T60 Sata 2 Hard Drive

Hi all
I know this topic is in forums alot but i just wanted to confirm,
Will the T60 handle a Sata II hard drive in either the primary or ultrabay slots? I mean will it work at all, even if its slow.
Thanks
Alex
Solved!
Go to Solution.

Sorry I am still not getting it If the ulra bay is Pata, will it work with a sata drive through a bay adaptor?
I would love to go ssd but its a bit expensive for me...mores the pity.
i am asking about sata 2 because i would rather buy a new sata 2 hard drive than a new sata 1 drive i wanted to know if it will be picked up in either bay.
Still not too sure sorry about my ignorance and thanks for your answers

Similar Messages

Need help in installing a SATA hard drive with 865pe NEO2

Hello there
I need a help in installing a Sata hard drive ,it is WD 250 GB , my motherboard is 865PE Noe2 , the bios is the latest one
already I got another old hard drive ,not a Sata ,a regular IDE one installed as a master hard drive
I want to install the sata hd as a slave for the IDE hd for now to transfer the files and documents
I already physically installed the Sata hard drive yet the problem is that it was listed in the bios , I followed some of the steps here in the forum mentioned but all what I got is I found it listed as the fourth IDE master , not as the primary IDE slave
in Windows Xp Sp2 it is not listed of course in the windows explorer , but it is there in the device manager
look I am very confused and I tried most of the combinations in the ide configuration in BIOS
what should I do coz I am feeling so bad and stupid ,you can consider me a n00b in this hard drive thing

1st the sata drive cannot be listed as a slave drive to the ide master [key word=ide-can be configured as master OR slave, master IF only 1 hd, master and slave IF 2 hds], on the sata controler you can have master and slave, the ide cable has two connectors for the hds, sata has only 1 hd connector.
are you wanting to install the sata as primary master and move the operating sys to that drive, if so you will need an IMAGING software to move an operating system OR you could do a fresh operating system install to the sata drive then install your programs.

Seagate 300gig sata hard drive not recognized

I'm trying to install a seagate 300gb sata hard drive in my dual 2.0 g5.
I can plug in the two cables and the drive fits in fine, it even spins, however the computer does not recognize that the drive is there.
I've checked the sata in the system profile and tried disk utility but it is simply not there. Could this be a wiring problem or a bad drive? How do I check this?

My guess is that it is a Seagate 7200.9 with SSC on. If that is the case you will need a PC and this tool:
http://www.seagate.com/support/kb/disc/faq/ssc.html

HT5634 How to put windows 8 on MacBook Pro via sata hard drive USB off of other computer

Hi I have recently purchased a MacBook Pro 15 retina. My old laptop was windows 8 but the motherboard crashed and I have the sata hard drive that has all of my data info including OS would I be able to use the OS on Boot camp without purchasing a new license? Also how would I do that? I have put the hard drive into a portable USB device so I can access it via USB 3.0.

Others will give a better answer, but I suspect that Windows validation will consider this a "significant hardware change", meaning that it will stop working and/or you won't be able to update. Even so, it costs nothing to give it a try and see what happens.

How do i install sata hard drive?

ok, i am using right now my sony dvdrw on ide1 as master and ata hard drive on ide2 as master, booting to the hard drive. i am going to install an sata hard drive and use that as the boot drive, the normal ata as a storage drive only. how will i install the sata drive? do i install it to sata 1 and then durring the install of windows xp tell it to hit f6 for third party scsi drivers and then use the intel sata floppy driver disk that came with my board? it's the MSI-6728 board. or is there anything special i need to do in the bios or what?
oh yeah. what connection for power should i use? my powersupply has sata and normal, so should i use the sata power connector? and then what's this about legacy or something in the bios, or am i wrong?

Well first of all, you dont install the Intel S-ATA Driver Disc unless you are going to create a RAID Array....Go into the BIOS and on the "On-Chip IDE Configuration" Page Set the Options like this.........
On-Chip ATA Operate Mode : Legacy
ATA Configuration : P-ATA+S-ATA
Keep S-ATA Enabled : (Greyed Out Yes)
Keep P-ATA Enabled : (Greyed Out Yes)
P-ATA Channel Selection : Both
Combined Mode Operation (At first you have to set this to P-ATA Channel 1, then switch after you Move Windows to S-ATA)
Configure S-ATA As RAID : No
Then you are Going to have to Install the OS on The SATA and Just Move the Files that you want to save from the P-ATA HDD and then Remove the P-ATA Drive from the "Boot Device" List in the BIOS....
You really should List Your Full System Specs. When you POST...Create a "Signature" with your Forum User Control Panel...........Sean REILLY875

Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
So to sum up, the symptoms I'm seeing:
MacBook Pro CAN see internal SATA hard drives.
MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

UPDATE: An interesting development!
I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
Onward!

MacBook hard drive and SATA hard drive

Can I use the Hitachi’s Travelstar 5K160 HTS541616J9SA00 2.5-inch SATA hard drive to, instead of putting their drive in the enclosure (it doesn’t come pre-installed), put my MAC Book (black model) hard drive in? I want to transfer the data from this hard drive into another MAC Book. My original computer had a problem with the board but I have my hard drive with data intact. I want to buy this SATA but am not sure if this would work, if I can put in the MacBook hard drive as if it was the SATA one... Help, anyone? Thanks!
MacBook Mac OS X (10.4.10)

Hi there,
A number of people on NewEgg's product page for that drive say it's great for a MacBook, so I'd assume it's ok.
You can put your old MacBook hard drive into any external USB2.0 enclosure and retrieve the data.
Regards!

I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3??

I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3?? That seems to be just about all I can find out there, so far. Are those drives compatable with this macine? thx

SATA II

I am replacing my existing SATA hard drive to a Solid State hard drive and want to image the drive, is this possible?

I am replacing my existing 320 GB SATA hard drive that clicks and makes weird noises to a Solid State hard drive and want to image the drive, is this possible? I then want to replace the DVD with a secondary large drive for storage.
So I am looking for any "gotchas" that I may be unaware of.
Thanks!

Put the Old drive in an external notebook drive enclosure. Install the SSD in your computer. Boot from your Old drive's Recovery HD:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Clone Lion/Mountain Lion using Restore Option of Disk Utility
     1. Select Disk Utility from the main menu then press the Continue
         button.
     2. Select the destination volume from the left side list.
     3. Click on the Restore tab in the DU main window.
     4. Select the destination volume from the left side list and drag it
         to the Destination entry field.
     5. Select the source volume from the left side list and drag it to
         the Source entry field.
     6. Double-check you got it right, then click on the Restore button.
Destination means the New SSD. Source means the external Old hard drive.
Set the new Startup Disk to the SSD and restart the computer.
This process clones both your old OS X volume and the Recovery HD volume to the SSD. You can use a similar process to clone the SSD to the new hard drive you will install.

Ejecting problem on my 2nd SATA Hard Drive Bay Caddy

I am having an ejecting problem with my caddy secondary HD.
Basically every time I close the lid, the secondary HD is ejected or, in case ejecting fails, I obtain an error message..very annoying situation.
How can windows 7 avoid to eject it? Do you know a best practice to configure properly the 2nd SATA Hard Drive Bay Caddy??
Thanks in advance!
Fabio
Solved!
Go to Solution.

Really sorry, I didn't explain properly: I was talking about Ejecting OS side (windows 7 eject my secondary HD when I close my laptop, consequence is that I don't see it anymore in Computer).
ejecting is when you press here
anyway Thanks!!

Replacing a ATA with a SATA hard drive

I have a Pavilion dv9000 laptop. My hard drive is getting full. Can somebody please tell me if I can replace the ATA hard drive with a SATA hard drive.
This question was solved.
View Solution.

Thank you for your help

Z600 Max SATA hard drive ?

Hi,
I purchased a refurbished Z600 work station and have not been able to determine what the max size SATA hard drive I can install in the system. The operating system is Windows 7 Professional 64-bit.
Thanks . . .

Hi:
You may also want to post your question on the HP Business Support Forum -- z Workstations section.
http://h30499.www3.hp.com/t5/Workstations-z-series-xw-series/bd-p/bsc-272#.VDPx1XktC9I

Installing Windows XP on SATA Hard Drive

Hey. I have a maxtor 80gb SATA hard drive that I put in my new computer, and I want to install Windows XP on it. I see that the computer recognizes that it's there, but when I do the F6 process to get the drivers for Windows I cannot get anything for some reason. I hit F6, and it gets to the point where it asks me to install a disk with drivers, and I put the floppy for the VIA drivers in the drive (I'm using VIA after all I've read), and nothing happens. I don't even hear the floppy doing anything. after a few seconds of "please wait" the same screen comes up telling me to put the floppy containing the drivers in. Does anyone know what the problem could be? Also, in bios, it seems to recognize my floppy drive, since it lists it, and I can use it as a boot drive. If someone could help me out, I'd appreciate it. Thanks.

Hi
What is meant is the floppy is controlled from 2 parts of bios.
1. go to advanced bios features, set floppy seek to enable, set boot sequence to floppy, CD, HDD(BB1 = SATA), enable other devices. Then go to integrated peripherals, make sure PATA IDE and SATA IDE are enabled, just below is floppy controller, enable that, then SAVE and exit,
If the floppy cable was inverted, the drive light would be on all the time, if it flickers oon and off, it is OK.
Now try the F6 routine, if it still does not work then a new copy of floppy may be needed.
Cheers
jocko

Installing a second SATA hard drive - Problems booting

Hi,
I currently have one Maxtor 160GB SATA hard drive in my system with my operating system installed. I have another identical hard drive that I'm attempting to install now, into the second of five available SATA ports on my MSI P965 Neo motherboard.
When I plug in the second hard drive, though, Windows will not boot. It gets to the Windows logo screen with the progress animation, but before even the animation can begin, it stops and the screen freezes. This does not fix itself with waiting.
My boot priorities are set to: DVD-ROM, CD-RW, hard risk. The hard disk priorities are also as they should be to my knowledge - although it can be tricky because when ordering, both disks have the same name. I have tried with either one on top of the list, and you cannot remove a drive from the list alltogether.
The SATA cable is in perfect condition. My BIOS is up-to-date.
When I plug the hard drive in when the system is already running, Windows will detect it and files can be written/read flawlessly. As soon as I restart, however, I run into the same issue.
The first HDD, with the OS on it, is in SATA 1, the second HDD is in SATA 4. Ports 3, 6, and 7 are unused.
I'm out of ideas at this point, I don't see any other options that need to be changed.
I'd appreciate any input you can offer - thanks in advance!

I would debug this drive you are talking about which clears off all data and partitions information. Take out the good drive and leave in the dodgy one. Boot to a floppy with this dell win95 boot disc.
http://support.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R19775&formatcnt=1&libid=0&fileid=19601
When at the A: prompt: type debug and enter, you get a (-) prompt and then enter the following script exactly:
F 200 L1000 0 (enter)
A CS:100 (enter)
xxxx:0100 MOV AX,301 (enter)
xxxx:0103 MOV BX,200 (enter)
xxxx:0106 MOV CX,1 (enter)
xxxx:0109 MOV DX,80 (enter)
xxx:010C INT 13 (enter)
xxxx:010E INT 20 (enter)
xxxx:0110 (enter)
g (enter)
q (enter)
restart your system.
Now you can put back in your first drive as well, boot up into windows and use the disc manager to repartition and format.
Old school! If you are still having problems I would replace the drive.

Should I get a SATA hard drive?

I am about to mod my Xbox, and I am going to buy a new hard drive, but what I was thinking was that I could use my current 160 gig IDe drive and upgrade to a SATA drive.
Is there any problem with using just one SATA hard drive with my current setup?
I might not reply until this afternoon, I am at school.
Thanks

To answer your question: No there is no problem using a SATA drive with your setup. Indeed SATA is one of the features of this mobo so if you can use it. You don't list your PSU so I do not know whether your PSU has SATA power connectors, either way you should get a molex to sata convertor cable with your sata drive.

Internal SATA Hard Drive

Just installed a seagate SATA Hard Drive into my expansion drive.
It was recognized right away, I formatted it and it mounted immediately.
However, the drive is SATA 3.0 and my system is SATA 1.5. There is a jumper setting on the drive to make it SATA 1.5, and I am pretty sure I set it up correctly.
My question is... if I had the jumper wrong and the drive was still in 3.0 mode, would it not work? Or could it possibly fry my system? I think I got everything right, but I am trying to make sure.
Thanks in advance for the information.
Message was edited by: Williams

So... here's the final details.
First, the "top" of the drive is defined as the silver side with the label. The guy I talked to from Seagate was very cool and said he had heard my question many times. So that answers the question about the jumper. Also, the jumper is FACTORY INSTALLED in the 1.5 setting. To change to 3.0 you just remove the jumpers.
Now, as to my question... if the drive was in 3.0 mode would it work in a 1.5 system? The answer is no. It wouldn't damage the system, but the drive would not mount.
However, if the system was 3.0 and the drive was in 1.5 mode, it would work. In this situation, it is backwards-compatible.
There you go, thank you all for your responses.
Message was edited by: Williams

T60 Sata 2 Hard Drive

Similar Messages

Maybe you are looking for