T61p restart when try to install the system.
Hello,
I have replaced motherboard on my lenovo T61p, old one was broken ( nivida chipset was burned). But right now after replacing motherboard I'm able to turn it on, i can go to bios setting, run mem test from cd. But when I'm trying to install system (Linux,win 7, win xp) it 's restarting. On windows 7 i can see the first progress bar under the DOS but when the bar is loaded and nice blue windows should appear it restarting. On win xp I'm able to format the hard drive, copy the files to HDD but when it restart and run from HDD, I can see the progress bar " installing device" 39 min left, and restart.
I have replaced Processor,memory, disconnected WIFI ,modem all unnecessary device but i still have this problem.
Maybe someone has this problem before ?
This is a longshot, but substitute a different harddrive if possible. If a drive is pulling to many amps, it will force the system down for lack of power. Any direct current motor, like in a harddrive could draw to much amps and cause this.
This is theory, I've not actually seen a bad drive do this, but it's worth a try.
If you don't have a drive to try, get a linux Live CD disc and boot from your optical drive without a harddrive. That should work , and if it seems stable, then you will need to find a known good trive to test.
ThinkPad W-510 i7-820QM(1.73-3.06GHz) Quad Core... ThinkPad T500, T9900, 8gb SSD...FrankNpad T-60p/61p (X9000 2.8ghz) 8gb SSD ips FlexView...ThinkPad T-61p (T9300 2.5ghz) 8gb ram...Thinkpad X-61 Tablet 4gb ram...ThinkPad A-31 (1.9ghz P4 1.5gb ram)
Similar Messages
-
Error message comes up when try to install Lync 2010 in a windows XP machine
Hi everyone, this issue is from one of our customer, Ravi Hegde. The error message is " the procedure entry point EventWrite could not be located in the dynamic link lirary ADVAPI32.dll" when try to install the Lync 2010 client in a windows XP
manchine.
does anyone here meet the same issue before and share the solution? many thanks.Hi Alex,
Please open an elevated command prompt and run the below command;
sfc /scannow
In the event that this doesn't work you might try some of the the below from reading;
1.) jumping back to a realistic restore point that doesn't create a load of work for you in regards to program installation
2.) performing a repair on the OS
3.) Installing all outstanding windows and office updates as these often replace the existing DLL
4.) Repair of Microsoft Office
5.) clean OS install or image deployment
Kind regards
Ben -
I am running OSX 10.6.8 and when I try to install the latest security update there is an unknown error and the update cannot be implemented. I still have to restart my computer each time I try. Is anyone else experiencing this problem?
I tried using the downloaded update. It still didn't work but at least I did not have to restart my computer. The message was a little different too: "The installation failed. The Installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance."Run through this list of fixes, either something is corrupted or you have malware that's blocking the update.
..Step by Step to fix your Mac
Make sure to backup your users files to a external storage drive first (not only TimeMachine as it may fail to restore) and disconnect, because if' it's a drive corruption/failing then the entire thing will either have to be replaced or a wipe and install done.
Most commonly used backup methods
If you do need to do a wipe and install
How to erase and install Snow Leopard 10.6
For Snow Leopard Speed Freaks -
I try to install the trial version of Adobe After Effects but when it goes to the installer, it gives me an error telling me to restart my laptop. Even after I restart my laptop it gives me the error. Help?
We can't know. You have not provided any system information or the exact error. Most commonly this happens when a security tool is blocking the installers or you run with insufficient user privileges, but that's all we can kinda guess here.
Mylenium -
My mac has OSX version 10.8.2 and I'm try to install an aiport express base station which requires 10.5.7 or later. Yet when I try to install the software it says the base station is not compatible with my mac version - how do I resolve?
You already have the software installed that you need if you have 10.8.2.
If AirPort Utility cannot find the Express, that is another matter. More software is not needed. More troublehooting is needed.
Power up the Express for a full minute
Hold in the reset button on the Express for 7-8 seconds and release
Allow a full minute for the Express to restart
Click the AirPort icon at the top of the Mac's screen
Look for a heading of New AirPort Base Station
Just below that, click on AirPort Express
What happens? -
When I try to uninstall iTunes I get a message saying iTunes 64 msi can not be located and I should enter an alternate path. How would I know where it it is? I get the same message when trying to install the update to iTunes 10.6.1.
Download the Windows Installer CleanUp utility from the following page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
To install the utility, doubleclick the msicuu2.exe file you downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time? -
When I try to install the update for iTunes, I keep getting the message "the application attempted to load the C runtime library incorrectly. Contact the vendor. I don't know if it's related, but my Microsoft Outlook is totally f*k up. What's going on?
Hey I finally got an older vesion of itunes to work!!! 10.7 x64 for windows 7
After uninstalling all apple products even quicktime
I had to delete everything from (program files, and program files x64, program data,)
And all downloads from apple, and I went in to search deleted other stuff from apple, and itunes
But definently not my itunes library and Playlist
Down loaded 10.7 x64 for windows 7, but checked (do not start when done)
Then I emptied my recycling bin and restarted my PC
I ran geek tech tool box same as reg cure pro, also PC Tools registry cleaner, and CC Cleaner
Then I emptied my recycling bin and restarted my PC
And wallah... It finally works, and I Love the older version anyways.
Easier to download and transfer music!!!!! -
Why does my cellphone keep saying that "estimating time remaining" when I try to upgrade the system?
Is there anyway to fix this situation?Hi Eric_Sun,
Thanks for visiting Apple Support Communities.
You may want to update your iPhone using iTunes on a computer if your device only shows "estimating time remaining" when you try to update wirelessly:
If you can’t update wirelessly, or if you want to update with iTunes, follow these steps:
If you use your device's Personal Hotspot for your computer's Internet connection, update your device wirelessly or connect your computer to another network.
Install the latest version of iTunes on your computer.
Plug in your device to your computer.
In iTunes, select your device.
In the Summary pane, click Check for Update.
Click Download and Update.
If you see an error message while updating your device, you can learn how to resolve iOS update errors in iTunes.
You can find these steps here:
Update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/ht4623
If you are still not able to update, I recommend the steps in this article next:
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Best Regards,
Jeremy -
Hi
Due to impossibility to upgrade the i tunes version installated on my computer, i decided to remove it because i had needed to sincronize my new iphone 4s. But when i try to install the i tunes newer version the installation hangs on the collecting product information and only after a long wait i receive the following message :
An error occurred during the installation of assembly ‘Microsoft.VC80.CRT.type=”win32”,version=”8.0.50727.6195”,publicKey Token=”1fc8b3b9a1e18e3b”,processorArchitecture=”x86”.Please refer to Help and Support for more information. HRESULT: 0x800736B3
HeeeeeeeeeeeeeeelpWhat version of Windows are you using? This is not a problem with iTunes. It may have to do with an issue of the compatibility of a newer version of iTunes with an older Windows system/older hardware.
What do you want to synchronize? If you were previously using iCloud you should be able to restore most of your oringinal content onto your new phone via was was last synched with the iCloud on your previous phone/device. -
Hi everybody.
Im still hanged by the same problem i reorted in the message listed below ten days ago.
Is there anyone can hep me ?
Due to impossibility to upgrade the i tunes version installated on my computer, i decided to remove it because i had needed to sincronize my new iphone 4s. But when i try to install the i tunes newer version the installation hangs on the collecting product information and only after a long wait i receive the following message :
An error occurred during the installation of assembly ‘Microsoft.VC80.CRT.type=”win32”,version=”8.0.50727.6195”,publicKey Token=”1fc8b3b9a1e18e3b”,processorArchitecture=”x86”.Please refer to Help and Support for more information. HRESULT: 0x800736B3What version of Windows are you using? This is not a problem with iTunes. It may have to do with an issue of the compatibility of a newer version of iTunes with an older Windows system/older hardware.
What do you want to synchronize? If you were previously using iCloud you should be able to restore most of your oringinal content onto your new phone via was was last synched with the iCloud on your previous phone/device. -
I have a HP Deskjet D4200 series printer that I used with my iBook G4 and I recently purchased a new MacBook Pro 13.5" and I would like to use this printer with my new lap top. When I use the disc to try to install the printer driver, I get a message that "I can't open the application HP Installer because the Power PC applications are no longer supported. I am not sure what all that means but is there any way to use this printer with my new computer?
ThanksIt would help to post this in a more proper form. This is for the iTunes family of stores.
-
I am facing the problem on downloading apps from Mac App Store, when I try to install the application from App store, I am getting an error message "Status_Code_Error" while click on "Login"
Same problem here in Brazil.
It seems to be a problem with logging in App Store in the Mac (Yosemite 10.10.2).
When I tried the very same userid and password I was able to login in to use my iCloud account from the same computer and also from my iPhone. -
I am trying to attach an Ipod touch to an older Power Book G4.
Itunes says that the Ipod cannot be used because it needs Itunes version 9.2 (running 8.0.1).
When I try to install the latest Itunes version 10.3.1 Mac says ("Open failed" requires Mac OX S 10.5.Click here and install the software.
(58765) -
I disabled my Macbook Hard Disk and lock the settings, after i try to reboot, the system wouldn't come up. It refuses to read instructions from the hard disk. How can i enable the hard disk when the system wouldn't come up?
How do you disabled it if running the same?
-
Server0 stooped when I try to start the system...
Hi gurus,
I don´t know what´s happen when I try to start the system and the Java side don´t start, it stay in MMC console with yellow semaphore at disp+work.EXE and when I look inside of J2EE Process Table in the same console the server0 is stopped and it show the exit code -11113 !!
I checked two logfiles:
dev_server0 :
Sun Aug 23 21:42:48 2009
14.537: [GC 14.537: DefNew: 103014K->17353K(131328K), 0.0753503 secs 103014K->17353K(1004800K), 0.0754636 secs]
Sun Aug 23 21:42:50 2009
16.592: [GC 16.592: DefNew: 104905K->18569K(131328K), 0.0589135 secs 104905K->18569K(1004800K), 0.0590141 secs]
Sun Aug 23 21:42:53 2009
JHVM_RegisterNatives: registering methods in com.sap.mw.rfc.driver.CpicDriver
19.422: [GC 19.423: DefNew: 106121K->25119K(131328K), 0.0994074 secs 106121K->25119K(1004800K), 0.0995054 secs]
JHVM_RegisterNatives: registering methods in com.sap.i18n.cp.ConverterJNI
Sun Aug 23 21:42:54 2009
JLaunchIExitJava: exit hook is called (rc = -11113)
ERROR => The Java VM terminated with a non-zero exit code.
Please see SAP Note 943602 , section 'J2EE Engine exit codes'
for additional information and trouble shooting.
JLaunchCloseProgram: good bye (exitcode = -11113)
dev_disp:
DpJ2eeStart: j2ee state = STARTED
rdisp/http_min_wait_dia_wp : 1 -> 1
***LOG CPS=> DpLoopInit, ICU ( 3.0 3.0 4.0.1)
***LOG Q0K=> DpMsAttach, mscon ( sapssm)
DpStartStopMsg: send start message (myname is >sapssm_SSM_00 <)
DpStartStopMsg: start msg sent
Sun Aug 23 21:40:24 2009
CCMS: AlInitGlobals : alert/use_sema_lock = TRUE.
CCMS: Initalizing shared memory of size 60000000 for monitoring segment.
Sun Aug 23 21:40:25 2009
CCMS: Checking Downtime Configuration of Monitoring Segment.
CCMS: start to initalize 3.X shared alert area (first segment).
DpJ2eeLogin: j2ee state = CONNECTED
DpMsgAdmin: Set release to 7000, patchlevel 0
MBUF state PREPARED
MBUF component UP
DpMBufHwIdSet: set Hardware-ID
***LOG Q1C=> DpMBufHwIdSet
DpMsgAdmin: Set patchno for this platform to 201
Release check o.K.
Sun Aug 23 21:40:38 2009
MBUF state ACTIVE
DpModState: change server state from STARTING to ACTIVEHi Arun Singh,
I´m not change any UME parameter. I checked that in fact J2EE_Guest was locked, I already unlocked this user! But I think that is not the problem, because I checked in other systems and in all of them this user is blocked, so don´t seem this is the problem!
The following are server VM settings:
-Djco.jarm=1
-XX:MaxPermSize=256M
-XX:PermSize=256M
-Xms1024M
-XX:NewSize=171M
-XX:MaxNewSize=171M
-XX:+DisableExplicitGC
-verbose:gc
-XX:+PrintGCDetails
-XX:+PrintGCTimeStamps
-Djava.awt.headless=true
-Dsun.io.useCanonCaches=false
-XX:SoftRefLRUPolicyMSPerMB=1
-XX:SurvivorRatio=2
-XX:TargetSurvivorRatio=90
-Djava.security.policy=./java.policy
-Djava.security.egd=file:/dev/urandom
-Dorg.omg.CORBA.ORBClass=com.sap.engine.system.ORBProxy
-Dorg.omg.CORBA.ORBSingletonClass=com.sap.engine.system.ORBSingletonProxy
-Djavax.rmi.CORBA.PortableRemoteObjectClass=com.sap.engine.system.PortableRemoteObjectProxy
Answering to your second question in fact the system have the license out of date! But at two weeks ago the license was in the same state (out of date) and the java side on system was fine!!!...
Best regards,
João Dimas
Maybe you are looking for
-
As this problem appears in more than one application, I can only assume it's something in the Mac OS or HP driver that's causing it. Lately, my photos have been printing too dark from iPhoto, so I played around with a lot of combinations of settings,
-
Change system folders name in mavericks
Hi all, there is a way to change the system folder name in Mavericks as described in this article? http://www.macworld.com/article/1046866/renamesystemfolders.html Thank you
-
I have seen that others have ask about a whitepaper in metalink on hoe to get a project developed in JDev 10g to work with 9iAS(9.0.2). But i can not find any answers!!! Can anyone direct me to the link? Or does anyone know the list of Libraries need
-
Why do I get a warning about downloading J2SE Runtime Environment?
I want to take some courses through SkillSoft, it requires downloading a Java Runtime environment. Before I even started to download I got a Firefox message about something being blocked and that the JRE could cause stability or security problems? I
-
CS5.5: timeline rendered, but still "red line"?
Hello, I rendered the timeline with a nested timeline over night (> 10 h rendering time for 30 minutes video) to work with it in a smooth way, the folder "Adobe Premiere Pro Preview Files" contains a renderd file with 16 GB -- but there is still a "