T60p LCD panel died - which kind do I have?

T60p LCD panel died - red screen for 30 seconds at startup then blank.
How do I find out which lcd panel I need for my T60p? Diagonally measures 14 3/16" from corner to corner of the plastic bezel.
Solved!
Go to Solution.

Hi,
What is the 7-digit type/model number and 7-digit product ID on the back of your laptop (so we can confirm that it is a 14.1" model)?
Reddish glow sounds like your backlight is out. If you shine a flashlight into the screen, can you read what's on the screen? If possible, hook your T60p up to an external monitor. If it displays perfectly, then more than likely your system board is fine and it's just the LCD that needs to be replaced.
Any 14.1" 4:3 standard panel from another T60, R60, T61 and a few other models will work. Some are XGA (1024x768 resolution) while others are SXGA+ (1400x1050 high resolution). If you have a T60p it likely came with SXGA+ resolution to match the more advanced ATI graphics processor.
It's best to find a used, genuine Lenovo panel, or, even better, an entire LCD assembly, which makes for an easier swap. Look for a genuine panel with a Lenovo FRU part number printed on the back. "Compatible" or generic (non-O.E.M.) panels are often of inferior quality and may not function properly once installed since the EDID chip has not been properly programmed.
Here is the Hardware Maintenance Manual for your T60p: http://support.lenovo.com/en_US/detail.page?LegacyDocID=migr-62733
Have a great day. (I do not work for Lenovo)

Similar Messages

R50p LCD panel compatible with a T42p?

I found a cheap R50p (1833-BU4) and I noticed it has the same 15" UXGA LCD panel number as my T42p (2373-Q1G) = 92P6683
I wanted to get it; to have some kind of backup on the LCD panel for my T42p, and it would be a lot cheaper instead of buying such lcd panel off ebay or some webshop.
My question is, can the panel from the R50p be swapped into the T42p without much problems? Would it fit the lid? Are any of the the cable/connectors mabe different?
regards,
MrSnake
T42p 2373-Q1G (PM765, 2GB, 250 GB HDD, 15" UXGA(1600x1200), 128MB ATI FireGL T2)
T60p 8741-C4G (T7600 2.33GHz, 3GB, 320GB 7k2 rpm, 15.4" 1680x1050, 256MB ATI FireGL V5250)
R50p 1833-BU4PM1.7GHz, 2GB RAM, 60GB 7200rpm HDD, 15 UXGA(1600x1200) TFT LCD, 128MB ATI FireGL T2

it's the same panel. they should swap over like legos.
ThinkStation C20
ThinkPad X1C · X220 · X60T · s30 · 600

T60P LCD issue

Hi all,
I've just gotten hold of a 2007 model T60P which I believe has the silly high resolution on the LCD via the Intel chipset however the screen has a small fault in that it will not display anything.
I can adjust the brightness, using the FN keys and the screen visably gets brighter/dimmer depending on the button pushed, and an external monitor works correctly when plugged in so I assume that its either just the LCD cable that has gone or the actual panel is dead and I need to get a replacement 15" monitor (no problem there .. ebay) but just wanted to check my logic on thinking its actually the panel rather than the the inverter/chipset/cable.
Also on the replacement screen is 1400 x 1050 (SXGA+) really the highest resolution for the 15" panels or can I go higher resolution if I can find a supplier for them?
Many thanks in advance
Dino

Your logic seems solid.
Since the external monitor displays, graphics chipset should be good.
Bad inverter should display a very dim screen, but visible.
If you are comfortable taking things apart, you could reseat the cable.
The best way to get an exact panel replacement is get the model number
off the panel itself. More dis-assembly.
Try to stick with a matched panel.
No absolute, positive, 100% answer here, it could still be any of the things you mentioned,
but faulty lcd panel seems most likely. And of course the most expensive!

Replacing the LCD panel in my 23" Apply Cinema monitor (A1082)

Hi,
I have a 23" cinema screen (A1082) which has a cracked LCD panel. I've order a replacement LCD panel but how do I take my existing monitor apart in order to change the LCD panel out? There doesn't appear to be any screws to dismantle the screen...... thanks

1) Using a thin tool like a screwdiver, pry off the side plastic strips from the top down. Older units are harder as the glue is applied more generously. It helps if you warm it first, lets say with a blowdryer.
2) It is easier if you remove the stand hinge pins using a 6mm allen wrench. You can probably get away skipping this step if you don't mind more work later.
3) With a small phillips head, remove the side retainer brackets.
4) At the bottom where the clamshell joins, pull a small tab which slides a hooked retainer releasing the clamshell. Older units may have one on each end, newer units have one at only one end.
5) Pop apart the clamshell and slide the guts out.
Good luck finding replacement parts for these. Mine has a logic board that died in a power failure and I am stuck with finding a broken display and buying it for the working parts. Unfortunately Apple does not sell the parts to end users.

What's the latest Jan. 2010 spec LCD panel model #? (e.g. 9CBD, 9CA0, etc.)

Just wondering if anyone who has a 2010 assembled 13" MBP or recently warrantied MBP can confirm the latest Apple display spec model # (e.g. My MBP was built in Sept.09 and has a 9CBD panel) that is being used?
Got the dreaded light leak developing on the side and hinge edges of my MBP -- but considering that my colours/calibration are pretty much bang on for my eyes as well as the fact that I've painstakingly applied an Anti-Glare film 100% free of lint bubbles LOL -- my conundrum if the latest spec'd panels are really any better or if it's still a lottery on whether you get a good panel if replaced under warranty. The last thing I want is to go backwards in quality!
Also if you've gone through the warranty process I'm curious on whether you have any say on whether it is another 9CBD that goes in or if you can specify to them that you're only satisfied if a Jan. 2010 9CA0 (or whatever # it is) is put in?
I am planning to wait to see if Apple quietly updates the LCD panels in the MBP line at the Jan. 27 iTablet/iPhone OS4.0 event before taking it in anyways, but hopefully someone can shed some light into how Apple have been going about dealing with the light leak issues. Thanks again.

Thanks for your kind cmments matrixxzero. I agree rockykoston I will replace my keyboard eventually myself too, with all the stories here I'm terrified to hand my laptop into service, apart from not having the spare time, Idon't want it to come back scatched, damaged and/or unfixed. That doesn't augur well for Lenovo guarantees. I am fully cpable of servicing it myself but many customers aren't and shouldn't have to.
As I say the other issue is model lines. Our Chinese friends have proven they can maintain quality and innovate now but their shere manufacturing muscle means it's all too easy to have too many models and too many variants with too much crossover.
Why drop a great design like the Z710, only let down by a middling to poor Nvidia chip and introduce new 17.3" models with absolutely no maintenance covers and sealed batteries!! They should have upped the Nvidia chip (the same as the Y50) and a better WLAN card. Same with the 15.6" models - evolve the Z510 to have a case like the Z50 but the same or better components again. Similarly the Y50 should have been an evolution of the Y510 not a step down.
Lenovo has definitely gone cheap in the upper end of the consumer range, when they needn't as there are tons of cheap laptops from the brand.
Most of the reviews I came across for the Z510 described it as having very good build quality and since I changed laptops three times from the same store within my purchase period I had chance to compare closely, with at least Toshiba and Acer. I would not agree with these reviews it's OK but not great. The metal upper case fooled me a bit but it's less sturdy than a cheap i3 HP laptop it replaced. Again for around a $1000 it should be better.

Some LCD panel info

Hello all,
Like quite a few people on this forum, I recently purchased a new MB 13" aluminum and have been very disappointed in the quality of the LCD panel. In particular, I feel like the viewing angle on this display is significantly worse than my old Thinkpad X41 tablet, which is going on 4 years old. So, I went in search of some technical information, which I figured I would share...
There are three main technologies for TFT (thin-film transistor, or "active matrix") LCD panels. Twisted Nematic (TN) is the most popular type of panel because it's cheap to manufacture and has very fast response times. However, image quality on the TN panels is the worst of the three technologies. In Plane Switching (IPS, S-IPS) is the best quality panel, but is expensive to manufacture and has relatively slow response times. Vertical Alignment (VA, PVA, MVA) is a mid-range technology, somewhere between the cost of TN and quality of IPS.
This site provides a very nice explanation of the pros and cons of the three technologies:
http://www.pchardwarehelp.com/guides/lcd-panel-types.php
The vast majority of displays (notebooks and desktops) use TN panels because it keeps costs down and because the fast response times are better for games and movies. This trend was probably reinforced by the explosion of LCD televisions: for TVs, good response time is critical and vertical viewing angle is totally irrelevant.
There seems to be a consensus that all three lines of MacBooks use TN panels, but possibly with different levels of quality. I could not find much information on what causes quality to vary between panels that use the same technology (i.e., why is one TN panel better than another.)
Most IPS panels go into high-end displays, such as the Apple 30" Cinema display, for applications where image quality is crucial. It turns out -- and I did not know this at the time -- my old Thinkpad X41 is one of the few notebooks ever made with an IPS panel. I suspect they chose this panel because a tablet PC must be reasonably readable from a wide variety of angles (for example, laying flat on a desk), or it's useless.
So, maybe we just have to wait for a MacBook Tablet...Jobs, are you reading this?

SZGuy, nice digest of LCD info. You had me with every point except the one about viewing angle being irrelevant on a television. How so? When a family sits distributed around a room, all are entitled to a good view of the telly.
Every TV of at least 32" or larger uses a wide viewing angle technology panel. IPS and PVA are still hugely important in television and I don't see that changing soon. In fact, it is TN that is irrelevant in the world of TV.

MegaPC 180 - Programming LCD Panel

Hi All,
I recently built my MegaPC180 and what a lovely machine she is too!. My old machine sounded like an aircraft taking off!, this is nice and quiet with lots of mod-cons in a SFF barebone.
One thing I'd like to take advantage of is the LCD panel at the front. I know the PCAlert tool uses this, and by the looks of things it doesn't make any direct calls to the dll file which I thought may be the API for the panel.
I'm very familiar with C++ and VB and want to use the panel in several utilities I've created.
I found the msidrvif.dll file in the Program Files\MSI\Common\Bin folder. It exports the following functions...
DIF_CheckHardware
DIF_CheckMBType
DIF_CheckModel
DIF_CheckOEMModel
DIF_FS_SetAPStats
DIF_FreeDrvIF
DIF_GetDriverSelect
DIF_GetModelName
DIF_GetVideoFormat
DIF_InitCheckDevice
DIF_InitDriverSelect
DIF_InitDrvIF
DIF_RD_AudioOff
DIF_RD_AudioOn
DIF_RD_CheckLock
DIF_RD_GetDefMem
DIF_RD_GetRemtKey
DIF_RD_LMute
DIF_RD_PanelOn
DIF_RD_QueryLockLevel
DIF_RD_RMute
DIF_RD_RadioOff
DIF_RD_ScanFreq
DIF_RD_SelHWMem
DIF_RD_SetArea
DIF_RD_SetBand
DIF_RD_SetDefMem
DIF_RD_SetEQ
DIF_RD_SetFreq
DIF_RD_SetHCC
DIF_RD_SetHWMem
DIF_RD_SetLCDTime
DIF_RD_SetLEDPanel
DIF_RD_SetMono
DIF_RD_SetSIJ
DIF_RD_SetSNC
DIF_RD_SetSRS
DIF_TV_AudioOff
DIF_TV_AudioOn
DIF_TV_FineTune
DIF_TV_GetFreeScanStatus
DIF_TV_SetChannel
DIF_TV_SetCountryCode
The unfortunate thing is....I don't know the syntax of the functions, such as params, and returns.
I'm hoping someone from these forums, or from MSI technical could tell me the declarations so I can get over this hurdle?

Hi Andy,
Perhaps you have already read the posts regarding control of the LED panel. Anyway, I have done a little research myself and was able to obtain the specifications of the Bluebird VL+ controller which actually controls all the pc-off functions (and the LED panel). In theory this controller can perform more tasks than MSI used!
I also contacted Liteon Optoelectronics for the design specifications of the MSI LED panel. Unfortunately they are not allowed to release them (prohibited by MSI). However, I found the blueprints of another LED panel from Liteon with a comparable product code. I think it is likely that Liteon used the same design basics when building the MSI panel.
You can send a p-mail when you are interested in these .pdf files.

Purchased a LG FHD LCD panel and broken.

Hello everyone, I am using T520 4242- RU2 model in Thailand. I tried to upgrade my LCD panel from 1366*768 to 1920*1080. I bought a panel in e-bay and I replaced by myself. After few months, it becomes yellowish color on white image. So I removed it and replace default one. Well, I would like to buy a new FHD panel again. Do you know which one is recommend? AUO or LG or Chimei or whatelse...?? if you have recommended P/N or FRU, could you let me know? thanks and best regards,
Solved!
Go to Solution.

Thanks again Tasurinchi
I checked it is "bingo" and brand new P/N:42T0764 FRU:42T0765.
confirmed with seller. So I already purchased it.
I just don't mind about even if seller will send me compatible one.
it's just like gamble. I believe my luck. :-)
This is very helpful forum for ThinkPad users.
I am so happy that I meet a nice person like you.
Now I have 2 units of ThinkPad. and they work good.
X100e dual core model with SSD + 4GB Ram
T520 4242RU2 i7-2720QM with SSD + 8GB Ram

T500 WXGA+ LCD Panel Adjustment Challenges

Does anyone have any LCD Panel adjustment tips for a T500 with 1680x1050 screen and Intel 4500HD GPU?I am trying to make adjustments through the Intel Graphic Media Accelerator Driver Control Panel. I am running Vista Home Basic.
A number of different calibration programs such as Calibreze start by having you set the contrast to maximum. When I do this it washes out the screen so I back off on the contrast and try to proceed through the test but the result is that the color saturation is lacking. I am further frustrated by the video settings button on the same control panel. When I change the settings here it appears to have an effect only on the small test photos provided in the adjustment window. It has no effect on the display itself. I found a bunch of color management options in Vista but I have no clue as to where to begin with these. Lastly, I tried to find a user guide for but came up with nothing.Does anyone know where to find one?
I am left wondering why I didn't just buy a machine with a dedicated graphics card.
Solved!
Go to Solution.

Hi Doublej,
You don't say what is your purpose in adjusting your screen. If it is to have a truly calibrated monitor for the purpose of photo editing, then I recommend that you just give up on the laptop's screen anyway, and use an external monitor. The external monitor should be of type IPS or MVA or PVA (Wikipedia / Google these if you're not familiar with them) if a flat panel, or a (gasp!) CRT. All of those options are expensive, except the untrendy CRT. Just about every laptop screen these days and most external flat panels too use TN technology, which is great for gaming (fast response time) but utter garbage for viewing angles and color accuracy. Don't believe me? Load up a color photo on your laptop, then try looking at it from slightly above center, slightly below center, left of center, and right of center. See the color and brightness shifts? How can you possibly calibrate that? (You can't -- there's no way to always look at the screen from exactly the same angle, even if you could position your head perfectly, your eyes see different parts of the screen at different angles.) A good external monitor will also give you far better contrast ratio (brightest / darkest areas).
After getting a decent monitor, it's still a good idea to calibrate it. (I've seen some monitors from Dell and Apple come pretty close without calibration, and others that were way out of calibration by default.) The X-Rite i1 Display 2 screen calibrator comes with easy-to-use calibration software for Windows and Mac. (Other calibrators may be just as good but I haven't used them so don't know.)
The FlatPanelsDK Online Monitor Test is great for a quick visual check of your screen's calibration.
One last thing: discrete graphics have NO color calibration advantage over your fine Intel integrated graphics.
Results of Your Ideal Business-Class Laptop survey, concluded 2009-07-29.
Did someone help you?
Say thanks! with a kudo.
Even better: Pay it forward, help someone else.

Hi, I have a 3 year old Macbook Pro 13" and I accidentally cracked the outer screen of my mac book, however the LCD panel is fine and works well. Please advise what to do

Hi, I have a 3 year old Macbook Pro 13" and I accidentally cracked the outer screen of my mac book, however the LCD panel is fine and works well. Please advise what to do. I live in India and I have gone to authorised Apple technicians and they infomed me that I will have to replace the LCD panel as well even though it is not cracked, is this really true or can I just change the outer shell? Also they say that they cannot do it in India... can I do it myself at home?

Since it is 3 years old find a local repair shop that can replace the glass Only. you may have to send it out to a Non Local shop for that but there are some that specialize in doiing that on Mac notebooks.
Apple will ony replace the complete screen enclosure with all normal parts included, LCD, Camera, Aluminum housing and glass as one unit. Which is very expensive. Or you could just use it as a desktop system with external monitor and buy a new notebook.

IBM Thinkpad T30 lcd panel..replacement in due?

My lcd display panel is blurry (i.e. brightness level is not as expected though pressing Ctrl+Home)...
Maybe should entire unit be replaced? In this case, how to locate the correct version as (2) types, XGA and SXGA are
available..
Where can i find panel FRU number?
If you fool me once, shame on you...
If you fool me twice, shame on me!

Welcome to the forum!
A couple of things come to mind here:
a) Go into BIOS>Configuration>Display and make sure it's set on "high". Press F10 to save and exit.
b) Is the LCD slightly reddish/pinkish on initial boot? If yes, your backlight is dying and need to be replaced. Most people prefer to replace the whole LCD panel, though.
c) If your LCD is not red or pink on boot, your inverter may be on its way out. Replacing it is a cheap and easy job, and that's where I would begin.
All the FRU numbers and instructions on "how to" can be found in the HMM that can be downloaded here:
http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-42308
Good luck and let us know.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

DSC-HX90V LCD panel shows images upside down

I bought the DSC-HX90V for my wife in late June, and we promptly took it on a three-week cruise and visit to Italy. The camera performed well, even in low light, and the telephoto worked phenomenally: Thanks to the 5-axis OIS, we were able to take 30X zoom images with exceptional clarity and no blurring (even when shooting distant ferries, containerships, etc. from the deck of a cruise ship). The viewfinder was a great convenience, and it was easier to use than we might have guessed (popping it up and flicking the back element of the finder out quickly became an instinctive process). But--and this is really weird--the camera developed a fluke after several days of use: the LCD began displaying images upside down, in both shooting and review modes. At first this happened sporadically, then it happened all the time, and finally--in the past few days--it reverted to displaying images correctly. Fortunately, there were two workarounds when the LCD was acting goofy: We could use use the viewfinder (which was immune from "upside down syndrome") or pull the bottom of the LCD panel out an eighth of an inch or so, which resulted in upside down giving way to right side up. I haven't yet called Sony's warranty service about this, but I'm guessing the problem is in the LCD's "selfie" position sensor. It would be great if it could be solved with a firmware update or system reset, but that's probably too much to hope for. In summary: Great camera, but with an annoying flaw that will need to be fixed.

Hello Imboden,
Sorry to know that you are experiencing this issue with your camera. Please try to reset the settings in the camera by pressing MENU then Setup then Setting Reset. You can also do a Power Reset by turning the camera off, removing the battery. Press and Hold the On/Off button for a minute and then release it and reinsert battery. Turn on the camera and test the LCD screen.
If the LCD panel still does not work properly, I would recommend sending the camera in to http://repair-camera.com/SonyRepairHome.aspx for evaluation and repairs.
If my post answers your question, please mark it as "Accept as Solution".
Thanks,
Zander

Toshiba 8" LCD panel - Need pinout diagram

I bought this LCD panel (part # LTA080B820A) specifically because it said it had analog RGB input instead of digital inputs that most LCD's accept.
http://www.geeks.com/details.asp?invtid=LTA080B820A&cat=MON
Now i need to find a pinout diagram that tells me which pin does what on the input connector so that I can wire it up.
Anyone have a clue where i can find a pinout diagram for it, or know of a way to test the pins.
I figured since it is analog RGB i should be able to solder up a homeade VGA cable, would this work?
Help if you can .
Thanks,
-Krys

Hi
Such technical manuals are not for public and I think you should get in contact with an authorized service provider. Here its only an user to user platform and I doubt that you can get these informations here.
Anyway, here you can search for an ASP in your country:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider

Replacement LCD panel - good source

Who would be a good dealer for the LCD panel only? I don't want one in a housing, cost way too much.
I will be working on a white 2ghz core 2 duo. can be matte or glossy.
I'm doing this for a project & want to learn more about doing this type of work, so please don't advise sending it in.
Thanks!

I've used powerbookmedic once before, busted a key off my old powerbook one time. It showed up scratched & I was grumpy about it, wrote them a not very nice email. They did try to contact me & make it right tho, so in their defense. The broken key was in really good shape & used the suspension, which was the reason it was broke, so really, it all worked out.
I will keep them in mind, looks like with a coupon code & cheaper shipping rates, better price than ifixit right now. Thanks!
Anyone else have input please share!

Z61m: LCD panel replacement (WSXGA+ to WUXGA)

I own ThinkPad Z61m (Type 9450-HAG). Unfortunately the LCD panel does not work any more (only top third of display works).
I consider replacing of the LCD panel (WSXGA+, FRU no.: 13N7020).
Is it possible to replace the original panel with WUXGA panel - 13N7198 or 13N7178?
If it is possible, is it enough just to exchange the panels or it is also needed to replace other parts of notebook and/or upgrade BIOS or other software?
Solved!
Go to Solution.

It should work no problems. In fact, you could probably use your old inverter. CCFL backlit LCD screens use a two pin connector from the inverter to the LCD. This connector is the same accross most if not all manufacturers.
I tried replacing a 15.4" WXGA LED backlit LCD with a WXGA+ CCFL backlit LCD. Now you might ask yourself, can I convert to LED backlit LCD. While it may be possible, I don't want to say yes just yet. Anyways, what I had to do is disassemble the LCD and remove the screen. I disassembled the original WXGA LCD and replaced it with the WXGA+ LCD. Too bad it didn't work. It wasn't because I had damaged it. The LCD originally didn't work. It had an awful display. I just wanted to know if it was possible.
The conclusion is that these parts are quite interchangeable. CCFL backlit LCDs generally use the same connectors for both the backlight and display. I am not sure about LED backlit LCDs, but it would be understandable that the manufacturers maintain some kind of uniformity. After all, they produce these LCDs for all the laptop manufacturers.
\\ I do not respond to PM regarding individual tech support. Keep discussions in the forum for the benefit of others //

T60p LCD panel died - which kind do I have?

Similar Messages

Maybe you are looking for