T61P LCD Refresh Rate keeps resetting to 60 Hz - Also Brightness maxes out

I tried saving a power profile for the resolution, etc., but maybe I didn't know how to save it properly, so whenever just about anything significant happens to my T61P (logout, restart, change something about the video) it ends up reverting to 60 Hz and since I'm using a Philips 19" CRT second display, the 60 Hz refresh rate just doesn't cut it for my eyes.
Speaking of my eyes, the notebook display also reverts to max. brightness frequently, which is annoying.
Does someone know how I can get the rate to lock on 85 Hz and permanently retain the settings I put in for the power profile? I Just reinstalled the Thinkpad Power Manager but honestly I still need to reboot and see if it's better before I make too much of it here. Thanks!

ConnorBehan wrote:
3) If you do not specify a restricted list of modelines, I'm pretty sure all of them will be read from the EDID. I have only one modeline appearing in the output of xrandr and only one appearing in the XFCE display dialog. I do this in the "Display" SubSections where you list all the bit depths.
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 16
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
EndSection
I never restricted anything, the modes are simply not there in the EDID. Call it manufacturers safety, I call it manucafturers dumbness. Anyway, what I like is full list of modes from 640x480 to maximum supported with every single refresh rate mode which wont kill my eyes (85+ Hz). Usually the highest modes aren't there even if the display supports them. Missing refresh rate modes are the most typical flaw here.
vacant wrote:You could add something similar somewhere when you start X
vacant: Yes, this is one solution, although not nice, but in this case I get
xrandr: Configure crtc 0 failed
when trying manually added mode, as I already wrote.

Similar Messages

LCD refresh rate

I just got my first Mac, so far I'm loving it. I have a 20.1" Viewsonic vx2025 with a horizontal sync range of 30-82 KHz and a vertical refresh range of 50-75 Hz. The Mini correctly set the right native resolution of 1680x1050, but the refresh rate is set to 60, with no other rates available.
I've had a similar struggle with LCDs on Linux (won't go over 60 Hz) and was told that Linux won't do over 60 Hz because that's what LCDs should refresh at. So I wanted to check if Tiger is the same.

If I'm using the term Refresh Rate incorrectly it's because Apple, GNOME/KDE, and Microsoft are all using it incorrectly. If a dialog window to configure my display settings calls a field "Refresh Rate" (and all 4 of them do call it just that) than that's what I call it too.
Core Duo Mini, 2 GB Mac OS X (10.4.5)

T410 Refresh Rate on Battery

Hi,
After I reinstalled my graphics driver, I have been noticing that my refresh rate keeps getting scaled down to 50Hz when I unplug my computer even though I have "Never" set in Power Manager. I am running the latest Intel GMA HD driver from Lenovo's website, and the latest version of Power Manager (3.20) on Windows 7 Home Premium x64. Is there anything I can do in order to get it to stop changing the refresh rate?

IIRC, the issue should've been fixed by now. Try updating to the latest drivers using System Update.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

T61p Wuxga display refresh rates

Hi!
I suspect that my GNU/Linux installation sets the wrong refresh rates for my 15.4" WUXGA 1920x1200 display. It sets the vertical rate at 50, which seems very low.
I can't seem to find what the correct rates are in the documentation that came with the computer. Does anyone know? If you don't know the horizontal rate, I'm still interested in the vertical rate. What does Vista set? (I removed Vista, so I can't check myself.)
Please help!

Adamaxus -- searching the web I find a lot of such claims. I didn't know this. But I do know from my own experience that vertrefresh has a huge impact on my stationary lcd monitor. Are there different kinds of lcds that behave differently in respect to vertrefresh?
Anyway, I don't have any flicker on my T61p screen. It only bothers me that xorg and nvidia-settings report different refresh rates, and that some GL applications might get the wrong info and slow down because of it.This is one of the explanations floating around the net for slow gl desktops on T61p.
If 50 is the default refresh rate, I would think that xorg is right and nvidia-settings is wrong (it reports 60).

Macs Won't Forget Refresh Rate - LCD Refresh Out of Range

I have a new Viewsonic LCD for an old G4. I had to use an ADC to DVI adapter.
The first time I booted up my Mac, the monitor worked fine. I went into the Display Preferences and, like an idiot, I selected 90 hz because, like an idiot, I thought 90 hz was better than 60 hz.
My screen went black and the monitor said "Frequency out of range", etc. I have talked to AppleCare and I have tried everything and nothing I do gets this Mac to revert to 60 hz at 1280 x 1024.
Tried zapping PRAM, didn't work.
Tried booting into Safe Mode and selecting another resolution. I do that, reboot, it reboots in that lower resolution. I select 1280 x 1024 and my screen goes black because it's going into that 90 hz.
Created another account, didn't work.
I plugged in my old CRT into the VGA port. I was able to select 1280 x 1024 at 60 hz. Turned off the Mac. Plugged in the LCD. Turned the Mac back on and it went black.
It does this when you log in. The actual bootup is in 1280 x 1024 60 hz. I get the login screen fine. It's when I log in, into any account, it goes back to that 90 hz mode.
In Windows, if you select a resolution or refresh rate, a dialog comes up asking you if this mode is OK and if after 15 seconds you don't click on anything, it reverts back to the original resolution. Apple doesn't want to do that, I guess, because they want me to use their monitors.
Any ideas?
Thanks!

You should probably just trash the preferences file(s). That will give you a fresh start with the Viewsonic. See this thread:
http://discussions.apple.com/thread.jspa?messageID=3308488&#3308488

How Can I change my refresh rate to 75hz for on LCD using 91.47 drivers?

HI,
I use a 19" LCD and have always changed my refresh rate to 75hz to avoid ghosting in games like fifa 06 (60hz causes a nasty ghost on my 8ms panel). I have been using the 81.98 drivers and could create an override to use 75. The new driver will allow me to change the refresh rate to 75, but will not let me use it - I get the message "The custom resolution cannot be added". I have coolbits2 installed. Is there a registry setting that I can add to allow me to change the refresh rate? If not, I'll just go back to the 81.98. I am also using the DVI connection.
Thank you,
* This is on my Sli PC in my sig. *

I know that on my particular LCD monitor, if I go above the recommended rates, then the screen will just go black and won't let me see anything. Usually it displays a message telling me that it cannot display. I think it especially does this with the DVI connection.
You may have tried it allready, but just make sure that in your display properties you have unchecked the option to only display resolutions allowed by the monitor.
You may also want to try and see if it will let you do it with a VGA connection instead of the DVI.
Otherwise, you just may have to go back to the earlier driver.

Quicktime Video on an LCD Projector Problems & Refresh Rate?

I'm having an issue and don't have a lot of experience with this but hopefully someone has some insight.
When i play back video (formats including DV, DV50, HDV, PRORES422 / interlaced or progressive / frame rates of 23.98 or 29.97) in full screen using Quicktime Player (version 7.4.5) and Present (Shift CMD F) to a projector, the video plays and looks good, with the exception of during certain portions of the video (generally, with a lot of motion), i see either a flicker or what appears to be a scan line, tear, or a trace that scrolls vertically up the image. The flickering/trace is consistent with regard to a particular portion of the video, though when i adjust the refresh rate for the projector, the behavior of the flicker or scrolling trace changes (say at 60hz, it scrolls slowly up vs 85hz where i see mostly flickering/tearing of the image or multiple traces scrolling up). I've tried 3 different projectors, and every combination of screen resolution and refresh rate with no success.
I should point out that when i play these videos full screen on a cinema display (20in or 23in) i don't see this behavior at all.
So, i have a few specific questions:
1. Is anyone familiar with this behavior and any solutions?
2. The projector is connected with a VGA cable and DVI adapter. Might a DVI cable resolve the issue? Is the behavior a result of the analog input? (The cinema displays are connected via DVI and don't exhibit the behavior)
3. If it is a projector issue, any recommendations on a good projector for presenting video played back from a computer?
Thanks in advance for your help. If i've posted in the incorrect forum, please do direct me to the right place.
Shane

Just a fast reply... something to think about...
Use 60hz, most lcd are 60hz. Check you resolution specs for the projector. If the native resolution is 800x600 use that setting if higher use that.....
If your using the lcd as a secondary display try setting the main display to the same specs. Sometime a mismatch between the two displays can cause problems.
Go with the lcd spec settings that's the main priority and the main display isn't.

Increase refresh rate of my LCD display

Hey hey hey. How can I increase the refresh rate available for my LCD display? Should I increase the refresh rate? I cannnot find where to change it.

There are different refresh rates that you can set, but I agree, 60 should be adquate. You can check this under Control Panel, Display, Settings, Then Click on Advanced, then Monitor. There you will see the refresh rate. Unclick the "Hide modes..." and you will see other rates which may not be able to be applied to your machine.

Altering refresh rates

Howdy folks!
I've got an 800mhz emac. The CRT is shot. I am able to use the external monitor plug. I had (have) an external Mac monitor but it is as big as the emac and I am running out of desk space. I bought a 15" Gateway LCD off a craigslister to park in front of the emac chassis. I got the message the the input was out of range for the monitor. I reconnected the mac monitor and tried to reset the refresh rate. There were other rates listed but they were greyed out and not accesible. After lots of reading on this board I found a link to an application called SwitchResX which allowed me to make the changes I need and the LCD is working now.
Here's the rub: SwitchResX is a 10 day limited shareware product. It costs $18.50 (or thereabouts) to register it. I will pay it in the end if I can't find relief elsewhere but I feel like I ought to be able to accomplish a change in video refresh rates without having to shell out $$ to a third party.
Anyone know of a more straightforwad, less costly way to achieve DIY video adjustments?
TIA!

Bump for last minute plea before paying ....

Changing refresh rate blanks screen indefinitely

Hi all,
I'm new to the mac world and I was exploring OSX upon bringing my new Mac Pro home.
I have an old 17" Benq LCD monitor (upgrading soon) that I had hooked up using the analog to DVI adapter. I've heard that LCD's usually always are set at 60Hz but stupid me had to try other refresh rates. I set the refresh rate to 80Hz and the screen went blank and a box came up stating the refresh rate was "out of range".
I thought that it would automatically revert a la XP but after 5 minutes nothing. So in the meantime I just swapped to a different video output on the video card.
Could someone please tell me how I can revert the refresh rate to 60Hz so that DVI output can be utilized.
Thanks for reading!
Cheerz,
Flu
Mac Pro Quad Mac OS X (10.4.10)

Use the "Gather Windows" button in the "Display" pane of "Displays" System Preference. You can change setting for both displays from one display. You can also check "Show displays in menu bar" to get control of both displays.
Resetting PRAM, or a Safe Boot might help.
<http://docs.info.apple.com/article.html?artnum=107393>

Sony KDL32W4000 - missing bits on overscan; blurry; refresh rate

I've connected the mini to the TV (which is a full 1920x1080 HD set) - using mini-DVI to DVI-D to HDMI.
When in overscan I'm missing the edges of the screen - the menu bar at the top is outside the physical border of the screen but is usable (ie I can use the mouse in the border of the screen but can't see either the mouse or the top line of the menu). When it's not in overscan I'm using about three quarters of the screen.
Is there a way to make it fit the screen within the physical borders of the set (ie using overscan but keeping the borders of the screen within the physical boundaries of the set - or turning overscan off but expanding the screen out to the boundaries of the set).
It is, I think, a 100hz set but in display options I'm only seeing 60hz - is there a way to increase the refresh rate when used by the mini?
The screen fonts are also a bit blurry - any tips on who to improve visual acuity?
I haven't upgraded to 10.5.7 at this stage due to the problems people have been having with it - will do so once I do a time machine backup of the current setup.
Thanks.

Answering my own questions again - you get the full screen filled out to (but not past) the borders of the set if you set the display area to full pixel rather than "normal" (press Home on the remote then navigate using XMB to settings) and then on the Mini set the Mini's display prefs to overscan. The full pixel setting only affects the TV when it is getting a signal from the pc and doesn't apply when it is used as a TV (so no need to reset it when you want to use the TV as a telly). The font still isn't amazing but this may be due to me sitting further back than I'm used to.

Problems getting a higher framebuffer refresh rate

Hello everyone just changed from Gentoo to Arch
Anyway here is my problem, I usually use a framebuffer resolution of 1280x1024-32@75. I used to use a Nvidia BFG Geforce Ti4200SE 128MB and it had no problem of booting into the above resolution. I recently upgraded to a Nvidia Chaintech Geforce 6600 GT 128MB AGP and since then the refresh rate stays at 60 regardless of the resolution (tried 1024x768). In Xorg the refresh rate does change to 75.
Solutions I have tried are:
Patching my kernel with the vesafb-tng patch and setting my resolution and refresh rate in the kernel, but that didn't work.
Using fbset, found this on gentoo forums.:
xvidtune -show | ./modeline2fb.pl >> /etc/fb.modes
modeline2fb.pl
#!/usr/bin/perl
# Written by Michal Januszewski <[email protected]>
# Based on octave script from http://www.linuxdocs.org/HOWTOs/Framebuffer-HOWTO-14.html.
# Usage:
# xvidtune -show | ./modeline2fb.pl >> /etc/fb.modes
$modeline = <STDIN>;
$modeline =~ /".*"s+([d.]+)s+(d+)s+(d+)s+(d+)s+(d+)s+(d+)s+(d+)s+(d+)s+(d+)/;
$dcf = $1;
$hr = $2;
$sh1 = $3;
$sh2 = $4;
$hfl = $5;
$vr = $6;
$sv1 = $7;
$sv2 = $8;
$vfl = $9;
$pixclock = 1000000 / $dcf;
$left_margin = $hfl - $sh2;
$right_margin = $sh1 - $hr;
$hsync_len = $sh2 - $sh1;
# 3) vertical timings:
$upper_margin = $vfl - $sv2;
$lower_margin = $sv1 - $vr;
$vsync_len = $sv2 - $sv1;
$rr = $dcf / ($hfl * $vfl) *1e6;
$hsf = $dcf / $hfl * 1e3;
printf("mode "%dx%d"n",$hr,$vr);
printf(" # D: %3.2f MHz, H: %3.2f kHz, V: %2.2f Hzn", $dcf, $hsf, $rr);
printf(" geometry %d %d %d %d %dn", $hr, $vr, $hr, $vr, 32);
printf(" timings %d %d %d %d %d %d %dn",
$pixclock, $left_margin, $right_margin,
$upper_margin, $lower_margin,
$hsync_len, $vsync_len);
printf("endmoden");
fb.modes
mode "1280x1024"
# D: 135.00 MHz, H: 79.98 kHz, V: 75.02 Hz
geometry 1280 1024 1280 1024 32
timings 7407 248 16 38 1 144 3
endmode
However fbset 1280x1024 keeps the framebuffer refresh rate at 60.
Is there anything else I can try?
Kernel= 2.6.12 patched with vesafb-tng, inotify, fbsplash
System=
Athlon-xp 2600
768MB pc3200
Chaintech 6600 GT AGP
450W Rosewill PSU
Boot=
root (hd0,1)
kernel (hd0,1)/kernel-2.6.12-arch-r3 quiet devfs=nomount root=/dev/hda4 video=vesafb:ywrap,mtrr,1280x1024-32@75 splash=silent,fadein,kdgraphics,theme:darch CONSOLE=/dev/tty1

Some thoughts...
how much is calibration? how much is that TV?
some say TV's should be calibrated again after 6 months of usage where the TV has had some break-in. How much is that second calibration???
some say they just run on theatre or cinema mode to save costs
some say they don't like the calibration and flip back to the normal, bright or vivid mode. Personally I hate to see the highlights punched out and looseing detail for the brightness
some purchase Spyder or XRite calibration tools
some will use Apps to do their own calibration (note you need a cable or a wireless box), however you don't want someone who is colorblind making those calibration decisions (like me)
https://itunes.apple.com/ca/app/thx-tune-up/id592624594?mt=8
http://www.pcmag.com/article2/0,2817,2414804,00.asp
http://www.youtube.com/watch?v=rOoizmYBHlo&hd=1
When shopping for a TV I visited several retailers. For the stores who calibrated their displays.... I had a tough time deciding which one to get because they were ALL good. I could not tell which one was LCD, LED, or Plasma. Yes calibration is worth it, but how much do you want to spend?

Judder using Mplayer... maybe force different resolution/refresh rate?

Hi!
(I posted this in the newbie section too, but this is maybe the most appropriate place??)
I've set up my computer as a media center using Freevo. As the main media player in Freevo I use Mplayer. The setup is working beautifully, but I'm getting some judder and it's a bit annoying. It's most noticable during bright, fast moving scenes.
So I've been trying to figure out how to remedy this, but it's harder than I thought. My setup is the following:
AMD 4200+ dual core, 2 gigs ram, Nvidia 7800GTX, 24" LCD and Pioneer LX508D plasma TV, and I'm using CoreAVC as decoder (amazing piece of software )
When I bought the 24" screen for my computer the sales guy (using windows) forced the resolution to 1920x1080. It looked a bit stretched, but if I could do this in Linux I'd avoid having parts of the picture missing on my TV. Now I have to use 1920x1200 resolution as main X session and since my TV is 1920x1080 parts of the desktop is out of view on my TV. This isn't too big of a deal though cause when playing movies they come out in 1920x1080. It'd be nice though to get the correct aspect ratio between my pc screen and my TV (I've been trying to use Twinview and clone, but it's impossible to use 1920x1200 on the 24" and 1920x1080 on the TV at the same time). I've tried to force my pc screen to use 1920x1080 (since it worked in windows it's supposed to be possible), but when I enable it through xorg.conf the screen goes blank. Using nvidia-settings doesn't give me the option of using 1920x1080 on the 24" at all.
So what I'm hoping to be able to do is to force the computer screen to use 1920x1080 and a refresh rate of 72Hz. This should eliminate alot of the judder and at the same time I won't have to use the "PC mode" on my TV (PC mode restrict the Hz to max 60Hz). Hopefully the TV will accept the 1920x1080 72Hz as any input and let me use the normal input (and then be able to use 72Hz... or 96Hz for that matter).
Anyone know how I might be able to do that? I'd really appreciate any help at all since this is the only thing that's not perfect with my setup.

Ok, I tried to change the xorg.conf file to 72Hz on the TV and it when black again. This is what the xorg.0.log shows:
X.Org X Server 1.4.2
Release Date: 11 June 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.25-ARCH i686
Current Operating System: Linux arch 2.6.25-ARCH #1 SMP PREEMPT Mon Jul 14 15:25:51 UTC 2008 i686
Build Date: 21 June 2008 05:47:59PM
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Jul 19 13:36:04 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Videocard0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) Option "Xinerama" "0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/Type1" does not exist.
Entry deleted from font path.
(==) Including the default font path /usr/share/fonts/misc,/usr/share/fonts/100dpi:unscaled,/usr/share/fonts/75dpi:unscaled,/usr/share/fonts/TTF,/usr/share/fonts/Type1.
(**) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/misc,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/TTF,
/usr/share/fonts/Type1
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81e0a60
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 2.0
X.Org XInput driver : 2.0
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 2.0
(--) using VT number 3
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1002,5950 card 103c,2a24 rev 10 class 06,00,00 hdr 00
(II) PCI: 00:02:0: chip 1002,5a34 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:12:0: chip 1002,4379 card 103c,2a24 rev 00 class 01,01,8f hdr 00
(II) PCI: 00:13:0: chip 1002,4374 card 103c,2a24 rev 00 class 0c,03,10 hdr 80
(II) PCI: 00:13:1: chip 1002,4375 card 103c,2a24 rev 00 class 0c,03,10 hdr 00
(II) PCI: 00:13:2: chip 1002,4373 card 103c,2a24 rev 00 class 0c,03,20 hdr 00
(II) PCI: 00:14:0: chip 1002,4372 card 103c,2a24 rev 11 class 0c,05,00 hdr 80
(II) PCI: 00:14:1: chip 1002,4376 card 103c,2a24 rev 00 class 01,01,8a hdr 00
(II) PCI: 00:14:3: chip 1002,4377 card 103c,2a24 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:14:4: chip 1002,4371 card 0000,0000 rev 00 class 06,04,01 hdr 81
(II) PCI: 00:18:0: chip 1022,1100 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 00:18:1: chip 1022,1101 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 00:18:2: chip 1022,1102 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 00:18:3: chip 1022,1103 card 0000,0000 rev 00 class 06,00,00 hdr 80
(II) PCI: 01:00:0: chip 10de,0091 card 10de,02c2 rev a1 class 03,00,00 hdr 00
(II) PCI: 02:01:0: chip 13f6,0111 card 153b,1144 rev 10 class 04,01,00 hdr 00
(II) PCI: 02:03:0: chip 10ec,8139 card 103c,2a24 rev 10 class 02,00,00 hdr 00
(II) PCI: 02:04:0: chip 1106,3044 card 103c,2a24 rev 80 class 0c,00,10 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,2), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:2:0), (0,1,1), BCTRL: 0x000a (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000e000 - 0x0000efff (0x1000) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xfa000000 - 0xfcffffff (0x3000000) MX[b]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:20:3), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) Subtractive PCI-to-PCI bridge:
(II) Bus 2: bridge is at (0:20:4), (0,2,2), BCTRL: 0x0002 (VGA_EN is cleared)
(II) Bus 2 I/O range:
[0] -1 0 0x0000d000 - 0x0000dfff (0x1000) IX[b]
(II) Bus 2 non-prefetchable memory range:
[0] -1 0 0xfde00000 - 0xfdefffff (0x100000) MX[b]
(II) Bus 2 prefetchable memory range:
[0] -1 0 0xfdd00000 - 0xfddfffff (0x100000) MX[b]
(--) PCI:*(1:0:0) nVidia Corporation G70 [GeForce 7800 GTX] rev 161, Mem @ 0xfa000000/24, 0xd0000000/28, 0xfb000000/24, I/O @ 0xef00/7
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI I/O resource overlap reduced 0x00004100 from 0x0000411f to 0x000040ff
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xe0000000 to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[1] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[2] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[3] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[4] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[5] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[6] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[7] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[8] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[9] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[10] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[11] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[12] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[13] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[14] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[15] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[16] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[17] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[18] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[19] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[20] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[21] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[23] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[24] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[25] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
(II) Inactive PCI resource ranges:
[0] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[1] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[2] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[3] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[4] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[5] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[6] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[7] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[8] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[9] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[10] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[11] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[12] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[13] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[14] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[15] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[16] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[17] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[18] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[19] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[20] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[21] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[23] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[24] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[25] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
(II) Inactive PCI resource ranges after removing overlaps:
[0] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[5] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[6] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[7] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[8] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[9] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[10] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[11] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[12] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[13] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[14] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[16] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[17] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[18] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[19] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[20] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[21] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[22] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[23] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[24] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[25] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[26] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[27] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[28] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[29] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[30] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[31] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
[32] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "freetype" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded by default.
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Server Extension
(II) NVIDIA GLX Module 173.14.09 Thu Jun 5 00:07:40 PDT 2008
(II) Loading extension GLX
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "xtrap"
(II) Loading /usr/lib/xorg/modules/extensions//libxtrap.so
(II) Module xtrap: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DEC-XTRAP
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.4.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "nvidia"
(II) Loading /usr/lib/xorg/modules/drivers//nvidia_drv.so
(II) Module nvidia: vendor="NVIDIA Corporation"
compiled for 4.0.2, module version = 1.0.0
Module class: X.Org Video Driver
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.3.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) LoadModule: "kbd"
(II) Loading /usr/lib/xorg/modules/input//kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.3.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.0
(II) NVIDIA dlloader X Driver 173.14.09 Wed Jun 4 23:47:25 PDT 2008
(II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset NVIDIA GPU found
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "wfb"
(II) LoadModule: "wfb"
(II) Loading /usr/lib/xorg/modules//libwfb.so
(II) Module wfb: vendor="X.Org Foundation"
compiled for 1.4.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"(II) Module "ramdac" already built-in
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[5] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[6] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[7] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[8] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[9] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[10] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[11] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[12] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[13] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[14] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[16] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[17] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[18] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[19] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[20] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[21] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[22] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[23] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[24] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[25] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[26] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[27] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[28] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[29] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[30] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[31] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
[32] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[5] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[6] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[7] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[8] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[9] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[10] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[11] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[12] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[13] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[14] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[20] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[21] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[22] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[23] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[24] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[25] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[26] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[27] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[28] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[29] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[30] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[31] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[32] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[33] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[34] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
[35] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
(==) NVIDIA(0): RGB weight 888
(==) NVIDIA(0): Default visual is TrueColor
(==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
(**) NVIDIA(0): Option "NoLogo" "true"
(**) NVIDIA(0): Option "TwinView" "1"
(**) NVIDIA(0): Option "TwinViewOrientation" "Clone"
(**) NVIDIA(0): Option "MetaModes" "DFP-0: 1920x1200 +0+0, DFP-1: 1920x1080_72 +0+0"
(**) NVIDIA(0): Option "TwinViewXineramaInfoOrder" "DFP-0"
(**) NVIDIA(0): Enabling RENDER acceleration
(**) NVIDIA(0): TwinView enabled
(II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is
(II) NVIDIA(0): enabled.
(II) NVIDIA(0): NVIDIA GPU GeForce 7800 GTX (G70) at PCI:1:0:0 (GPU-0)
(--) NVIDIA(0): Memory: 262144 kBytes
(--) NVIDIA(0): VideoBIOS: 05.70.02.11.20
(II) NVIDIA(0): Detected PCI Express Link width: 16X
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(--) NVIDIA(0): Connected display device(s) on GeForce 7800 GTX at PCI:1:0:0:
(--) NVIDIA(0): BenQ G2400W (DFP-0)
(--) NVIDIA(0): PIONEER_PDP. (DFP-1)
(--) NVIDIA(0): BenQ G2400W (DFP-0): 310.0 MHz maximum pixel clock
(--) NVIDIA(0): BenQ G2400W (DFP-0): Internal Dual Link TMDS
(--) NVIDIA(0): PIONEER_PDP. (DFP-1): 155.0 MHz maximum pixel clock
(--) NVIDIA(0): PIONEER_PDP. (DFP-1): Internal Single Link TMDS
(II) NVIDIA(0): Display Devices found referenced in MetaMode: DFP-0, DFP-1
(II) NVIDIA(0): Assigned Display Devices: DFP-0, DFP-1
(II) NVIDIA(0): Validated modes:
(II) NVIDIA(0): "DFP-0:1920x1200+0+0,DFP-1:1920x1080_72+0+0"
(II) NVIDIA(0): Virtual screen size determined to be 1920 x 1200
(--) NVIDIA(0): DPI set to (93, 95); computed from "UseEdidDpi" X config
(--) NVIDIA(0): option
(==) NVIDIA(0): Enabling 32-bit ARGB GLX visuals.
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfdefe000 - 0xfdefe7ff (0x800) MX[b]
[5] -1 0 0xfdeff000 - 0xfdeff0ff (0x100) MX[b]
[6] -1 0 0xfe02b000 - 0xfe02b3ff (0x400) MX[b]
[7] -1 0 0xfe02c000 - 0xfe02cfff (0x1000) MX[b]
[8] -1 0 0xfe02d000 - 0xfe02dfff (0x1000) MX[b]
[9] -1 0 0xfe02e000 - 0xfe02efff (0x1000) MX[b]
[10] -1 0 0xfe02f000 - 0xfe02f1ff (0x200) MX[b]
[11] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[12] -1 0 0xfb000000 - 0xfbffffff (0x1000000) MX[b](B)
[13] -1 0 0xd0000000 - 0xdfffffff (0x10000000) MX[b](B)
[14] -1 0 0xfa000000 - 0xfaffffff (0x1000000) MX[b](B)
[15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[19] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[20] -1 0 0x0000dd00 - 0x0000dd7f (0x80) IX[b]
[21] -1 0 0x0000de00 - 0x0000deff (0x100) IX[b]
[22] -1 0 0x0000df00 - 0x0000dfff (0x100) IX[b]
[23] -1 0 0x0000f800 - 0x0000f80f (0x10) IX[b]
[24] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[25] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[26] -1 0 0x000001f0 - 0x000001f0 (0x1) IX[b]
[27] -1 0 0x000001f0 - 0x000001f7 (0x8) IX[b]
[28] -1 0 0x00000500 - 0x0000050f (0x10) IX[b]
[29] -1 0 0x0000fa00 - 0x0000fa0f (0x10) IX[b]
[30] -1 0 0x0000fb00 - 0x0000fb03 (0x4) IX[b]
[31] -1 0 0x0000fc00 - 0x0000fc07 (0x8) IX[b]
[32] -1 0 0x0000fd00 - 0x0000fd03 (0x4) IX[b]
[33] -1 0 0x0000fe00 - 0x0000fe07 (0x8) IX[b]
[34] -1 0 0x0000ef00 - 0x0000ef7f (0x80) IX[b](B)
[35] -1 0 0x00004100 - 0x000040ff (0x0) IX[b]O
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) NVIDIA(0): Initialized GPU GART.
(II) NVIDIA(0): Unable to connect to the ACPI daemon; the ACPI daemon may not
(II) NVIDIA(0): be running or the "AcpidSocketPath" X configuration option
(II) NVIDIA(0): may not be set correctly. When the ACPI daemon is
(II) NVIDIA(0): available, the NVIDIA X driver can use it to receive ACPI
(II) NVIDIA(0): events. For details, please see the "ConnectToAcpid" and
(II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
(II) NVIDIA(0): Config Options in the README.
(II) NVIDIA(0): Setting mode "DFP-0:1920x1200+0+0,DFP-1:1920x1080_72+0+0"
(II) Loading extension NV-GLX
(II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
(II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
(==) NVIDIA(0): Backing store disabled
(==) NVIDIA(0): Silken mouse enabled
(II) Loading extension NV-CONTROL
(==) RandR enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Initializing extension GLX
(**) Option "Protocol" "auto"
(**) Mouse0: Device: "/dev/input/mice"
(**) Mouse0: Protocol: "auto"
(**) Option "CorePointer"
(**) Mouse0: always reports core events
(**) Option "Device" "/dev/input/mice"
(**) Option "Emulate3Buttons" "yes"
(**) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5 6 7"
(**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
(**) Mouse0: Buttons: 11
(**) Mouse0: Sensitivity: 1
(**) Option "CoreKeyboard"
(**) Keyboard0: always reports core events
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "trustda"
(**) Keyboard0: XkbModel: "trustda"
(**) Option "XkbLayout" "no"
(**) Keyboard0: XkbLayout: "no"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(II) evaluating device (Keyboard0)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) evaluating device (Mouse0)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
(II) Mouse0: ps2EnableDataReporting: succeeded
Could not init font path element /usr/share/fonts/Type1, removing from list!
My xorg.conf looks like this now (I don't know what values to use for HorizSync and VertFresh on my TV, the ones that are in there I just made up ):
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder63) Mon May 19 00:34:28 PDT 2008
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "glx"
Load "dbe"
Load "xtrap"
Load "extmod"
Load "record"
Load "freetype"
EndSection
Section "ServerFlags"
Option "Xinerama" "0"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
Option "XkbRules" "xorg"
Option "XkbModel" "trustda"
Option "XkbLayout" "no"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "BenQ G2400W"
HorizSync 31.0 - 94.0
VertRefresh 50.0 - 85.0
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Unknown"
ModelName "PIONEER_PDP."
# HorizSync 15.0 - 80.0
# VertRefresh 23.0 - 60.0
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "G70 [GeForce 7800 GTX]"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "Videocard0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 7800 GTX"
EndSection
Section "Device"
Identifier "Videocard1"
Driver "nvidia"
VendorName "NVIDIA Corporation"
BoardName "GeForce 7800 GTX"
BusID "PCI:1:0:0"
Screen 1
EndSection
Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
Option "NoLogo" "true"
Option "TwinViewOrientation" "Clone"
Option "TwinView" "1"
Option "TwinViewXineramaInfoOrder" "DFP-0"
Option "metamodes" "DFP-0: 1920x1200 +0+0, DFP-1: 1920x1080_72 +0+0"
SubSection "Display"
Depth 24
EndSubSection
EndSection
I read somewhere that the TV is supposed to be able to show 1080p in 72Hz. But when I try that it goes blank. Maybe it has something to do with the monitor being 1920x1200 and the TV 1920x1080. The monitor won't accept 1920x1080 as resolution so I guess that can only be done in Windows...

Can't change Refresh Rate

To try to get my new Samsung LN-R268W monitor to show what's on the screen of my Power Book G4 (OS 10.4.5), the lady at Samsung Customer Support said I need to make sure my Refresh Rate is 60 hertz. System Preferences>Displays>Color LCD>Display had the Refresh Rate showing a greyed-out "n/a." Advice?

Is this before or after you've got the image on your
Samsung? If it's before you've connected it, or used
the F7 key to toggle to mirror/span mode, the only
display you'll see under System Preferences is the
built in display. And the refresh rate for that will
be "n/a".
Most monitors will be auto-detected by OS X, and the
refresh rate will be set without any input. My 20"
widescreen Dell LCD automagically defaults to 60Hz.
At any rate, refresh rates for LCDs are kind of
meaningless - they don't actually refresh like old
CRT monitors do.
Is this before or after you've got the image on your
Samsung? If it's before you've connected it, or used
the F7 key to toggle to mirror/span mode, the only
display you'll see under System Preferences is the
built in display. And the refresh rate for that will
be "n/a".
Most monitors will be auto-detected by OS X, and the
refresh rate will be set without any input. My 20"
widescreen Dell LCD automagically defaults to 60Hz.
At any rate, refresh rates for LCDs are kind of
meaningless - they don't actually refresh like old
CRT monitors do.
You're right. Today I learned from talking to somebody that I should turn on my monitor before I turn on my laptop. Page 53 of the Apple manual "Getting Started With Your Powerbook G4" suggested the opposite. However, if I had read page 53 and its reference to page 97 more carefully, I would have checked the "mirroring" box.

24" iMac refresh rate

I am having all those horrible problem with battlefield 2142 that everyone else is having, but i just found the file that has all the configurations for the game, such as the screen resolutions. My normal resolution is at 1920x1200, but the game resolution is stuck at 1024x800 @ 60hz. i tried to enter the larger resolutions including 1920x1200 but the game just crashes. SO thinking about it i think i have the wrong refresh rate. i went through system preferences and at the refresh rate says "n/a" as seen here....
!http://farm2.static.flickr.com/1165/1427575277e25330d756o.jpg!
i also checked system profiler... nothing....
!http://farm2.static.flickr.com/1237/1428482292a9cb9b3555o.jpg!
that being said does anyone know the refresh rates for the reolutions of the 24" iMac?
the help would be greatly appreciated by many including myself x100....

Roger Wilmut1 wrote:
I suspect that 'refresh rate' is only applicable to CRT monitors: my flat-panel iMac has it greyed out as well.
Not sure if the lack of refresh rate selection is normal for an iMac, but I can defnitely select the refresh for my 17" LCD monitor.
It seems more likely that the game simply won't work at higher than 1024x800 - particularly as 1920x1200 is a widescreen format and the game very likely wants a 4x3 format. Try setting your monitor to 1024x768
Some games will refuse to run at resolutions lower than 1024x768 or 800x600, but I've never heard of a game that would refuse to be set at a higher resolution…

T61P LCD Refresh Rate keeps resetting to 60 Hz - Also Brightness maxes out

Similar Messages

Maybe you are looking for