T60 does not boot with Intel T7600G CPU

I replaced my Intel Core Duo T2400 with Intel Core 2 Duo T7600G CPU in ThinkPad T60(1951-CTO) laptop. However, laptop does not boot with Intel Core 2 Duo T7600G CPU. It doesn't even complete the POST: https://db.tt/8UL8FlE0 As seen in the video, I plugged in the power adapter at 0:02 and pressed the power button at 0:06. One can hear a little click made by optical device. If I press the power button again at 0:16, this click does not happen. BIOS version is 2.27. I have reset the BIOS settings by disconnecting the CMOS battery, but this didn't help. Once I replace the T7600G with my old T2400 then I'm able to boot the laptop.
Any ideas what might cause such behavior? Shouldn't there be beep codes in case of CPU issues? What else to try?

TuuS wrote:
600X wrote:
Since you came from a T2400, does your T60 even have a Rev. 3 motherboard? If it does not, then no Core 2 Duo will work, only Core Duo's.
I don't claim to be the top authority on T60 motherboards, but I believe any will use a Core 2 T7600, 7400, 7200 if the firmware is updated.
My own experience mirrors what TuuS has stated. I have yet to see a T60/p from any walk of life with a recent BIOS that will bark at a proper Core 2 Duo CPU.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

K9AGM3-F does not boot with PCIe 4x device in PCIe 16x slot

K9AGM3-F motherboard does not boot with PCIe 4x Intel PRO/1000 PT dual port network interface card installed into PCIe 16x slot on motherboard. The boot process stops in BIOS screens. The motherboard works flawlessly without this NIC. K9VGM-V + Intel PRO/1000 PT boot successfully. I tried three K9AGM3-F motherboards and two Intel PRO/1000 PT NICs in different combinations, the results are always the same. It appears to be some kind of BIOS problem.

Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
Minor point, probably irrelevant: I said you install the driver f i r s t. Then you put the physical card in.
The driver is completely irrelevant because the driver is a part of operating system, but as I already wrote before the boot process stops long before the OS start.
Quote from: Fredrik Åsenius on 09-April-08, 22:52:27
No stability issues otherwise?
PSU is always good to know.
The PSU is irrelevant too because the same NICs work in the PCIe 1x slot of the same motherboard with the same PSU.

Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard

I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.

Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue.

Solaris 8 does not boot in Intel Platform

I got free Solaris 8 CD for Intel Platform. I installed it in a PC with Intel 133 cpu. It cannot boot up after it is installed. When I boot, it just keeps rebooting system and get an error says, "File Can not be synchronized". I know I made some mistake during installation. My PC has a 3COM network car but it is not connect to any network. During installation, I told that I connect to network and give a non-exist ip address.
My question is how do I reinstall it? I have tried to delete everything in hard drive but no luck to get installation start again.
The other problem I see is that the scan program tells me that there is an IDE card lack of resources and conflicts with another IDE card.
Could some one tell me how to make Solaris 8 working on my Intel Platform PC?
Thanks,
Cindy

I'm trying to install Solaris 8 using the Device Configuration Assistant diskette in order to boot from the CD Drive. The whole boot process goes through as described in the documentation but at the time that is trying to copy files to the HD in order to porceed with the install, I get the following error message:
<pre>
No Disks that meet the citeria in the Solaris
installer documentation found.
Please check the system or try another installation option
</pre>
When the software is checking for drivers/hardware, it recognizes the HD, but it seems that when trying to boot it doesn't. The documentation makes reference to fdisk and partitioning but I am not given the oportunity to do it at any time.
Any help would be greatly appreciated.

2960X-48FPS-L does not boot with IOS 15.2-2E

Hello,
i got a bunch of 2960X switches. But some of them do not boot with the new IOS Version. The older 15.0-2 EX do boot.
Does anybody have a clue why this happens? During the Bootprocess it just stops to load:
File "flash:/c2960x-universalk9-mz.152-2.E.bin" uncompressed and installed, entry poin0x3000
executing...
Loading "flash:/c2960x-universalk9-m
Thank you for your help.

On the ones that cannot boot 15.2(2)E, can you break the boot cycle using the "Mode" button?
If the answer is "yes", then try the following:
1. Copy the IOS BIN file from a working switch to a USB flash drive;
2. In ROMmon, force the switch to boot the IOS from your USB flash drive;
3. If it does not work, try a different IOS, like the EX3 for instance. Try the same process, boot the BIN from your USB flash drive.
4. If it works, try a different IOS, like EX3, for instance. Downgrade the IOS from 15.2(2)E to EX3 and see if the switch can boot normally.
This exercise will determine where the fault is coming from: IOS bug or a hardware batch problem.
To determine if you'e got a hardware batch problem, you may need to look at the serial number of the switches working and not working. From left to right, look at the 4th, 5th, 6th and 7th numerals. This will determine the year and month your appliances were made.

P7N2 diamond does not boot with q9450

I cannot get my new P7N2 diamond to boot, i am using
q9450 cpu
2x2gb corsair xms 3 dhx (dual channel in blue slots)
BFG 9800 GTX
2X 500 Maxtor sata 2 HD
2xIDE liteon lightscribe DVDR
600 watt noisetaker enermax power supply
It turns on but there is no bios beep.Can hear the noise of the drives spinning up, powering up everything, lights on motherboard are lit and fans spin, but the monitor is not showing any bios reading. I have tried running one stick of ram, resetting cmos, check all cables and plugs, but it just wont post. Could the bios be too early to recognise the intel q9450, otherwise any help would be appreciated.

Quote from: jjdaly on 18-July-08, 19:56:21
Wow. You either build lots of systems, or your expectations are pretty low. 'A fact of system building' should only apply to large OEMs not the home builder doing a like a build a year. That would be a pretty high rate of failure that any manufacturer should be embarrassed by.
I'm curious as an employee of Intel how many folks have had issues with Intel branded boards? I know that we tend to build systems that are less enthusiast-friendly than other manufacturers, but if it's enthusiast-friendly and doesn't work what good is it?
I have built loads of systems and I still do. I've had my share of doa hardware. It's not an everyday occurance but it happens. A build a year? I've built 8 so far this year and of those I've had one no post mobo (XFX 790i), a bad ram kit, 1 vid card with memory artifacting, a Q9550 (oem) that died a sudden death during testing, and a failed psu. That last item was my fault for skimping. I just know it happens and I don't waste time stressing about it, I rma and get on with it. I like happy endings so I don't sit in the problem, I resolve it. How many folks have had issues with intel branded boards? I'm not sure where you're going with this but I'm guessing intel's numbers aren't much different than MSI's or anyone else's when it comes to percentages. Like any other manufacturing process, it's a given that there will be faulty parts shipped.

P67A-GD65 does not boot with LSI 9240-8i HBA

Hi All,
When I installed my LSI 9240-8i I was able to boot to the ICH10 Raid as long as the Marvell Raid controller was disabled. Once I updated the LSI card to the latest version of the firmware I cant boot at all. I've cleared the CMOS, I've disabled everything in the BIOS (raid controllers, 1394, NIC, etc). All not no avail.
Thus Far I've tried:
-Booting to OS on the ICH10 RAID gets me into Windows 7 (x64): Resulted in the LSI controller showing, "This device could not start. (Code 10)" under Device Manager.
-Updating Firmware: Resulted in the mobo hanging on POST at code "92".
-Upating BIOS from 1.B to 1.C5 Beta: Resulted in mobo hanging on POST at code "92".
-When I move the card to my Dell Prescision workstation, the LSI RAID controller works like a charm!
Observations:
MSI P67A-GD65 BIOS v. 1.B
-LSI Firmware
20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN
(Same as above, but I list it anyways)
MSI P67A-GD65 BIOS v. 1.C5
-LSI Firmware
20.10.1-0037 (APP-2.120.54-1235)   15-APR-11   - BROKEN
20.10.1-0029 (APP-2.120.24-1181)   - 04-MAR-11 - BROKEN
MSI PLEASE HELP!
I am running:
Mobo: MSI P67A-GD65 1.C5
CPU: I7 2600k
RAID: LSI 9240-8i
Thanks!

Quote from: NovJoe on 23-May-11, 10:16:19
Looks to me that it is the LSI firmware issue as the card works fine until you updated its firmware.
Do card with the card's vendor.
Hi NovJoe,
Thats just it. It looks like its an MSI BIOS compatability issue all along. Before I upgrade the firmware, the card works in my Dell Precision Workstation, but does not work on the MSI mobo; shows Device could not start (Code 10) error. After I upgrade the Firmware, the MSI mobo will not POST, but the Dell still boots up with the card perfectly.
Its definitely NOT the card. If both the 9240 and 9260 cards work perfectly in other computers then there is something wrong with the MSI mobo or BIOS.
Please help.
Thanks!

Securing old 10.4 xserve with hot spare - new xserve does not boot with 10.

dear you,
I am in the murky situation of having to secure a single, non redundant productive scenario which is running on one xserve (model identifier 1,1; dual core 3GHz; boot-rom XS11.0080.B00). due to several reasons the server needs to be cloned, so that a separate xserve with a daily cloned boot-device can take over if things go south with the productive one.
unfortunately the newly bought xserve quadcore single 2.26GHz refuses to boot from the image taken from the production machine. tried to downgrade firmware, did not help. new machine crashes during startup (empty grey screen).
anybody knows any help? moving the production machine to 10.5 or newer is NO option.
an option could be two elder xserves I have here additionally. how do I find out which xserve model will boot with an image from the production server?
thank you all for any idea in advance,
thaijay
Message was edited by: thaijay
Sorry, failed to let you know the productive server is running 10.4.11. please let me know which other details I can post/will help us with this issue

This is never going to work via cloning.
The server you're cloning has to be one of the original Intel-based XServes. Each successive revision adds requirements to the OS to the point where they have a minimum OS version. In the case of the latest generation servers, they won't run on anything earlier than 10.5.6 (IIRC). To put it simply - 10.4 doesn't know how to drive the latest generation hardware.
In any case, cloning is rarely a good idea for servers anyway. You would do better to look at the services you're running and look at backup/failover plans for them rather than trying to clone the entire server. Many services such as Open Directory, DNS, MySQL and more have built-in replication systems that are designed to replicate their data across many machines. Other client-facing services such as AFP, web, FTP, etc. can be set to failover (where the second machine takes over the service when the primary machine fails).
Such replication/failover techniques are far more reliable than a daily clone, and they're also faster. Replicated data could be maintained up to the minute, compared to a day old data if you need to boot up the clone.
If you really, really want to go the clone route, then reverse the roles - setup the new machine as the primary server with all the services and clone this machine to create your failover system. 10.5.6 will run the old/original XServe, it's just a matter of updating your services to the newer version.

24" iMac AlSiO does not boot with iPod video on USB dock

Hello all,
I have already reported this as an issue with Apple.
I noticed that when I turn on my new iMac with the video iPod on the dock connected via USB, I only see the gray screen and the OS does not start. However, once I remove the iPod from the dock, then the Apple logo will show up, and the circular moving tiny line counters will ensue before the login screen appears.
Just wondering if anyone else is running into this problem.

Thanks for the suggestions den.thed and elmac.
I have done the following:
- Selected the Mac OS X on the MacHD as the startup disk and locked that from further changes. Restarting the iMac did not work.
- Verified and repaired permissions. Restarted the iMac and it did not work either.
In addition, I also tried:
- Restoring the video iPod and leaving it without contents. Rebooting the iMac worked.
- Syncing iTunes with the iPod after the restore. The rebooting problem appears again.
It seems like some synced items on the iPod are causing the issue as odd as that sounds.
I did not have this problem with my G5 iMac.
Since there is a workaround, I'll just live with that for now.
Thanks again.

WRT300N Router does not working with Intel 4965AGN adapter on Wireless-N

Hi! I have recently bought the laptop Acer 5920G with Intel 4965AGN network adapter and Windows Vista. I have read that WRT300N Router is supporting Draft-N standard, so I purchased it. The router is working fine on Wireless-G 54Mbps (firmware - 2.00.17), but not on Wireless-N. I tried to enter the following settings: ssid - any non-linksys name; radio band - wide; n-channel - 9; standard channel - 11; beacon interval - 50; Fragmentation threshold - 2306; RTS threshold - 2307, but nothing has happened, connection still remains 54Mbps. How should I configure the router and network adapter to get Wireless-N?

okay... try reflashing/upgrading the firmware on the router, after reflashing the firmware on the router, reset it back to default settings and reconfigure it according to ISP settings...edit the wireless settings again, make sure that "wireless mode" should be mixed...
on the vista computer, click on start >> control panel >> network & sharing center >> manage wireless network and try removing existing wireless networks from profile and manually add wireless n/w profile according to wireless settings of the router...check whether it makes any difference or not and let me know.

PC does not boot with Ipod Nano

My configuration:
Shuttle SK83G, Athlon64 3000, Windows XP Pro, Logitech DiNovo wireless desktop.
My problem:
If my Ipod Nano is connected the PC will not boot. The bios screen shows up and then nothing happens. I even can not access the bios. If I remove the ipod the PC will eventually start windows. But in absolute slow motion (I can see how the Windows startup screen fades in step by step).
If I connect my Nano after booting, everything is perfectly fine. Also with my Ipod Mini connected, the PC boots up without a problem.

it's not just a Nano problem, but a USB port problem
That's correct. USB is famous for this. Something in the BIOS (probably) is telling it to try and boot from the nano, but of course it can't find a valid OS there. And the solution is just what you suggested. Don't boot with the nano connected.

P35 Neo ram problems. Does not boot with 4 sticks

Greetings!
This thread is little related to: https://forum-en.msi.com/index.php?topic=110095.0
Okey so I bought this rig last friday(will post specs later). 4x 1gb ram sticks, shows up as 3.3gb. Was gona install 64-bit Vista today, but got some problems.
I left my computer on during night just to check if it runs fine. I wake up around 6am, turn power on to my monitor. Screensaver, move mouse, desktop and BOOM: Bluescreen(something about memory). Ok so I shutdown my comp, try to reboot got no signal. Removed 2 ram sticks(A2,B2) and yey it works. I plug them back in and again nothing. I test them 1 by 1 on both of the free slots, no problems detected.
Why won't my P35 Neo boot with 4 gigs of ram? And why did it work for 2days? :P
My guess is that the bios is still not ready yet(using 1.2v).
Specs: OCZ 700W GameXStream, P35 Neo-FI, C2D E6750, 4X PQI 1024Mb DDR800Mhz, Leadtek 8800 Gtx

Quote from: NovJoe on 07-August-07, 10:18:34
If I understand correctly, you are saying that you can install Vista and XP to the system but not able to boot into the OS'es when you have 4GB of RAMs installed?
I would recommend you to test the RAMs with Memtest86.
Yes, I could install Vista and XP just fine. Also at first I could boot them with 4gigs just fine. Now my system won't POST with 4 gigs.
I've tested each one of the ram sticks and they are error free.

HPE-510t does not boot with AMD FirePro W5000 (Windows 8.1)

I just purchased an AMD FirePro W5000 (TDP = 75 W) to replace my nVidia Quadro 600 (TDP = 40 W) in my 2011 HPE-510t (i7-2600, 12 GB RAM). Dell U2913WM monitor.
My machine will not start with the new card inserted. I upgraded the stock 300 W power supply to a 450 W Antec VP450F, but that didn't change the startup situation. I tried DisplayPort and Dual-Link DVI-D.
Anyone been able to get the AMD FirePro working in an HP desktop of this generation?
Thanks,
Mike
This question was solved.
View Solution.

Hi Mike,
I am glad that you finally have success. The issue is probably that the PC BIOS level is too low.
The passmark numbers look very good.
BTW -- I had the ASUS P8P67 motherboard and donated it another forum member. It wouldn't support an EVGA UEFI BIOS based graphics card. I ended up replacing the ASUS P8P67 with the ASUS Z87.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

T60 does not boot up from sleep mode

Hi,
My client has a T60 with an advanced docking station. When he leaves the office he undocks and puts it into his bag and goes home. The laptop is set to sleep when the lid is closed. When he returns the following day, it has switched off and when he redocks and switches it on, it says it is resuming then goes blank. It is on, hard drive light flickering etc but he cannot work on it. We have to hard reset and then halts at the safe mode options, I choose "start Windows normally" and it boots up fine. It's running Win7 Professional. Please advise if there is any software that can undock gracefully or any other suggestions would be appreciated...thanks,

he needs to switch off the laptop and then undock, otherwise the machine would think he is still in docked mode.
Or he needs to eject the machine out of the docking station (by pressing the no. 1 eject button on the dock), put to sleep and then undock.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

10.7.3 does not boot with 10.7 USB

Hi all,
it seems I am in trouble. Clear Crystal killed my 10.7.3 Macbook Air and i need to reinstall Lion. Unfortunately my flash drive with 10.7 installer from App store is not working anymore. There was no change on the flash drive and worked. Does any has the same experience ?
Now I have to wait 10 hours to download installer again from recovery partition
Mag

OK, so its true. I just tried the same USB flash drive with 10.7. from App store and its able to boot from it on my Macbook Pro with 10.7.2, but not on Macbook Air 10.7.3
Mag

T60 does not boot with Intel T7600G CPU

Similar Messages

Maybe you are looking for