T61 BIOS update locks up unit; will not boot

I attempted to download and install (properly, in accordance with instructions) the latest BIOS update. The computer froze during the BIOS update process. It will not boot. This is the 2nd time the identical problem occured. (unit went in for repair in 5/08 the first time) The unit will not boot from the DVD reader. I cannot the repair CD nor can I load a BIOS CD. Suggestions?

Welcome to the forum!
I certainly hope that you have warranty leftover, otherwise you're likely looking at out-of-pocket system board replacement.
Good luck
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Similar Messages

I have a Macbook pro 4,1 My Battery would not charge after only 23 cycles. I tried the battery update now my macbook will not boot. it has a kernel panic Unable to find driver for this platform:

Macbook 4,1
Early 2008 15" macbook pro
Running Snow Leopard
the Battery was not working after only 23 cycles
I tried the Battery update and now it will not boot at all
I really do not want to loose my data on the drive
panic message is
Unable to find driver for this platform: "ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Please help

Panic Message
panic(cpu 0 caller 0x000x563ebd) : Unable to find driver for this platform:
"ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Debugger called: <panic>
Backtrace (CPU 0), Format - Frame : Return Address (4 potential args on stack)
(7 lines of hex)
BSD Process name corresponding to current thread: Unkonwn
Kernel version:
Darwin Kernel Version 10.8.0" todays date ; root:xnu-1504.15.3~1/release_I386
I tried to boot from CD can, but i dont want to loose any information.
Tried disk tools
Hardware test
Tried to check if it was memory sticks failing or battery , nothing else plugged in
if i boot holding Apple key and S
I get additional warnings about AppleACPIPlatform and not being able to load Kext

After updating Airport software, Macbook will not boot

I see others have updated with the new Airport software without incident, but not me.
I just ran software update to install the Airport update (hoping it would cure the problem I've had -- and other users as well -- with the connection dropping every 5 minutes with Linksys routers [check the Airport discussion board for much discussion of this]).
After installing, upon restart my Macbook will not boot fully. I get the Apple symbol, then the spinning gear symbol, then a light blue screen and that's it. After a while the fan comes on.
Call it the light blue screen of death.
All was working fine until the update.
I have boot camp and I can boot into Windows.
I have tried removing the battery and resetting the PRAM. No help.
Sigh... Applecare is closed so I cannot call until Friday morning. Anyone have any suggestions of what I can try?
I have my Mac hard disk backed up from a few days ago using Super Duper on a USB drive but I am reluctant to try booting from it as I fear corrupting the drive. Unfortunately I don't have my Mac system CDs with me as I am away from home at the moment.
I just switched to the Mac 6 weeks ago after 3.5 years with a Dell laptop. Never had a single problem like this in all that time. But I still like my Mac.
PD

Well, I spoke too soon. Last night I was able to start up as described above, but this morning when I tried to start it did not even get to the Mac symbol. It just hung at a dark blue screen for several minutes.
Tried restarting with the shift key held down but it would not go into safe mode. Just the dark blue screen.
Resetting PRAM made it startup.
But I'm pretty nervous about this.
So, is there a way in Mac OS X to roll back to the system before the update? In Windows XP this is very simple under System Restore. I have the impression OS X doesn't have this feature and won't until next year with Time Machine.
And I see now I'm not the only user with this problem.
PD

After latest Mavericks update my MacBook Pro will not boot up

After using software update, I believe it said it was a security update. My laptop will not progress past a screen that says " Setting up your Mac...". I have tried holding down the power to restart but it always stops at the same place. I am using a MacBook Pro (17-inch Early 2009) running mavericks.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Bad update 10.10.2 will not boot

After installing 10.10.2 security update, computer boots to gray screen with Apple logo & progress bar that stops 2/3 of the way. I've logged into recovery & re-installed the OS & still doesn't work.
Im almost positive I don't have a bad HD after looking through all the posts with the same issue. I'm willing to do anything I can to retain my data. I've learned my lesson, but I need a solution.
What can I do?
Would this work:
Hook up an external drive & clone the internal drive to the external with disc utility.
Remove the internal drive & install the external
Re-install OS
Would this work? Or what should I do?
thanks,
matt

Your download or install may have been corrupted. Try to boot into the Recovery Partition and reinstall OS X from there and then re-boot. Another option is to attempt to boot into Safe Mode, see if your computer will do that.
Recovery Partition is Command + R on startup
Safe Boot is hold down Shift key on startup

Changed Mac HD to NO ACCESS for EVERYBODY now I'm locked out and will not boot

HELP...I Imagine I need to enter somehow as root. and change the permissions; however, I'm limited to the OS X startup screen and OS X Utilities right now so a quick response would be appreciated.

This is the first route I took before coming here-tried both repairing permissions and repairing HD using DU....No AVAIL...I get the first screen with Dark Apple and spinning lines in circle beneath, which then goes to an all blank screen where I am stuck: just a grey screen with my cursor arrow (which I can move, but there is nothing to select)...Basically in Mac **** right now as my backups are not doing well...the TWO EXTERNAL 1.5 TB DRIVES WERE BOTH DROPPED INDEPENDENTLY BY MY WIFE AND HER MOTHER AS THEY WERE REARRANGING THINGS IN OUR HOUSE...NOW I HAVE A CRAPPY TM BACKUP FROM AUGUST THAT I WILL ONLY USE AS A VERY LAST RESORT, IT SIMPLY ISNT COMPREHENSIVE ENOUGH TO COVER THE 500GB OF APPS AND DATA I USE NEARLY EVERY DAY IN SOME WAY SHAPE OR FORM. ANY HELP (AND THE QUICKER THE BETTER AS I HAVE COURT FILINGS ON THAT MAC AS WELL THAT I NEED TO HAVE ACCESS TO W/I THE NEXT 4 HOURS). AND YOU MAY JUST SAVE A MARRIAGE IN THE PROCESS!

X240 will not boot after latest bios update

I bought windows 8 .1 machine from factory. Then I had local shop install 8.1 on larger ssd. I just performed latest bios update and now machine will not boot. I am sure this is uefi related but I am not knowledgable in that area. The boot parameter returned to me by the shop was "legacy only" and secure boot was disabled.
Solved!
Go to Solution.

StanFan wrote:
I bought windows 8 .1 machine from factory. Then I had local shop install 8.1 on larger ssd. I just performed latest bios update and now machine will not boot. I am sure this is uefi related but I am not knowledgable in that area. The boot parameter returned to me by the shop was "legacy only" and secure boot was disabled.
Since doing the BIOS update are the settings still as you noted above? You also didn't mention which SSD is now installed in the system.
Just as an aside, installing Windows 8.1 in legacy mode isn't exactly optimal. Were there any particular reasons for this? Just being curious.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

BIOS update, then will not boot from any drive

This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
Downloaded Bios Version 63ET62WW and flashed it into the bios.
Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
It will also "see" a usb installed, but will not boot from it.
I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results.
HELP!! I should have never messed with it......

hi k4pew,
One rule after a BIOS update is to Load optimize deafults after updating.
Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
If not
Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
If still the same Im afraid that the BIOS needs to be reflashed.
Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
You can try calling Lenovo Technical Support for any options available for repair.
Im sorry to hear what happened
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Satellite Pro L300 will not boot after Bios update

Help please.
I have just formated a Satellite Pro L300 laptop.
I used all the updated drivers from Toshiba and all went very well.
I then updated the bios with the latest version.
After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
Any ides welcome

Hi
I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

After bios update, will not boot, says install an operating system

I have a amd hp 2000 notebook. i replaced the hard drive with an ss drive, windows 7. been working fine until the bios update, I bleieve, which lost the boot up parameters. how do I get it to boot. hard drive works well in another system so not that. getting the usual message, boot dvice not found, install an operating system, F2 diagnostics all pass. Hard disk (3F0) message
should one revert to earlier bios, usually not recommended. bios version 45 it says, so not sure the latest.

jwess wrote:
I have a amd hp 2000 notebook. i replaced the hard drive with an ss drive, windows 7. been working fine until the bios update, I bleieve, which lost the boot up parameters. how do I get it to boot. hard drive works well in another system so not that. getting the usual message, boot dvice not found, install an operating system, F2 diagnostics all pass. Hard disk (3F0) message
should one revert to earlier bios, usually not recommended. bios version 45 it says, so not sure the latest.

T61 BIOS Update

I have a 101 question on T61 BIOS Update:
My current version of BIOS is 2.25 (2008-11-14). In Lenovo site there are 3 or 4 updates available. Will I be able to jump to the latest available BIOS update or do I have to install all the BIOS updates in order?
Is it possible to backup BIOS before update, just in case if something goes wrong to restore BIOS?
Thank you!

You can install the latest, no need to do multiple. The process will make a backup of your old bios, but if the flash fails your computer won't be usable and there would be no simple way to recover. The standard procedure is to replace the system board and unless it's a very rare board, that would be the best option.
In my opinion it's not a good idea to update your bios unless you have something significant to gain, and do so at your own risk if the computer is out of warranty.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)

I have a 3rd generation iPad running iOS7.0.2, and since updating to iOS7, it will not mirror to an AppleTV. The devices will connect, but the video monitors show only a blank screen. The AppleTV's work fine with various other iOS & OSX devices. Ideas?

I have three AppleTV's where I work. I have two at home. I have an iPhone 4S running iOS7.0.2 which mirrors smoothly via AirPlay. I have a 2011 MacBook Pro and a 2011 iMac, both running Mountain Lion, both of which mirror smoothly through AirPlay. I have a 3rd generation iPad running iOS7.0.2, and since updating to iOS7, it will not mirror. The iPad will connect to the AppleTV, but the TV's and projectors only show a black screen when connected: the iPad screen looks as it should, except that the transitions become jumpy when connected via AirPlay. This is true on both networks: at home and at work. Another gentleman using the network where I work has the most recent iPad, also running iOS7.0.2, and he is having the same problem. I have tried to "Reset All Settings." I have tried to "Restore." Does anyone have any suggestions? Has anyone else experience difficulty mirroring the iPad through AirPlay since the release of iOS7.0.2?

No problems exists with the router (on either network described above) or the multiple AppleTV's which are able to mirror multiple other OSX & iOS devices seamlessly. The problem is strictly with the iPad and iOS7.
The following information was helpful:
Big Apple fan
Re: AirPlay with AirServer connectivity problem
Oct 14, 2013 9:43 AM (in response to ceb2652)
This is an iOS 7 AirPlay mirroring bug...
To make matters worse, the iPad automatically drops its mirroring session 45 seconds after it auto-locks.
3-4 mirroring sessions is all it takes for the iPad mirroring to freeze up.
After this happens, mirroring to an Apple TV only projects a blank screen.
Once the mirroring is hung, the only way to fix it is to restart the iPad.
Apple please fix this iOS 7 issue!

Ever since I updated iTunes my iPods will not sync with my cars

Ever since I updated iTunes my iPods will not sync with my cars.I have a 30g and 60g 5th gen iPods that I use in my two car. In my cars I have a dealer installed integration module so that I can navigate my I pods play list artist and song titles using the radio itself. Ever since that last iTunes update 7.3.1. I no longer am able to use this feature. I used my sister’s 30g iPod that she did has not updated and the system works fine. Can someone help me with this problem.

I have had an Alpine head unit in my car with the ipod connection for about a year and it has worked fine until recently. Now I get an error message on the ipod that reads, "The currently attached accessory is not supported by this ipod." I have tried connecting a buddy's ipod to my car stereo, and his still works fine with it. I've done the 5 R's, tried going back to an older version of itunes as Alpine suggested. My next step will be going to the Apple store with an appointment, seeing what they say.

Ever since I updated iTunes my iPods will not sink with my cars

Ever since I updated iTunes my iPods will not sink with my cars.I have a 30g and 60g 5th gen iPods that I use in my two car. In my cars I have a dealer installed integration module so that I can navigate my I pods play list artist and song titles using the radio itself. Ever since that last iTunes update 7.3.1. I no longer am able to use this feature. I used my sister’s 30g iPod that she did has not updated and the system works fine. Can someone help me with this problem.

I have had an Alpine head unit in my car with the ipod connection for about a year and it has worked fine until recently. Now I get an error message on the ipod that reads, "The currently attached accessory is not supported by this ipod." I have tried connecting a buddy's ipod to my car stereo, and his still works fine with it. I've done the 5 R's, tried going back to an older version of itunes as Alpine suggested. My next step will be going to the Apple store with an appointment, seeing what they say.

T61 will not boot with nvidia quadro 140m driver

Hi all,
A couple of weeks ago, after allowing MS update to install some FTDI driver updates, my system will not boot up and hangs shortly after the initial vista loading screen. The screen goes black with some HD activity and eventually reboots. After trying a couple of restore points with no luck, I started to remove the latest driver updates and other software to my system again with no luck.
If I uninstall the nvidia driver and use the Standard VGA driver, it will boot and come up properly. I've done a bunch of web searches and searches on this site and can't find my exact circumstances. Its hard to believe that it could be a hardware issue since it started after a software update, but since it hasn't been a problem for anyone else, I'm just not sure at this point.
I've tried earlier versions of the nvidia driver, removing other drivers and services trying to find a coincidence, but nothing seems to work. I'm kind of at a loss at this point. Does anyone have some suggestions?
Thanks in advance,
Dave

More info on my system:
OS Name    Microsoft® Windows Vista™ Business
Version    6.0.6001 Service Pack 1 Build 6001
System Model    6459CTO
System Type    x64-based PC
Processor    Intel(R) Core(TM)2 Duo CPU     T8300 @ 2.40GHz, 2401 Mhz, 2 Core(s), 2 Logical Processor(s)
BIOS Version/Date    LENOVO 7LETC5WW (2.25 ), 11/14/2008
SMBIOS Version    2.4
Installed Physical Memory (RAM)    4.00 GB
Also, does anyone know if using the Standard VGA Display driver without problems on this system means that the video card hardware is working? In other words, I'm trying to rule out a hardware problem with my nvidia quadro 140m card, so if the system works fine with the standard vga driver, would that mean the hardware on the card is ok?
Thanks,
Dave

T61 BIOS update locks up unit; will not boot

Similar Messages

Maybe you are looking for