T61P BSOD when docking with Advanced Port Replicator

Seems that I'm seeing more and more BSOD when hot docking my T61p running Windows Vista.  Machine is on and I dock and get BSOD.  Any ideas?  This was working fine for a while, I'm not sure what changed

Thanks... that's interesting...
So this Dynadocking station looks good (unless someone can point me to potential drawbacks). It leads me to believe that I can ditch the idea of buying a new Toshiba laptop and actually buy another brand and use the new laptop and my old M5 with the same Dynadocking station.
In that case, my remainder question is: I have internal drives that I swap in/out both my M3 and my M5. *Has the internal hard drive interface changed as well with the M9?*
Cheers
Daniel

Similar Messages

  • Potege S100: Advanced Port Replicator/Docking Station

    I need to know which docking station to use please.
    Advanced Port Replicator III Docking Station
    Will this one work?

    Hello Andrew
    I found some nice infos about the unit which is compatible with your Portege S100.
    Check this link:
    http://www.costcentral.com/proddetail/Toshiba_Advanced_Port_Replicator_III/PA3314U1PRP/C90140/
    Hope, I could help
    Bye

  • Need Advanced Port Replicator III drivers to use it with my Portege M300

    Hi,
    I have a Portege M300 with an Advanced Port Replicator III. I've had to reinstall the operating system and now can't find any drivers for the port replicator.
    Can anyone help me out? I'm running Win XP
    thanks

    Hi
    I assume you need drivers for the XP OS. Am I right???
    On the Toshiba driver page you will find all necessary drivers and utilities for Portg M300.
    There you will find also the installation instruction document. This document shows the right installation order.
    You should simply download all drivers and follow the installation order. Thats all

  • Is Advanced Port Replicator III plus compatible with Portege R200

    I just ordered a new Portege R200 and the above port-replicator... however, I note that the R200 isn't listed in the supported notebooks list for that replicator! Can anyone confirm if I have made a mistake and need to change the order?
    Will

    I have visited the Options & Accessories area on the Toshiba European site and as you already said the Portg R200 is not listed in the list of compatible notebooks.
    So I presume the Advanced Port Replicator III plus (PA3474E-1PRP) does not support the Protg R series.

  • Hi speed USB via an Advanced Port Replicator for a Tecra 9100?

    I have the same issue with a Tecra 9100 and upgrading it to hi speed USB as an earlier post where the suggested solution was to use a PCMCIA card.
    (see link: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=24103)
    I had an idea but i don't know if it will work and need some advice?????
    Can you buy an Advanced Port Replicator that has Hi Speed USB 2.0 ports on it (like the APR II PA3082U which works with the Tecra 9100) instead of the PCMCIA card.
    If the Port Replicator docks into the motherboard will it give you Hi Speed USB 2.0 or is the Tecra 9100 constrained to USB 1.1 via the hardware within the laptop itself and the port replicator won't help?
    Also if I go down the Port Replicator route do i need any drivers for the Hi speed ports of the Port Replicator to work on the Tecra 9100?
    Or to ask the question another way - what does the PCMIA USB 2.0 card have in it that the Advanced Port Replicator with hi speeed USB doesn't have?
    Many thanks in advance

    Hi there,
    the Tecra 9100 has NO usb 2.0 and thats a fact. Since the port replicator has these USB 2.0 ports does not mean that your machine, when docked to the Portrep, is able to handle USB 2.0 devices. The portrep is just like an usb-hub and behaves like. So if your machine doesnt have it then thats it.
    And the explanation to the PCMCIA/Cardbus solution:
    The pcmcia card has USB 2.0 Chipset, thats the reason why it IS a USB 2.0 device (roothub).
    I hope that was clear for you :)
    Just purchase that card and you will have USB 2.0
    Greets

  • Advanced Port Replicator III Plus Driver/Frimware

    Hi,
    I am having a number of problems with my Poretege M300 on Advanced Port Replicator III Plus. Some Fn keys aren't working and I'm not able to get the correct screen display on my external monitor.
    Question: are there drivers for the Port replicator? I don't have a CD or any other installation media.
    Thanks, Richard

    Pedro,
    Thanks for this.
    I have reinstalled the Common Modules and now when I undock the Fn F5 key works K to toggle between screens. I guess this is disabled when docked?
    But I still can't use the Toshiba Assist and Presentation buttons, although I have also reinstalled the drivers for these as well.
    The M300 supports the external screen resolution OK, but I have to re-arrange my desktop every time I dock and use the higehr resolution external screen.
    Richard

  • Where can I download a user manual for Advanced Port Replicator III plus

    Where can I download a user manual for this?
    I have searched the download manuals section but cannot find a reference to this.
    Thanks for any help

    Seems this manual is not available in the Toshiba user manual page.
    But usually you should receive a user manual together with the Advanced Port Replicator III plus.

  • Why does iPad 3 4G constantly restart after 8.3 update only when docked with iMac?

    Why does iPad 3 4G constantly restart after 8.3 update only when docked with iMac?

    That question is impossible to answer without more information. What troubleshooting steps have you performed? Did you try using another cable? Did you try using another USB port on the Mac? Did you reboot the Mac and reset the iPad? Have you tired restoring the iPad?
    Restart or reset your iPhone, iPad, or iPod touch - Apple Support
    Use iTunes to restore your iPhone, iPad, or iPod to factory settings - Apple Support

  • Video issues with USB port replicator with Digital Video

    I have a T400 running Windows XP SP3 32-bit, with the graphics mode set to use the ATI video card. I'm also using the latest approved Lenovo ATI driver for this machine.
    I have two issues, one of which I consider major:
    1) Sometimes when I plug in the replicator (got the latest drivers off of the Lenovo download site) everything works great, and other times the monitor never powers up. I plug the replicator into my laptop and the external keyboard and mouse work and the port replicator system tray icon appears, but the monitor is still in power-saving mode. If I try to activate the monitor by "extending" or "mirroring" it, it comes up with a pop-up that says:
    "ThinkPad USB port rep. device: Error" - "Fail when adding device instance into driver!"
    2) This is more of an annoyance, but I noticed when the monitor does work that black areas of the screen end up getting sparkly green lines through them. They aren't "actually there" in the sense that it's not corruption from the computer, they are simply artifacts of what seems to be some signalling problem.
    Any help is greatly appreciated.

    wim1234 wrote:
    We (DispkayLink) have tested office 2013 and not found any BSODs so there must be something system specific.
    Could you gather the system logs and post here so we can see what might be wrong? Details on how to do this are here:
    http://kb.displaylink.com/269
    Thanks
    Wim
    Your reply is 2 months later, I had to revert to Office 2010 and return the laptop to the end user.
    But, I got another model of the same laptop right now which can be used to test it, I will let you know if it works out this time with the lates DisplayLink software for Windows.

  • W510 Docked in 433820U Port Replicator USB Ports Occassiona​lly Stop Working

    Has anyone had the problem where the USB ports on the 433820U Port Replicator stop working? I've had it happen on several occassion where the USB ports on the port replicator stop working when I do something seemingly unrelated (e.g. unplugging a CAT5 network cable, dropping something on the desk near the docked laptop). Once this happens, I have to unplug the USB devices from the port replicator and plug them into the laptop's USB ports in order to continue using the keyboard or mouse, or turn the laptop off and then back on. I'm trying to figure out if this is a defect in the port replicator or some outdated driver. Anyone else have a similar problem?

     This system supports USB3 ports but they are only USB2 on the port replicator. What's up with that?
    Hi William:
    I kinda, sorta think that the reason that the USB connectors on the Dock are only USB2 has to do with the speed of the connection between the big dock connector on the bottom of the notebook and the USB ports on the back of the Dock.
    I notice a similar problem when I had a W500 and a earlier model Dock.  That earlier model dock had an UltraBay in it.  If I put a hard drive (installed in a caddy) in the Dock, it ran very slowly - as if it was connected by USB - but if I put the same hard drive in the same caddy into the UltraBay on the side of the W500, it ran very, very fast.  So, all I could attribute this to was that the data just could not flow through the dock connector on the bottom of the notebook as fast as it could flow through the UltraBay connector on the inside of the notebook.
    Perhaps the same concept applies to the USB connectors on the Dock... maybe the USB3 connectors on the notebook itself have a faster data connection into the computer than the USB connectors on the dock, which need to pass through that big dock connector on their way to the computer.
    Michael
    W520 (4270 CTO), which replaced a W500 (4062-27U), which replaced a T42P, which replaced an A21P...

  • Portege R700-14J - Compatible with Express Port Replicator II?

    Today I received my TOSHIBA Express Port Replicator II (PA3680E-1PRP) to be used with my TOSHIBA Portege R700-14J (PT311E-023006DU). I seem to be unable to fit the notebook easily into the docking station.
    Please let me knwo whether this port replicator docking station is *the right model* for the Portege R700-14J.
    Thank you
    Bert van Loon

    Hi mostlymedia,
    I have a little bit searched using Google and I found that Port Replicator II is compatible with Portg M750 and Tecra A/M/R/S Series but no information about Portege R700 :(
    In my opinion you should ask the ASP in your country if its the correct part or not before you do something wrong.

  • Advanced Port Replicator for TE2000 Notebook

    I have just bought a s/hand TE2000. Can anyone please tell me which model APR I should buy to go with it? Thanks

    Hi
    I have found the same info. Under options for this model there is listed Port Replicator with part number PA3082U/E-1PRP.

  • Satellite A60 - BSOD when surfing with wireless PCMCIA card

    Hello i used to browse internet with a wireless cardbus WL-54-CB (ADVANCE) on my Satellite A60-120 running windows xp sp2.
    I was working well until i decided to clean my computer which was slowed down by viruses.I use Ad-aware and Kaspersky and updated patches on wndowsupdate.Now the PC is clean but i have problems with the PCMICA card, when i launch IE i surf for one minute and windows crashe BSOD !
    It displays :
    STOP 0x00000001 (0xFE570000,0x00000002,0x00000001,0x819587DE)
    Any ideas to fix it ?
    Thanks.

    Cmon Guys... Stop that Toshiba Recovery Disk madness... Its no use... The Recovery Disk is as old as your laptop.. maybe older... The whole bunch of drivers in there are old... Its no use... Look.. For example if you have an Nvidia graphic Chip, you have to install the newest Nvidia driver... Prefer using the Nvidia driver, never the driver from Toshiba... And besides... It is always better to install the system manually...
    Back to the question... Since you had a virus I would recommend to reinstall your OS, even you think its clean... To solve your problem...
    deinstall the wireless card driver
    deinstall the PCMCIA driver and install the newest driver. Write down the Model and some other infos before deinstalling it :) ...
    reinstall the wlan crad driver...
    test it :)
    I always recommend to make a system backup every month... So if things go wrong... Just restore the backup... and everything is fine again... :)

  • X300 with Distorted Video With USB Port Replicator

    I have 2 X300s using the enhanced port replicators. The video on these two machines were fine for the last 2 months until last week. The video is distorted while connected to the VGA port on the replicator, but fine when connected to the onboard video. I replaced the port replicators and that seem to resolve the issue for day but the distorted video came back. Has anyone encountered this and is there fix? Both machines are on XP.

    Hello Rudi,
    Thank you so much for the reply.
    We tried today another T440 laptop with 64bit OS and as mentioned by you, we figured out that the conflict is happening between Intel Graphics 4400 driver with USB replicator.
    When I done an uninstallation of the updated Intel Graphics and the USB replicator works fine.
    As the laptop will be provided to HOD, so we will be going for a purchase of a replicator with good compatibility with 64 OS and intel video card.
    Appreciate your reply.
    Good day ahead.

  • IPhone cannot play music on computer when docked with iTunes

    Hey all,
    This is really troubling. I cannot play music on my iPhone through my computer in Windows via my iTunes.
    My home iTunes computer is MacOSX on the same computer. All of my work programs are in Windows Bootcamp. So in Windows mode, the songs appear to be gray, and cannot be clicked on (in iTunes and only on the iPhone). They are certainly locked. If I click on 'Manage Music Manually', a popup shows up asking me if I want to erase the iPhone and sync with the Windows itunes, which would be grim as all my music, videos, and everything is in MacOSX.
    I have been to the MacStore about this and they couldnt figure this out either. They think it might be a faulty phone.
    Has anyone heard of this and might know of a fix?
    Bill

    The iPhone won't play music through a computer's iTunes.
    You can use this cord http://store.apple.com/us/product/TN778LL/A?fnode=MTY1NDAzOQ&mco=MjE1NTkyMQ to connect the headset jack to the computer's audio-in port.

Maybe you are looking for

  • JDBC Adapter Error to conect to SQL Server 2005

    Hi all. I´m trying to conect to a SQL Server 2005 database, but facing this error: UnsupportedClassVersionError: (com/microsoft/sqlserver/jdbc/SQLServerDriver) bad major version at offset=6' The parameters are: JDBC Driver: com.microsoft.sqlserver.jd

  • Client/server program: Urgent, pls help!!

    I am new to Java, particularly Networking in Java, while writing client/server application I have got completely strucked now. Can any one give me an idea where I am wrong? I am writing a simple client server application in Java using Socket and Serv

  • ArrayCollection as Data Provider in Tree

    Hi,      Does anybody know how to use ArrayCollection as a data provider in tree control as i have to access the data later from the database. I'm able to use XMLList as the data provider in the tree control but unable to use ArrayCollection as data

  • How to create mesures for NEW KPI

    In the SET KPI s I don't see an option to create measure, where do we create the measures

  • OEM Security Issue

    Hi All, We'd like to use OEM, but our environment is a bit strange. Our systems crew require that users login as their user, then su - oracle in order to 'become' the oracle user. My understanding is that OEM requires a priviledged oracle user to be