T60 will not power up (battery status led green, power status led green)

Ok so I have been researching this for a couple days now. Trying various things............
Including the famous 10 second power button press discharge.........
Symptoms:
1st Disclaimer - coffee was exploded all over the laptop but has been running for a month.
Symptoms:
It has been working post coffee spill (several weeks ago) as long as you left it running. I get cocky and turn it off then it wont come back on.
The laptop has exhibited the inability to power on since but I have been able to get it to turn on several times since.
green power light comes on with AC adapter only
plug battery in and the battery light goes green
press the power button - both lights go out
I replaced the keyboard, battery, tested for 20 Volts on the AC adapter, tested for 2-3 volts on the CMOS battery.
I tried testing for 20 volts on the motherboard where the power supply cable connects. I have most of the laptop broke down still.
I did get it running again last night as a result of me incorrectly using the multimeter and short circuiting the power supply connector .
It booted up and ran fine and I even tried turning it off and on again several times.
I thought it might be a heat issue. I turned it off and tried to turn it on this morning and it will not power up.
Same symptoms as before.
no battery, only power connected, green light comes on, plug in the battery, battery light goes green, try to turn it on and the lights go out.
It seems like it is fixable but I am not sure what to look for next.
Or should I be looking for another system board...........if so what should I replace it with
This is an IBM T60 Type 2613 15" screen.
Solved!
Go to Solution.

Welcome to the forum!
Your best bet would indeed be a new system board. Any single one from a non-widescreen T60/p will work.
I've got dozens of them available - send me a PM if you're interested.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

T60 suddenly switches off, will not power on again, DVD drive related?

I have searched and searched for this, and although finding many "T60 will not power up" I haven't
found any with this twist.
My T60 is ~2 years old, and the problem just started recently. Working on battery one day, the laptop
suddenly died - like instant loss of power. I could not turn it on again. One strange thing though:
When I removed the battery and re-inserted it, the batt-icon-light came on briefly (a blink). If I then pushed the power button it lit up for 1 sec and then went out, not booting. Repeating it, without removing the battery, it didn't light up.Ok, thinking maybe the power supply was dead, I took it completely apart, removing also the harddrive and the DVD drive. By chance I then saw that it had "fixed itself". I resembled it and it worked again, powering up like nothing had happend.
Then it happened again yesterday. I read in here about the "push power 10 times, hold power down 30 sec" etc, but had no luck with that. Again, when I inserted the adapter cable the light came on (power plug + batt light) but when pushing the power button they went off, and if I removed and reinserted the plug same thing again.
I then read about removing HDD and DVD drive, and that did it! So, it happened again today and this time I just removed the DVD - and it booted again.
So, after this loong description here I hope that some of you have tried/seen this before or have an idea what it can be. I left the DVD drive out, and it has not happened again...yet (it's been 5 hours only).
Ideas?
Thanks in advance!
Martin.
Moderator edit: Removed duplicate copy of message text.

Kaz wrote:
Hi Nordal,
I know this is an old thread, but since I too am now experiencing inability to startup by T60 and seems to be getting worse in the last months, I was wondering what additional things you may have learned in the last 2 years since facing this issue. My system will typically be in standby or hibernate and when I open lid to start it up again, Power and Bat light go out and cannot start it. No beep codes, nothing. Previously, recovery was to pull battery (which is now new Lenovo as of last month and working great), hit power button a few times and then hold it in, put battery back in and AC adapter, then it would start up. In last few days, this no longer works. I have to go through similar step, but now I have to startup only with battery, once in Desktop, I can plug in adapter and no issue until next time. I have three 90W AC adapter all putting out correct 19.5-20 VDC. Have rulled out an adapter issue, I believe. Concerned about something on motherboard being flaky, but cannot pinpoint issue. A few days ago when this happened, I had to pull CMOS battery, wait a few min., then put everything back together and was able to boot.
Have never pulled anything more than RAM, CMOS battery, main battery, and AC adapter. May have to try DVD drive next time.
Thanks,
Kaz
It's probably best to start a new thread instead of reopening one thats 2-3years old, but from what your describing it sounds like your slowly ruling out everything except the system board, nothing you don't know already.
I don't normally deal with T60's, my main focus is T61, but I do have a source for the boards if you were to need one, as well as having a source to get the older boards reflowed. Some of the older models had problems with solder connections cracking when the board would flex, which can be repaired on an infrared reballing machine. My friend Dominic (realblackstuff from thinkpadforums.com) operates a website where boards are collected and sent off to be reflowed in wholesale lots. It's quite reasonably priced, as are the T60 boards pulled form grade "A" corporate laptops, but lets hope you can find a lesser component that is causing the problems.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

L655 has solid white power LED and soid orange battery LED and will not power on at all.

L655 has solid white power LED and soid orange battery LED and will not power on at all. I tried a second power adaper. Any other suggestions? It does not even try to power on. No fan or any other noises.

if it is not powering up on battery or AC, then there is either something wrong on the motherboard keeping it from powering up, or a bad power switch. I personally have not encountered a bad power switch on any of my Toshibas, so I would suspect something with the motherboard. It is strange that it does indicate that your plugged in and charging. If you leave the power adapter plugged in, does the battery status eventually go white?
Qosmio X875 i7-3630QM, 32GB RAM, OCZ SSD Qosmio X505 i7-920XM, PM55, 16GB RAM, OCZ SSD
Satellite Pro L350 T9900, GM45, 8GB RAM , Intel 320 SSD (my baby) Satellite L655 i7-620M, HM55, 8GB RAM, Intel 710 SSD (travel system)

DV4 1275 Power Issue, Battery not charging, Will not Power with AC only

HP Pavillion DV4-1275mx
Battery will not charge, Laptop will not fully turn on with battery in (battery not charging at all). Laptop will not power on at all with no battery using only AC and with battery it will attempt to load and die due to lack of charge.
Have tried 3 diff HP chargers.
The orginial 1 that came with the laptop is dead and will not charge anything. Tried it on a diff HP laptop and not recognizing any power
The 2nd one is OE HP laptop diff model but same wattage that came with my gfs work laptop. I have charge my laptop with it before in the past however it is not charging the battery now either
The 3rd is a aftermarket generic one that my g/f bought in the airport and it works with hers as well however I have never used it on mine.
I have tried hard resetting.. taking out battery, holding power for a min and replugging everything.
Also when I remove the battery and plug in either of the chargers that do work the power LED are "not" lighting up on the front or the LED where the AC plugs into the laptop. Which makes you think the charger is bad however the 2 working chargers do work on my other 2 HP laptops.
If i plugin one of the 2 working chargers with the battery it will go through the boot process and as its starting windows it just dies and shuts off. The power led by the DC jack does light up and the charging light on the front lights up. However this only works when I unplug the battery and plug the AC charger in. After the laptop boots up to starting windows and dies. I have to remove the battery and replace it to get the LEDS to light back up.. If the MB was bad I wouldnt think any of the LED's would come on nor would the laptop boot up to the starting windows. If keep trying to turn it on the booting time is shortened as the battery is not holding a charge and sometimes it only makes a few seconds and then just dies out.
I dont have alot of money to spend so I was hoping maybe you could point me in the right direction.
Should I buy the replacement part OE charger for my specific laptop? (not sure if its going to be much diff than the others since they are all 65 watt chargers)
Should I buy a new battery as well?
Or does this sound like a short problem in the mother board or a solder issue with the DC plugin?
If it is an issue with the motherboard I do not want to go through the hassle of buying the battery and charger as I will end up having to just replace the laptop
If you could please advise me what direction to go I would be so greatful.

Dude, I have the same exact problem with mine. It's not a cheap fix either. It definitely is the motherboard.
I'm no expert, but I believe the problem is a dead capacitor on the motherboard preventing it to build up a charge.
I spoke with an HP rep, which told me it's $398 for them to fix.
I let them know that I didn't have another $400 to put into this laptop. So, they suggested I try reseating the motherboard. And also reseating the memory modules.
http://h10032.www1.hp.com/ctg/Manual/c01597750.pdf
That is a pdf of the laptop's manual. It'll help in reseating. Page ( 59 ) for the motherboard. Page ( 67 ) for the memory modules.
This hasn't helped at all with mine, but maybe it'll help with yours!

Macbook Pro will not power on without battery installed

Hi there,
I have a Macbook Pro A1226 that fails to power on without a battery installed.
i.e. will not run off AC power on its own. I have tried 2 other power adapters, no change. All 3 adapters are outputting the correct voltage without fluctuations.
But, if I am in OSX with a battery plugged in, shutdown the laptop, remove the battery while AC is still plugged in, it will power back on without any issues. But as soon as I remove the battery, it will not power back on using just AC.
Is this an I/O board issue, or a mainboard?
I have power drained the unit and reset the parameter ram.
Thanks

Any update on this? This is the same thing that's going on with my laptop right now. I was at the Genius Bar and they said they can send it in for repair. Takes 7-9 days and costs a minimum of $310. At the time I was there, my computer wouldn't start up at all, because the battery had drained to less than 20%. It didn't even start with just the power cord (no battery in). The "genius" finally got it to work by doing a PRAM and SMC reset. Got home and was able to recharge my battery to 100%. Used my computer for 2 days before I dared to take it off the power supply. Lo and behold, as soon as I take it off the power cord, then re-connect it, it shows "Not Charging". I tried to do SMC again, but no luck. Keeps saying "not charging". Even tried with a brand new battery. Do I have to get the I/O board thingy replaced?

Hp zv5242qv laptop with windows vista will not run on battery but will run on power adapter

Hello, I have a HP zv5242qv pavilion zv5000 series laptop with windows vista installed. I can run it on the power adapter with and without the battery installed but it will not power up on just the battery, the battery is new and fully charged. When I plug in the power adapter the battery light on the front of the laptop comes o then goes off, anyone have any ideas about my problem ?

Hello,
The situation you describe looks like the unit has problems with the battery, but you say the battery is new and is fully charged.
Then, the issue might be with the system board and maybe there isn't anyhting you can do.
You can try to remove the battery and the ac adapter, and keep the power button pressed for 30 seconds, then connect the ac adapter, turn on the unit, then when in windows put the battery in place, see how it is detected, the power level and restart the PC. See if the unit restarts with the battery in place, if yes, then shutdown the unit.
See what happens and report back.
Thanks,
I work for HP! Please remember to provide and if this helped click ON

HT1430 My iPhone 4 will not power on. When connected to iTunes it shows battery at 100%. Pressing and holding the sleep/wake button does nothing; just a black screen.

My iPhone 4 will not power on. When connected to iTunes via my computer, it is recognized and shows fully charged battery. Pressing and holding the sleep/wake button does nothing; just a black screen. Any suggestions?

Only way is to bring it to the Apple Store and use the warranty if it hasn't expired

Mac Book Pro will not start on Battery Power

Mac Book Pro will not start on Battery Power although battery at 98% need to connect charger. When started date and time incorrect, comes up as 1st Jan 2012.

What is the exact model of your MBP? The date change often is an indication of power loss to the MBP, such as disconnecting the battery.
If the SMC reset does not solve the situation, post this from your MBP:
Make certain that the power adapter is connected.
Ciao.

MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolv

MacBook Pro turns on but will not load. Battery will power up and charge. The PRAM second start up seems to work, but the Apple timer continues add-infinitum. There is also a disc in the laptop so I can't load re-load software OS 10.6.1. How do I resolve this problem?

Try booting in Safe Mode by holding your Shift key down when booting. Also, try holding the eject key down when booting to eject the DVD. If you plug a mouse in and hold the clicker down when booting, that should eject the DVD.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101

My 13.3" macbook pro will not power up.The battery indicator light does not come on.The Mag safe charging light flickers green and red dimly.I had a cell phone connected to the USB port.

My 13.3" macbook pro will not power up.The battery indicator light does not come on.The Mag safe charging light flickers green and red dimly.I had a cell phone connected to the USB port.

This didn't work for me, so I did a bit of searching and TONS of pages later in google, I found an answer. Here are the steps for people who also were in my situation:
1. Take off bottom case
2. Unplug battery - blurry image here: http://i.ytimg.com/vi/03cC79r5Dx4/0.jpg
3. Press and hold power button for 5 seconds
4. Plug a charger in, and it should start booting up
5. After shutting down again, reconnect the battery and close the case up
6. It works! (hopefully, if you guys had the same situation I did)

HT3964 macbook pro will not start on battery power works fine when plugged in

My macbook pro 15 inch early 2008 model will not start on battery power but works fine when plugged in.

check the battery info.. >about this mac>more info>system report and select "power" on the lefthand column. How many cycles? What does it say about the condition? etc.

HT1414 Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on :(

Anybody have an ipad that will not power on, for no reason? My ipad always worked fine and then one day it shut down because the battery was low so I plugged it in and it will not power on. Tryed the hard reset option still no power on

You can try recovery mode to see if you can revive the iPad.
http://support.apple.com/kb/ht4097
Have you left the iPad charging for a couple of hours or so to be sure?

Compact Battery Pack CP-E4 to Speedlite 600EX-RT will not power on.

I attached the Compact Battery Pack CP-E4 to my Speedlite 600EX-RT and it will not power on. The battries are fully charged. The flash works with the battries installed in the flash unit. Is there some thing else that I am suppose to do?

Hi Tazdog!
Thank you for posting about this.
When using the CP-E4 with the Speedlite 600EX-RT, it is still necessary to have batteries inside the battery compartment of the flash. The flash needs internal power to function and allow you to control the flash. With the CP-E4 connected, it will draw power from it and the internal batteries to recycle the flash.
Even though internal power is necessary, you can still set the flash to draw the recycling power from the CP-E4 only by changing Custom Function 12 to [1:External power only].
This didn't answer your question or issue? Find more help at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

My ipad will not power on after update. I have tried connecting to computer which doesn't recognize it. I have pushed top and circle buttons at same time. It had a battery charge before it died. I tried to stop the upload and am afraid it 'crashed'

My first genteration ipad will not power on after update. I have tried connecting to the authorized computer which won't recognize it - does not acknowledge a device is plugged in. I have pushed top and circle buttons at same time. It had a battery charge before it died. I tried to stop the upload midway and am afraid it 'crashed'

Try putting it into recovery mode.
Connect iPad to your computer via USB while it's turned on.
Open iTunes
Hold the iPad's Sleep/Wake switch (power button on the top of the iPad) down until the "power off" slider appears.
Power off the iPad completely (wait for the progress spinner to disappear).
Hold the Sleep/Wake switch AND the Home button down for a full 10 seconds.
After 10 seconds (the second time you'll see the Apple logo on the screen) release the Sleep/Wake switch while still holding the Home button.
Continue to hold the Home button for another 10 seconds until the USB connection image appears on the iPad's screen, then release the Home button.
A pop-up message will appear on iTunes saying it has detected an iPad in recovery mode, you must restore...
Click on the "Restore" button and the process will begin.

IpodT auto redirects to the power off (slide) option while in use. Then while not using it, it will not power off to conserve the battery. I have to enable the assistive touch to save battery life. Software is up to date with 6.1.6. PLEASE HELP!

version 6.1.6(10B500); model#MC547LL/A; 60GB (40 used/20 avail)
IpodT auto redirects to the power off (slide) option while in use. Then while not using it, it will not power off to conserve the battery. I have to enable the assistive touch to save battery life. Software states up to date with iOS 6.1.6. PLEASE HELP!

Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

T60 will not power up (battery status led green, power status led green)

Similar Messages

Maybe you are looking for