TC7.3.0 codec fails after reset and power cycle - failed: dns lookup failed (CUCM registered)

Have a couple of codec's in the lab here that will work sometimes, and sometimes won't. They're running the latest 7.3.0 code and registering to CUCM 10.5.1SU1.  I've tried factory resetting them and get the same result.  I've manually configured the CUCM provisioning address in the system, and it immediately pulls down the correct SIP URI.  Sometimes power cycling the unit will allow it to register.  I have DNS running in this lab, A records created for all relevant hosts. 
Anybody seen this before?

This was for two C20's.  I think I found the issue. About 1 out of every 3 reset/power cycles they would work the rest they would not.
Basically, I was using DHCP to assign IP, but manually assigning DNS.  You are able to do this on most machines, but the way the Codec handles this is different. It simply appends your manual DNS configuration, including the DNS domain, to the list obtained from DHCP.  In a packet capture I was able to see where it would query all 3 DNS servers (1 manual 2 from DHCP) and it would query based on my manual domain and the DHCP domain.  It appears to round-robin the response it uses, as all DNS servers responded in one fashion or another, it just picked one to listen to.  In this manner, it had about a 33% chance of picking the correct response.
After statically assigning the IP address, the problem went away as the only DNS server was the one manually assigned.
I take this all with a grain of salt though, as our internal team is using the TC7.2.1 code and they get the DNS issue every once in a while regardless of the DHCP/DNS configuration.  There may be more to this, but I can say with certainty that using DHCP and manual DNS configuration at the same time is not recommended.

Similar Messages

  • I lost all apps after reseting and updating to IOS 7.1.1 How do I get them back?

    I lost all apps after reseting and updating to IOS 7.1.1 How do I get them back?
    I did a reset of my phone yesterday and now when I go to purchaed to download my paurchsed tabs there is nothing there.
    I see them in my ipad but they are not in my itunes app section either.
    I searched for one in the app store and it usually said "open" or had the cloud icon with the little arrow to downlaod again (free). But none of that shows up at all this time. All the apps that I'm missing show up in the pp store for me to buy again like I never purchased them at all!
    What's going on?
    I'm missing a ton of apps!
    Pleae help me!
    Gaby

    I just wanted to add this information to my post:
    I have purchaed, free and paid, 618 apps.
    In my phone apps to add to my phone when I plug it in my computer only 266 apps show up.
    In my itunes "puerchased list" only 266 show up.
    Thank God I have not updated my ipad. There I went to my "purchased" under the ALL list in the app store and there I do see my 618 apps!
    Where did my other 352 apps go? Which many were paid.
    I want my apps back.
    Thanks,
    Gaby

  • HT1459 how to permanently fix white screen after resetting and restoring

    How to permanently fix a 'White Screen" after resetting and restoring? 2nd generation ipod

    There are two different resets. The reset you did involved holding the sleep/wake & home button.
    The other reset will do exactly what it says. That reset is located in Settings - General - Reset.

  • Can't sign in in to iTunes (home sharing) after reset and update apple tv3

    can't sign in in to iTunes (home sharing) after reset and update apple tv3 

    I'm experiencing the exact same thing. Netflix, Youtube and everything else works perfectly, but I'm unable to wirelessly stream anything from my Mac, iPad, or iPhone. All on same wireless channel, all new updates, all have home sharing turned on. Never had a problem the last 2 years.

  • This mini is operating OSX 10.6.8 and trying to update to Mountain Lion but upgrade stops and a black overscreen displays saying to power off and power on.  The upgrade fails.  What's the problem?

    This mini is operating OSX 10.6.8 and trying to update to Mountain Lion but upgrade stops and a black overscreen displays saying to power off and power on.  The upgrade fails.  What's the problem?

    Hi Fred,
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at the top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair. Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)

  • My iPod touch isn't working correctly.it is displaying a white light and no matter what i try it isn't helping.tries holding the reset and power button together and tryed holding the power button in but it doesn't work. please can someone help?

    my iPod touch isn't working correctly.it is displaying a white light and no matter what i try it isn't helping.tries holding the reset and power button together and tryed holding the power button in but it doesn't work. please can someone help?

    Try the remaining items in the white-screen topic of.
    iPod touch: Hardware troubleshooting
    If not successful. let the battery fully drain and then charfe for an hour and try again.
    Frequently a white scree nis due to a hardware problem.

  • After Sleep, and power off, Lion Crash Totaly! iMac core i5 2011

    After Sleep, and power off, Lion Crash Totaly!
    I`'ve buy a iMac core i5, July 15 2011, 500gb, 4gb (upgraded to 8gb Ram).
    Transf my MBP with Snow at first iMac power on, after tranfer Snow, I buy the Lion, install and use until 2 weeks. After the first Sleep, turn Lion power off to change place. When power on, the Lion was Crashed the computer in some way that was impossible to recover or do anything. even go back the timemachine with Lion or Snow, trey clean PRAM, DVD Boot, nothing works.
    So, I put a Ubuntu LiveCD, REMOVE COMPLETE THE GUID of iMac Disk, also clean the PRAM (cmd+opt+ P + R during boot), so, the iMac was Clean and I Install the SNOW (sure).
    I just Lost the money and download time that spent to get with Lion?
    How can I have a Lion DVD for when Apple fix the LOT OF PROBLEMS?
    Have apple schedule for fix problems?

    After Sleep, and power off, Lion Crash Totaly!
    I`'ve buy a iMac core i5, July 15 2011, 500gb, 4gb (upgraded to 8gb Ram).
    Transf my MBP with Snow at first iMac power on, after tranfer Snow, I buy the Lion, install and use until 2 weeks. After the first Sleep, turn Lion power off to change place. When power on, the Lion was Crashed the computer in some way that was impossible to recover or do anything. even go back the timemachine with Lion or Snow, trey clean PRAM, DVD Boot, nothing works.
    So, I put a Ubuntu LiveCD, REMOVE COMPLETE THE GUID of iMac Disk, also clean the PRAM (cmd+opt+ P + R during boot), so, the iMac was Clean and I Install the SNOW (sure).
    I just Lost the money and download time that spent to get with Lion?
    How can I have a Lion DVD for when Apple fix the LOT OF PROBLEMS?
    Have apple schedule for fix problems?

  • DNS lookup failing on Macbook with Fios

    Hello all
    I've had Verizon Fios for over a year and had no problems connecting wirelessly to my MacBook.  Out of the blue today, both my MacBook and my brother's began to have issues accessing the internet.  Every attempt would yield the same response:
    This webpage is not available
    The server at google.com can't be found, because the DNS lookup failed. DNS is the web service that translates a website's name to its Internet address. This error is most often caused by having no connection to the Internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing Google Chrome from accessing the network.
    Here are some suggestions:
    Reload this web page later.
    Check your Internet connection. Reboot any routers, modems, or other network devices you may be using.
    Check your DNS settings. Contact your network administrator if you're not sure what this means.
    Try disabling network prediction by following these steps: Go to Wrench menu > Preferences > Under the Hood and deselect "Predict network actions to improve page load performance." If this does not resolve the issue, we recommend selecting this option again for improved performance.
    Try adding Google Chrome as a permitted program in your firewall or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again.
    If you use a proxy server, check your proxy settings or check with your network administrator to make sure the proxy server is working.
    If you don't believe you should be using a proxy server, try the following steps: Go to Applications > System Preferences > Network > Advanced > Proxies and deselect any proxies that have been selected.
    Error 105 (net::ERR_NAME_NOT_RESOLVED): Unable to resolve the server's DNS address.
    I called Verizon for support, and while their reset of my internet has allowed me to connect directly from a ethernet cord from my router, I'm still getting the same result on any attempts to connect via wi-fi.  Since Verizon decided it was a Mac issue and not a Verizon issue at this point, they pointed me in the direction of applecare, but I don't have the money to spend right now on a support call. 
    It seems that the router is connecting to the internet, and I can connect through ethernet, but their is a problem with the wireless communication between my computer and the router.  Any suggestions?

    That is a different issue. Most likely, your university IT has misconfigured their network and only tested it on Windows where little details like TCP/IP subnets aren't even checked. This sounds pretty typical for university IT. Unfortunately, you will have zero luck getting them to fix the problem because they don't support MACS.
    First of all, your question is pretty important and shouldn't be tucked inside a Verizon FiOS thread where no one will see it. I suggest starting a new question so that people looking for this topic in the future can find the answer.
    I am familiar with this problem. It is an IT configuration problem. I just rolled my own hack for it. I should probably try to improve my hack since obviously other people are experiencing the same problem.
    Before I get started. Why are you even looking? What is the exact problem that you are having? My problem was specific to VPNs but your issue seems even more basic than that. What, exactly, does or does not happen to cause you to search for a fix?
    In the Terminal, run the command "scutil list". How many DNS entries are listed? What are they? You should have one that says "State:/Network/Global/DNS". Type "show State:/Network/Global/DNS". What does it return? Are these the DNS servers that you added?
    Let me know the respones to the above and then I can craft a command that will correct and possibly override those servers properly.

  • DNS lookup failed WRT120N

    Hello,
    I've been having an issue with my internet connection, which has been getting a lot worse over the past 1 month. I purchased the WRT120N about a year and a half ago, and occasionally observed dropped connections, but it was no big deal. Over teh past month or so, however, it seems like I get the "DNS lookup failed" error about every 15-30 minutes. Every time, I have to disconnect and reconnect my computer to my router. In addition, I will be disconnected from XBox Live. This problem may occur every 5 minutes or every few hours.
    I have updated the firmware on the router. I have reset the router, and have reset DNS 1 t0 8.8.8.8 and DNS 2 to 8.8.4.4. THe network is configured as a DHCP. The X-Box has a wired connection, and my laptop experiences this problem whether I use a wired connection or a wireless one.
    I've reached the end of my very limited technology skills, so if anyone has a solution, I'd be more than greatful.
    Thank you!

    To isolate the concern, connect your computer to the modem and observe the connection for a day or a period of time. If the connection is dropping through the modem, contact your ISP. However, if it is stable through the modem, you can adjust the MTU settings of the router. Set the MTU to 1350. Also, reconfigure the wireless settings. Set the channel width to 20 MHz only and select a specific wireless channel. I suggest using 1, 6 or 11.
    Another thing you need to consider is the location of the router. It shouldn’t be too close to your modem as it may create interference. It should be on a higher and open location.

  • Local site blocked - DNS lookup failed

                      Hitting our webpage from the inside is blocked; the policy trace shows Request blocked: Details: DNS Lookup fails
    the local webpage is in the Custom URL Catagory- Allow group...
    This fails when leaving the www off the front.   www.site.com works but site.com fails...
    .site.com and site.com are in the custom URL catagory in an 'allow' group
    this is also in the bypass filter

    A large amount of sites in the world are unable to resolve domains that do not have www in the front. The easiest example is NASA.  Go to nasa.gov and it does not work.  www.nasa.gov does work.  This is due to the admins configuration.  However like chris mentioned I would confirm that your DNS is opperating correctly.
    P.S.  The nasa test might or might not work.  Some browsers automatically change the nasa.gov to www.nasa.gov
    Christian Rahl
    Customer Support Engineer
    Cisco Web Content Security Appliance
    Cisco Technical Assistance Center RTP

  • WSA error DNS lookup failed

    hi,
    When i try to download a file from let say xyz.com i am not able to do so.Policy trace show below result
    User Information
    User Name: r5893
    Group Membership: NBKDOM\r5893, NBKDOM\Limit_Login_Single, NBKDOM\MMS_Access Group, NBKDOM\Screen Saver, NBKDOM\Domain Users, NBKDOM\MMSGroup, NBKDOM\Purchasing&GS-Kuwait, NBKDOM\AllUsers, NBKDOM\Outlook Users, NBKDOM\Administration-Kuwai, NBKDOM\BOUsers, NBKDOM\MYNBKUSERS, NBKDOM\Purchasing Requests - Administration, NBKDOM\EVGROUP001
    User-Agent: Mozilla/5.0 (compatible; MSIE 9.0; Windows NT 6.1; WOW64; Trident/5.0)
    Custom URL Category: Allow sites
    Policy Match
    Cisco IronPort Data Security policy: None
    Decryption policy: None
    Routing policy: Global Routing Policy
    Identity policy: Users
    Access policy: NBK_Users
    Final Result
    Request blocked
    Details: DNS lookup failed
    Trace session complete

    Hi Asim,
    I would investigate the DNS by establishing an SSH session to the M1 interface.  Do an 'nslookup xyz.com' and see if it resolves.  If it does not resolve, you may want to check your DNS server.
    -Vance

  • DNS lookup failed. How to fix with Google chrome?

    "The server at _____.com can't be found, because the DNS lookup failed. This error is often caused by having no connection to the internet or a misconfigured network. It can also be caused by an unresponsive DNS server or a firewall preventing google chrome from accessing the network." 

    Is Safari the same?

  • Post Moved DNS-Lookup-Failed

    Post Moved http://community.bt.com/t5/Other-BB-Queries/DNS-Lookup-Failed/td-p/611636
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

    Is Safari the same?

  • Pcie re-enumerate fail after reset

    In my V7 FPGA image there are several PCIE switch devices and 1 PCIE
    endpoint device. I attach it on a Linux x86 laptop. When the system start
    normally, the hierarchy and the bus:device.function number are :
               SW0(05:00.0)
                |
      |                                       |
     SW1(06:00.0)          SW2(06:01.0)
      |
     EP (08:00.0)
    When I assert a whole chip power on reset. The devices are re-enumerated.
    But the hierarchy may change. Some time they are identically the same with
    the normal ones.But sometime I saw the bus number of SW1/2 has changed and
    the EP failed to be enumerated. The hierarchy is like:
               SW0(05:00.0)
                |
      |                                              |
     SW1(0B:00.0)          SW2(0B:01.0)
      |
     (missing EP,the
    secondary bus number
    of SW1 is 0xD)
    The EP was missing because the HOST didn't send CONIG RD/WR to 0D:00.0
    after it set the secondary bus number of SW1 to be 0xD.
    Can anyone help me to give answer to the following questions:
    1. Why the bus driver/HOST assign 0xB to the secondary bus number to SW0
    rather than 0x6 after reset?
    2. Why the bus driver/HOST didn't send CONIG RD/WR to 0D:00.0 to proceed
    the enumerate?
    BWT: On MS windows system the re-enumerate is always success with
    unchanged hierarchy after reset.

    Hi Anthrol,
    For the BUS:Device, enumeration - if you look at the tree, the 2 switches are on the same tree level, and are this considered on the same "BUS".  If these were Peer-to-Peer capable, they would simply be different devices on the same level.   
    For the re-enumeration, you would need to look into that with the Linux driver controlling the root -- that is responsible for enumeration.  You are correct, if the part never receives a new BDF, it won't appear in the device tree, and anything the Root addresses to BDF 0D:00.0 will be discarded by the switch as URs (Unexpected Requests).  
     

  • My iPod 4G, after reset and iOS 6 install, now has only some album art after syncing music. Even music directly downloaded from iTunes is missing album art. (I'm using iTunes 11.0.1 on Windows Vista)

    My iPod 4G, after a reset and iOS6 install, after I recopied and synced music, is missing most album art. Even songs directly downloaded from iTunes are missing album art. I'm using iTunes 11.0.1 on Windows Vista. My iPod isn't full. Whenever I go to "On This iPod" and add album art and sync, nothing happens. Please help :/

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Unsync all music and resync
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:       
    iOS: How to back up           
    - Restore to factory settings/new iOS device.

Maybe you are looking for