TC with existing Airport Express network?

I have a home network using 3 AE (WEP encryption) , 1 main, 1 wds and 1 airtunes. Could I add a TC to this existing network and use it as TM for my Macbook?
Thanks

If the AirPort scan indicates a seperate network, then the printers wireless has created it`s own network, in stead of connecting to the existing one.
You said you installed drivers and support-software. According to the networking manual on
http://welcome.solutions.brother.com/BSC/public/files/dlf/doc002029/527080_NUG_ENVer0.pdf
a program called 'BRAdmin Light' would have been installed together with the drivers. This program should be used to monitor the status of the printer and to edit the networking settings.
The specific manual`s third chapter specifically mentions your printer and setting it up for wireless. Or you could check the Quick Start Guide, it should also have the necessary info.

Similar Messages

How do you add an Airport Express to an existing Airport Express network

how do you add an Airport Express to an existing Airport Express network

I assume that you are interested in using the new Express to extend the wireless range of the other.
If so, please check out the following Apple Support article.

HT5211 My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

Unless your HP printer is an AirPrint-ready device, just connecting it to the USB port of the AirPort Express base station will not make it so.
On the other hand, connecting a non-AirPrint printer to the base station's USB port it can be shared out by the base station's print server. Please see the following Apple Support article for details.

Adding new airport extreme to an existing airport express network...

i currently have a home airport network comprising two airport express units; one attached to the cable modem in the bedroom and the other downstairs in my study (extending the existing network and feeding a shared USB printer and airtunes speakers). i've recently bought an airport extreme, to improve network performance. i also plan to add a NAS in the next week or so.
ideally i'd like to situate the new airport extreme in the study, as i don't want to have to keep the NAS in my bedroom!
my question is this, if i add the new airport extreme to the existing airport network, will i see the benefit of the 802.11n connection, or should the extreme be set up as the primary base station?

... will i see slower transfer speeds (than if it was connected to the extreme) to / from the NAS when accessing it wirelessly from elsewhere in the house?
No. The transfer speed will be limited by the slowest connection, which is almost certainly your wireless connection speed.
If you buy a switch, buy a gigabit switch. Not because a slower one will limit your transfer speed, but because the Extreme is Gigabit and any newer equipment is likely to be as well. The advantage would only be relevant to the wired LAN.
The Express's Ethernet is not Gigabit but there is no reason for it to be, since it cannot connect to anything other than a slower wireless connection anyway.

How to extending the range of an existing airport express network?

I have a Dell PC (Dimension 8100) and a Dell laptop (model Latitude D620). Both use Windows XP.
I use Airport Express for wireless network - it has worked very well for the past 2 years.
I purchased another Airport Express in order to extending the range. I have tried setting it up following the instructions but have failed.
Can someone please help me understand where I could be making an error? Any help will be greatly appreciated. Thanks.

Wireless Distribution System (WDS) Setup
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the set up phase.)
Set up the AirPort Express Base Station (AX) as the WDS Main Base Station, by either connecting to the AX's wireless network or by temporarily connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
WDS Tab
- Enable this base station as a WDS: main base station (checked)
- Allow wireless clients on this base station (checked)
- Click "+" to add Remote/Relay Base Stations.
-- Select the Base Station that you want to be the WDS Remote/Relay.
-- AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.
-- Auto configure as a WDS remote base station (checked)
-- Click "OK."
- Verify that the Remote/Relay Base Station has been added to the list.
- Click "Update," and then verify the settings for the Remote/Relay.
-- Allow wireless clients on this base station (checked)
-- New network name: <verify that this is the same as the network name for the AX>
-- TCP/IP: Configure using DHCP
-- Base Station Password: <the Remote/Relay Base Station password>
-- Confirm: <same as previous step>
-- Click "OK."

I am unable to join my existing wireless network with new AirPort Express

I am unable to join my existing wireless network with new AirPort Express.
I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
Any suggestions? Thanks in advance.

Welcome to the discussion area!
It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
Power down the AX
Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
Release the reset button after 10 seconds
When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
Do you know the exact security type that your D-Link router is using? That is the key element in the process.
Open AirPort utility, click Manual Setup
Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
Click the Wireless tab
Wireless Mode....Join a wireless network
Wireless Network Name...must exactly match your D-Link wireless network name
Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
Wireless Password...must match the D-Link network
Click the Music icon to enable AirTunes
Click Update to save settings
Any luck?

Setting up Time Capsule with existing AirPort Extreme 802.11n and AirPort Express.

I already have and am using an AirPort Extreme 802.11n with an AirPort Express. I want to set up a Time Capsule 802.11n. Which is the best way to configure this?

... Which is the best way to configure this?
The answer depends on what you need the TC to accomplish. If all you need it to do is perform Time Machine backups, simply have it join your existing network in client mode. It would be if it were to connect to your existing router (presumably your Extreme), not through an "extended" wireless network (presumably your Express).
If you need the TC to "extend" your network so as to serve additional wireless clients, you can do that also. Configure it to "extend" the network created by your Extreme.
As you can see it's quite versatile.

Can I configure a wireless home network with two cable routers (both with separate connections to the same cable company)? Issue is poor signal strength even with multiple Airport Expresses added to the network.

I have a wireless home network consisting of a time capsule, two airport expresses and a cable modem. Even with this configuration I get a very weak signal in much of be condo - the walls, etc. are solid concrete. I want to see if I can add another separately connected cable modem and connect one of the existing airport express to it by Ethernet cable. If so, this would give me two wired hubs and greatly improve signal strength. I do not know if this configuration will in fact work or if I will just wind up with two, separate and unrelateable networks. Unfortunately, there is no way to run any additional Ethernet cable and I doubt simply adding more Airport Express will help. Thanks.

Try Ethernet over Power adapters.. these are very popular for your kind of environment.. being able to make non-wireless link to another area where you can setup a wireless access point.
Airport Express are not great for wireless power.. if you really have issues with wireless strength in a bad environment apple stuff is not the way to go.
The comparison chart here.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/58-2_4-ghz-dn?see=P_F
This is their worst test location you can also see averages.. the latest airport extreme.. is there a long way down.. and that is a much better wireless device than Airport Express.
The Ubiquiti power AP is small cheap and designed for precisely this duty.. useless in an apple wireless network.. you will need to run ethernet or EOP adapters back to the main router.. but if the normal omni directional antennas don't provide enough signal you can get directional ones.. I suspect you can cover your whole apartment with a pair of these and high gain directional antenna.

PROBLEM: Trying 2 add an AIRPORT EXPRESS to an already existing AIRPORT EXTREME network

I'm trying 2 add an AIRPORT EXPRESS to an already existing AIRPORT EXTREME network in my home.
I see the EXPRESS in ARPT UTILITY but when I click on "CONTINUE" or "MANUAL", the only option I'm given is to SWITCH networks, which I do not want to do.
I am using a MACBOOK PRO (MAC OS X 10.6.8)
Can someone offer me help with this?
Thanks!

Hi, I have a similiar setup. When you click onto the express, and it asks you to switch networks, it's not actually asking you to "change" networks. It's just actually switching to the xpress. When the xpress comes up, you'll input the name of your existing network, which you set up and named for the extreme. You'll have to change the extreme to "participate in a network", which is what you'll also do for the xpress. In the extreme under the WDS tab, you'll input the wds mode as "wds main". And then put a check mark in the "allow wireless clients". Where it says wds remotes, you'll input the the airport id's for the xpress's. In each of the xpress's, you'll set up as participating in a wds network. In the xpress's, under the wds tab, you'll set the wds mode to remote, and check
mark in the allow wireless clients. You'll have to input the airport id of the extreme in the wds main block. Under the internet icon on top, in internet conect tab for connect using: airport (wds), connect sharing: off (bridge mode).
Remember to insure that the express's show the same channel as the extreme, if you're using 802.11n (80211b/g compatible). Of course the security that you decide to use should also be the same.

With my Airport Express, I can join the network but not extend it.

I just bought a new Airport Express to extend the network I have setup with my Airport Extreme. At first, it seemed the Express was unable to get a correct IP address, I think because I had my DHCP server running from the cable modem, and the Extreme was just acting as a bridge. I switched the Extreme to run a DHCP server and now the Express correctly receives an IP address. However, it still tells me that it cannot extend the network, but gives no details why. It just tells me to make sure I have the correct password and to be sure I am in range.
Clearly I am in range and have the correct password, because when I switch to "join network", all works fine. Though when I do switch, I still get an amber blinking light and Airport Utility still thinks the Express is in Extend mode. When I unplug and replug the Express, then it comes up with a green light and Airport Utility shows it in Join mode and all works fine.
I am thinking there might be something wrong with my Express and am considering exchanging it. Just wondering if anyone has any ideas as to why this may be happening?
Thanks.

However, it still tells me that it cannot extend the network, but gives no details why.
Suggest that you check your AirPort Extreme to make sure that you have enabled the wireless network to be extended.
Open AirPort Utility, select the AirPort Extreme, and click Manual Setup
Click the Wireless tab below the row of icons
Just under the setting for Wireless Network name......make sure that there is a check mark next to "Allow this network to be exended".
Update to save changes
Now, try the configuration with the AirPort Express set to "Extend a wireless network"

Using an Airport Extreme with my AirPort Express as a new network?

Hello.
I am looking into buying an airport extreme as a replacement for a Netgear router that does not seem to work. I have an Aiport express already.
So let me see if I can get this straight...
I can have 6 computers (all PCs) connected (and a couple other devices like a TIVO) all connected to an airport extreme base station to the internet and 1 airport express set as a remote base station. All devices will be able to connect to the internet (3 computers plugged in via Ethernet on Airpot Extreme) and share printers/files/etc? Is there a limit to the number of computers that I can have (even if i am extending with an Airport Express?
I would appreciate any help steering me in the right direction.
Dell Laptop Windows XP

Andrew,
Yes you can do all those things.
There is a limit on the total number of connections but it is very large.
The Airport Express can be used in a number of ways.
...For music only - which is not a problem.
...Or as a wireless relay - using something called WDS. In this mode you can connect further computers to the ethernet port of the Airport Express. Or extend the wireless reach of the network.
If your ONLY use for the Express is to connect a computer, its probably better to get a wireless card for it.

Unable to create a wireless network with my airport express. Please help!

I am trying to setup a wireless network with an airport express, and connect to it with my Macbook. I just bought both of these and haven't been able to get wireless to work.
I initially plugged the ethernet cable from my cable modem into the airport express and plugged it into the wall. The macbook detected it when I opened airport utility, but the express had a flashing amber light and I was unable to connect. I then unplugged the express and re-started the cable modem. This time, the airport express showed a solid green light -which should mean that it is working correctly. However, the macbook did not find the airport express device when i searched for it using airport utility. I am able to connect the macbook directly to the cable modem, after re-starting the modem, and access the internet so at least some of the systems are go.
Any ideas? Thanks in advance for your help.
Tom

Is the issue that you cannot access the 802.11n AirPort Express Base Station (AXn) with the AirPort Utility that is running on your Win7 PC? ... or that once you have configured the AXn, the PC is unable either to find the new wireless network or can find it but cannot connect to it?

Trying to extend my airport extreme network with an airport express

I´m trying to extent my network with an airport express 802.11g.
I´ve been fallowing the guide:
http://support.apple.com/kb/HT4259
however, when I´m trying to configure the extended wifi base station ( point 8.) it won´t let me choose "extend a wireless network".
The only options I have is "create network", "join network" and "participate in a wds network".
I´ve been trying to find a solution all day.
Is there anyone out there who has hade the same problem or knows what it could be?
I´ve made sure that my base station connected to the internet through ethernet has checked the "allow this network to be extended"

however, when I´m trying to configure the extended wifi base station ( point 8.) it won´t let me choose "extend a wireless network"
Unfortunately, the older AirPort Express 802.11"g" model does not have a setting to "extend a wireless network", so it cannot be used the way that you want.
The article that you reference should be clear about this:
This article explains how to set up an 802.11"n" extended wireless network.
You need to use one of the newer AirPort Express 802.11"n" models to gain the ability to "extend a wireless network".

Can you guide me step by step in setting up airport express as a wireless extender for an existing Airport extreme network

Can you guide me step by step in setting up airport express 802.11 as a wireless extender for an existing airport extreme network?

Also check out:
Re: Need Help Networking AirPort Exp to Existing AirPort Extreme
Re: How to connect AirPort Express to existing AirPort Extreme Network...

I am trying to sync Go Rock TRMS03SR Bluetooth Portable 3D Surround Speakers with my Airport Express or iTunes So I can play Music in Multiple rooms. I have a WiFi network, my living room speakers are connected directly to Airport Express.

I am trying to sync Go Rock TRMS03SR Bluetooth Portable 3D Surround Speakers with my Airport Express or iTunes So I can play Music in Multiple rooms. I have a WiFi network, my living room speakers are connected directly to Airport Express, so how can I get the wireless bluetooth speakers to play at the same time in my bedroom?

Did you ever get this to work? My guess is that the speakers are out of bluetooth range at that distance.

TC with existing Airport Express network?

Similar Messages

Maybe you are looking for