c7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f4801000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
15:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
Subsystem: Lenovo Device 20c8
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f4801800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci
15:00.3 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc
15:00.4 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 11)
Subsystem: Lenovo Device 20ca
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
15:00.5 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 11)
Subsystem: Lenovo Device 20cb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at f4802400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

T500 and SUSE Linux

Hi, There,
I would like to install the SUSE Linux on T500 as I had enough issues with the Windows VISTA and Windows 7 is not officially released yet. Has anybody out there recommend using the SUSE on T500. Lenovo site itself doesnt seem to offer the drivers and the thinkvantage software for Linux. So I'm I going to miss all that Thinkvantage stuff? Also without the Lenovo Vendor drivers will the system be stable and will not miss any essential features.
Cheers,
Max.
Solved!
Go to Solution.

Not all features in thinkvantage may be available for SuSE Linux,you can wait for windows 7 if your intention is to use a good OS.
Cheers and regards,
• » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
●๋•کáŕádhí'ک díáŕý ツ
I am a volunteer here. I don't work for Lenovo

T500 with Windows 7 64bit upgraded to ADATA SSD S599 (SandForce) BSOD after wake up

Hello
I have just upgraded my T500 with the ADATA SSD S599 (SandForce based) and it gets real performance boost.
Everything works fine except Sleep mode, specifically waking up: when I open the lid to recover from the sleep mode I got the Blue Screen of Death most of the time.
Tried with Microsoft built-in AHCI driver as well as Intel drivers (from Lenovo drivers page)
Installed all the newest drivers from Lenovo's site. Hibernation works without problem.
Debugging memory.dmp show paging pool related problems, sometimes referring to hard disk problem.
Found on OCZ forum that Sand Force based disks (for example: Vertex 2) may behave similary.
Can anyone confirm if such a disks works well in T500 with 64 bit windows 7?
Thank you.

ADATA SSD S599 is supported in Windows 7 x64.
Go to
http://www-307.ibm.com/pc/support/site.wss/migr-70443.html
and try to install every hotfix for T500. (and update firmware and drivers if possible.. )

T-500 and Windows Server 2008 R2 RTM

My setup:
T-500 dual booting via VHD - Windows 7 and Windows Server 2008 R2 (both 64-bit).
My problem:
I'm having a devil of a time with this one. I get random BSOD'd in my Server 2008 R2 installation, but my Win7 install is rock solid. Sometimes it's right away, sometimes after a few minutes, sometimes when trying to use WordPad. I cannot get my wireless card (Intel 5100 AGN) to work along with video drivers for my ATI card, so I'm leaning towards a driver issue. I'm trying to use the Win7 drivers for anything that's missing drivers at the moment, since they are the same under the hood, so to speak.
Has anyone else experimented with this setup and/or run into similar problems? Thanks!
T500: T9400 (2.53GHz), 4GB RAM, 160GB 7200rpm, 15.4in 1680x1050 WSXGA+ LCD, 256MB ATI Radeon HD3650, DVDRW, Intel 802.11agn wireless, AT&T WWAN, Bluetooth, Modem, 1Gb Ethernet, 9c Li-Ion, Windows 7 Ultimate x64 RC (Build 7100)

You shouldn't have any big issues, but there are a couple of gotchas that Server versions of Windows have (a notable one is the Bluetooth stack). Those are somewhat detailed in the review, though (and that blog also details how to get other features of Server 2008 R2 running).

T400, motherboard replaced and Windows 7 says it is not a legal license

Hi, we have a T400, it had a problem with the motherboard and the local tech support replaced it. Now Windows says that the Windows 7 is not legal, that a Legal version of Windows should be buyed. This is a Windows 7 32bits, English. Pre-installed on the ThinkPad T400. In System Properties, at the botom, it says: Windows Activated But when I run the Windows Genuine Website, it says it is not a legal copy. Also, a pop-up appears near the time and says it is not a legal copy of windows. Should I call Microsoft an re-activate Windows 7? Many thanks Oliver

Hi, I checked the BIOS and it has the same serial and type as in the printed label on the botom of the notebook. Also, checked que SLIC and it is present. I used everest software in order to check: http://www.mydigitallife.info/2007/03/03/slic-table-slicbin-or-acpislicbin-bios-file-for-oems-downlo... I will try these steps in order to see what happends: http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T410-update-new-BIOS-SLIC-misssing/m-p/2851... Regards, Oliver

Problem with Sessions and window.open

Hi,
Hi everyone,
Help Please!!!
I am working with Sevlet session objects and HTML forms and windows. I have an HTML form for the user to supply a username and password. Once the user clicks submit I need to open another browser window that has no toolbar, no location, no status bar, etc. The user should also be able to go back to that login screen and login again and open a 2nd, 3rd, etc. instance of the application. My problem is that each application is being asigned the same sessionId. I believe it is being asigned to the main login window and thus to the other child windows it opens. Is there a way to work around this? Do I need to make the user open another browser window to login? I need to be able to let the user open multiple instances of the application with unique session ids for each.
Any insight is GREATLY appreciated on this topic. Anything you can tell me about sessions (Java), IE, window.open would help greatly!
THANK YOU IN ADVANCE!!!
MA

To achieve this, you must introduce another level of
abstraction to the Servlet specifications. When you
work with JSP/Servlets you use mostly the HttpSession
to handle user related tasks, and the aplication
context, for things that are common to all users. But
inside the HttpSession scope, you want to create
containers that have 'smaller' scope and are uniquely
identified.
A ipothetical scenario :Let's say that you must have
multiple connections to several databases, on each
database user rights beeing diferrent, and you must be
able to track user actions globaly, and eventualy
capture a 'Close Application event' and close all db.
connections.
1. when the user first accesses the login frame create
the HttpSession. In the HttpSession object, store a
Hastable (let's call it 'ConnectionTable'). Each
object in the Hashtable must identify uniqely a
database connection. Now, to create unique identifiers
ids, make the keys in the hashtable java.lang.Long
objects, created using System.getCurrentTimeMillis().
This guaranties there will be no possible confusion.
From each new open window, on each request to the
server, along with the usefull parameters, send the
connection identifier. When proccessing the request,
select the object from the Hastable wich corresponds
to the ID.
2. Now, the values in the ConnectionTable, must act as
the containers that I mentioned in the first
paragraph. The simplest way to do this is to have
again a Hashtable derived class to do the job, wich
exploses methods similar to HttpSession: setAttibute (
Object key, Object value) and getAttibute ( Object
key, Object value). This container may use internally
a Hashtable to store object, and explose only the
getAttribute and setAttribute methods for clarity. Any
way, this is a problem of implementation. Let's call
this class CustomSession.
Now, a textual activity diagram:
1 user accesses the main page, you start a new
HttpSession; In the HttpSession object, store the
ConnectionTable object.
2. the user enters the userID and pwd and adatabase
name, and a new window is opened. Let's supose the
data entered is valid.
3. when you process the login data, you create a new
CustomSession object. you put in it whatever you would
put in your HttpSession. You generate a unique
identifier using System.CurrentTimeMillis(). Put the
CustomSession object in the ConnectionTable, using the
generated id as key. Send the response.
..... later on .....
100. the user asks for a particular action to be
performed - e.g. a row deletion. The page contains a
form with text field where the user introduces the
row number, a submit button and a hidden input with
the ID.
101. you process the data. Get the ID from the request
object, get the ConnectionTable from the session, get
the CustomSession using the ID as key, do whatever
your logic was doing, but obtaining the objects from
the CustomSession instead of HttpSession
NicNic,
Very slick idea. I think that it could work and it seems that there would be not security issues because the id that you would store on the client side is the Unique Identifier and not the actual Session Id. Do you forsee any security issues for this implementation?

How can I make an icon that links to a webpage that works with Mac and Windows??

Hi!
I burn CDs with my photos and send them to clients. Besides the photos folder, I would like to include a file (similar to the .webloc files on the Mac Desktop) that can be clicked and it will be linked to my website - it will open up a browser window and go to my website . Is it posssible to make one of these icons that works with both Macs and Windows machines? Thanks!

Now it works! Thanks, Denico!
The reason I saved to text: The first time I followed your instructions, it did not work. I tried to figure out what I did wrong and saw that you wrote to "save as plain text." I did not know what this means and there was no option available to save a plain text. So I looked around and saw "save as stationery" and I guessed that maybe that was what you meant. And after that, it worked! But the next thing you know, the icons started duplicating themselves.
I guess I had made a different mistake in the beginning and I fixed it without knowing what it is.
Thanks for clearing that up.
But just one question. WHY does saving as "stationery" make an icon duplicate itself?

Is Verizon going to acknowlege the problems with FIOS and Windows Vista

For months now, I have been reading the numerous problems Fios internet customers are having with Fios internet/Actiontech Router and Windows Vista and there has been no acknowledgement by Verizon of this current major issue.
I have also experienced the exact same issue for months now since I switched to Verizon FIOS internet. Previously I had Comcast HSI using my Windows Vista laptop. I had their service for over a year and I NEVER has a problem with the Windows Vista globe icon disappearing and loosing internet connection. The Globe always stayed on and never went away and I never lost connection when I had Comcast
I had Verizon FIOS installed last September with my Windows Vista computer and my wireless internet connection started to drop from day 1 and it has been a daily occurrence for over 5 months now. It has gotten so bad, I have had to hardwire my laptop to to be able to use the internet uninterrupted.
This is what daily scenario is:
When I turn on my laptop(with Windows Vista, I can initially get full internet access(with the globe on and it says "Local and internet). After about 10 minutes or less, the globe switches to "local only" and I can still get internet access. After another 5 or so minutes, a large X covers the globe and I lose internet connection entirely. The actiontech router wireless signal is no longer listed as one of the wireless networks. The only way for me to regain internet access is either to restart my laptop or reboot the actiontech router.
Numeorus posts here, over by DSL forums(Broadband Reports),Microsoft's website and a few othere websites detail this issue.
I am extremely shocked and surprised that Verizon has not tried to fix this issue by working with both the makers of the Actiontech Router as well as Microsoft to find out what the problem is and how to fix it.
I would just like to reiterate I strongly believe this is primarily a FIOS internet issue since I previously had Comcast HSI for over a year with the same Windows Vista laptop and I NEVER had that problem. Also, I can connect to my neighbors wireless connection(she uses Comcast HSI) and when I do, the globe stay on all the time on my computer and the internet does not lose connection.
I know that there are a couple of Verizon employees here. Please tell the higher ups who handle FIOS internet that this is a major issue that needs to be resolved as soon as possible.
P.S: Please don't tell me to go by my own router because then, I will have to deal with the issues of setting it up to work with Fios TV and the related VOD, widgets, remote DVR compatability issues to deal with. I don't think I can deal with the additional headaches.

FIOS is short for fiber optics. fiber optics is different technology than DSL.
With that said, if you search the Microsoft databases for vista issues with fiber optics, (CURRENTLY THERE IS ONLY ONE PROVIDER OF FIBER TO THE HOUSE, that being Verizon, so yes you can also search Vista issues with verizon and\or fios) and you will find that Microsoft already acknowledges this issue with their software. AND they offer you a fix.
cjacobs001

IPhone 5 iOS 6.1.4 and Windows 7 x64 USB Driver Issues

Been pulling my hair out with this one for the last week or so and haven't had any luck finding anything on the forums or the web regarding a solution short of a full reinstall of Windows 7 which I am not prepared to do at this time; so hoping someone here can shine some light on this for me
I have a iPhone 5 that is updated to iOS 6.1.4 and a recently built Windows 7 64-bit machine. All of my other USB devices function fine (keyboard, mouse, Xbox 360 wireless receiver for Windows, and a Seagate 2TB external USB drive). I've downloaded the most recent version of iTunes, installed successfully and then attempt to plug in my phone to sync. I get the standard Windows *ding* that I've attached a device and 1 of 2 things happens (I haven't been able to determine what causes one reaction to happen versus the other): Windows will successfully install the 'Apple USB Mobile Device Driver' successfully and it will appear under my USB devices in Device Manager. However - iTunes will not recognize the phone and I cannot see it in Windows either. In the 'Devices and Printers' snap-in my iPhone will appear under 'Unspecified Devices' as the 'Apple USB Mobile Device'. The iTunes diagnostics fail to find a connected device so the tests fail. As soon as I unplug the device, the strangest thing happens: Windows will start trying to install a device driver and after a few seconds it will fail stating that the "MTP Device Driver" installation failed because the device was unplugged. iTunes also thrown an error "iTunes cannot connect to this iPhone" throwing error code 0XE8000065 (I've also seen error code 0XE8000085 as well)
After some finagling, I've managed to get Windows to recognize the device under 'Portable Devices' in Device Manager as an "MTP USB Device" using the generic driver. At this point, I've tried updating the driver and manually specifying the Apple USB driver located in the C:\Program Files(x86)\Common Files\Apple\Mobile Device Drivers which updates successfully but then changes the device to "Apple USB Mobile Device" and moves it under the USB Devices in Device Manager; and Windows nor iTunes can see it even still.
I've tried removing iTunes several times and ensuring that all remnants of the installation are gone (registry and folders on the installation drive) and have disconnected all my USB devices short of the keyboard and mouse and still I get the same results. At this point, I'm afraid that a re-install of Windows is going to be the solution; but it's a drastic one (I have a SSD drive where Windows is installed along with all of my games for faster load times/better performance and do not want to have to redownload\reinstall all of them) and I'm not prepared to undertake it at this time, which is why I'm posting here
I've used a utility called USBDeview that sees my phone is connected - so I know from a functional standpoint that my USB ports are good and working. I also know the cable is good too - my daughter's PC (Windows 7 32-bit with NO iTunes) immediately sees the device when I plug it in, installs the drivers, recognizes it as an iPhone and I can then see/browse it in Windows Explorer like I would normally expect. My work PC (Windows 7 64bit, NO iTunes) sees the device just fine as well. I would immensely appreciate anyone that has seen this issue or has any additional solutions I can try.
It's also worth mentioning that I've never used Kapersky antivirus so the UPPERFILTERS value in the registry that I've seen as a solution on some forums is not present on my machine. I'm using Microsoft Security Essentials as my antivirus (no flaming please lol - it meets my needs and is extremely lightweight, which is why I'm using it on a gaming rig) and it's not indicating any issues. I've also tried running iTunes as an administrator (even though my account is a local admin on the machine) and that does not have any effect either.
If there is anything I left out, please let me know; and I thank you in advance!

AphexTwin wrote:
- no Apple input?
Of course not. Didn't you bother to read the TOU of this forum? This is a USER TO USER technical support forum. Apple doesn't post here.

IPod Nano: Error Message "The USB device has malfunctioned and Windows does not recognise it"

Hi everyone, I just received 2 brand new iPod Nanos for my kids for Christmas, thought I'd be smart and sync them both now before wrapping them so I don't have to be messing around with them on the day. One synced without a problem, then using the same cable, same computer, same USB port, the 2nd one came up with "The USB device has malfunctioned and Windows does not recognise it" I've tried restarting my computer, unplugging and reinserting the USB. Is there anthing else I can try before returning it? Thanking you for any help.

I have solved my problem, I ended up ringing Apple and got an awesome lady who told me to reset it by pressing the sleep button and menu button together for about 10 seconds and once it actually turned on for the first time the computer then recognised it, so it's all good, :-) Thank you lovely lady!

ITunes and Windows 8 Home Sharing (Possible Fix)

If this fix has been posted elsewhere then I apologize, but I wanted to share what I stumbled on as a possible for for iTunes Home Sharing and Windows 8. I did a lot of port forwarding, both on my router and my Norton firewall, but nothing seemed to help. After a few minutes my Apple TV and iOS devices would stop seeing my iTunes library. The only way to fix it was to reboot the router.
On a whim I looked in my Device Manager and found under Network Adapters a device called Microsoft Kernel Debug Network Adapter. I disabled this, rebooted my computer, and have since no issues with Home Sharing. It's only been a few hours, but that is the longest I've gone since installing Windows 8. I'll look in the morning to see if it still works.
So give this method a try and see what happens. Hopefully it will fix your problems.

Here are the three steps I took to get Home Sharing working successfully on Apple TV. This has worked for the better part of a week so hopefully it will work well for others.
In your software firewall create two new Inbound Rules. Open port 3689 (TCP) and port 5353 (UDP) to All Programs.
If your hard drive goes to sleep after a certain period, be sure to change to something greater than 30 min. (Control Panel -> Power Options -> Change Plan Settings -> Change Advanced Power Settings -> Hard disk -> Turn off hard disk after -> Setting)
On your Apple TV change when it goes to sleep. I changed mine to 10 hours.
This seems to keep the connection alive. On occassion it will look like it gets stuck loading, but just let it go. At some point it wil kick on. If you generates a connection error just try loading the media again and it should start.

Software and Windows 8

Hi there, can somebody PLEASE tell me how i can download the desktop software for my pc. I have a Blackberry 9300 and Windows 8 on my pc!!! URGENT

I would recommend the most recent Desktop Software, version 7. Download it here:
https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

RemoteFX and windows 8.1

Hello,
I am currently running a VDI environment with server 2012 servers including a RDCB, RDVH, RDSH, RDWA and windows 8 clients. I am using remoteFX on the windows 8 clients with the help of 3 nvidia Quadro 6000 cards. RemoteFX works perfectly in windows 8; however,
I built a windows 8.1 VM and remote FX will not work in this VM. When I log on to the vm and look under device manager the remoteFX device is listed but it gives an error of 43. All of the vm's have one monitor set in the remoteFX settings. In the event viewer
of the windows 8.1 VM I am getting an error under RemoteDesktop Services vGPU-kModeDriver "The virtual GPU synthetic devie failed" and the other accompanying error is "The RDVGM kernal mode driver failed to start" I have removed all of
the windows 8 VM's to confirm that all of the available memory of the GPU was not used and this didn't get any different results. The only difference I see is that one guest os is windows 8 and the other is 8.1. Does remoteFX not work in windows 8.1 by chance?
Both OS's are Enterprise as well.
Thanks for any help,
Scott

Hi Scott,
Sorry for the late.
I think the edition of win8 VM that has been enabled RemoteFX is enterprise .
(To use RemoteFX , guest os on hyper-v host should be enterprise edition )
For details please refer to following link:
http://blogs.msdn.com/b/rds/archive/2012/11/26/remotefx-features-for-windows-8-and-windows-server-2012.aspx
Best Regards
Elton
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

RH10 and Windows 8.0/8.1

Hi Everyone,
Please can some advise what the current state of play is with RH10 and windows 8.0 and window 8.1.
i.e does it work properly?
I am expecting to be asked to document a package running under window 8.0 or 8.1 shortly wondered if my copy of RH 10 will still work ok for this? Our main output format is web help.
Secondly when is the next version of RH due that is compatible with office 2013?
Thanks

Thanks Willam, it was more about the version that ships than the versions that can be installed that I wanted to clarify.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge

T500 and Windows 7.

Similar Messages

Maybe you are looking for