T61 and two SSD disks

Hi all,
I'm new here so let me thank you all because I've found many answers regarding T61 on these pages. Your knowledge was of great help to me.
I've been using T61 for almost 3 years now and it's really a great piece of hardware!
I have an OCZ 60GB in as a primary disk and it really boosted performance of T61, not to mention battery life.
For 6 months now I have my old HDD in ultrabay (cheap ultrabay caddy from eBay) and everything was working just fine.
Few days ago I got myself a new OCZ 256GB SSD.
I've put it in ultrabay, initialized it and when I tried to format it, it locked up.
So, I've formatted it in my PC, tested it (wrote files, read files, played files from it), and then put it back in ultrabay.
It's than recognized as a disk, I can open folder that I have copied from my PC, but when I try to read or write a bigger file it locks up again.
So, I've put my primary OCZ in ultrabay and tried to boot from it and after few seconds of initializing windows it locks up.
I don't know if my cheap ultrabay caddy is something with a really bad chip inside and it's a culprit or is T61 ultrabay controller too slow so it just can't handle the load of SSD?
Any help would be greatly appreciated!
Thank you!
Best regards,
Walter

Hi,
I was wondering, what exactly is the speed of T61 ultrabay PATA controller?
On the other hand, my T61 has two free mini PCIe slots (one just right to WLAN card and another bellow CPU)
Would a mini PCIe to SATA converter/adapter be enough? Like this one:
http://www.ebay.com/itm/Mini-PCI-e-PCI-Express-to-SATA-SSD-HDD-USB-Adapter-DIY-/270564958436?pt=LH_D...
or do I need a mini PCIe to SATA controller? Like this one:
http://eu.startech.com/Cards-Adapters/HDD-Controllers/SATA-Cards/2-Port-Mini-PCI-Express-Internal-SA...
Of course, there would be some DIY involved but that's o.k.
Thank you!
Best regards,
Walter

Similar Messages

What is the real Weight on Macbook Pro 13'' with SSD Disks!

Hi all,
I think that there is some weight difference between Macbook Pro with and without SSD disk. Isn't?
With normal SATA disk it have 2kg. How many kg with SSD disk???
Tks,
Paulo

If there is it would only amount to a few ounces.

Install SSD, running macbook pro with two operating system and two hardrive

I am currently running bootcamp with Window 8 and Mountain Lion. I am about to install a 256gb SSD, replacing the optical drive. The partition on my current setup is 125 gb for window 8 and 125 gb for OSX. Since this is the first time I am running a computer with two hardrive and two different operating systems, how should I go by installing (software) my SSD. Should I just make one hardrive run window and the other one run OSX. Is it possible to move the OSX partition to the SSD. Should I just install both window and OSX again on the SSD? What are some other options?

It is possible, use Target Disk Mode How to use and troubleshoot FireWire target disk mode - Apple Support

RAID options, SSD disks and others....

Hi!
This is not exactly topic for expanding my mac pro... This is more "How to expand my upcoming mac pro".
There are couple of things I'm constantly fighting. Memory and disk-speed. I absolutely hate it when I see spinning beach ball on the screen and only thing I hear is the wild hard-drive trashing ...
Now when I finally upgrade my power mac G5 to Mac Pro I'm confronted with myriad of choices:
Memory is easy - 12Gb BTO option 6x 2Gb sticks. This should satisfy all the requirements. Enough to work with. Enough sticks so it really is DDR and so on.
Hard-drives are the real pain. First of all I'd like to ask couple of questions...
a) Does OS X and disk-utily support making striped RAID-disks and use those as boot-disk? Idea was to install two fast SSD disks and stripe those. They have sufficient long MTBF so I feel confident using them striped for increased performance. Performance is blazing fast for boot-disk which directly translates into nice user-experience since boot-up is fast and opening programs is almost instant.
b) Performance characteristics on OS X disk-utily versus SoftRAID. Are there any noticeable differences? Disk-utility driver is single-threaded while SoftRAID is multi-threaded. How about creating boot-disks with SoftRAID?
c) How about using SSD drives and hardware RAID-card from apple? Any experiences with this?
At the moment I think the setup would be something like this:
4x 1Tb disk-drives with RAID-5 for mass-storage
2x SSD drives with RAID-0 for OS
Downside is that I think this would require both hardware RAID-card for RAID-5 and possibly software-RAID if hardware RAID-card doesn't recognize SSD drives. Or if I wan't to be able to boot into windows which I'm forced to do sometimes (Note! booting windows in Mac is against my beliefs!) then I'd need to leave small partition free on the SSD drive(s) and not include that in RAID-setup.
So satisfying the following is pretty hard:
- RAID-5 for 4 internal hard-drives used for mass-storage
- RAID-0 for 2 SSD-drives used for OS and applications
- Ability to dual-boot into Windows via bootcamp

a: If you make a striped RAID array (RAID0) with Disk Utility you can boot from it. I'm doing the same right now, with 2 OCZ Vertex SSD's.
c: Officially, the RAID card only supports drives Apple sells. Besides that, it would be a shame to use SSD's with the Apple RAID card, as it is slow. If you have 3 SSD's in a RAID0 setup they will be faster than the RAID card can handle (the RAID card's maximum speed is somewhere near 533MB/s, look up the exact number in the Apple Online Store).
I don't think you can use Bootcamp when using the RAID card. In any case, you can't start Windows using Bootcamp from a disk that is connected to the RAID card.
Also, you don't have enough connectors for 4 internal hard drives and 2 SSD's if you want to keep your optical drive.
You could go for a third party RAID controller, but then I'd wait with my purchase until more is known about the compatibility of those cards with Snow Leopard. Also, this probably won't work with Bootcamp.

Windows 7 all browsers constantly crashing and SSD disk has way to much used space than all the folders are combined in size.

I recently built a computer and was installing Windows 7 Ultimate 64 bit on it. I have a few problems going on. First of all all my browser are constantly crashing (including IE, Firefox and Google Chrome) on random reasons. I checked the conflicts on chrome
and there were none conflicting with it. I did the /sparrow thing to clear and fix corruption but that did not work. I've tried making a new user file in Chrome, same results. Another problem I've been having is that my SSD disk that I have Windows installed
on shows way to much space being used in My Computer. I checked all the file sizes within it and it is a maximum of 40GB all put togather but My Computer says only 28GB is free of 111GB SSD drive.
Here are the specs to my computer:
AMD FX 8350 CPU
Mushkin 16GB 1866hz RAM
Gigabyte Radeon R9 270x 4GB VRAM GPU
Gigabyte 990FXA-UD5 motherboard
600W Amrageddon PSU
120GB Mushkin Chronos Deluxe SSD
2TB SSHD Seagate
Anyone know what I can do?
P.S Drive cleanup freed only 500MB and the Recycle Bin is empty
P.P.S I moved the Program files from the SSD to the SSHD (If that matters) Also the download folder.

HH
1-You can check what is using the space with a free 3rd party tool called Treesize from Jam software
2-I believe you have a hardware issue and here is why.
Event viewer logs show
1-The platform firmware has corrupted memory (see snip)
2-The Browser are crashing because of something called a memory exception (Cx05) see snip
I would check for a BIOS update, configure your system to generate a user mode DMP file and upload it when they crash. Beyond that there are only a few events in EV (~300). We can alwasy use more.
You can configure Windows to create user-mode dumps. Create a System Restore Point first.
Copy and paste the following in Notepad and save as a .reg file, then right-click the .reg file and select "Merge" to add to the registry, a .dmp file should be created in the C:\CrashDumps folder:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\Windows Error Reporting\LocalDumps\explorer.exe]
"DumpFolder"=hex(2):43,00,3a,00,5c,00,43,00,72,00,61,00,73,00,68,00,44,00,75,\
00,6d,00,70,00,73,00,00,00
"DumpCount"=dword:00000010
"DumpType"=dword:00000001
"CustomDumpFlags"=dword:00000000
After the app crashes, can you then upload the dmp file via Windows Live Onedrive or other file sharing site.
The following link has information on using Windows Live Onedrive:
http://social.technet.microsoft.com/Forums/en-US/w7itproui/thread/4fc10639-02db-4665-993a-08d865088d65
More info on collecting user-mode dumps:
»msdn.microsoft.com/en-us/library···85).aspx
Wanikiya and Dyami--Team Zigzag

Two ssd 64gb raid 0 and two sata 320 w d hd raid 0

Hello
I am having issues getting the WD 320Gig hard drive's to run in raid 0
System see the SSD in raid 0 .......but not the WD's in windows 7..... during boot up it see the WD's in the boot up and in the raid screen
Thermal Take Dokker Case
AMD x4 970 Black clocked to 3.9GHz with OC genie lite .... just enabled it in the bio's and let it do it on it's own.
Corsair H50 water cooled
MSI 890FXA-GD70 mother board
1.80 bio's updated already
Diamond HD6850 GDDR5 1024MB Vid card
Two 4 Gig Kit's Crucial DDR3 Ballistix 1280 CL8 1.65VW/XMP
Two Micro Center Re-Badged ADATA S599 2.5 SATA SSD 64GB Hard drives running RAID 0
flashing utility has been done to the drive’s already
http://www.adata.com.tw/upload/downloadfile/ADATA%20S599%20Firmware%20Upgrade%20Tool%20V1.0.rar
Two WD 320 Gig Hard Drives Sata2 16meg's cache
Sony lightscribe DVD.
ViewSonic 27inch HDMI 1080p 100,000 to 1 contrast and 1 ms
Thank's for any help with this system... boots up to log on screen in 30 sec's and then after entering pass word it is on desk top in 10 sec's

I am not having any luck at all with this.... when I do get it to see the SSD's and I load the RAID driver at win7 driver install screen it all loads up fine and when it get's ready to go into win7 after rebooting I get a blue screen and reboot's..... blue screen flashes by so fast i can not read it...... also i took back the the Micro Center Re-Badged ADATA S599 2.5 SATA SSD HDD's 64GB and exchanged them for two OCZ Vertex 80GB SSD and swapped out the two WD 320GB for one WD Caviar Black 1TB 7,200 RPM SATA 6.0Gb/s 64meg's.... I am looking to RAID 0 the two SSD's and I just can not get it using the RAID hardware on the MB .... I have been able to do it in windows manager but it will not let me load OS on to them... I do have Win7 loaded onto the WD 1TB SATA HDD at this point hoping I could get the two SSD's in RAID 0 and did.... but only as dynamic and it will not let me load OS on to them... I had hoped to do and then delete the OS on the WD 1TB SATA hard drive
Thank you in Adv. for any assistance

I have a macbook pro non retina, and I wanna know, there is any problem if I take my computer turned on into my backpack actually is not a ssd disk thanks

I have a macbook pro non retina, and I wanna know, there is any problem if I take my computer turned on into my backpack actually is not a ssd disk thanks

it's fine if you leave it on.......i keep mine turned on while travelling with my macbook in my laptop bag and have had no issues.
if however, you plan on running around or jogging - it's better to turn it off.
but leaving it on will not hurt it.

MacBook Pro with SSD that has a limited disk space (120GB). Rendering in Project File (User/Movies/Final Cut Projects), it takes huge space and the limited disk space would not be enough for the whole editing.

I'm using MacBook Pro with 128GB SSD that has a limited disk space. As we know, when rendering in Project File (User/Movies/Final Cut Projects), it takes huge space and the limited disk space would not be enough for the whole editing.
My question is, Is there any method to get the rendering Projects file saved into an external hard drive which is connected with USB/ Thunderbolt/ Firewire, with huge disk space (eg. 500GB HDD).
Now, new project created in my Mac is automatically saved in (User/Movies/Final Cut Projects) and my Mac has ran out of space to hold the files.
Thank you.

You have at least 3 different ways to show the project library:
1) Go to WIndow->Show Project Library
2) Click the button in bottom left of your window:
3) Hit the keyboard shortcut (Command-0)
The project library will be shown, occupying the area where the timeline usually is.
Your hard disks will be visible. Click the hard disk where you want the new project to reside and hit Cmd-N to create a new project.

SSD disks and swap

I know this has been discussed numbers of times but still I find it confusing. My new PC will have a SSD (and no traditional hard disk). My question is what to do with the swap and especially the swapiness parameter? Is it really a good idea to reduce it? How the default value of 60 has been decided?
What confuse me is that I have seen too many posts that say, roughly, that we need to avoid any write to the SSD in order to spare it; often to the point we can wonder if the SSD will remain useful... I have seen that SSD supports 100000 write cycles; with a 120GB SSD, you will thus need to write 12000 Tera (12 peta) before it fails. It is clear to me that small things (like putting /var outside the SSD somehow) makes no sense. Even the swap makes me dubious: is it really worthwhile to try to spare the SSD, will it not become obsolete well before it dies. Because the SSD is faster, it could actually make sense to swap on it on an optimal way? SSD supports fast reading of nonadjacent data, which seems a big plus for the swap.
Edited: It seems that this page http://ef.gy/statistics:ssd-write-endurance go in my sense. You will need more that six months to wear a SSD if you write to it at the maximum possible rate 24h/24h. If that is true, the SSD will never fail unless you do it on purpose. I have no estimate how much data we write on a hard disk on average but I think it is only a tiny fraction of that...
# mod edit: please don't rollback edits that make your thread title more relevant to the actual question you are asking. "SSD disk" means fsck all...
Last edited by jasonwryan (2013-08-20 07:04:07)

I think it is highly dependent on what you are using your machine for, but yes, I too see very little swap use with 8GB RAM. In my experience, hibernation on linux (suspend to disk) is far from perfect, and has always cased me more issues than the functionality was worth.
Recently though, I was able to set up Intel Rapid Start Technology, which is like hibernation controlled by the firmware. Typically you would use it by setting a timeout in the bios. So after being suspended for that set period of time, it would power back up partially and write the contents do disk, then "hibernate". But as of 3.11 Matthew Garrett created a userspace driver for it, so I can set it to only function in the event that my battery gets super low (at what point it decides that I'm not quite sure).
If your machien supports IRST, you should be aware that because it is firmware controlled, you cannot get away with "hibernating" on an Intel Rapid Start Technology partition that is less than the size of your RAM. It does not compress or try to opitimize the RAM contents for size at all. Also, it must be used on an SSD, so it is likely going to be taking valuable space on the faster disk. Interstingly, gehidore has the same machine as me, yet IRST works great for me, yet not at all for him.

Bigger and faster hard disk for T61 Model 6458-CTO

6I would like to know which is the bigger and faster hard disk that i can buy for a T61 (6458-CTO).
It has a 80Gb hard disk, 5400 rpm and SATA interface (1.5 Gb/s).
Can i buy a SATA II (3 Gb/s, 500Gb and 7200rpm) for this computer?
Thank you.
Jon
Message Edited by jonaur on 07-12-2009 07:00 PM
Solved!
Go to Solution.

Thank you very much for the early information.
This forum works really fine.

PROBOOK and SAMSUNG SSD 850 EVO DISK problems

I have connected HP ProBook 470 G2 i7 processor with SAMSUNG SSD 850 EVO 500 GB via SATA3 to USB3 adapter (STLAB). SSD disk is not detected by windows 7 (win explorer) neither by samsung magition SW.
Is it possible to solve this.

Does the drive show in Disk Management?
Does it show as 'offline'? This sometimes happens with 'external' drives.
If it is 'offline' just right click 'offline' and chose 'online' from the menu.
Hope that helps.
If you found my answer helpful please say thanks by clicking on the Thumb's Up icon. Thanks!

Satellite U840W PSU5XA - Win 8.1 installation and effective SSD usage

Hello.
Im hoping for a solution to two issues.
The second I suspect is caused by the first.
Satellite U840W PSU5XA-001006
Started to receive BSOD with various faults.
Most persistant was IRQ LESS or not EQUAL- iaStorAV.sys
Many hours of searching and I cannot locate a solution nor post that actually has the "AV" extension on on iaStore.sys.....
So, i factory resetted, and various other issues (BSOD's) persisted.
So, I Clean installed Windows 8.1 straight over everything and deleted all previous files.
I noticed the system was not running any factory TOSHIBA Branded utilities etc. and seemed to be a lot slower. I suspected that this was caused due to the 32GB SSD used for Cache had now seemingly been bi-passed and everything was now strictly running off the 500GB HDD. I dont recall BSOD's but the system was significantly slower on boot and performance.
Sooooo, (SIGH), I again reset back to factory settings and this gave me back TOSHIBA branded utilities such as service station and the like.
HOWEVER, The BSOD's remained and once upgrading to windows 8.1 KEEPING files and settings, the iaStorAV.sys error has returned (specifically when closing lid into sleep mode) forcing CRITICAL error and forcing system into reboot instead of awakening from sleep.
Note: Windows is a legit MS copy so that isnt the issue either. Even stranger is that the 8.1 instal had been running at least 8 months no issue prior to sudden BSOD Page file and iaStorAV errors. Readings and posts have me believing MS Updates to bee the culprit here for the beginning of these issues.
I read a similar post regarding enabling RAID CACHE PRIOR to Windows 8.1 install. My intuition tells me that these two may just be related. i.e. If windows has not installed RAID CACHE properly, then CACHE isnt being strored correctly and causing BSOD's. Im a newbie at this stuff, so be patient.....
What I really want to know is, How can I now Factory Reset Windows 8, making positive the 32GB is being used as CACHE and assisting fastboot etc, then safely upgrade to Windows 8.1?
Any assistance would be greatly appreciated.
THINGS ALSO ATTEMPTED: IRST and RAID re-Install, Memory Diagnostic (Passed), BIOS Upgrade to 6.70, Rapid Storage Drivers re-installed
Thanks ahead of time,
Mr Frustrated............

Ok, well, its been a while and no-one had really come up with a solid solution. But thank you JakieStewart for the RST information.
Note: Updating RST drivers alone, failed....
However, I have been able to work around the issue in a way:
I have lost the ability to use the SSD as a cache, which really annoys me, as all the reboots, and suggestions i have read, re-installs etc proved flawed in some way or another.
So, I have instead chosen to clean install windows 8.1 then followed a post relating to Diskpart and setting SSD hibernation partition.
A link to consider would be http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf
However i followed a somewhat abbreviated version.
Conclusion:
1. Now I can close the lid on my U840W (INTO SLEEP or HIBERNATION Mode and not get a "System Thread Exception iaStorAV.sys error because I have 1. Reluctantly Clean Installed Windows 8.1 over factory image and 2. now created a >Hibernation Partition< on the SSD
Even though SSD Cache may no longer be available, creating this Hibernation Partition assists with Rapid START Technology and the associated iaStorAV.sys type errors
You can find your Toshiba Rapid Store Technology Drivers for your model here:
https://downloadcenter.intel.com/search?keyword=Intel%C2%AE+Rapid+Storage+Technolog y+%28Intel%C2%AE+RST%29
2. I no longer have the option to use the SSD as a cache, but overall my system runs a lot better now
3. The SSD is not visible in explorer (which it never was under the original settings anyway)
3. Downside: I can no longer boot or reset back to original Toshiba factory settings and can only recover from the new recovery disk (USB) i have made.
I have now also downloaded and stored on a USB all the original TOSHIBA U840W Drivers from http://www.mytoshiba.com.au/support/computers/ultrabook/u840w/psu5xa-001006/download?os=30
If like me, you clean install windows 8.1 I highly suggest getting your drivers downloaded locally so that you don't have to keep going back to Toshiba or Intel unless updates are required.
4. Note: Make note to set the BIOS Hibernation mode to "Immediately" if you choose to go this route as per the instructions on the Intel Link
5. Change "Toshiba Power Options" to make sure that closing Lid send laptop into Sleep or Hibernation (Both work) Do this by searching for "power options' in windows charm search and >select power plan >Change power plan settings >Change Advanced Power Settings >Power Button and Lid >selecting either Sleep or Hibernation (both work as i said earlier)
ON THE PRO SIDE: My HDD boot from total Shutdown State time is "about" 50 seconds but more significantly, closing the lid into sleep keeps my work available again, and takes 9.5 seconds to boot from sleep into usable actions!!!!
So despite losing SSD Cache, I now know a lot more about my computer, and the sleep function and Hibernation work supremely well.
I hope someone finds this thread useful...
Shane
Laslty, it is sooooo strange how this all happened overnight with the iaStora.sys; iaStorAV.sys iaStora.sys errors...and how restoring back to previous states didn't work, and how it seemingly corrupted even the Flash Stored Cache settings and Operating System! At least I now understand my computer better and luckily this didn't occur during previous Diploma studies. Phew.....
Message was edited by: shaner1

Setting up Dual Boot on a laptop with an HDD and an SSD?

Hello,
I've had a Lenovo Y500 laptop for about a year now, and I'd really like to run Arch on it. I've been using Arch on a virtual machine for a while now, and I have tried other distros like Gentoo and Slackware, but Arch is by far my favorite. I find myself spending most of my time on Arch with only 1GB RAM and 32GB hard disk space allocated, when I could be on my 8GB RAM Windows machine.
The laptop has a 1TB HDD which is split into two partitions, a 883GB C: drive(entitled Windows OS) and a 25GB D: drive (entitled Lenovo), and a 16GB SSD which I imagine is for cache. I think I would like to allocate 256GB for Arch, since I really don't need much space to run Arch.
Obviously I have to set up another partition, but I really don't know how to do that, especially without screwing up my HDD and SSD configuration.
Any tips would be greatly appreciated,
Thanks a lot

Ensure you have read https://wiki.archlinux.org/index.php/Partitioning
Gparted worked very well for me several years ago when I re-sized the (gack!) Vista partition that came on this laptop to make room for a real OS. I had no problems -- be advised that this is a BIOS machine. Be sure you back up anything important to you before you start.

Install Boot Camp/OS X on SSD disk, use internal harddrive for storing applications for Boot Camp

Hello everyone!
I have a SSD drive that I have installed Yosemite on and have the following question:
I have an iMac with an external SSD disk on 250 GB that I have connected in a thunderbolt enclosure and have an internal hard drive on 500 GB SATA drive.
First I wonder if it's possible to have a dual boot on OS X and Boot Camp on my SSD disk?
But here comes the tricky part. I want to have my internal hard drive (500 GB) on my iMac to use some sharing to Windows.
So my idea is just boot to Boot Camp and use my internal hard drive, that I want to partition to two parts (one partition for OS X and one partition for Windows) to have the applications (like games/user applications) installed on so I don't fill up my SSD drive with all that data. I just want to have the SSD disk to boot in and use the speed for the Boot Camp system.
I also have file vault activated on Yosemite and want to have encryption activated on both volumes (OS X/ Boot Camp) so it's secured.
So is this idea possible to do or do I need to have all the user applications / games installed directly to my Boot Camp partition?
Sorry for my grammar, hope you understand what I want to do. If not I will try to explain better and more detailed if needed.
Thanks so much in advanced!

Trendchaser wrote:
Hello everyone!
I have a SSD drive that I have installed Yosemite on and have the following question:
I have an iMac with an external SSD disk on 250 GB that I have connected in a thunderbolt enclosure and have an internal hard drive on 500 GB SATA drive.
First I wonder if it's possible to have a dual boot on OS X and Boot Camp on my SSD disk?
Please see http://bleeptobleep.blogspot.com/2013/02/mac-install-windows-7-or-8-on-external. html for installing on an external Thunderbolt disk.
But here comes the tricky part. I want to have my internal hard drive (500 GB) on my iMac to use some sharing to Windows.
So my idea is just boot to Boot Camp and use my internal hard drive, that I want to partition to two parts (one partition for OS X and one partition for Windows) to have the applications (like games/user applications) installed on so I don't fill up my SSD drive with all that data. I just want to have the SSD disk to boot in and use the speed for the Boot Camp system.
You can create a FAT/exFAT partition via Disk Utility on the 500GB SATA disk. After Windows is installed, format this partition to NTFS from Windows, and use it as Windows D: (or appropriate drive letter depending on your environment) and install Games/Applications. Be careful with the read-only HFS partitions which get drive letters assigned automatically. This partition cannot be resized using Windows tools or OSX Disk tools.
I also have file vault activated on Yosemite and want to have encryption activated on both volumes (OS X/ Boot Camp) so it's secured.
FV2 (and any other CoreStorage volumes) are unreadable in Windows. Only HFS+ volumes are supported by the Apple read-only HFS driver provided by BC drivers. Windows volumes require BitLocker encryption, FV2 cannot be used for such volumes.

A Kernel Panic and two Crashes since updating to 10.8.1

I've been running a 15" MacBook Pro (Mid 2009) for about a year and a half. It's factory stock (no hardware modifications) with a 2.8 Core 2 Duo processor and 4gig RAM with a 500GB HD. It came with 10.5 installed. I upgraded to 10.6, 10.7 & 10.8 respectively. Each time a new operating system came out, I did a clean install. My system has been 100% reliable up until I installed the 10.8.1 update. Since then, I've had a Kernel Panic and two separate crashes.
I doubt it's a hardware issue as it's never been suspect before. Also, I've run Disk Utility and verified the disk and permissions. No Problems there.
The first problem was the Kernel Panic, which occurred while I was in the guest account watching YouTube videos. The system went to a gray screen then gave me the typical "Panic" message and rebooted itself.
The second problem must have occurred while the computer was in sleep mode, as I don't recall any particular issue, but I found a CRASH log in the logs folder.
Finally, I encountered the most recent crash while I was exiting out of the ADMIN account on my computer. The system went to a gray screen with a rotating bezel indicator, and wouldn't return to the log-in screen. I had to manually cycle the power button in order for the computer to reboot.
I'm not sure what's going on.

Hi. Since updating to 10.8 I've had numerous kernel panics on start-up. A restart always worked successfully, but it's getting annoying. I started out by replacing the HD with an SSD. That didn't work. Then I resent the PRAM/NVRAM. That seemed to work. Then I upgraded to 10.8.1 - and we're back to kernel panics.
Here's the log, and below it are photos of the initial kernel panic. :
29/08/2012 10:30:58.000 bootlog[0]: BOOT_TIME 1346232658 0
29/08/2012 10:31:00.000 kernel[0]: Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
29/08/2012 10:31:00.000 kernel[0]: vm_page_bootstrap: 859948 free pages and 114900 wired pages
29/08/2012 10:31:00.000 kernel[0]: kext submap [0xffffff7f8073e000 - 0xffffff8000000000], kernel text [0xffffff8000200000 - 0xffffff800073e000]
29/08/2012 10:31:00.000 kernel[0]: zone leak detection enabled
29/08/2012 10:31:00.000 kernel[0]: standard timeslicing quantum is 10000 us
29/08/2012 10:31:00.000 kernel[0]: standard background quantum is 2500 us
29/08/2012 10:31:00.000 kernel[0]: mig_table_max_displ = 74
29/08/2012 10:31:00.000 kernel[0]: corecrypto kext started!
29/08/2012 10:31:00.000 kernel[0]: Running kernel space in FIPS MODE
29/08/2012 10:31:00.000 kernel[0]: Plist hmac value is    735d392b68241ef173d81097b1c8ce9ba283521626d1c973ac376838c466757d
29/08/2012 10:31:00.000 kernel[0]: Computed hmac value is 735d392b68241ef173d81097b1c8ce9ba283521626d1c973ac376838c466757d
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS integrity POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS AES CBC POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS TDES CBC POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS SHA POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS HMAC POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS ECDSA POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS DRBG POST test passed!
29/08/2012 10:31:00.000 kernel[0]: corecrypto.kext FIPS POST passed!
29/08/2012 10:31:00.000 kernel[0]: AppleACPICPU: ProcessorId=0 LocalApicId=0 Enabled
29/08/2012 10:31:00.000 kernel[0]: AppleACPICPU: ProcessorId=1 LocalApicId=1 Enabled
29/08/2012 10:31:00.000 kernel[0]: calling mpo_policy_init for TMSafetyNet
29/08/2012 10:31:00.000 kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
29/08/2012 10:31:00.000 kernel[0]: calling mpo_policy_init for Sandbox
29/08/2012 10:31:00.000 kernel[0]: Security policy loaded: Seatbelt sandbox policy (Sandbox)
29/08/2012 10:31:00.000 kernel[0]: calling mpo_policy_init for Quarantine
29/08/2012 10:31:00.000 kernel[0]: Security policy loaded: Quarantine policy (Quarantine)
29/08/2012 10:31:00.000 kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
29/08/2012 10:31:00.000 kernel[0]: The Regents of the University of California. All rights reserved.
29/08/2012 10:31:00.000 kernel[0]: MAC Framework successfully initialized
29/08/2012 10:31:00.000 kernel[0]: using 16384 buffer headers and 10240 cluster IO buffer headers
29/08/2012 10:31:00.000 kernel[0]: IOAPIC: Version 0x11 Vectors 64:87
29/08/2012 10:31:00.000 kernel[0]: ACPI: System State [S0 S3 S4 S5] (S3)
29/08/2012 10:31:00.000 kernel[0]: AppleIntelCPUPowerManagement: (built 23:03:24 Jun 24 2012) initialization complete
29/08/2012 10:31:00.000 kernel[0]: PFM64 (36 cpu) 0xf10000000, 0xf0000000
29/08/2012 10:31:00.000 kernel[0]: [ PCI configuration begin ]
29/08/2012 10:31:00.000 kernel[0]: console relocated to 0xf10010000
29/08/2012 10:31:00.000 kernel[0]: PCI configuration changed (bridge=2 device=1 cardbus=0)
29/08/2012 10:31:00.000 kernel[0]: [ PCI configuration end, bridges 5 devices 18 ]
29/08/2012 10:31:00.000 kernel[0]: NVEthernet::start - Built Jun 25 2012 17:20:40
29/08/2012 10:31:00.000 kernel[0]: mbinit: done [64 MB total pool size, (42/21) split]
29/08/2012 10:31:00.000 kernel[0]: Pthread support ABORTS when sync kernel primitives misused
29/08/2012 10:31:00.000 kernel[0]: rooting via boot-uuid from /chosen:
29/08/2012 10:31:00.000 kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
29/08/2012 10:31:00.000 kernel[0]: com.apple.AppleFSCompressionTypeZlib kmod start
29/08/2012 10:31:00.000 kernel[0]: com.apple.AppleFSCompressionTypeDataless kmod start
29/08/2012 10:31:00.000 kernel[0]: com.apple.AppleFSCompressionTypeZlib load succeeded
29/08/2012 10:31:00.000 kernel[0]: com.apple.AppleFSCompressionTypeDataless load succeeded
29/08/2012 10:31:00.000 kernel[0]: AppleIntelCPUPowerManagementClient: ready
29/08/2012 10:31:00.000 kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@B/AppleMCP79AHCI/PR T0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOBlockStorageD river/M4-CT512M4SSD2 Media/IOGUIDPartitionScheme/Aidan's SSD@2
29/08/2012 10:31:00.000 kernel[0]: BSD root: disk0s2, major 1, minor 2
29/08/2012 10:31:00.000 kernel[0]: Kernel is LP64
29/08/2012 10:31:00.000 kernel[0]: BTCOEXIST off
29/08/2012 10:31:00.000 kernel[0]: BRCM tunables:
29/08/2012 10:31:00.000 kernel[0]: pullmode[1] txringsize[ 256] reapmin[   32] reapcount[ 128]
29/08/2012 10:31:00.000 kernel[0]: highWaterMark: VO[ 192] VI[ 192] BE[ 192] BK[ 192]
29/08/2012 10:31:00.000 kernel[0]: FireWire (OHCI) Lucent ID 5901 built-in now active, GUID d49a20fffefbdb82; max speed s800.
29/08/2012 10:31:00.000 kernel[0]: USBMSC Identifier (non-unique): 000000009833 0x5ac 0x8403 0x9833
29/08/2012 10:30:58.141 com.apple.launchd[1]: *** launchd[1] has started up. ***
29/08/2012 10:30:58.141 com.apple.launchd[1]: *** Shutdown logging is enabled. ***
29/08/2012 10:30:59.971 com.apple.launchd[1]: (com.apple.automountd) Unknown key for boolean: NSSupportsSuddenTermination
29/08/2012 10:31:00.000 kernel[0]: NVEthernet: Ethernet address d4:9a:20:fb:db:82
29/08/2012 10:31:00.000 kernel[0]: AirPort_Brcm4331: Ethernet address 00:23:6c:96:cc:0e
29/08/2012 10:31:00.000 kernel[0]: IO80211Controller::dataLinkLayerAttachComplete(): adding AppleEFINVRAM notification
29/08/2012 10:31:00.000 kernel[0]: IO80211Interface::efiNVRAMPublished():
29/08/2012 10:31:01.891 airportd[27]: _processDLILEvent: en1 attached (down)
29/08/2012 10:31:02.000 kernel[0]: createVirtIf(): ifRole = 1
29/08/2012 10:31:02.000 kernel[0]: in func createVirtualInterface ifRole = 1
29/08/2012 10:31:02.000 kernel[0]: AirPort_Brcm4331_P2PInterface::init name <p2p0> role 1 this 0xffffff802049dc00
29/08/2012 10:31:02.000 kernel[0]: AirPort_Brcm4331_P2PInterface::init() <p2p> role 1
29/08/2012 10:31:02.000 kernel[0]: Created virtif 0xffffff802049dc00 p2p0
29/08/2012 10:31:02.229 com.apple.SecurityServer[17]: Session 100000 created
29/08/2012 10:31:02.000 kernel[0]: NVDANV50HAL loaded and registered.
29/08/2012 10:31:02.000 kernel[0]: [IOBluetoothHCIController][start] -- completed
29/08/2012 10:31:02.000 kernel[0]: IOBluetoothUSBDFU::probe
29/08/2012 10:31:02.000 kernel[0]: IOBluetoothUSBDFU::probe ProductID - 0x8213 FirmwareVersion - 0x0201
29/08/2012 10:31:02.000 kernel[0]: [BroadcomBluetoothHCIControllerUSBTransport][start] -- completed
29/08/2012 10:31:02.000 kernel[0]: [IOBluetoothHCIController][staticBluetoothHCIControllerTransportShowsUp] -- Received Bluetooth Controller register service notification
29/08/2012 10:31:02.000 kernel[0]: Previous Shutdown Cause: 3
29/08/2012 10:31:02.000 kernel[0]: [IOBluetoothHCIController::setConfigState] calling registerService
29/08/2012 10:31:02.282 com.apple.SecurityServer[17]: Entering service
29/08/2012 10:31:02.383 UserEventAgent[13]: Captive: [HandleNetworkInformationChanged:2435] nwi_state_copy returned NULL
29/08/2012 10:31:02.000 kernel[0]: AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
29/08/2012 10:31:02.000 kernel[0]: en1::IO80211Interface::postMessage bssid changed
29/08/2012 10:31:03.000 kernel[0]: DSMOS has arrived
29/08/2012 10:31:03.000 kernel[0]: macx_swapon SUCCESS
29/08/2012 10:31:03.051 hidd[56]: Posting 'com.apple.iokit.hid.displayStatus' notifyState=1
29/08/2012 10:31:03.075 appleeventsd[61]: main: Starting up
29/08/2012 10:31:03.105 mDNSResponder[49]: mDNSResponder mDNSResponder-379.27.1 (Aug 1 2012 20:12:04) starting OSXVers 12
29/08/2012 10:31:03.176 configd[19]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50)
29/08/2012 10:31:03.177 configd[19]: DHCP en1: INIT transmit failed
29/08/2012 10:31:03.202 loginwindow[52]: Login Window Application Started
29/08/2012 10:31:03.279 awacsd[65]: Starting awacsd connectivity-77 (Jun 20 2012 15:40:49)
29/08/2012 10:31:03.000 kernel[0]: 00000000 00000020 NVEthernet::setLinkStatus - not Active
29/08/2012 10:31:03.341 awacsd[65]: InnerStore CopyAllZones: no info in Dynamic Store
29/08/2012 10:31:03.363 mDNSResponder[49]: D2D_IPC: Loaded
29/08/2012 10:31:03.363 mDNSResponder[49]: D2DInitialize succeeded
29/08/2012 10:31:03.530 com.apple.usbmuxd[37]: usbmuxd-268.5 on Apr 5 2012 at 15:33:48, running 64 bit
29/08/2012 10:31:03.551 configd[19]: network changed: DNS*
29/08/2012 10:31:03.441 systemkeychain[70]: done file: /var/run/systemkeychaincheck.done
29/08/2012 10:31:03.563 configd[19]: setting hostname to "Aidan-Byrnes-Computer.local"
29/08/2012 10:31:03.646 locationd[53]: NOTICE,Location icon should now be in state 0
29/08/2012 10:31:03.674 mds[48]: (Normal) FMW: FMW 0 0
29/08/2012 10:31:03.676 WindowServer[86]: Server is starting up
29/08/2012 10:31:03.680 WindowServer[86]: Session 256 retained (2 references)
29/08/2012 10:31:03.680 WindowServer[86]: Session 256 released (1 references)
29/08/2012 10:31:03.703 WindowServer[86]: Session 256 retained (2 references)
29/08/2012 10:31:03.705 WindowServer[86]: init_page_flip: page flip mode is on
29/08/2012 10:31:03.779 coreservicesd[29]: FindBestLSSession(), no match for inSessionID 0xfffffffffffffffc auditTokenInfo( uid=0 euid=0 auSessionID=100000 create=false
29/08/2012 10:31:03.881 apsd[67]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
29/08/2012 10:31:03.882 apsd[67]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
29/08/2012 10:31:04.048 netbiosd[72]: Unable to start NetBIOS name service:
29/08/2012 10:31:04.249 WindowServer[86]: mux_initialize: Couldn't find any matches
29/08/2012 10:31:04.276 WindowServer[86]: GLCompositor enabled for tile size [256 x 256]
29/08/2012 10:31:04.276 WindowServer[86]: CGXGLInitMipMap: mip map mode is on
29/08/2012 10:31:04.311 WindowServer[86]: WSMachineUsesNewStyleMirroring: false
29/08/2012 10:31:04.312 WindowServer[86]: Display 0x04272240: GL mask 0x1; bounds (0, 0)[1280 x 800], 30 modes available
Main, Active, on-line, enabled, built-in, boot, Vendor 610, Model 9c89, S/N 0, Unit 0, Rotation 0
UUID
29/08/2012 10:31:04.312 WindowServer[86]: Display 0x003f003d: GL mask 0x2; bounds (0, 0)[0 x 0], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 1, Rotation 0
UUID 0xffffffffffffffffffffffff003f003d
29/08/2012 10:31:04.323 WindowServer[86]: Created shield window 0x5 for display 0x04272240
29/08/2012 10:31:04.324 WindowServer[86]: Created shield window 0x6 for display 0x003f003d
29/08/2012 10:31:04.331 WindowServer[86]: Display 0x04272240: GL mask 0x1; bounds (0, 0)[1280 x 800], 30 modes available
Main, Active, on-line, enabled, built-in, boot, Vendor 610, Model 9c89, S/N 0, Unit 0, Rotation 0
UUID
29/08/2012 10:31:04.331 WindowServer[86]: Display 0x003f003d: GL mask 0x2; bounds (2304, 0)[1 x 1], 1 modes available
off-line, enabled, Vendor ffffffff, Model ffffffff, S/N ffffffff, Unit 1, Rotation 0
UUID 0xffffffffffffffffffffffff003f003d
29/08/2012 10:31:04.331 WindowServer[86]: CGXPerformInitialDisplayConfiguration
29/08/2012 10:31:04.331 WindowServer[86]:   Display 0x04272240: MappedDisplay Unit 0; Vendor 0x610 Model 0x9c89 S/N 0 Dimensions 11.26 x 7.05; online enabled built-in, Bounds (0,0)[1280 x 800], Rotation 0, Resolution 1
29/08/2012 10:31:04.331 WindowServer[86]:   Display 0x003f003d: MappedDisplay Unit 1; Vendor 0xffffffff Model 0xffffffff S/N -1 Dimensions 0.00 x 0.00; offline enabled, Bounds (2304,0)[1 x 1], Rotation 0, Resolution 1
29/08/2012 10:31:04.000 kernel[0]: Ethernet [nvenet]: Link up on en0, 100-Megabit, Full-duplex, No flow-control, Debug [796d,0000,0de1,0005,41e1,0000]
29/08/2012 10:31:04.000 kernel[0]: 05f5e100 00100026 NVEthernet::setLinkStatus - Active
29/08/2012 10:31:04.000 kernel[0]: Ethernet [nvenet]: Link up on en0, 100-Megabit, Full-duplex, No flow-control, Debug [796d,0000,0de1,0005,41e1,0000]
29/08/2012 10:31:04.000 kernel[0]: 05f5e100 00100026 NVEthernet::setLinkStatus - Active
29/08/2012 10:31:04.449 WindowServer[86]: GLCompositor: GL renderer id 0x0102260e, GL mask 0x00000003, accelerator 0x00003863, unit 0, caps QEX|QGL|MIPMAP, vram 256 MB
29/08/2012 10:31:04.452 WindowServer[86]: GLCompositor: GL renderer id 0x0102260e, GL mask 0x00000003, texture units 8, texture max 8192, viewport max {8192, 8192}, extensions FPRG|NPOT|GLSL|FLOAT
29/08/2012 10:31:04.456 loginwindow[52]: **DMPROXY** Found `/System/Library/CoreServices/DMProxy'.
29/08/2012 10:31:04.469 hidd[56]: void __IOHIDLoadBundles(): Loaded 0 HID plugins
29/08/2012 10:31:04.517 WindowServer[86]: Unable to open IOHIDSystem (e00002bd)
29/08/2012 10:31:04.000 kernel[0]: virtual bool IOHIDEventSystemUserClient::initWithTask(task_t, void *, UInt32): Client task not privileged to open IOHIDSystem for mapping memory (e00002c1)
29/08/2012 10:31:04.608 WindowServer[86]: Created shield window 0x7 for display 0x04272240
29/08/2012 10:31:04.608 WindowServer[86]: Display 0x04272240: MappedDisplay Unit 0; ColorProfile { 2, "Color LCD"}; TransferTable (256, 3)
29/08/2012 10:31:04.662 com.apple.launchd[1]: (name.razzfazz.daemon.iScroll2[104]) Job failed to exec(3). Setting up event to tell us when to try again: 2: No such file or directory
29/08/2012 10:31:04.662 com.apple.launchd[1]: (name.razzfazz.daemon.iScroll2[104]) Job failed to exec(3) for weird reason: 2
29/08/2012 10:31:04.668 launchctl[97]: com.apple.findmymacmessenger: Already loaded
29/08/2012 10:31:04.730 com.apple.SecurityServer[17]: Session 100005 created
29/08/2012 10:31:04.770 hidd[56]: CGSShutdownServerConnections: Detaching application from window server
29/08/2012 10:31:04.770 hidd[56]: CGSDisplayServerShutdown: Detaching display subsystem from window server
29/08/2012 10:31:04.834 loginwindow[52]: Login Window Started Security Agent
29/08/2012 10:31:04.950 SecurityAgent[107]: This is the first run
29/08/2012 10:31:04.950 SecurityAgent[107]: MacBuddy was run = 0
29/08/2012 10:31:05.015 SecurityAgent[107]: User info context values set for aidanbyrne
29/08/2012 10:31:05.300 configd[19]: network changed: v4(en0+:134.220.228.104) DNS+ Proxy+ SMB
29/08/2012 10:31:05.331 root[114]: sntp sendpkt: sendto error: No route to host. Couldn't send packet!
29/08/2012 10:31:05.331 root[114]: on_wire failed for server 0.0.0.17!
29/08/2012 10:31:05.349 ntpd[34]: proto: precision = 1.000 usec
29/08/2012 10:31:05.493 loginwindow[52]: Login Window - Returned from Security Agent
29/08/2012 10:31:05.000 kernel[0]: [ffffff8021495800][BNBTrackpadDevice::init][75.15] init is complete
29/08/2012 10:31:05.522 loginwindow[52]: USER_PROCESS: 52 console
29/08/2012 10:31:05.604 com.apple.launchd.peruser.501[115]: (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
29/08/2012 10:31:05.609 loginwindow[52]: Connection with distnoted server was invalidated
29/08/2012 10:31:05.633 distnoted[118]: # distnote server agent absolute time: 7.965250809   civil time: Wed Aug 29 10:31:05 2012   pid: 118 uid: 501 root: no
29/08/2012 10:31:05.791 WindowServer[86]: **DMPROXY** (2) Found `/System/Library/CoreServices/DMProxy'.
29/08/2012 10:31:05.808 com.apple.SecurityServer[17]: Session 100006 created
29/08/2012 10:31:06.000 kernel[0]: [ffffff8021495800][BNBTrackpadDevice::handleStart][75.15] returning 1
29/08/2012 10:31:06.000 kernel[0]: [ffffff8021601c00][AppleMultitouchHIDEventDriver::start] entered
29/08/2012 10:31:06.000 kernel[0]: [ffffff80216af100][AppleMultitouchDevice::start] entered
29/08/2012 10:31:06.014 talagent[128]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:06.188 SystemUIServer[129]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:06.217 WindowServer[86]: Display 0x04272240: MappedDisplay Unit 0; ColorProfile { 2, "Color LCD"}; TransferTable (256, 3)
29/08/2012 10:31:06.323 configd[19]: setting hostname to "wxp-itr11564.unv.wlv.ac.uk"
29/08/2012 10:31:06.324 WindowServer[86]: **DMPROXY** (2) Found `/System/Library/CoreServices/DMProxy'.
29/08/2012 10:31:06.888 NetworkBrowserAgent[139]: Starting NetworkBrowserAgent
29/08/2012 10:31:07.016 Finder[130]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:07.142 WindowServer[86]: Display 0x04272240: MappedDisplay Unit 0; ColorProfile { 2, "Color LCD"}; TransferTable (256, 3)
29/08/2012 10:31:07.423 com.apple.launchd.peruser.501[115]: (name.razzfazz.daemon.iScroll2[157]) Exited with code: 2
29/08/2012 10:31:07.423 com.apple.launchd.peruser.501[115]: (name.razzfazz.daemon.iScroll2) Throttling respawn: Will start in 10 seconds
29/08/2012 10:31:07.000 kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=159[GoogleSoftwareUp] clearing CS_VALID
29/08/2012 10:31:07.527 loginwindow[52]: Login items - LSOpenApplication returned error -10665, url=/Library/CFMSupport/CNQL1212_ButtonManager.app
29/08/2012 10:31:07.527 loginwindow[52]: Unable to lauch startup item: (null)
29/08/2012 10:31:07.533 com.apple.launchd.peruser.501[115]: (com.apple.afpstat-qfa[156]) Exited with code: 2
29/08/2012 10:31:07.742 Folder Actions Dispatcher[160]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:07.788 loginwindow[52]: Login items - LSOpenApplication returned error -10665, url=/Applications/Microsoft AutoUpdate.app/Contents/MacOS/Microsoft AU Daemon.app
29/08/2012 10:31:07.788 loginwindow[52]: Unable to lauch startup item: (null)
29/08/2012 10:31:07.892 System Events[166]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:08.135 NotificationCenter[146]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:08.413 WindowServer[86]: Display 0x04272240: MappedDisplay Unit 0; ColorProfile { 2, "Color LCD"}; TransferTable (256, 3)
29/08/2012 10:31:08.506 coreaudiod[106]: 2012-08-29 10:31:08.505832 AM [AirPlay] Started browsing for _airplay._tcp.
29/08/2012 10:31:08.507 coreaudiod[106]: 2012-08-29 10:31:08.507315 AM [AirPlay] Started browsing for _raop._tcp.
29/08/2012 10:31:08.678 TISwitcher[168]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:08.736 com.apple.dock.extra[165]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:08.762 coreservicesd[29]: SendFlattenedData, got error #268435460 (ipc/send) timed out from ::mach_msg(), sending notification kLSNotifyApplicationReady to notificationID=129
29/08/2012 10:31:09.026 GoogleSoftwareUpdateAgent[159]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:09.102 SystemUIServer[129]: *** WARNING: -[NSImage compositeToPoint:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
29/08/2012 10:31:09.102 SystemUIServer[129]: *** WARNING: -[NSImage compositeToPoint:fromRect:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
29/08/2012 10:31:08.046 CCAAgent[163]: ****************************************
29/08/2012 10:31:08.047 CCAAgent[163]: **          CCA agent starts!         **
29/08/2012 10:31:08.047 CCAAgent[163]: ****************************************
29/08/2012 10:31:08.294 CCAAgent[163]: CCAAgent Logfiles: (/Users/aidanbyrne/Library/Application Support/Cisco Systems/CCAAgent/event.log) (/Users/aidanbyrne/Library/Application Support/Cisco Systems/CCAAgent/eventPrevious.log)
29/08/2012 10:31:08.458 DictationIM[178]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:08.844 BezelServices 235.55[52]: -[DriverServices sendPreferencesToDevice:resetDefaults:] error: classPrefID (null), classPrefs (null)
29/08/2012 10:31:09.170 CCAAgent[163]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:09.292 blued[64]: kBTXPCUpdateUserPreferences gConsoleUserUID = 501
29/08/2012 10:31:09.415 locationd[187]: NOTICE,Location icon should now be in state 0
29/08/2012 10:31:09.467 UserEventAgent[142]: cannot find fw daemon port 1102
29/08/2012 10:31:10.036 CoreLocationAgent[189]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:11.013 Dropbox[167]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:11.424 CalendarAgent[153]: -[SOAPParser:0x7fb0d8c971e0 parser:didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in SOAPDocument for html (html)
29/08/2012 10:31:11.431 LKDCHelper[198]: Starting (uid=501)
29/08/2012 10:31:11.458 CalendarAgent[153]: -[SOAPParser:0x7fb0d98b3560 parser:didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in SOAPDocument for html (html)
29/08/2012 10:31:11.459 CalendarAgent[153]: [com.apple.calendar.store.log.exchange.queue] [error = Error Domain=CalExchangeErrorDomain Code=-2 "Calendar can’t refresh the account “wlv.ac.uk”." UserInfo=0x7fb0d8c98230 {NSLocalizedFailureReason=The primary email address for the account can’t be found., CalFailedOperationKey=<CalExchangeSyncAccountOperation: 0x7fb0d9897830>, NSLocalizedDescription=Calendar can’t refresh the account “wlv.ac.uk”.}]
29/08/2012 10:31:11.495 CalendarAgent[153]: -[SOAPParser:0x7fb0d98f9e70 parser:didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in SOAPDocument for html (html)
29/08/2012 10:31:11.498 CalendarAgent[153]: [com.apple.calendar.store.log.exchange.queue] [error = Error Domain=CalExchangeErrorDomain Code=-2 "Calendar can’t refresh the account “wlv.ac.uk”." UserInfo=0x7fb0d8cea360 {NSLocalizedFailureReason=The primary email address for the account can’t be found., CalFailedOperationKey=<CalExchangeSyncAccountOperation: 0x7fb0d9897830>, NSLocalizedDescription=Calendar can’t refresh the account “wlv.ac.uk”.}]
29/08/2012 10:31:14.284 Image Capture Extension[214]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:14.316 CIJScannerRegister[215]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:15.303 com.apple.launchd.peruser.501[115]: (name.razzfazz.daemon.iScroll2[218]) Job failed to exec(3). Setting up event to tell us when to try again: 2: No such file or directory
29/08/2012 10:31:15.303 com.apple.launchd.peruser.501[115]: (name.razzfazz.daemon.iScroll2[218]) Job failed to exec(3) for weird reason: 2
29/08/2012 10:31:16.224 awacsd[65]: Exiting
29/08/2012 10:31:23.456 com.apple.launchd[1]: (com.apple.coreservices.appleid.authentication[103]) Exit timeout elapsed (20 seconds). Killing
29/08/2012 10:31:31.525 com.apple.SecurityServer[17]: Session 100002 created
29/08/2012 10:31:36.000 kernel[0]: Sandbox: sandboxd(232) deny mach-lookup com.apple.coresymbolicationd
29/08/2012 10:31:37.404 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-data /Library/Audio/Plug-Ins/Components/CamelCrusher.component
29/08/2012 10:31:37.409 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelCrusher.component/Contents
29/08/2012 10:31:37.414 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelCrusher.component
29/08/2012 10:31:37.419 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-data /Library/Audio/Plug-Ins/Components/CamelPhat.component
29/08/2012 10:31:37.424 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelPhat.component/Contents
29/08/2012 10:31:37.428 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelPhat.component
29/08/2012 10:31:37.433 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-data /Library/Audio/Plug-Ins/Components/CamelSpace.component
29/08/2012 10:31:37.438 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelSpace.component/Contents
29/08/2012 10:31:37.442 sandboxd[232]: ([106]) coreaudiod(106) deny file-read-metadata /Library/Audio/Plug-Ins/Components/CamelSpace.component
29/08/2012 10:31:47.300 Safari[242]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:47.327 WebProcess[244]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:31:50.474 PluginProcess[247]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:32:03.134 Safari[242]: CGContextClipToRect: invalid context 0x0
29/08/2012 10:32:03.539 WebProcess[250]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:38:22.299 Dock[127]: no information back from LS about running process
29/08/2012 10:38:22.373 Console[341]: Can't open input server /Library/InputManagers/Menu Extra Enabler.bundle
29/08/2012 10:41:22.416 com.apple.launchd.peruser.501[115]: (com.apple.KerberosHelper.LKDCHelper[198]) Exited with code: 1

T61 and two SSD disks

Similar Messages

Maybe you are looking for