Tandberg Codian MCU 4505 integration with Microsoft Lync server 2010

Hi,
We are trying to integrate Tandberg Codian MCU 4505 with Microsoft Lync server 2010.
We do not have any VCS in the setup.
If anybody has tried it before, please suggest configuration to be done on Tandberg Codian MCU 4505 and Lync server.
Regards,
RN

Hi,
so, i have the same environment. Lync 2013 and a cisco 1000V router on esxi with VRFs.
here is m config:
vrf definition Mgmt-intf
address-family ipv4
exit-address-family
address-family ipv6
exit-address-family
voice vrf Mgmt-intf
voice service voip
no ip address trusted authenticate
address-hiding
media disable-detailed-stats
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
  bind control source-interface GigabitEthernet0
  bind media source-interface GigabitEthernet0
  listen-port non-secure  5066
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class codec 2
codec preference 1 ilbc
codec preference 2 g722-64
codec preference 3 g711alaw
codec preference 4 g711ulaw
interface GigabitEthernet0
vrf forwarding Mgmt-intf
ip address 172.16.1.164 255.255.255.0
negotiation auto
dial-peer voice 15 voip
tone ringback alert-no-PI
numbering-type unknown
preference 1
destination-pattern 4.
rtp payload-type comfort-noise 13
session protocol sipv2
session target ipv4:172.16.2.207:5068
session transport tcp
voice-class codec 2
dtmf-relay rtp-nte
dial-peer voice 17 voip
numbering-type unknown
preference 1
destination-pattern 7.
rtp payload-type comfort-noise 13
session protocol sipv2
session target ipv4:172.16.1.32:5060
session transport udp
voice-class codec 2
dtmf-relay rtp-nte
gateway
timer receive-rtp 1200
sip-ua
keepalive target ipv4:172.16.2.207:5068 tcp
172.16.1.32 - Asterisk with a extensions on it.
172.16.2.207 - Lync 2013 mediation server with other extension on it
i can call from Asterisk extension via router and to Lync extension.
i cannot call from Lync to Asterisk.
TCP session with the router from Lync on port 5066 does not come up. three way handshake seems to come up.
strange. lync person seems to configured everything correctly
any thoughts?

Similar Messages

  • Uc500 integration with ms lync server 2010

    Hi,
    I’m integrating UC500 with lync server 2000, I’ve achieved to make UC500 users to call lync users and vice versa. But lync users are not able to dial pstn or external numbers through UC500. When I debug UC500 on dialling from lync I can see the incoming call exactly as it should be, its also hitting the correct dial-peer but the call drops and does not go through.
    Can you help me on this please?
    Regards

    Hi Muhammad,
    Please attach "debug ccsip messages" and "debug ccsip error" output for the failed call together with the UC500 configuration.
    If you use ISDN connection to reach PSTN also include "debug isdn q931".
    Cheers,
    Boris

  • Groupware integration  with microsoft exchange server

    I have a query regarding Groupware integration with microsoft exchange server.whether we require IIS server and microsoft exchange server on the same machine for groupware integration.or they can be on different machines.
    thanks,
    Pramod

    hi,
    We actually implemented integration of SAP with microsoft exchange server. It is not necessary for server and IIS to be in the same machine.
    regards,
    Ganesh.N

  • Problems launching Microsoft Lync Server 2010 Control Panel

    Just finished setting a new Lync 2010 environment.  I was able to get passed some errors with the Archiving and Monitoring stores.  I ended up removing those server roles to get the setup completed.  Now, when I try launching the Microsoft
    Lync Server 2010 Control Panel I get the following error:
    Could not load type 'System.ServiceModel.Activation.HttpModule' from assembly
    'System.ServiceModel, Version=3.0.0.0, Culture=neutral,
    PublicKeyToken=b77a5c561934e089'
    Description:
    An unhandled exception occurred during the execution of the current web
    request. Please review the stack trace for more information about the error and
    where it originated in the code.
    Exception Details:
    System.TypeLoadException: Could not load type
    'System.ServiceModel.Activation.HttpModule' from assembly 'System.ServiceModel,
    Version=3.0.0.0, Culture=neutral,
    PublicKeyToken=b77a5c561934e089'.
    Source Error:
    An unhandled exception was generated during the execution of the current web request.  Information regarding the origin and location of the exception can be identified using the exception stack trace below.
    If the Stack Trace is needed I will post, any help would be greatly appreciated in solving this error. 
    Thanks in advance,
    Hector

    Were you playing with .NET versions at all? 
    https://support.microsoft.com/kb/2015129?wa=wsignin1.0
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
    SWC Unified Communications
    This forum post is based upon my personal experience and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

  • MS14-055 security update for Microsoft Lync Server 2010

    hello
    after applying this security update do I need to Apply it to the back end database? or is that just when regular patches are applied?

    Hi totalnet32,
    From http://support.microsoft.com/kb/2493736, we know that
    "After you install the update for the Core Components server role on a Lync Server 2010 Enterprise Edition front end server, the updated SQL database files are dropped to the computer that has the Core Components server role installed.This
    also applies to a Lync Server 2010 Standard Edition server. To apply the database changes, run the following cmdlets:
    Install-CsDatabase -Update -ConfiguredDatabases -SqlServerFqdn <EEBE.Fqdn> -UseDefaultSqlPaths
    2982388
    (https://support.microsoft.com/kb/2982388/            )    
    MS14-055: Description of the security update for Microsoft Lync Server 2010 (Response Group Service): September 9, 2014
    2982385
    (https://support.microsoft.com/kb/2982385/            )    
    MS14-055: Description of the security update for Microsoft Lync Server 2010 (Security update for Standard/Enterprise edition Server): September 23, 2014
    There's no Core Components server role update, as far as my experience, the DB update is not required.
    And I suggest that reboot the Lync Servers once after the updates have been installed.
    Best regards,
    Eric

  • C:\Program Files\Microsoft Lync Server 2010\Deployment\ directory missing.

    Hi Guys,
    We were trying to “Install the Mobility Service and autodiscover Service” on lync 2010 frontend server, for which we have downloaded the “McxStandAlone.msi” and placed in
    “C:\ProgramData\Microsoft\Lync Server\Deployment\cache\4.0.7577.0\setup” location.
    As per the document, to execute this we have to run the bootstrapper.exe from the lync powershell at the following location
    “C:\Program Files\Microsoft Lync Server 2010\Deployment\Bootstrapper.exe”
    But “Deployment folder and bootstrapper exe” are not present in mentioned location.  
    So is there any workaround for this ? 
    Thanks and Regards, 
    Ankit 

    Did you happen to install Lync on another drive? Maybe D:?
    Also try to run the Lync Deployment Tool and click "Install or Update Lync Server System" and rerun "Setup or Remove Lync Server Components". This should do the same thing as running the bootstrapper.
    If this helped you please click "Vote As Helpful" if it answered your question please click "Mark As Answer"
    Georg Thomas | Lync MVP
    Blog www.lynced.com.au | Twitter
    @georgathomas
    Lync Edge Port Check (Beta)
    This forum post is my own opinion and does not necessarily reflect the opinion or view of Microsoft, its employees, or other MVPs.

  • Oracle HRMS Integration with Microsoft Exchange Server 2007

    I would like to know if it is possible to integrate Oracle HRMS 11.5.10.x with Microsoft Exchange Server 2007 using Microsoft Identity Lifecycle Management (ILM) 2007?
    Has anyone ever come across something like this and successfully achieved it? Does anyone know of a step-by-step guide (or forum discussion) to achieve this?
    Response(s) will be highly appreciated.

    hi,
    We actually implemented integration of SAP with microsoft exchange server. It is not necessary for server and IIS to be in the same machine.
    regards,
    Ganesh.N

  • Navigation to webpage was canceled when opening Microsoft Lync Server 2010 Control Panel

    Ok, yes I know there are many threads with similar titles, but my problem is different in that it doesn't happen every time.
    The first time I access the Control Panel I get the error:
    "Navigation to the webpage was canceled
    What you can try:
    Refresh the Page"
    Clicking Refresh the Page works, kind of.  It brings up the admin console, but I get the spinning lights, which eventually resolves to an error at the top of the page that reads: "An operation failed.  Network communication failed.  Verify
    your connection and try again." 
    Then if I click to other parts, things seem to be fine for the most part, I sometimes see the Network error, and often it is slow.
    Port 443 is running through an HLB and this is setup exactly like my other Lync cluster, which doesn't have this issue.  Internal web services URL is lynccontent and points to HLB VIP.  Admin redirect is lyncadmin and points to HLB VIP.
    Going to the /cscp page of each FE or of the pool from IE works every time, but lyncadmin seems to have the same issue (at least on FE1).
    Any thoughts?

    Hi,
    Could you perform the followings:
    Make sure there're no duplicate records in the DNS Servers
    Flush your DNS Cache at the Server & Client
    Refresh any DNS Cache at the HLB (if any)
    When the error appears, right click on the console and provide a screenshot on this
    If you suspect that FE1 is the culprit, had you tried turning it off and monitor the situation?
    Thanks!
    James Ooi MCITP Lync Server 2010 | Blog: http://jamesosw.wordpress.com | Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial
    to other community members reading the thread

  • Tring to install Security Update for Lync Server 2010 (KB2982388) ...patch failed to install

    Hi
    Idenitfied the lync security update issue below on server....
    Worker process exited prematurely.  The process will be automatically restarted.
    Process: 'C:\Program Files\Microsoft Lync Server 2010\Server\Core\RtcHost.exe'  Exit Code: E0434F4D!_HRX! (No Message Text Found!_HRM!).
    The KB2982385 has tried to installed and failed 7 times....and as such my lync edge server is down.
    Found solution:
    http://www.microsoft.com/en-us/download/details.aspx?id=44080&fa43d42b-25b5-4a42-fe9b-1634f450f5ee=True
    Downloaded patch and then ran lyncserverupdateinstaller...however it doesnt recognise that there is a patch to be deployed or a component to update.
    Further running the msp by itself results in:
    The upgrade patch cannot be installed by the windows insteller service because thje program to be upgraded may be missing or the upgrade patch may be a different version...
    Please advise how i can get this issue resolved.

    Hi,
    Did you try to download and install the update manually?
    Here is a similar case below, it seems something wrong when updating through Windows Update automatically.
    http://social.technet.microsoft.com/Forums/en-US/dea0e9e2-8375-4599-b4cc-7a0cd45cd9de/kb-2982385-has-broken-my-edge-servers?forum=ocsedge
    You can refer to the step of “Step 1: Install the cumulative updates”, choose “Method 3 Manual install” in the link below:
    http://support.microsoft.com/kb/2493736
    Best Regards,
    Eason Huang
    Eason Huang
    TechNet Community Support

  • Integration of CUCM 8.5 with Microsoft Lync 2010 issues

    Hi All,
    We have integrated CUCM 8.5 with Microsoft Lync 2010 (both Mediation and front end server on Virtual machine on same location) on lab environment, and which is working perfectly on both ways (Two way calls with no issues). But, when we tried configuring the same on live environment, we have no two ways calling between Lync client and IP phone endpoints. Our Mediation and front server are in U.S and CUCM 8.5 cluster are in India and lync clients are in India region, connected via MPLS link and all the traffic ports are open. The following are the configuration on both sides:
    CUCM side:
    •- Created Direct SIP trunk with MTP enabled.
    •- Assigned Mediation server IP address to Port 5068.
    •- TCP enabled
    LYNC Side:
    •- Followed the steps from Cisco Lync integration document through cisco website.
    Are they any other configuration requires, when the servers are in different location?

    You configure the CUCILync client as a shared line.  You then tell the CUCILync client what to control either the desk phone or use the CUCILync client itself.  When CUCILync controls the phone it is not registered in CUCM.  CUCILYNC will still give a screen POP when the desk phone is controlled.

  • ECC 6.0 integration with Microsoft Dynamics CRM

    Hi All
    I am working on a ECC 6.0 integration with Microsoft Dynamics CRM. I need to send the customer master data, va01/va02, vl01n/vl02n/ vf01/vf02 to CRM system. One option I have is to send in the form of IDOC with TRFC - TCP/IP. But looks like this needs a middleware like Biztalk.
    Is there a way I can send this data using a Internet service in ECC 6.0 ??? As this would cut the cost of the Biztalk.
    I really appriciate your thoughts on this. We don't have XI either.
    Thanks a lot
    Van

    HI Van Dan Jan,
    We have just implemented integarion of SAP with Microsoft stack (Microsoft CRM, Share point and Axapta), But in all integration BizTalk as a middleware used.
    There is two way requirements :
    1. whenever Most of the control are at the Microsoft level like : Customer creation, Creation of orders, which need to be synchronus activity we have used RFC which internally calls BAPI. (So SAP adapter Configured at BizTalk). and whenever Biztalk receives request file from CRM or share point to there location they call SAP RFC's.
    2. When DATA is needed from SAP to microsoft stack like to syncronize the missing transaction like customer pad and all.
    Scheduled job at BizTalk end which call SAP to get the DATA via RFC mode :
    In SAP we have two things
    1.  if DATA size is small (below 2 MB) like  in last 1 hrs what are the sales contract created in SAP that need to updated in Microsoft other system than Biztalk will trigger a job at 1 hr interval or on deemand to get the detail which directly we pick from data base or using BAPI to get the detail via RFC.
    2. If Data Size is large (more than 2 MB)  like total transation happened in a day for all customers: then we wriiting the data in OS or application server  and that job also get initiated from Biztalk end by sending any parameter to SAP.
    advantage of using BizTalk is most of the control you can give it to them so they can run there job on deemand basis.
    There is a something known as web service we can use to avoid Interfacing tool, but I dont have much Idea about that,
    and  please check how many interfacing point is there with SAP in your project, because if Interfacing points are more then I think it is not good to write a web services for so many things.
    do let me know if you need further information.

  • SAP Workflow integrated with Microsoft Outlook

    Hello All,
    I have the following question. When an work item comes in the SBWP inbox, as soon as the work item is executed by the user
    the workitem disappears from the SBWP. Now my question is if SAP Workflow is integrated with Microsoft Outlook (so that email containing the work item as a link reaches Outlook), is there a way to make the email disappear from the Outlook as soon as the SAP work item is completed.
    Can someone throw some light on the same.
    Thanks,
    Sachin

    Hi,
    Duet workflow scenario is available. SAP Application sends workitem to Duet Server and Outlook client has Duet add-in. You need Duet Server and user license.
    Also SAP MAPI Service Provider is available. You can access SAP Inbox items from your outlook client. I think SAP MAPI Service provider is free.
    Regards,
    Masa

  • Share desktop with Microsoft Lync

    Hi guys,
    I was wondering if anyone knows how to share desktops with Microsoft Lync peers?  I would like to be able to view as well as share my desktop.  I have a working pidgin sipe configuration, but haven't come across any documentation indicating pidgin can work like lync (share/view desktops).
    Any other ideas as to what I might try?
    Thanks,
    Walter

    Thanks Holger. That blog is a bit over my head but also helpful. I had my network guy check our configuration on our Edge and 3478 UDP is open in both directions for the A/V service and IP so not sure what the issue is. As for our firewall, anything over
    1024 should be allowed out.
    In this particular incident, Microsoft sent me the meeting request and I initiated the request by clicking on the link in the email launching my locally installed Lync client. Microsoft tech then made me the presenter at which point I had the option to share
    my desktop. It's at this point that the connection drops.
    I turned on Centralized logging and clicked on the meeting invite from Microsoft one more time. The tech at the other end was not there of course but I did generate some traffic that I was able to view using Centralized logging. I determined that the traffic
    is most definitely going through the Edge server at least in this situation.
    I did find an error in the log that was interesting and have a question on. The error read:
    ms-diagnostics: 1017;reason="Cannot route From and To domains in this combination";summary="Cannot route between the source and destination domains because
    partner discovery is not enabled";external-domain="microsoft.com";external-type="domain-type-remote";internal-domain="mydomain.com"
    ";internal-type="domain-type-local";source="My edgeserver.com"
    ms-edge-proxy-message-trust: ms-source-type=EdgeProxyGenerated;ms-ep-fqdn=fqdn of my Edge;ms-source-verified-user=verified
    I took a look in Control Panel and under Federation and External Access --> Access Edge Configuration -->Enable partner domain discovery is NOT enabled. I am thinking
    I should not have to have a Federation with Microsoft to have a Lync meeting and share my Desktop, correct?
    I don't think turning this option on is a good thing because it looks like it will automatically establish a Federation with anyone and you lose control over which companies you want to Federate with.

  • DPM integration with Microsoft Azure backup queries

    Hi All,
    We have made the test set-up environment with installed the below details
    DPM 2012 R2 on VM (Windows 2012 R2)
    We are using a raw disk of 200 GB for disk staging.
    DPM integrated with microsoft azure.
    Able to take file backup and databases backups from DPM and can perform the restore from Disk staging as well as from azure
    Queries:
    Will DPM support deduplication for exchange (2007,2010,2013) databases and for sql databases (2000, 2005,2008,2012,2014) ?
    on the wire compression is enabled but how to verify that?
    Is it possible to mount the raw disk to some other drives except local Disk (C:\)
    How to do granular recovery in DPM 2012 R2 for microsoft exchange?

    Chris,
    Really sorry for the delay in response.
    I found lots of warning messages in the logs like below one:
    578    788    24-Apr    20:49.7    18    readeriterator.cpp(587)    [000000002435A140]    0BABF215-19DF-49F5-B8DF-7210CB336DD5    NORMAL  
     "CFileReaderIterator:GetNextFileReader -> Skipping Hardlink with Physical FilePath: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy34\Windows\WinSxS\amd64_microsoft-windows-i..l-keyboard-0001042b_31bf3856ad364e35_6.2.9200.16384_none_f8e4c1f6d2951dd3\KBDARMW.DLL,
    Logical FilePath: \\?\Volume{bd3973d0-2f82-11e4-93f6-806e6f6e6963}\Windows\WinSxS\amd64_microsoft-windows-i..l-keyboard-0001042b_31bf3856ad364e35_6.2.9200.16384_none_f8e4c1f6d2951dd3\KBDARMW.DLL"
    578    788    24-Apr    20:49.7    18    readeriterator.cpp(587)    [000000002435A140]    0BABF215-19DF-49F5-B8DF-7210CB336DD5    NORMAL  
     "CFileReaderIterator:GetNextFileReader -> Skipping Hardlink with Physical FilePath: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy34\Windows\WinSxS\amd64_microsoft-windows-i..l-keyboard-0001042e_31bf3856ad364e35_6.2.9200.16384_none_fa395780d1ba2b68\KBDSOREX.DLL,
    Logical FilePath: \\?\Volume{bd3973d0-2f82-11e4-93f6-806e6f6e6963}\Windows\WinSxS\amd64_microsoft-windows-i..l-keyboard-0001042e_31bf3856ad364e35_6.2.9200.16384_none_fa395780d1ba2b68\KBDSOREX.DLL"
    So, I'm checking with concerned guys in here about this. I'll get back to you once I receive any update from them.  However, if it very urgent and need immediate assistance, I suggest you to open up a support ticket with Azure technical Support team
    as they will be able to provide you very quick solution.
    Regards,
    Manu

  • CCME integration with Microsoft Business Contact Manager

    Hi,
    Can anyone tell me, if a CCME can be integrated with Microsoft BCM such that when a call comes in details of the client pop up, should they exist in the Business Contact Manager.
    Finding exact information is like find a needle in a hay stack.
    Regards
    LN

    Hi Swinster,
    Apologize for the late reply.
    What is your current situation? As JS2010 stated, also in this KB article:
    http://support.microsoft.com/kb/2101557
    During the 'Specialize phase' of Sysprep, Sysprep.exe looks at the Last Modified Date of the ntuser.dat file for each user profile to determine which user profile to copy to the default user profile. However, the earlier cleanup functions of sysprep.exe
    loads each Ntuser.dat file to make security ID (SID)generalizations. You cannot predetermine which user profile will be copied if more than one user profile exists.
    How about we skip the copyprofile option?
    Further, see if the following article would help to customise the user profiles settings:
    Configuring Default User Settings – Full Update for Windows 7 and Windows Server 2008 R2
    http://blogs.technet.com/b/deploymentguys/archive/2009/10/29/configuring-default-user-settings-full-update-for-windows-7-and-windows-server-2008-r2.aspx
    Or we may consider seek help at the office outlook forum for the BCM deployment.
    Best regards
    Michael Shao
    TechNet Community Support

Maybe you are looking for