Tcode for checking the Maintenance Plan

Hello,
I want the transaction code for checking the list of maintenance plan for a particular plant. I went thru tcode IP03, IP16 but could not find the option of plant there..
Kindly guide..
Regards,
Naren

Naren,
As stated above, there isn't a plant field in the maintenance plan (only maintenance item, hence the reference ot IP17)
However, it is quite common to use the maintenance plan Sort field as a plant field by customising the table settings for each plant.
PeteA

Similar Messages

  • BAPI for Creation of Maintenance Plan (TCode - IP01)

    Hello
    Kindly help me with the BAPI for Creation of Maintenance Plan (TCode - IP01)
    Thanks and Regards
    Avishek

    Hi
       Check Tcode: IBIP. and LSMW method and below link it may be helpful.
    [link|Re: LSMW for uploading equipment.]
    Thanks,
    Asit Purbey.

  • Tcode for checking that file is on the server

    what is the tcode for checking that file is on the server.
    thanks...

    Hi
    AL11.
    CG3Y/CG3Z.
    Regards,
    Sree

  • My iphone 4s siri is not working, it just worked for a while and stopped. I've checked the data plan and it is intact, i even switched my sim to a friends phone and his siri worked but mine refused even with a wireless network. pls help.

    My iphone 4s siri is not working, it just worked for a while and stopped. I've checked the data plan and it is intact, i even switched my sim to a friends phone and his siri worked but mine refused even with a wireless network. pls help.

    Troubleshooting Siri
    http://support.apple.com/kb/TS4079

  • Tcode to check the event linkage for a terminating event

    Hi ,
    Can some one plzz let me know the transaction code for checking the event linkage for a terminating event
    Thanks
    Sheetal

    And yes the FM RH_GET_TASKS_OF_EVENT gives you the list of tasks for a given BO-terminating event combination. Pass the parameters for this FM as folllows,
    CLSTYP = 'BO'
    CLSNAM = '<BO name>'
    EVENT = '<terminating event name>'
    GET_START_EVENTS = ' '
    GET_TERM_EVENTS = 'X'
    you will get the task list in the table TASKS_OF_EVENTS.
    Thanks,
    Prasath N

  • Display access to be made on the Maintenance Plan.

    Hi Experts
    On the Preventive Maintenance Plan Creation in IP41/ IP42 / IP43 when I enter the Equipment Number all the master data gets copied in the Plan.
    But I am able to change the Planning Plant and also the Planner Group. I would like to have these two fields on the Display mode only. When Equipment number is entered all gets copied automatically and I should not have access to change it in creation of plans.
    Similarly I would also like to make the Tack List mandatory on the maintenance plan.
    I checked in the SPRO but not able to find the node. Should I go for an enhancement ?
    Regards
    Venkat

    Venkat,
    Just a practical issue here.
    What if you create the MP using the equipment data (say PG1), then at some point in the future you change the PG in the equipment to PG2.
    How would you now update the MP with the new PG since the fields would be display-only???
    PeteA

  • T.Code for checking the total value of a material

    Hi Experts,
      Can anybody tel me the T.code for checking the total value of a material which is procured in a specified period?
    Thanks in advance
    Channa

    Refer Tcode ME80FN click on Change Veiw & select Purchase Order History with this you can get PO-GRN-INVOICE Qty & Value details
    Last button on Application tool Bar it is in line of filter, total etc icons
    Also check below reports :
    MC$G - PURCHIS: Material PurchVal Selection
    MC$0 - PURCHIS: PurchGrp PurchVal Selection
    MC$< - PURCHIS: MatGrp PurchVal Selection
    MC$4 - PURCHIS: Vendor PurchVal Selection

  • Get latest order for a scheduled maintenance plan

    Hi experts,
    I have a requirement where i have to get the order id for a scheduled Maintenance plan.My scenario is explained as below:
    A maintenace plan is scheduled and as a result of it an order will be created automatically  by system. Now i have to write a Report program which will be running daily and this report has to pick only those order which are NOT complete and these order will come from the above scheduled maintenance plan.
    Therefore i have to pick incomplete order based on scheduled maintenance plan.Any idea how to achieve this requirement?
    In case of any doubt please let me know.
    Regards,
    Abhishek

    Thanks for reply. But my requirement is a bit differen.
    I need a BAPI which can take Maintenance Plan as input and it can return the latest created incomplete order which is created due to scheduling of Maintenance Plan.
    Regards,
    Abhishek

  • Settings for performance based maintenance plan

    Hi experts,
    Incase of hour or Km dependent performance base plan, how we can fix the reading (In hours or Km) limit or period of order generation? what is the impact of annual estimate? Please give me an example with all readings.
    Regards,

    When you create a plan with a counter (Associate a measurement point of counter type to the same), then you would be able to specify at what intervals (Counter readings for this measurement point), the call object associated to the Maintenance plan should be generated.
    The actual call date for this maintenance plan however depends on the "Annual estimate " for the measurement point counter and also the actual counter readings captured for the measurement point
    For ex: Annual estimate maintained for the Point : 12,000 Miles .Maintenance for this equipment should be triggered for every 1000 Miles (This should be the counter interval maintained for the Maintenance plan). Based on the above the maintenance plan would generated a call every one month (Annual estimate / period).As an example,  when this Maintenance plan is scheduled for 1 yr, then 12 maintenance calls will be generated one each for every month. The actual and scheduled dates for the call depends on the various other scheduling parameters maintained for the Plan.
    Its critical for any counter based maintenance plan that the counter reading is Captured , Through measurement documents regularly, EVEN IF THERE IS NO CHANGE TO THE COUNTER READING, Otherwise, the system generates call objects (for example, maintenance orders) based on the estimated annual performance entered for the counter, even though the counter reading has not in reality been reached.
    for ex: owing to a vehicle breakdown/ repair if the vehicle has been in repair shop for a month,To avoid a maintenance order being created before it is needed, you maintain the new total counter reading in the system regularly over the period of the month. You then reschedule the maintenance plan using IP30, and the call date is recalculated based on the updated counter reading. In this case, the call date would be later.
    [Detailed SAP Help|http://help.sap.com/erp2005_ehp_04/helpdata/en/3c/abbcf6413911d1893d0000e8323c4f/frameset.htm].
    Regards
    Narasimhan

  • User exit or a badi for checking the vendor email id in me22n on me29n

    hi all,
    can anybody suggest me a user exit or a badi  for checking the email id of the vendor in me21n or me22n or me29n.
    i.e. a user exit or a BADI which gets hit either at the time of creation or release of a purchase order.
    plz suggest me a solution its urgent.
    regards,
    santosh

    Hi Santosh,
    Have you looked BADI <b>ME_PROCESS_PO_CUST</b> or user exits <b>EXIT_SAPMM06E_016</b> / <b>EXIT_SAPMM06E_017</b>?
    Hope this will help.
    Regards,
    Ferry Lianto
    Please reward points if helpful.

  • Visio 2010 Validation for Checking the number of a specific type of shape.

    I have written a rule for flowchart for checking the number of Start/End Shapes in a document.
    The FilterExpression is as follows:
    AGGCOUNT(FILTERSET(SHAPESONPAGE(), HASCATEGORY("Start/End"))) > 0
    The TestExpression is as follows:
    AGGCOUNT(FILTERSET(SHAPESONPAGE(),HASCATEGORY("Start/End"))) = 2
    (Since totally there are 2 shapes: 1 Start and 1 End Shape)
    However, it is not working. Can anybody tell me what is wrong in the expressions.

    Well, it worked for me, so I want to check that you modified the Start/End master to have the User.msvShapeCategories row with the value "Start/End", as I did?
    A Category is not a Master
    David J Parker MVP (Visio) http://blog.bvisual.net

  • Kindly let me know the transaction for checking the Status of par.User?

    Kindly let me know the transaction for checking the Particular Users Status?
    I mean to say,Which Transaction is he into?
    Or Is he/She Logged on to a particular System?
    Regards,
    Shashank.

    Hi,
    Go to Transaction SM04.You will find the List of Users And the List of transactions ther are currently using.
    Regards,
    Sujit

  • Standard function module for checking the sales organization and plant

    Hi all,
        Does have standard function module for checking the relationship between sales organization and plant?
    Thanks a lot!
    Nina

    hi
    good
    check these BAPIS
    BAPI_SALESGROUP_GET_DETAIL     Sales Group: Display Name                                                
    BAPI_SALESOFFICE_GET_DETAIL    Sales Office: Display Name                                               
    BAPI_SALESOFFICE_GRP_EXIST     Sales Office / Sales Group: Existence Check                              
    BAPI_SALESORG_EXIST            Sales Organization: Existence Check                                      
    BAPI_SALESORG_GET_DETAIL       Sales Organization: Display Data                                         
    BAPI_SALESORG_OFFICE_EXIST     Sales Organization / Sales Office: Existence Check                       
    PLANT=>
    BAPI_PROMO_GETSITEPLANNING     Detailed Data for the Plants Involved in a Promotion   
    thanks
    mrutyun^

  • What is the tracking ID for checking the status of a sent text message??

    i don't know what the tracking ID is for checking the status of a sent text message...

    You didn't need to post here and start a new thread; you could have just done a search, i.e.,
    https://community.verizonwireless.com/thread/455106

  • Table for checking the appended fields in the standard extractor

    Hello,
    Please let me know the table name for checking the appended fields in the standard extractor.
    Thanks in advance

    Hello,
    From Rsa6 , goto your extractor from there you may get the name of your strucutre
    Go to DD03L and enter this name
    And you get to see all the fields there..
    waiting for your feedback.
    Regards
    Nitin Bhatia

Maybe you are looking for