TC shows in AirportUtility on 1 pc and not the other

I've been racking my brain all night, searching everywhere, trying everything and I've given up. I have 2 xp laptops. My home laptop is connected no problem and I'm copying files over right now. My work laptop can't pick up the TC in the Airport Utility even though I'm connected through it as a router and I'm writing this post via its internet connection. Funny thing is I can go to 'File | Configure Other', type in the ip address 10.0.1.1 with my password and the TC pops up and I can change settings, etc. So I'm kind of connected, but not really.
How can I get to the hard drive so I can map it and copy files to it?

My guess is that it has something to do with the fact that when I logon to my work laptop I'm signing onto to my work domain. I need to do that so that I can do work on it in the evenings, but I want my TC to backup my data at night. Any thoughts?

Similar Messages

How can I transfer photos from an IPhone 5 to an IPad 2 using a cable. I have tried using the lightning to firewire adapter with my current lead but this only seems to allow a download from the Ipad to the Iphone and not the other way around.

How can I transfer photos from an IPhone 5 to an IPad 2 using a cable. I have tried using the lightning to firewire adapter with my current lead but this only seems to allow a download from the IPad to the IPhone and not the other way around.

The devices are not designed for transfer of that kind. Use Photo Stream as suggested by another poster, or transfer photos to your computer (a good idea anyway since they will be lost if your device needs to be reset), then use iTunes to sync them to the other devices.

I bought a 5th Gen Touch. I use iTunes 12 on two computers. One computer allows me to drag and drop. The other does not.The one that allows it has problems. Any idea as to why I can drag and drop on one and not the other. Both are authorized.

I bought a 5th Gen Touch. I use iTunes 12 on my two computers. I first connected the Touch to my desktop and it allows me to drag and drop mp3 files from my old Classic, which is backed up to a directory. Unfortunately, that computer has gone down before I got a chance to fill the Touch. I have the files on another computer but when I connect the Touch to it, it doesn't allow me to drag and drop the files. I have iCloud set on both systems and I have manual management check marked. I'm not understanding why it allows drag and drop on one PC and not the other when they are both set the same way. My question? What do I need to do to be able to drag and drop in iTunes 12? I didn't do anything special on the computer that allows it so I am at a loss.
Thank you!

Oh, also want to add that the PC I'm currently using is:
Windows Vista Home Premium Service Pack 2
My other PC was:
Windows 7 Ultimate
My MacBook is:
Max OSX 10.5.something (the last update available for it. .8 maybe? haha)
Not sure if this stuff is important, but I thought I'd add it.

I just synced my iPhone and lost all the info in notes from my phone. It was replaced with whT was on my iMac how do you make the sync go from phone to desktop and not the other way around

I Just synced my iPhone and lost all the info in notes I had on the phone. How do you have the info sync from phone to desktop and not the other way around as I usually make contact changes etc on my phone. I would then like to be able to sync that info from desktop to ipad thanks

It does make sense. The iPhone is a one-person device and just syncs to one computer.
The way it should work is as follows:
Old computer content ---> New computer
New computer <---> syncs to iPhone
But the way you are trying to operate sounds like:
Old computer content ---> iPhone
... and ...
New computer content <---> iPhone
So simply move your old stuff (either directly from iTunes, or from a computer backup) to the new computer, have it all there, then sync your iPhone to the new machine.

I have CS6 and CC installed on my mac when I'm using CS6 and use bridge CC activates how can I set this to only work on one and not the other

I have CS6 and CC installed on my mac when I'm using CS6 and use bridge CC activates how can I set this to only work on one and not the other

If you want Bridge CS6 to open when using Photoshop CS6, you must quit Bridge CC.
Then File menu > Browse in Bridge will bring up Bridge CS6.
If Bridge CC is already open, The File > Browse in Bridge for Photoshop CS6 will use Bridge CC and Bridge CS6 will not open.
I hope that's the answer you were looking for.
Gene

When printing from aperture my margins are unequal, even if i set my margins they come out bigger one side and not the other. i am using a macbook pro running osx lion and printing with a canon pro 9000

when printing from aperture my margins are unequal, even if i set my margins they come out bigger one side and not the other. i am using a macbook pro running osx lion and printing with a canon pro 9000.
please can anbody help or advise?

You didn't mention any color calibration being done on your monitor. This is an essential part of any color-correct workflow. What are you using to calibrate your monitor (and your printer)?
Print profiles (for soft-proofing as well as printing) are for specific combinations of paper & printer. The nine you have are each, most likely, for a common paper (perhaps mfr'd by Canon) to be used with your printer.
I don't know what you mean when you say "I choose a high standard print option".
Have you read the User Manual chapter on printing?
Printing Your Images
There is also a good appendix on calibration:
Calibrating Your Aperture System

I have an 8GB ipod touch and suddenly I'm able to access only the "sent" mailbox of Mail and not the other mailboxes. I turned on and off. I connected it to MacBook but still I can't access the other mailboxes.

i have an 8GB ipod touch and suddenly I'm able to access only the "sent" mailbox of Mail and not the other mailboxes. I turned on and off. I connected it to MacBook but still I can't access the other mailboxes.

- Try resetting the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Can you access the mail on another device?

Why can one mac access the internet and not the other?

Hi I have just installed a 2nd generation Airport Express base station. I have setup a network and I can connect to it to access the web. Here's the rub, only my Macbook Pro can connect. My Macbook Air cannot connect? A weird error message says (translated from Swedish): Airport has the selfapplied/selfselected IP adress 169.254.67.130 and will not be able to connect to the internet.
Why can one mac access the internet and not the other? Is there something simple that I can do to get more macs to be able to use my Airport Express to access the internet?
Tech details:
Airport Express 2nd generation (just purchased) model 1392
Macbook Pro running 10.8.2
MacBook Air running 10.6.8

It seems the Airbook assigns a dummy IP address so somehow it doesn't reach and receive an IP from the Express. I deleted the previous Express setting restarted the Air connected again, restarted the modem, restarted the Express nothing....
I spoke to the internet provider and the cable modem does not require any username or pw. from the modem to the cable it's one public ip, pure internet is flowing from the modem to the Express but the express doesn't seem to assign any IP address apart from the one assigned to the Macbook Pro.
Do you need a screendump of the settings on the functioning Mac or the faulty one? What settings are you interested in i.e. which tab should it shot?

PDF email only sends the top page and not the others

I have created a real estate brochure in Pages. I have tried to email it as a PDF. When it arrives at its destination there is only one page and not the three which are in the brochure. Why is this? I sent this in Pages format I have all the surrounding editing paraphernalia. It does not look very professional

Are you sure this is what is happening?
Only the top page is shown in the eMail. Save the pdf or double click on it so it open in Preview or Acrobat Reader and you should see all the pages.
If you want people to see multiple pages in the email, split the .pdf up into individual pages, then add them to the eMail.
Peter

Why packets are being translated by one route-map and not the other?

Hi,
I have 2 NAT rules, each with a route-map to determine which packets are translated. What I don't understand is how to control which NAT rule is applied first..?
In my config, the first of the following rules is applied first, and then the other. I would like to have it the other way round, the second being applied first, and the first being applied second.
ip nat inside source route-map NAT_INTERNET_ACCESS_RMAP interface GigabitEthernet0/1 overload
ip nat inside source static 172.16.101.1 10.10.11.1 route-map NAT_RADIANZ_PIXACCESS_RMAP
The reason why I want it this way round is because the first rule NAT's almost everything so that I can access the Internet. The second rule NAT's specific traffic to a different address.
If I want traffic to be NATTED according to the second rule, I have to deny traffic in the first associated ACL, and permit it in the second ACL. That means I basically have to configure each ACL each time I want packets to be matched by the second NAT rule - there must be a better way of doing it!!!
Any help would be most appreciated.
Many thanks,
Michael.

Hello, here's the basic (shortened list). If I want packets to be matched by NAT_RADIANZ_PIXACCESS_ACL I have to put a deny in NAT_INTERNET_ACCESS_ACL. If I could make sure that the first list is used first, and then anything left over compared against the second, then it would make life/editing much easier...
Cheers,
Michael
ip nat inside source route-map NAT_INTERNET_ACCESS_RMAP interface GigabitEthernet0/1 overload
ip nat inside source static udp 10.10.11.1 500 10.10.11.1 500 extendable
ip nat inside source static udp 10.10.11.1 4500 10.10.11.1 4500 extendable
ip nat inside source static 172.16.101.1 10.10.11.1 route-map NAT_RADIANZ_PIXACCESS_RMAP
ip access-list extended NAT_INTERNET_ACCESS_ACL
remark Traffic to Branch A (over VPN)
deny ip 172.16.101.0 0.0.0.255 192.168.1.0 0.0.0.255
remark Traffic to Branch B (over VPN)
deny ip 172.16.101.0 0.0.0.255 172.16.0.0 0.0.0.255
deny ip 172.16.101.0 0.0.0.255 172.16.1.0 0.0.0.255
deny ip 172.16.101.0 0.0.0.255 172.16.2.0 0.0.0.255
deny ip 172.16.101.0 0.0.0.255 172.16.3.0 0.0.0.255
remark Traffic to Cust A (over VPN)
deny ip host 172.16.101.1 host 192.168.0.1
deny ip host 172.16.101.2 host 192.168.0.1
remark Traffic to Cust B (over VPN)
deny ip host 172.16.101.1 host 192.168.0.2
deny ip host 172.16.101.2 host 192.168.0.2
remark Traffic to Cust C (over Radianz VPN)
deny ip host 172.16.101.1 host 192.168.0.3
deny ip host 172.16.101.2 host 192.168.0.3
remark Traffic to Cust D (over Radianz VPN)
deny ip host 172.16.101.1 host 192.168.0.4
deny ip host 172.16.101.2 host 192.168.0.4
permit ip any any
ip access-list extended NAT_RADIANZ_PIXACCESS_ACL
remark Manangement Traffic to Cust C
permit icmp host 172.16.101.1 host xxx.xxx.xxx.xxx
permit icmp host 172.16.101.2 host xxx.xxx.xxx.xxx
permit tcp host 172.16.101.1 host xxx.xxx.xxx.xxx eq 22
permit tcp host 172.16.101.2 host xxx.xxx.xxx.xxx eq 22
remark Manangement Traffic to Cust D
permit icmp host 172.16.101.1 host xxx.xxx.xxx.xxx
permit icmp host 172.16.101.2 host xxx.xxx.xxx.xxx
permit tcp host 172.16.101.1 host xxx.xxx.xxx.xxx eq 22
permit tcp host 172.16.101.2 host xxx.xxx.xxx.xxx eq 22
route-map NAT_RADIANZ_PIXACCESS_RMAP permit 10
match ip address NAT_RADIANZ_PIXACCESS_ACL
set ip next-hop 10.10.11.14
route-map NAT_INTERNET_ACCESS_RMAP permit 40
match ip address NAT_INTERNET_ACCESS_ACL
set ip next-hop xxx.xxx.xxx.xxx

I changed my e-mail address, but everytime I try to do an update on my imac it shows my OLD e-mail address and not the one that I am logged in with, I have tried to rectify this and cant.

can you please help me to sort this, I changed my e-mail address from [email protected], I have delleted this e-mail now. My new one, [email protected] is now my registered one but everytime I try to do an update in itunes it shows my old e-mail address and it wont use my new one, I own an imac, ipad and iphone, my iphone and ipad are perfectly fine working with [email protected] but not my imac, can you please help me to sort this out. x

Hi Florafromco,
You can view your iTunes Store account and request assistance by following the instructions below:
iTunes Store & Mac App Store: Seeing your purchase history and order numbers
http://support.apple.com/kb/ht2727
I hope this information helps ....
The following article will provide a little more information regarding using multiple Apple ID's:
Using your Apple ID for Apple services
http://support.apple.com/kb/HT4895
I hope this information helps ....
Have a great day!
Have a great day!
- Judy

Ask your question.I installed the app" Find my phone for my Ipad. But I also installed that app on my Iphone. but the Iphone app still just shows where my Ipad is located and not the phone, how can I get then both to show location?

I installed the App" find my Iphone on my Ipad.. its working well.
But I also need to be able to track my Iphone if lost... I also have the app on my Iphone but when I click on it to find my phone it is showing me where my Ipad is... how can I get it to show my Iphone also? the chances of me losing my Ipad are less then my Iphone.But I need to be able to trac both.

How was your wife using the Find My iPhone app from a Samsung phone? But, that question aside, your wife should educate herself on how GPS works, especially on a cell phone. GPS signals can be interfered with by trees, buildings, clouds. Off by several miles would be unusual, though.
If your wife is tracking your cell phone and not believing what you tell her, you may want to consider counseling as there are some very serious issues that go way beyond the technology.
Best of luck.

We have two users on 1 computer tools, history, etc show up on one user screen but not the other how do i fix this

We have one computer in our home and two user accounts, his and hers. On my account at the top of the page I have file, edit, view, history, bookmarks, tools and help.
On the other account it will not show any of those topics. Its very discouraging first its there and than it dissappears so that we cannot find our bookmarks.
How do i remedy this so the same is on both user accounts.

For details of how to restore it, see [https://support.mozilla.com/kb/menu+bar+is+missing]

HT1386 How can I get local content only to sync FROM my library to my Iphone and not the other way around?

Ever since ICloud, my local Itunes library has been poluted with old music that I got rid of a long time ago.
I purchased an album from the Itunes Store App on my Iphone, listened to all the songs and decided I don't like all of them but some of them. So I went on my laptop and the album I purchased loaded into Itunes. I manually deleted the content I didn't want from my Itunes library. Once my library was set the way I wanted, I wanted my Itunes library synced into my Iphone, but instead, my Iphone's content gets re-synced back into my Itunes library and the content I once deleted tries to re-download.
It's agrivating that what was once an easy automated process is now a slow agonzing manual process. I'm considering getting rid of my phone if I can't find a remedy for this, which is the only apple product I now own.
I don't want ICloud to auto download content
I don't mind streaming the old music on my Iphone but I DO NOT want it downloaded into my phone or into my library. I like to keep ICloud and my Itunes Library seperate.
I just want to click "Sync" on Itunes, and my phone syncs EXACTLY how my Itunes library is.
Please help...

Backup, then restore the iPhone without syncing. Only the content currently in your library can be restored back to it.
Turn off all options in iTunes and on the device for automatic downloading of purchases.
In principle purchases made on the device are copied into the iTunes library when syncing. This ensures that you have the media ready to place back on it or a replacement should the device be lost, stolen, damaged, or need restoring, When you want to remove content either delete it manually from both the device & the library at the same time, or uncheck it within the library so that it is removed from the device during sync, then remove from the library later.
tt2

Why does wireless work for one laptop and not the other?

I have two laptops:
1) MacBook: 10.4.8, Airport Exteme (Firmware 1.0.46)
2) G4: 10.3.9, Airport Extreme (405.1 (3.90.0.p18)
I have the two machines sitting right next to each other in my apartment. Machine #1 has full wireless signal strength. Machine #2 barely has any wireless signal. Neither is running Interference Robustness. Any ideas why one would work and the other would not, or suggestions as to how to debug this problem?
I have tried stopping and restarting the Airport Extreme card on machine #2. I have also tried power cycling machine #2. This does not fix the problem.
A little more history: for a long time I was having problems with machine #2 dropping the wireless connection. As part of trying to work around these problems I turned on Interference Robustness on machine #2. This fixed the dropping signal problem, but left me with weak signal strength. I shut off Interference Robustnes but ever since then the signal has still been weak on machine #2.
Mac Mini Duo 1.66 GHz, 2 GB Mac OS X (10.4.6)

The base station uses a single channel which all clients must use to connect.
Have you checked the antenna connection into the card? Many people are surprised about how far the wire is actually supposed to be pushed into the card. Compare the connection with the photos in KB 108039, Properly attaching the antenna on an AirPort Extreme Card.

TC shows in AirportUtility on 1 pc and not the other

Similar Messages

Maybe you are looking for