Table for Quality certificates

Hi QM Guys,
Can anybody tell me what is the table name in which quality certificate is stored?
I am searching particularly for certificate number.
S Dey

Quality Certificates QCPR QM quality certificates in procurement 
Quality Certificates I000 Conditions for certificate profile 
Quality Certificates KONDI Conditions: Data part for certificates 
Quality Certificates QCVK Certificate profile header 
Quality Certificates QCVM Certificate profile characteristic level 
Quality Certificates QCVMT Certificate profile characteristic level: texts
Quality Certificates QCVV Certificate Profile: List of Preliminary Products 
Quality Certificates TQ61 Result value origin for certificates 
Quality Certificates TQ61T Origin of result values for certificates: texts 
Quality Certificates TQ62 Output strategy for skip characteristics 
Quality Certificates TQ62T Output strategy for skip characteristics: texts 
Quality Certificates TQ63 Origin of insp. specs for certificates (function modules) 
Quality Certificates TQ63T Origin of inspection specifications for certificates: texts 
Quality Certificates TQ64 Origin of characteristic short text for certificates 
Quality Certificates TQ64T Origin of characteristic short text for certificates: texts 
Quality Certificates TQ65 Certificates: Combinations allowed for origins, specs/values 
Quality Certificates TQ67 Certificate-Relevant Output Types 

Similar Messages

  • What are the required settings for Quality Certificate

    Hi Team
    What are the required settings for Quality Certificate for Raw material from vendor. This is my RR - Result Recording  for inspection lot.
    Please sugget me T-Code to view this.
    Can I see say for 6-9 months RR done insp. lot.
    Thanks

    Settings for Quality Certificate for Raw material from vendor,
    Activate QM Procurement key, enter qm control key with certificate and Enter certificate type in certificate field.
    There are 2 cases,
    u want details of certificate send by vendor
    u want to record results and see inspection lot wise results.
    case1
    depending upon the certificate selected by u, system will give u warning or error msg for certificate confirmation at the time of gr. for confirmation QC51 t_code is used. here status has to be changed to 'filed and inspected' then gr will be allowed.
    all these certificates can be dispalyed in QC55 T_CODE.
    CASE2
    U can record results and see in inspection report tab in QA33
    Edited by: YOGINI B THORAT on Aug 4, 2009

  • RFC Destination for Quality Certificates

    We are setting up QM and one step is to save quality certificates from suppliers. The problem is we get error "OA009 Storage system not known" on trans QC51, it seems because we do not have defined the Content Repositiry on trns OAC0.
    SAP has predefined values for quality certificates:
    ObjectType: BUS2117
    Doc. Type: QMICERTPDF
    Cont. Rep. ID: D3
    Link: TOA01
    My problem is that when I try to create content repository D3 in trans OAC0 it has a requiered field: RFC destination, which I assume is where the data will be stored, anyone knows which one should I choose?
    Edited by: Carlos Salazar on Apr 16, 2010 8:03 PM
    Edited by: Carlos Salazar on Apr 16, 2010 8:04 PM

    Match code shows these options (on DEV 030):
    Destino RFC
    BACK
    CALLTP_WindowsNT
    CONEXION A QAS
    DEV
    DOCUMENTATION_HELP
    EU_SCRP_TEST
    EU_SCRP_WN32
    F1_HELP_SERVER
    F1_HELP_SERVER_32
    F1_HELP_SERVER_40
    GFW_ITS_RFC_DEST
    IGS_RFC_DEST
    LOCAL_EXEC
    LOCAL_PRINT
    MDX PARSER
    MSSQL_CFGCK
    MSSQL_CFGCK_REG
    NONE
    NONE_NU
    QAS_DEV_DEV_00
    R3_WINDOWS_SERVER
    RECORDER
    RECORDER_NU
    SAP_INTERNET_GATEWAY
    SAP_KEN_IOE
    SAP_SCHEDULE_16
    SAP_SCHEDULE_32
    SAP_SSFATAS
    SAP_SSFATGUI
    SAPBC
    SAPFORMS
    SAPFTP
    SAPFTPA
    SAPGUI
    SAPGUI_QUEUE
    SAPHTTPA
    SAPIRCONTROLLER
    SAPIRPCFILETRANSFER
    SAPJ2EE
    SAPNET_RFC
    SAPNET_RTCC
    SAPOSS
    SDCC_OSS
    SERVER_EXEC
    SLD_NUC
    SLD_UC
    TMSADM @ DEV.DOMAIN_SOL
    TMSADM @ PRD.DOMAIN_SOL
    TMSADM @ QAS.DOMAIN_SOL
    TMSADM @ SOL.DOMAIN_SOL
    TMSSUP @ DEV.DOMAIN_SOL
    TMSSUP @ PRD.DOMAIN_SOL
    TMSSUP @ QAS.DOMAIN_SOL
    TMSSUP @ SOL.DOMAIN_SOL
    VFOLDER
    WORKFLOW_LOCAL_030

  • Settings for Quality Certificates generation

    Hello All,
    I am a new entrant in the forum.  I need your help on quality certificates.
    What are the settings necessary for generating Quality certificates in SAP?
    Sravan

    Hi,
    For quality Certificate
    In material master QM view Should have to assgn the QM Control Key which controls the Certification and also assign the certificate Type.
    Create Certificate profile (Tcode QC01),
    Here For which Inspection type you want to create the certificate assign the Origin and type of inspection.
    Assign the layout set (with ABAP er's help Required form to be created and assign the name here)
    By default QM_QCERT_01
    After creation of profile assign this profile to material/materialand customer com bi
    Regrds
    Praveen

  • Is it possible to Delete all Records of Std. SAP tables for Quality Server

    Hi,
    We want to delete some sensetive information from Test(Quality) Server.
    For Std. SAP tables, is it possible to delete all Records?

    Hi, Through an ABAP program it is possible. You can develop the custom program on Development server than transfer it to QS and run the program.
    Regards,
    Aalok
    Edited by: aalokg on May 13, 2010 12:19 PM

  • Error while filling setup table for Quality Mangement D/Sources

    HI Experts,
    Iam trying to fill the QM setup tables.
    Steps iam following are
    1.T-code OLIQBW
    2.Selecting Event QV, QE and gave selection parameters and name for Run.
    3. Execute
    4.Run Time Error CALL_FUNCTION_PARM_UNKNOWN
       Exception  CX_SY_DYN_CALL_PARAM_NOT_FOUND
       Date and Time          27.08.2009 11:21:01                                                                               
    Function parameter "I_ADDITIONAL_DATA" is unknown.

    Hi Mansi,
    Runtime Errors         CALL_FUNCTION_PARM_UNKNOWN                                                 
    Exceptn                CX_SY_DYN_CALL_PARAM_NOT_FOUND                                             
    Date and Time          27.08.2009 11:56:20                                                                               
    ShrtText                                                                               
    Function parameter "I_ADDITIONAL_DATA" is unknown.                                                                               
    What happened?                                                                               
    Error in ABAP application program.                                                                               
    The current ABAP program "SAPLQMER" had to be terminated because one of the                  
         statements could not be executed.                                                                               
    This is probably due to an error in the ABAP program.                                                                               
    Function module "QEEA_COMBINE_TO_ONE_FEATURE" was called                                     
         with the parameter "I_ADDITIONAL_DATA".                                                      
         This parameter is not defined.                                                                               
    Error analysis                                                                               
    An exception occurred. This exception is dealt with in more detail below                     
         . The exception, which is assigned to the class                                              
          'CX_SY_DYN_CALL_PARAM_NOT_FOUND', was neither                                               
         caught nor passed along using a RAISING clause, in the procedure                             
          "QMER_EXTRACTION_RD_RESULTS" "(FUNCTION)"                                                   
    Since the caller of the procedure could not have expected this exception                     
          to occur, the running program was terminated.                                               
         The reason for the exception is:                                                             
         The reason for the exception is:                                                       
         Function module "QEEA_COMBINE_TO_ONE_FEATURE" was called                               
         with the parameter "I_ADDITIONAL_DATA".                                                
         This parameter is not defined.                                                                               
    Missing RAISING Clause in Interface                                                        
         Program                                 SAPLQMER                                       
         Include                                 LQMER$01                                       
         Row                                     5                                              
         Module type                             (FUNCTION)                                     
         Module Name                             QMER_EXTRACTION_RD_RESULTS                                                                               
    Trigger Location of Exception                                                              
         Program                                 SAPLQMER                                       
         Include                                 LQMERU01                                       
         Row                                     488                                            
         Module type                             (FUNCTION)                                     
         Module Name                             QMER_EXTRACTION_RD_RESULTS

  • Table for Quality Plan

    Hi All,
    I want to download the existing Inspection Plans from the SAP. Please guide me with the Table name which will provide the maximum details (header data, operation data and MICs).
    Thanks in advance
    Sam

    Hi
    You will get the details from these tables
    Inspection Plan PLKO Inspection plan Header 
    Inspection Plan MAPL Material Assignement 
    Inspection Plan PLPO Operation Details 
    Inspection Plan PLMK Inspection plan characteristics 
    Inspection Plan PLMW MAPL-Dependent Charac. Specifications (Inspection Plan) 
    Regards
    Gajesh

  • Re: Quality Certificate requirement At MIGO for raw material

    Dear all,
    I have a requirement where I want the system ask for Quality certificate while doing the goods receipt. The system should not allow me to process the transaction-MIGO if certificate is not recieved.
    Please advice
    Regards,
    Vivek Sharma

    Hi Vivek,
    You need to perform following settings.
    Configuration
    Follow the path
    Run trx QCC0->QM in Logistics->QM in Procurement-->Define Control Keys.
    Here create your own control key
    Where you can set the rest data as per your requirement but for to check the check box for "Cert Required" is must be activated to meet the requirement relevant to this thread.
    Save
    Say you have configured your Control Key ZZ01
    Now just below this one small configuration is mandatory is Run trx QCC0->QM in Logistics->QM in Procurement-->Define Keys for Certificate Processing
    Maintain Description
    Execute it and go to "Define Certificate Types"
    Here either for your relevant certification type or  for new type (if you wish to create new), maintain the data as below
    "Certificate Required for Each Purchase Order Item" ==== Active
    "Certif. per GR Item" ==== Active
    "Certif. check required" ==== Active
    "Control W/O Certif." Set any error message, I would suggest to select "Without lot error message, with lot error message"
    "Enhanced cert. processing" ==== Don't Activate
    "No certif. confirmation at GR" ==== Don't Activate
    The rest settings are not important to maintain so leave them blank.
    At Master Level
    In QM view of MM for the material maintain "QM Control Key" that just created "ZZ01"
    and the certificate type that is just created or amended. under the procurement data.
    Maintain Q-Info record for Material - Vendor - Plant combination (QI01)
    Now as per your requirement system will ask for the confirmation for certificate receipt as Yes/No. under the Purchase Order data in MIGO at item level data.
    If you select "NO" to it it will not allow to post the GR.
    I hope this is what you were looking for.
    Regards,
    Shyamal

  • Quality Certificate for Delivery

    Hi,
    Please guide the basic steps required for Creation of Qulaity Certificate at the time of deilvery with there customization details ?

    Hi !
    There are 4 basic steps for quality certificate:
    1. Create form in SE71.
    2. Create certificate profile in QC01
    3. Release certificate profile in QC01
    4. assign certificate( mateial, material group or combination of materia-customer in QC15)
    You can study in details in Link:[http://help.sap.com/printdocu/core/Print46c/en/data/pdf/QMCA/QMCA.pdf]
    Go through the steps in IDES first, in case any clarification needed do write back.
    Edited by: Swarnali_D on May 21, 2010 11:01 AM

  • Quality certificate -  Delivery ,Inspection lot

    Dear guys,
    Hope every one is doing well
    Here is my question, this is the first time i am working on Quality certificates
    From sap help came to know that
    For Quality certificate for Delivery we need to create a certificate profile , forms that is lay out and contents of the certificate
    and we need to assign to material and sales organization or customer
    Thats clear for me, but also we need to define the output type as LQCA and LQCB if it is ship to party or sold to party
    so i belive that when ever delivery Inspection lot UD is done Quality certifiacte is printed according to certificate profile and output type
    i belive that the charactersitics of the inspection lot also printed in the Quality certificate
    system gets the information from certificate profile , in the charecteristic assignement
    just please someone help me that my understanding is correct
    Also i need to know if i want to print Quality certificate for inspection lot how do i set the output type as there is nothing like LQCA,LQCB for inspection lot
    please help me what setting i need to do for printing inspection lot Quality certificate
    Thanks in advance
    Raj

    Dear kaushik,
    You are great, its just nice and happy to see my first inspection lot print out
    thanks a lot
    Just another Quick question regarding vendor Quality certificate, there is a requirement that vendor certificates to be scanned and uploaded in sap optical archive link
    is there any standard transcation in sap , is there any customization need to done in functional point of view , or i need to work with abaper to create a new transcation code to upload
    Throw some lights
    Thanks
    Raj

  • Set up quality certificate printing for deliveries

    Hi,
    to print a quality certificate for a delivery,
    1. do you need a certificate profile? Or is that only for QC for a batch and for an inspection lot?
    2. do you always use usage B?
    3. do you always use application V2?
    4. how do you set up condition tables, access sequences, condition types and output determination procedures?
    I created an output type (copy of LQCA) in application V2, assigned a program (RQCAAP00), a form routine (entry) and a form (QM_QCERT_01). I also created and released a certificate profile.
    But when I run QC20, I get the message
    "No messages for initial processing exist".
    What could be the error?
    Thx.
    Jessica

    Yes, you always need a certificate profile.  Usually you always use V2 (shipping).  The form you used, QM_QCERT_01 is only an example form that SAP provides.  It should be copied and must be adapted for your businss and you'll need a person knowledgable about SAPscript to make changes to it.  I  believe there is another for a COC (Certificate of compliance) which might be more what your looking for if you don't need to report batch values or inspection lot vales.
    Your probaly missing the certificate recipent record.  You'll find this under the QM area under Outgoing certificates.  You can try adding LQCA output type directly to the delivery in the item outputs.  (Any good SD person on site should be able to show you how to do this)
    To understand condition tables and procedures I would again turn to an SD person or a pricing person.  They use the condition technique a lot and should be able to explain it easilly.  They should also be able to help with setting up the output procedures and related items as well.
    Craig

  • Quality Certificate Report for Vendor

    Dear Sir,
    I need a help from your end. I need a program or logic, where I can put the vendor ID,  and get all the Quality certificate details of that particular vendor.
    Thanks & Regards,
    Kuntal

    Sir,
    Client is happy with QC55 & I have also provided the MCVA. Thanks for you kind help.
    Right now it is OK.
    Thanks & regards,
    Kuntal

  • Error while executing the transaction QC22 (Quality Certificate for Batch)

    Hello Friends,
    While executing the transaction QC22(Quality Certificate for Batch), after giving the Batch Number and Customer Number, when i am executing it , system is throwing the error message as "Not all data was found for characteristic 90139982 in profile D80D8".
    Message no. ZQ010
    Diagnosis
    Not all data was found for characteristic 90139982, referenced as number 0030 in certificate profile D80D8. The missing data could be the short text, specifications, or results.
    System Response
    The missing charactertistic will not be printed on the certificate,
    Procedure
    Review the settings for data orgin of the short text, specifications, and results, and adjust accordingly.
    One more thing i would like to add here as against the same batch in april we had taken the print of COA (Quality Certificate) through the transaction QC22. But now we are trying to do that than system is thrown above mentioned error.
    As i am new in QM, kindly explain we were to maintain the certificate profile.
    Waiting for the experts inputs.
    Thanks and Regards,
    Jitendra Chauhan

    Hi
    Try with QA33 you may have display authorization,  or check in MB51 on the base of material and batch you can find the lot number generated, then go to QA03 and check the result, if you want to validate the characters check with the inspection plan, the characters entered in the inspection plan and the characters in the concerned certificate profile.
    Regards
    Naveen.
    Edited by: vaddapalli naveen on Jul 1, 2010 1:57 PM

  • Quality Certificate for Outgoing (Delivery)

    Dear QM Gurus,
                Here I am having one scenario where I need to print test certificate for delivery considering inspection characteristics of a finished material and semi finished material at different BOM levels.
    Ex:
    Finished Material :           FERT001
    SemiFinished Materials :  HALB001, HALB002 & HALB003.  
    Raw Materials:                ROH001 and ROH002
    Process: FERT001 produced using  HALB003 Produced using HALB002 produced using HALB003 Produced using ROH001 and ROH002       
         At HALB003 we are going to capture some characteristics and FERT001 I will capture some other characteristics, Now at the time of delivery I want to print both(FERT001 and HALB003) inspection characteristics results in Certificate.
        Except FERT001 for all other materials batch is maintaining(No batch Characteristics) for tracking purpose.
        I tried some standard procedure like assigning both material in quality certificate and all MICs relevant for both materials. Result origin and inspection spec origin as 03 and Material sort no as 2 where i maintained this material in Materials sequence.
       With all the above mentioned settings I tried but I con't able to print the characteristic results of HALB003 in test certificate I can able to get only FERT001 Insp Characteristics only.
      Please help me in getting it done, it is critical requirement for our client.
    Thanks and Regards,
    Krishna Mohan.NSL

    just a idea,
    use batch dervivation to get all HALB char data into FERT batch abd then print the delivery of that batch. try and come back

  • Which tables are used for Quality Efficiency calculation of OEE report ?

    Hello,
    We're confirming OEE report behavior.
    I'd like to know OEE report and ME table specification.
    Which tables are used for Quality Efficiency calculation of OEE report ?
    According to I know, the definition of Quality Efficiency is (complete qty) / (start qty).
    For this calculation, does OEE report just use qty_started and qty_completed of PRODUCTION_LOG table?
    If any other tables/columns/logic are implemented, your information is appreciated.
    Best Regards,
    Takahiro Uesugi

    hi
    Go to BSIS & BSAS
    BKPF
    SKA1
    SKAT
    SKB1
    Regards
    Roobal

Maybe you are looking for