T510 - NVS3100M only connected via PCIe Version 1.1 instead of PCIe2.0 ?
Hi,
GPU-Z reports only PCIe 1.1.
Is there any way to activate PCIe 2.0?
thx
Hi,
As I know, recent browsets should use http 1.1, have you tried to force the http 1.1 via registry?
Open registry editor
Click Start, click Run, type regedit, and then click
OK.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\Software\Microsoft\Windows\CurrentVersion\Internet Settings
On the Edit menu, point to New, and then click
DWORD Value.
Type EnableHTTP1_1, and then press ENTER.
Right-click EnableHTTP1_1, and then click Modify.
Type 1, and then click OK.
On the Edit menu, point to New, and then click
DWORD Value.
Type ProxyHttp1.1, and then press ENTER.
Right-click ProxyHttp1.1, and then click Modify.
Type 1, and then click OK. click F5 to refresh the registry.
Exit Registry Editor.
And the link you pasted above (answer.microsoft.com) mentioned that this issue could be related with Blue Coat proxy, as a test, I suggest you set IE to "Automatically detect settings" instead of the proxy, check if it is the culprit.
Yolanda Zhu
TechNet Community Support
Similar Messages
-
My ipod touch (4th G) only connects via wifi, not via cable. The cable works with my iPad, so it's not that. Help?
1. Turn the router, iPad and printer off.
2. Turn on the router and then wait 30 seconds to let it complete its start-up process.
3. Turn on printer and then wait 30 seconds to let it complete its start-up process.
4. Turn on your iPad and test print. -
EHWIC-4G-LTE-V only connects via 1xRTT
I've got an EHWIC-4G-LTE-V card in a 2921 router and am only able to connect via 1xRTT. Can someone take a look at the output below and provide some insight as to why I can't connect via LTE? Thank you.
BroadbandLabv233#sho cell 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9600M_03.05.10.06
Modem Firmware built = 2012/11/12 15:07:45
Hardware Version = 10
Integrated Circuit Card ID (ICCID) = 89148000001035643492
Mobile Station Identifier (MSID) : 9802145106
Electronic Serial Number (ESN) = 0x8028B8D1 [12802668753]
Preferred Roaming List (PRL) Version = 0
Profile Information
====================
Profile 1 = INACTIVE **
PDP Type = IPv4
Access Point Name (APN) =
Authentication = None
Username:
Password:
Profile 3 = ACTIVE*
PDP Type = IPv4
PDP address = 166.251.23.6
Access Point Name (APN) = SO01.VZWSTATIC
Authentication = None
Username:
Password:
Primary DNS address = 198.224.183.135
Secondary DNS address = 198.224.182.135
* - Default profile
** - LTE attach profile
Data Connection Information
===========================
Data Transmitted = 5428 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = ACTIVE
IP address = 166.251.23.6
Primary DNS address = 198.224.183.135
Secondary DNS address = 198.224.182.135
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current Service = Packet switched
Current System Identifier (SID) = 139
Current Network Identifier (NID) = 65535
Current Service Status = Normal
Packet switch domain(PS) state = Attached
Registration state = Registered
Radio Information
=================
1xRTT related info
Current RSSI = -77 dBm
Radio power mode = ON
LTE Technology Preference = AUTO
LTE Technology Selected = eHRPD(1xRTT)
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
BroadbandLabv233#sho run
Building configuration...
Current configuration : 10686 bytes
! Last configuration change at 19:39:23 UTC Wed Aug 20 2014 by @dm1n
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname BroadbandLabv233
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.153-3.M2.bin
boot-end-marker
logging buffered 4096 informational
logging console informational
no aaa new-model
ip flow-cache timeout active 1
ip domain name aaanet.com
ip cef
no ipv6 cef
multilink bundle-name authenticated
chat-script lte "" "AT!CALL1" TIMEOUT 20 "OK"
license boot module c2900 technology-package securityk9
license boot module c2900 technology-package datak9
redundancy
controller Cellular 0/0
track 100 ip sla 100 reachability
delay down 10 up 20
class-map type inspect match-any INSPECT-TO-ROUTER-CLASS
match access-group name INSPECT-TO-ROUTER-ACL
class-map type inspect match-any INSPECT-FROM-ROUTER-CLASS
match access-group name INSPECT-FROM-ROUTER-ACL
class-map type inspect match-any INSPECT-INSIDE-TO-OUTSIDE-CLASS
match protocol ftp
match protocol tcp
match protocol udp
match protocol icmp
class-map type inspect match-any PASS-TO-ROUTER-CLASS
match access-group name PASS-TO-ROUTER-ACL
class-map type inspect match-any PASS-FROM-ROUTER-CLASS
match access-group name PASS-FROM-ROUTER-ACL
policy-map type inspect INSIDE-TO-OUTSIDE-POLICY
class type inspect INSPECT-INSIDE-TO-OUTSIDE-CLASS
inspect
class class-default
drop log
policy-map type inspect TO-ROUTER-POLICY
class type inspect INSPECT-TO-ROUTER-CLASS
inspect
class type inspect PASS-TO-ROUTER-CLASS
pass
class class-default
drop log
policy-map type inspect FROM-ROUTER-POLICY
class type inspect INSPECT-FROM-ROUTER-CLASS
inspect
class type inspect PASS-FROM-ROUTER-CLASS
pass
class class-default
drop log
zone security INSIDE
description internal interfaces
zone security OUTSIDE
description external interfaces
zone-pair security INSIDE-TO-OUTSIDE source INSIDE destination OUTSIDE
service-policy type inspect INSIDE-TO-OUTSIDE-POLICY
zone-pair security FROM-ROUTER source self destination OUTSIDE
service-policy type inspect FROM-ROUTER-POLICY
zone-pair security TO-ROUTER source OUTSIDE destination self
service-policy type inspect TO-ROUTER-POLICY
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 2
encr aes
authentication pre-share
group 5
crypto isakmp key <removed> address <removed>
crypto isakmp keepalive 10 periodic
crypto isakmp aggressive-mode disable
crypto ipsec transform-set HQ-vpn esp-3des esp-md5-hmac
mode tunnel
crypto map Branch-VPN-Policy 10 ipsec-isakmp
description VPN Tunnel to AAA-HQ
set peer <removed>
set transform-set HQ-vpn
match address Remote-HQ-acl
interface Loopback0
ip address <removed> 255.255.255.255
interface Tunnel0
bandwidth 512
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
ip tcp adjust-mss 1380
ip ospf cost 150
shutdown
tunnel source GigabitEthernet0/1
tunnel mode ipip
tunnel destination <removed>
interface Tunnel1
bandwidth 512
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
ip tcp adjust-mss 1380
ip ospf cost 150
tunnel source Cellular0/0/0
tunnel mode ipip
tunnel destination <removed>
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.10
description Data Network
encapsulation dot1Q 10
ip address <removed>
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
zone-member security INSIDE
interface GigabitEthernet0/0.20
description Voice Network
encapsulation dot1Q 20
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
interface GigabitEthernet0/0.40
description Management
encapsulation dot1Q 40
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
interface GigabitEthernet0/1
bandwidth 50000
ip address <removed>
no ip unreachables
ip flow ingress
ip flow egress
ip nat outside
no ip virtual-reassembly in
zone-member security OUTSIDE
shutdown
duplex auto
speed auto
pppoe enable group global
crypto map Branch-VPN-Policy
interface GigabitEthernet0/2
no ip address
duplex auto
speed auto
interface Cellular0/0/0
ip address negotiated
ip access-group NO-BOUNCE out
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
zone-member security OUTSIDE
encapsulation slip
ip tcp adjust-mss 1000
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
async mode interactive
crypto map Branch-VPN-Policy
router ospf 100
network <removed> area <removed>
network <removed> area <removed>
network <removed> area <removed>
ip local policy route-map sla-route
ip forward-protocol nd
no ip http server
no ip http secure-server
ip flow-export source Loopback0
ip flow-export destination <removed> 2055
ip nat inside source route-map Broadband-NAT interface GigabitEthernet0/1 overload
ip nat inside source route-map Cell-NAT interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 <removed> track 100
ip route <removed> track 100
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0 10
ip route <removed> Cellular0/0/0 10
ip route <removed> Tunnel0
ip route <removed> Tunnel1
ip access-list extended INSPECT-FROM-ROUTER-ACL
permit udp any any eq isakmp
permit icmp any any
permit udp <removed> any eq syslog
ip access-list extended INSPECT-TO-ROUTER-ACL
permit icmp any any echo
ip access-list extended NAT
permit ip <removed> any
ip access-list extended NO-BOUNCE
permit ip host <removed> any
deny ip any any log
ip access-list extended PASS-FROM-ROUTER-ACL
permit udp any eq bootpc any eq bootps
permit esp any any
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended PASS-TO-ROUTER-ACL
permit udp any eq bootps any eq bootpc
permit esp any any
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended Remote-HQ-acl
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended sla-packets
permit ip host <removed> host 8.8.8.8
ip sla auto discovery
ip sla 100
icmp-echo 8.8.8.8 source-interface GigabitEthernet0/1
frequency 10
ip sla schedule 100 life forever start-time now
logging source-interface Loopback0
dialer-list 1 protocol ip list 1
route-map Broadband-NAT permit 10
match ip address NAT
match interface GigabitEthernet0/1
route-map sla-route permit 10
match ip address sla-packets
set ip next-hop <removed>
set interface Null0
route-map Cell-NAT permit 10
match ip address NAT
match interface Cellular0/0/0
snmp-server enable traps vstack operation
access-list 1 permit <removed>
control-plane
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
modem InOut
no exec
speed 144000
line vty 0 4
login local
transport input all
scheduler allocate 20000 1000
ntp update-calendar
ntp server 10.10.32.179
ntp server 10.10.32.180
event manager session cli username "<removed>"
event manager applet Primary_INET_Down
event track 100 state down maxrun 90
action 1.0 syslog msg "Ping has failed, Primary circuit unable to reach internet!"
action 1.1 cli command "enable"
action 1.2 cli command "configure terminal"
action 1.3 syslog msg "shutting broadband tunnel0"
action 1.4 cli command "interface tunnel 0"
action 1.5 cli command "shutdown"
action 1.6 syslog msg "Clearing crypto"
action 1.7 cli command "do clear crypto session"
action 1.8 cli command "do clear crypto sa"
action 1.9 cli command "do clear crypto isakmp"
action 2.0 syslog msg "clearing route table"
action 2.1 cli command "do clear ip route *"
action 2.2 syslog msg "clearing NAT translations"
action 2.3 cli command "do clear ip nat translation *"
action 2.4 cli command "do clear ip nat translation forced"
action 2.5 syslog msg "enabling 4G card and tunnel1"
action 2.6 cli command "interface cellular 0/0/0"
action 2.7 cli command "no shutdown"
action 2.8 cli command "interface tunnel1"
action 2.9 cli command "no shutdown"
action 3.1 syslog msg "End of script. 4G enabled!"
event manager applet Primary_INET_Recovered
event track 100 state up maxrun 90
action 1.0 syslog msg "Broadband ping has recovered, shutting down 4G card and tunnel1 to limit data usage!"
action 1.1 cli command "enable"
action 1.2 cli command "configure terminal"
action 1.3 cli command "interface cellular 0/0/0"
action 1.4 cli command "shutdown"
action 1.5 cli command "interface tunnel 1"
action 1.6 cli command "shutdown"
action 1.7 syslog msg "clearing crypto"
action 1.8 cli command "do clear crypto session"
action 1.9 cli command "do clear crypto sa"
action 2.0 cli command "do clear crypto isakmp"
action 2.1 syslog msg "clearing route table"
action 2.2 cli command "do clear ip route *"
action 2.3 syslog msg "clearing NAT translations"
action 2.4 cli command "do clear ip nat translation *"
action 2.5 cli command "do clear ip nat translation forced"
action 2.6 syslog msg "enabling broadband tunnel0"
action 2.7 cli command "interface tunnel0"
action 2.8 cli command "no shutdown"
action 2.9 cli command "exit"
action 3.0 syslog msg "End of script. Broadband enabled."I've got an EHWIC-4G-LTE-V card in a 2921 router and am only able to connect via 1xRTT. Can someone take a look at the output below and provide some insight as to why I can't connect via LTE? Thank you.
BroadbandLabv233#sho cell 0/0/0 all
Hardware Information
====================
Modem Firmware Version = SWI9600M_03.05.10.06
Modem Firmware built = 2012/11/12 15:07:45
Hardware Version = 10
Integrated Circuit Card ID (ICCID) = 89148000001035643492
Mobile Station Identifier (MSID) : 9802145106
Electronic Serial Number (ESN) = 0x8028B8D1 [12802668753]
Preferred Roaming List (PRL) Version = 0
Profile Information
====================
Profile 1 = INACTIVE **
PDP Type = IPv4
Access Point Name (APN) =
Authentication = None
Username:
Password:
Profile 3 = ACTIVE*
PDP Type = IPv4
PDP address = 166.251.23.6
Access Point Name (APN) = SO01.VZWSTATIC
Authentication = None
Username:
Password:
Primary DNS address = 198.224.183.135
Secondary DNS address = 198.224.182.135
* - Default profile
** - LTE attach profile
Data Connection Information
===========================
Data Transmitted = 5428 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 3, Packet Session Status = ACTIVE
IP address = 166.251.23.6
Primary DNS address = 198.224.183.135
Secondary DNS address = 198.224.182.135
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Unknown
Network Information
===================
Current Service = Packet switched
Current System Identifier (SID) = 139
Current Network Identifier (NID) = 65535
Current Service Status = Normal
Packet switch domain(PS) state = Attached
Registration state = Registered
Radio Information
=================
1xRTT related info
Current RSSI = -77 dBm
Radio power mode = ON
LTE Technology Preference = AUTO
LTE Technology Selected = eHRPD(1xRTT)
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on 4G modems.
Modem Crashdump Information
===========================
Modem crashdump logging: off
BroadbandLabv233#sho run
Building configuration...
Current configuration : 10686 bytes
! Last configuration change at 19:39:23 UTC Wed Aug 20 2014 by @dm1n
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname BroadbandLabv233
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.153-3.M2.bin
boot-end-marker
logging buffered 4096 informational
logging console informational
no aaa new-model
ip flow-cache timeout active 1
ip domain name aaanet.com
ip cef
no ipv6 cef
multilink bundle-name authenticated
chat-script lte "" "AT!CALL1" TIMEOUT 20 "OK"
license boot module c2900 technology-package securityk9
license boot module c2900 technology-package datak9
redundancy
controller Cellular 0/0
track 100 ip sla 100 reachability
delay down 10 up 20
class-map type inspect match-any INSPECT-TO-ROUTER-CLASS
match access-group name INSPECT-TO-ROUTER-ACL
class-map type inspect match-any INSPECT-FROM-ROUTER-CLASS
match access-group name INSPECT-FROM-ROUTER-ACL
class-map type inspect match-any INSPECT-INSIDE-TO-OUTSIDE-CLASS
match protocol ftp
match protocol tcp
match protocol udp
match protocol icmp
class-map type inspect match-any PASS-TO-ROUTER-CLASS
match access-group name PASS-TO-ROUTER-ACL
class-map type inspect match-any PASS-FROM-ROUTER-CLASS
match access-group name PASS-FROM-ROUTER-ACL
policy-map type inspect INSIDE-TO-OUTSIDE-POLICY
class type inspect INSPECT-INSIDE-TO-OUTSIDE-CLASS
inspect
class class-default
drop log
policy-map type inspect TO-ROUTER-POLICY
class type inspect INSPECT-TO-ROUTER-CLASS
inspect
class type inspect PASS-TO-ROUTER-CLASS
pass
class class-default
drop log
policy-map type inspect FROM-ROUTER-POLICY
class type inspect INSPECT-FROM-ROUTER-CLASS
inspect
class type inspect PASS-FROM-ROUTER-CLASS
pass
class class-default
drop log
zone security INSIDE
description internal interfaces
zone security OUTSIDE
description external interfaces
zone-pair security INSIDE-TO-OUTSIDE source INSIDE destination OUTSIDE
service-policy type inspect INSIDE-TO-OUTSIDE-POLICY
zone-pair security FROM-ROUTER source self destination OUTSIDE
service-policy type inspect FROM-ROUTER-POLICY
zone-pair security TO-ROUTER source OUTSIDE destination self
service-policy type inspect TO-ROUTER-POLICY
crypto isakmp policy 1
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp policy 2
encr aes
authentication pre-share
group 5
crypto isakmp key <removed> address <removed>
crypto isakmp keepalive 10 periodic
crypto isakmp aggressive-mode disable
crypto ipsec transform-set HQ-vpn esp-3des esp-md5-hmac
mode tunnel
crypto map Branch-VPN-Policy 10 ipsec-isakmp
description VPN Tunnel to AAA-HQ
set peer <removed>
set transform-set HQ-vpn
match address Remote-HQ-acl
interface Loopback0
ip address <removed> 255.255.255.255
interface Tunnel0
bandwidth 512
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
ip tcp adjust-mss 1380
ip ospf cost 150
shutdown
tunnel source GigabitEthernet0/1
tunnel mode ipip
tunnel destination <removed>
interface Tunnel1
bandwidth 512
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
ip tcp adjust-mss 1380
ip ospf cost 150
tunnel source Cellular0/0/0
tunnel mode ipip
tunnel destination <removed>
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.10
description Data Network
encapsulation dot1Q 10
ip address <removed>
ip flow ingress
ip flow egress
ip nat inside
ip virtual-reassembly in
zone-member security INSIDE
interface GigabitEthernet0/0.20
description Voice Network
encapsulation dot1Q 20
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
interface GigabitEthernet0/0.40
description Management
encapsulation dot1Q 40
ip address <removed>
ip flow ingress
ip flow egress
zone-member security INSIDE
interface GigabitEthernet0/1
bandwidth 50000
ip address <removed>
no ip unreachables
ip flow ingress
ip flow egress
ip nat outside
no ip virtual-reassembly in
zone-member security OUTSIDE
shutdown
duplex auto
speed auto
pppoe enable group global
crypto map Branch-VPN-Policy
interface GigabitEthernet0/2
no ip address
duplex auto
speed auto
interface Cellular0/0/0
ip address negotiated
ip access-group NO-BOUNCE out
ip flow ingress
ip flow egress
ip nat outside
ip virtual-reassembly in
zone-member security OUTSIDE
encapsulation slip
ip tcp adjust-mss 1000
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
async mode interactive
crypto map Branch-VPN-Policy
router ospf 100
network <removed> area <removed>
network <removed> area <removed>
network <removed> area <removed>
ip local policy route-map sla-route
ip forward-protocol nd
no ip http server
no ip http secure-server
ip flow-export source Loopback0
ip flow-export destination <removed> 2055
ip nat inside source route-map Broadband-NAT interface GigabitEthernet0/1 overload
ip nat inside source route-map Cell-NAT interface Cellular0/0/0 overload
ip route 0.0.0.0 0.0.0.0 <removed> track 100
ip route <removed> track 100
ip route 0.0.0.0 0.0.0.0 Cellular0/0/0 10
ip route <removed> Cellular0/0/0 10
ip route <removed> Tunnel0
ip route <removed> Tunnel1
ip access-list extended INSPECT-FROM-ROUTER-ACL
permit udp any any eq isakmp
permit icmp any any
permit udp <removed> any eq syslog
ip access-list extended INSPECT-TO-ROUTER-ACL
permit icmp any any echo
ip access-list extended NAT
permit ip <removed> any
ip access-list extended NO-BOUNCE
permit ip host <removed> any
deny ip any any log
ip access-list extended PASS-FROM-ROUTER-ACL
permit udp any eq bootpc any eq bootps
permit esp any any
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended PASS-TO-ROUTER-ACL
permit udp any eq bootps any eq bootpc
permit esp any any
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended Remote-HQ-acl
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
permit ip host <removed> host <removed>
ip access-list extended sla-packets
permit ip host <removed> host 8.8.8.8
ip sla auto discovery
ip sla 100
icmp-echo 8.8.8.8 source-interface GigabitEthernet0/1
frequency 10
ip sla schedule 100 life forever start-time now
logging source-interface Loopback0
dialer-list 1 protocol ip list 1
route-map Broadband-NAT permit 10
match ip address NAT
match interface GigabitEthernet0/1
route-map sla-route permit 10
match ip address sla-packets
set ip next-hop <removed>
set interface Null0
route-map Cell-NAT permit 10
match ip address NAT
match interface Cellular0/0/0
snmp-server enable traps vstack operation
access-list 1 permit <removed>
control-plane
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 0/0/0
script dialer lte
modem InOut
no exec
speed 144000
line vty 0 4
login local
transport input all
scheduler allocate 20000 1000
ntp update-calendar
ntp server 10.10.32.179
ntp server 10.10.32.180
event manager session cli username "<removed>"
event manager applet Primary_INET_Down
event track 100 state down maxrun 90
action 1.0 syslog msg "Ping has failed, Primary circuit unable to reach internet!"
action 1.1 cli command "enable"
action 1.2 cli command "configure terminal"
action 1.3 syslog msg "shutting broadband tunnel0"
action 1.4 cli command "interface tunnel 0"
action 1.5 cli command "shutdown"
action 1.6 syslog msg "Clearing crypto"
action 1.7 cli command "do clear crypto session"
action 1.8 cli command "do clear crypto sa"
action 1.9 cli command "do clear crypto isakmp"
action 2.0 syslog msg "clearing route table"
action 2.1 cli command "do clear ip route *"
action 2.2 syslog msg "clearing NAT translations"
action 2.3 cli command "do clear ip nat translation *"
action 2.4 cli command "do clear ip nat translation forced"
action 2.5 syslog msg "enabling 4G card and tunnel1"
action 2.6 cli command "interface cellular 0/0/0"
action 2.7 cli command "no shutdown"
action 2.8 cli command "interface tunnel1"
action 2.9 cli command "no shutdown"
action 3.1 syslog msg "End of script. 4G enabled!"
event manager applet Primary_INET_Recovered
event track 100 state up maxrun 90
action 1.0 syslog msg "Broadband ping has recovered, shutting down 4G card and tunnel1 to limit data usage!"
action 1.1 cli command "enable"
action 1.2 cli command "configure terminal"
action 1.3 cli command "interface cellular 0/0/0"
action 1.4 cli command "shutdown"
action 1.5 cli command "interface tunnel 1"
action 1.6 cli command "shutdown"
action 1.7 syslog msg "clearing crypto"
action 1.8 cli command "do clear crypto session"
action 1.9 cli command "do clear crypto sa"
action 2.0 cli command "do clear crypto isakmp"
action 2.1 syslog msg "clearing route table"
action 2.2 cli command "do clear ip route *"
action 2.3 syslog msg "clearing NAT translations"
action 2.4 cli command "do clear ip nat translation *"
action 2.5 cli command "do clear ip nat translation forced"
action 2.6 syslog msg "enabling broadband tunnel0"
action 2.7 cli command "interface tunnel0"
action 2.8 cli command "no shutdown"
action 2.9 cli command "exit"
action 3.0 syslog msg "End of script. Broadband enabled." -
Accessing Server when only connected via Internet Sharing
Currently, I don't have the ability to directly connect my Mac Pro which I use as a Server to the router as I have no direct access to it via cable and it does not have an Airport card.
However, I can access the internet on it if I use internet sharing on my iMac which is connected via Gigabit Ethernet to the Mac Pro at all times.
In order to use any of the services such as Time Machine from another machine, I always need to connect it directly by cable. This leaves me wondering if there is a way to tunnel the Mac Pro through the iMac so it is accessible via Wifi? Is there a setting on either Machine I have to activate / set to make this work?
It is only thought to be a temporary solution until I move to a new flat where it will be directly connected to an Airport Extreme.
Thanks for your help!Seems that the issue is something to do with connecting via WPA2. When I set Internet Sharing to use WEP (by option-clicking the security menu), I'm then able to see the network shares and the printer.
-
Jetpack 5510l has no wifi signal - can only connect via usb to get Internet.
Bought this device on a Thursday and it worked flawlessly - until Saturday. The device has had a consistent connection to Verizon, but on Saturday the wifi began to 'go out.' The device showed everything was working, but the wifi radio seems to have just turned off (after intermittently failing for a period of a couple hours). We tried several different devices, none showed a working wifi signal coming from the mifi by the end of the day.
What we have done so far:
Rebooted.
Removed battery (after shutting down), restarted.
Used hard-reset button.
Used web intefrace to turn wifi on and off - and on, changed ssid, passphrase, reset again (after each phase we also gave it an hour to see if the signal would return).
Nothing has gotten the wifi from the device back online - it's as if either the radio or wifi antenna is completely broken. We attempt to connect using 3 or 4 different devices - so it is most certainly the mifi. There are no errors from the device - is there a debug / test mode?
Our current workaround is to connect via usb to a Macbook and just share the internet connection - which works great, but makes travel a bit more difficult if a computer has to be connected to allow us to have a wifi signal (not from the mifi).
Regards.Taking the Jetpack apart is going to void your warranty. I would not suggest going down that road until your warranty is up. Instead give VZW a call and have them ship you a replacement under the warranty service agreement. You have done a perfect job of isolating the problem to a wifi radio issue. Its easy to recreate and confirm which will make the phone call fairly quick. Unless you got sold on some kind of Best Buy warranty and prefer to go through them, VZW is going to be your best bet at getting a speedy replacement.
-
MDD can't recognize drive connected via PCI card
Hello there,
I tried connecting a new Maxtor ATA100 drive to my MDD via a Sonnet TEMPO ATA100 PCI card. Everything works OK except that the drive doesn't mount. Disk Utility doesn't "see" it and get this, ... when I tried opening System Profiler to see if the PCI card was recognized, the following was displayed at the bottom of the About This Mac window: Opening border_right.gif. Preview then launched and opened such gif image!
I used the ribbon cable that came with the drive and its jumper was set to Cable Select. I could connect the drive to the on-board ATA66 bus but I would like to solve this issue and make it work. Any thoughts?
Thanks again,
JacoboRodney,
Thanks again for your reply. Believe or not the problem was a loose power connection! The card was recognized and the drive mounted. However, the PCI card only recognized 128 GB (of the 500). Must have been an old one, so it came out.
Thanks again,
Jacobo -
Acer Aspire One will only connect via Fon now on H...
Since activating Fon on my BT Home Hub my Acer Aspire One - running Linux Linpus - will no longer log on to the 'normal' wireless connection on my hub, only Fon, which has limited bandwidth, etc.
Anybody know why? Have a solution?
I've 'proved' it's the Fon activation my doing a full reset on the hub. My One connected normally until Fon was reactivated, then back to Fon connection onlyRe WPA - it was fine until Fon was activated!
When I did a factory reset on the hub the One connected as normal - until Fon reactivated at which point it was back to via Fon only!
As the MAC address for FON and your normal SSID would be the same, perhaps it is seeing your normal SSID and assuming that is FON, and connecting to that in preference to your normal one.
Really strange problem.......
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
CK-7W and 6230i only connects via bluetooth
I have installed the carkit ck-7w and the phoneholder MBC-15S, but the only way my phone will connect to the carkit is via the bluetooth. When I put the phone in the holder (MBC-15S and the datacable)it starts charging but doesn't route the microphone or speaker to the carkit. The symbol that indicates a connection to the carkit (the symbol of a little car) does not appear. I have tried to replace the headunit of the carkit and the datacable, but without success. I also assume that the holder (MBC-15S) is not the problem because the problem is still there when the datacable is connected directly into the 6230i. Replacing the phone with an identical 6230i itself doesn't resolve anything, so I assume the 6230i isn't the source of the problem.
Does anyone know a solution to this problem?
Have anyone experienced a similar scenario?
Could it be a software issue regarding the 6230i?Hi! Just wanted to share the solution to my previously described problem.
It turned out that the CK-7W carkit wouldn't work properly as a result of an extension CAT-5 cable. During the installation ut turned out that the cable that runs from the phoneholder (MBC-15S) to the CK-7W was too short, so I decided to use an extension cable. The extension cable was an ordinary CAT-5 cable with 8P8C plugs in both ends, approximatly 50 cm long, connected to a free standing socket witch allows a 8P8C plug to inserted in both ends, making it possible to plug the male ends from the original datacable to the aftermarket CAT-5 plug(8P8C plug) together.
I removed the CAT-5 cable and used only the original datacable and the problem was solved.
I tested the CAT-5 cable and the free standing socket in a computer and everyting worked fine. So I guess there was nothing wrong with my aftermarket cable equipment. -
Can you use time capsule if you only connect via wi fi, and no ethernet lines?
I'm considering buying a Time Capsule to back up my stuff and use as a router, but I only use wi fi (my fi) via my phone service. Is Time Capsule functional without an ethernet connection, and if so, how functional? Basically, is it the right thing for me within these parameters?
thanks in advance
TaythorneThis could be OK, because Time Capsule's operation is quite independent of the router function. Time Capsule does need to live on a LAN with a router somewhere, even if it is not the router itself. As long as that's true, it could work.
But it sounds like there is more research you have to do. Normally, Time Capsule either functions as a router, meaning you give it a direct IP address to a modem; or it functions in bridge mode, meaning you give it the IP address of a router. I don't know how a mi-fi works compared to a cable or DSL modem, but I am guessing you might set up the Time Capsule to connect to it in bridge mode. If that works, everything else should work fine.
Regardless of the setup, Time Capsule should work as long as the Mac can find the Time Capsule and mount the backup volume. An actual Internet connection is not required for that, because it's all within the LAN. -
Why can I only connect to the internet using my IPhone 5S 4G via a USB and not wirelessly?
Apologies if I'm not using the right jargon ... I have a laptop (Dell Latitude D510 - Windows 7 Ultimate) that can connect to my Mobile Broadband wirelessly no problem but I can't utilise my IPhone's 4G connection (iOS 7.0.5) unless I use the USB cable (my personal hotspot is also on). I can't connect wirelessly to my personal hotspot without the USB cable. It keeps saying Windows is unable to connect to my IPhone. I have tried to troubleshoot this myself but can't find an obvious problem. Interestingly I could only connect via my USB when I downloaded the ITunes program as my computer failed to recognise my IPhone. Furthermore, I have a Dell Alienware laptop which has no problems connecting to my IPhone either way - USB or wirelessly (also has ITunes downloaded). I've searched the Internet forums for an answer on but I can't find one. Can anyone help? Thanks if you can.
Personal Hotspot requires a password:
http://support.apple.com/kb/HT4517 -
Ethernet-only connection to Netgear MR814v3
Qwest DSL (Actiontec GT701 Modem) with 2 Macs: 1 iBook and 1 Powerbook G4, both running OS 10.3.9
Netgear MR814v3 wireless router
WPA security
I connect fine wirelessly with iBook, but for the Powerbook, I can only browse/get online successfully thru ethernet. Airport has strong signal and I enter password for the SSID/network - and everything "looks" great (i.e. in the Network Prefs it says I am connected to the Internet, but really I can't do anything).
Any advice would be appreciated.So, the Powerbook was connected to the router via ethernet, then all of a sudden, the iBook would not connect wirelessly (like it had been all day long) and went so far as to give an error message that the (WPA Personal) password for the network was wrong. I rebooted the modem, router, and both laptops, in that order (waiting for all appropriate lights to come on) and now, they have switched places. The Powerbook connects using wireless and the iBook will only connect via ethernet.
Additional note: I had to type in the DNS servers (provided by my ISP, Qwest) before getting the iBook to connect via ethernet.
I am officially frustrated.
One more thing - of course, Qwest wanted me to buy their pricey, high-end "modem and wireless router-all-in-one) but I already had the Netgear from my last setup and wanted to save some cash (needed to, really) so I got the barebones Qwest modem.
Thanks in advance for any more help!
MK -
Financial Reports Client - 11.1.2.1 - Won't connect via VPN only?
When I try and connect via VPN only. I get: You are not authorized to use this functionality. Contact your administrator.
Here's the log from client. We have ensured the client version matches the server version exactly. Funny as when I'm directly on their network I can connect just fine. Hoping this log will point to solution.
Log:
[2012-06-01T10:31:45.196-04:00] [EPMFR] [ERROR] [] [oracle.EPMFR.core] [tid: main] [ecid: 0000JUcTOpZD4io5KVt1ie1FmD9H000000,0] [SRC_CLASS: com.hyperion.reporting.registry.FRSystem] [SRC_METHOD: lookupHsServer] [[
com.hyperion.reporting.util.HyperionReportException: Could not connect to the server.
Please make sure that the server is running as specified in the logon dialog (including port number if not default).
at com.hyperion.reporting.registry.FRSystem.lookupHsServer(Unknown Source)
at com.hyperion.reporting.javacom.HsServer.getServer(Unknown Source)
at com.hyperion.reporting.javacom.HsHelper.getServer(Unknown Source)
[2012-06-01T10:31:45.273-04:00] [EPMFR] [ERROR] [] [oracle.EPMFR.core] [tid: main] [ecid: 0000JUcTOpZD4io5KVt1ie1FmD9H000000,0] [SRC_CLASS: com.hyperion.reporting.javacom.HsServer] [SRC_METHOD: getServer] [[
java.lang.NullPointerException
at com.hyperion.reporting.javacom.HsServer.getServer(Unknown Source)
at com.hyperion.reporting.javacom.HsHelper.getServer(Unknown Source)
]]I think you have already posted this problem on another post, I said it is possible it could be a ports issue.
Have a look at the following http://www.oracle.com/technetwork/middleware/bi-foundation/epm-component-communications-11121-354680.xls
Select FR studio as the client and it should give indication to the ports that need to be opened.
Cheers
John
http://john-goodwin.blogspot.com/ -
wi-fi is gray will not connect since ios7.03, worked fine before this version...now slow, very slow, using nothing but 4g, no wi-fi no solution from apple store but to purchase a new Iphone....other 4s phone purchased at same time connects via wi-fi what gives?
Also reloaded per Apple instructions via web, Apple stores only solution "purchase a new phone", no attempt to fix problem.https://discussions.apple.com/thread/5554599?tstart=0
-
K7n2 delta, won't allow me to connect to the internet via pci modem
motherboard: K7n2 delta, nforce2 ultra
won't allow me to connect to the internet via pci modem
i have got 2 computers with same mobo, can connnect through external 56k
but the 2 internal 56ks (one in each computer), will not connect.
just dials then beeps, or no dialing tone.
the 2 internal ones are differnet makes, but connect through PCI
there must be something wrong with Mobo settings or pci stuff
all internet and modem settings are correct, etc etc etc
can u help
or does anyone have a pci 56k running on that mobo?Quote
Originally posted by Solway
i made my creative one work and dial, using pulse dialing, but it takes ages
but my other one has no dialing tone, its werid.
If your not hearing dial tone you might have your phone plugged into the wrong port. Most modems have 2 outlets, one is labeled line ( that is the one you should have plugged into the jack (RJ11C). If that's correct, query the modem and see if it tests OK, you may have a defective modem. -
How do I use time capsule as a direct backup drive only connect to my macbook pro via ethernet cable
I have recently abandoned my cable internet service provider and am using my iPad as a hotspot via verizon wireless service. I am trying to reconfigure my time capsule as a back up drive only connected by an ethernet cable.
I was able to set it up on my new hotspot wireless net, but do not want to use it that way because of the data usage impact on my verizon wireless account.
Hopefully there is an easy answer, but it is not intuitively obvious to me.Well I have to say you can do it.. but if you are plugging and unplugging ethernet, you could just as easily plug and unplug an external USB drive.. and it will be faster and more reliable than the TC.
I explained how to do the TC as a secondary network in the posts here. Look down the bottom of the discussion.
https://discussions.apple.com/thread/4817218?tstart=30
If any of that doesn't make sense just post again here..
You can also do it with wireless if you accept using a USB wireless stick plugged into the Mac.. then you have two wireless clients and can connect simultaneously to two different networks.. using the same principles as above that you remove the gateway and dns problems that arise by manual settings.
Maybe you are looking for
-
I need to provide the output for one 3750x switch out of a cluster of 7. With all of the various stats, the entire log will be fairly large.
-
Need to update custom fields in MSEG table using "BAPI_GOODSMVT_CREATE"
Hi All, There is a requirement to update custom fields in table MSEG which are part of append structure. There is a option to update the custom fields using the one of the tables parameters "EXTENSIONIN". Anyone please advice how can I update the cus
-
Where can i download an older version of itunes?
Am not impressed with the new itunes version taking away the ability to back-up music library to disc (backing up whole library that is, not just playlists) and so i am looking for somewhere i can download the older version 10.1.1 from. Ideas anyone
-
Keyword search in multiple folders
May be a stupid question..... We want to have all of our photos stored on one server and then access them remotely and be able to do a keyword search to locate them later. We did a test with several folders but when we do a keyword search we have to
-
IO6 upgrade app difficulties - Germany vs. US update location
I bought my Ipad in the US but installed the IO6 software while living at my current home in Germany. Now when I go to the app store to download updates to the apps I get a german message saying something to the effect that I can't download the apps