Tcp ports during update

Hi guys,
which tcp ports normally Ironport WSA uses to communicate for update or during normal operations ?
Customer where we are installing 2 S160 ,send me this alert log from existing Checkpoint IPS , where src is ironport (10.0.1.5) dst is ip address (10.0.0.97) of Windows AD, DNS and NTP server .
8Oct2011 7:36:47 drop 80.207.58.46 >eth2 mail product: SmartDefense; TCP flags: FIN; Attack Info: TCP flags do not make sense; attack: Bad packet; src: 10.0.1.5; s_port: 7745; dst: 10.0.0.97; service: ldap; proto: tcp;
This log is generated every 15 min, so i believe that is something related to update, but service type ldap give me some doubt.
May be wsa check AD every 15 min ?
Thanks
Best regards
Luca

Luca,
I'm pretty sure that's a "health" check on the LDAP connection to your domain controller. If that fails, the WSA could alert you that it can't get to the domain controller to auth users...
If your box is joined to the domain, it could be related to the the secure channel too..
Ken

Similar Messages

Iphone 4S block during update 6.1.3 and iTunes doesn't recognize my phone

Hi. During update on iphone 4S, I had an error message from itunes. It said that update wasn't possible. And now Iphone block on the screen to connect to iTunes. But iTunes doesn't recognize iPhone. If I try to reinstall the last version, I have the message that it is impossible because the current version is newer!....
Can somebody help me please?

Error 2, 4 (or -4), 6, 1000, 9006
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. Your default packet size being set incorrectly can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or photos.apple.com is not blocked by a firewall, or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under Advanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.

Pre-Requisite Check SQL Server 2012 SP2 TCP Port Enabled Error

When doing the pre-requisite check to install SCCM (CAS) using an instance of SQL Server 2012 SP2, you get the following error even though SQL Server TCP port has been enabled, set to static port 4022 on the IP addresses in use in SQL Server Configuration
Manager under Protocols for <SQLInstanceName>: configuration manager primary site and central administration site require sql server tcp enables and set to static port
To resolve this issue, make sure "4022" is also set in the IPAll node in SQL Server Configuration Manager under Protocols for <SQLInstanceName> then restart the SQL Service and re-run the pre-requisite check and you should be good to go.
To avoid SCCM SQL-related install failure, keep in mind that SCCM SQL Service Broker (SSB) (used to replicate data between database sites) is set to port 4022 by default. This is different from and cannot be same as the tcp static port set in SQL Server
Configuration Manager under Protocols for <SQLInstanceName>. For example SSB can use its default tcp port 4022 while a static tcp port of 4023 can be set in SQL Server Configuration Manager under Protocols for <SQLInstanceName> or vice-versa. The
SCCM SSB port number can be adjusted during SCCM installation on the Database Information page. My take it so change SSB port to 4023 and leave SQL default port at 4022 since SQL serves potentially many apps while SSB is used within/by SCCM.
If you are getting errors relating to SQL Server service running accounts, SQL Server Collation, and/or SQL Server sysadmin rights while attempting to install a primary site, unselect the SCCM installation option to install default settings at the beginning
of the install process.
Also, ensure to install important updates and restart the server.

Thank you for sharing.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

TS3694 iPhone 5.....during update to iOS 7 I have lost the power supply (blackout)

this issue , happen to my iPhone 5.....during update to iOS 7 I have lost the power supply (blackout)
Sudden screen : USB pointing to iTunes . it shows that it need a restore and update .. after downloading the software
and extracting .. found Error1 at the point Verify firmware . AGAIN AND
and this is the log ..
2014-08-11 15:46:30.611 [4472:1648]: restore library built Feb 12 2014 at 16:27:17
2014-08-11 15:46:30.611 [4472:1648]: iTunes: iTunes 11.3.1.2
2014-08-11 15:46:30.611 [4472:1648]: iTunes: Software payload version: 11D257 (option key)
2014-08-11 15:46:30.611 [4472:1648]: iTunes: Using MobileRestore state machine
[13:47:25.0555] Changing state from 'Idle' to 'Restoring'
[13:47:25.0555] device software does not support nonce generation
[13:47:25.0555] requested restore behavior: Erase
[13:47:25.0570] requested variant: Erase
[13:47:25.0570] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBSS" Digest = "<CFData 061FEA80 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "LLB" Digest = "<CFData 061FD2E0 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[13:47:26.0553] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[13:47:26.0569] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[13:47:26.0569] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[13:47:26.0569] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[13:47:26.0569] amai: _AMAuthInstallBundleCreateServerRequestDictionary: using UniqueBuildID <CFData 0BA32F38 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[13:47:26.0569] amai: AMAuthInstallRequestSendSync: SSO function returned NULL, SSO disabled.
[13:47:26.0569] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/C:/Users/Dell/AppData/Local/Temp/Per2046.tmp/amai/debug/tss-re quest.plist
[13:47:27.0068] amai: tss_submit_job: HttpQueryInfo returned 200
[13:47:27.0286] amai: AMAuthInstallRequestSendSync: received tss response (server version: 2.1.0)
[13:47:27.0286] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/C:/Users/Dell/AppData/Local/Temp/Per2046.tmp/amai/debug/tss-re sponse.plist
[13:47:27.0318] amai: _AMAuthInstallBundlePopulatePersonalizedBundle: no entry in manifest found for "Diags"
[13:47:27.0333] <DFU Device 0562C260>: production fused device
[13:47:27.0333] requested restore behavior: Erase
[13:47:27.0333] device software does not support nonce generation
[13:47:27.0349] WinDFU::OpenDFUDevice: path: \\?\USB#VID_05AC&PID_1227#{B8085869-FEB9-404B-8CB1-1E5C14FA8C54}\0000#93126bb7
[13:47:27.0349] WinDFU::OpenDeviceByPath: \\?\USB#VID_05AC&PID_1227#{B8085869-FEB9-404B-8CB1-1E5C14FA8C54}\0000#93126bb7
[13:47:27.0364] <DFU Device 0562C260>: operation 0 progress 2
[13:47:27.0380] <DFU Device 0562C260>: operation 0 progress 5
[13:47:27.0396] <DFU Device 0562C260>: operation 0 progress 8
[13:47:27.0411] <DFU Device 0562C260>: operation 0 progress 10
[13:47:27.0427] <DFU Device 0562C260>: operation 0 progress 13
[13:47:27.0442] <DFU Device 0562C260>: operation 0 progress 16
[13:47:27.0458] <DFU Device 0562C260>: operation 0 progress 18
[13:47:27.0474] <DFU Device 0562C260>: operation 0 progress 21
[13:47:27.0489] <DFU Device 0562C260>: operation 0 progress 24
[13:47:27.0505] <DFU Device 0562C260>: operation 0 progress 26
[13:47:27.0520] <DFU Device 0562C260>: operation 0 progress 29
[13:47:27.0536] <DFU Device 0562C260>: operation 0 progress 32
[13:47:27.0552] <DFU Device 0562C260>: operation 0 progress 34
[13:47:27.0567] <DFU Device 0562C260>: operation 0 progress 37
[13:47:27.0583] <DFU Device 0562C260>: operation 0 progress 40
[13:47:27.0598] <DFU Device 0562C260>: operation 0 progress 42
[13:47:27.0614] <DFU Device 0562C260>: operation 0 progress 45
[13:47:27.0630] <DFU Device 0562C260>: operation 0 progress 48
[13:47:27.0645] <DFU Device 0562C260>: operation 0 progress 50
[13:47:27.0661] <DFU Device 0562C260>: operation 0 progress 53
[13:47:27.0676] <DFU Device 0562C260>: operation 0 progress 56
[13:47:27.0692] <DFU Device 0562C260>: operation 0 progress 59
[13:47:27.0708] <DFU Device 0562C260>: operation 0 progress 61
[13:47:27.0723] <DFU Device 0562C260>: operation 0 progress 64
[13:47:27.0739] <DFU Device 0562C260>: operation 0 progress 67
[13:47:27.0754] <DFU Device 0562C260>: operation 0 progress 69
[13:47:27.0770] <DFU Device 0562C260>: operation 0 progress 72
[13:47:27.0786] <DFU Device 0562C260>: operation 0 progress 75
[13:47:27.0801] <DFU Device 0562C260>: operation 0 progress 77
[13:47:27.0817] <DFU Device 0562C260>: operation 0 progress 80
[13:47:27.0832] <DFU Device 0562C260>: operation 0 progress 83
[13:47:27.0848] <DFU Device 0562C260>: operation 0 progress 85
[13:47:27.0864] <DFU Device 0562C260>: operation 0 progress 88
[13:47:27.0879] <DFU Device 0562C260>: operation 0 progress 91
[13:47:27.0895] <DFU Device 0562C260>: operation 0 progress 93
[13:47:27.0910] <DFU Device 0562C260>: operation 0 progress 96
[13:47:27.0926] <DFU Device 0562C260>: operation 0 progress 99
[13:47:27.0926] WinDFU::UploadData: EOF, cbRead: 554
[13:47:27.0942] <DFU Device 0562C260>: operation 0 progress 100
[13:47:27.0942] WinDFU::UploadData: ZLP
[13:47:27.0957] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 6
[13:47:27.0957] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST_SYNC
[13:47:27.0957] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 7
[13:47:27.0957] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST, PollTimeout: 3000
[13:47:30.0968] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 8
[13:47:30.0968] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST_WAIT_RESET
[13:47:30.0968] WinDFU::ResetDevice: resetting...
[13:47:31.0046] WinDFU::FinalizeDfuUpdate: success
[13:47:31.0046] <DFU Device 0562C260>: DFU succeeded
[13:47:31.0046] Finished DFU Restore Phase: Successful
[13:47:31.0218] DFU mode device disconnected
[13:47:31.0218] Device removed when in state Restoring, moving device to transition state
[13:47:31.0218] Changing state from 'Restoring' to 'Transitioning'
[13:47:31.0218] Creating timer to monitor transition
[13:47:32.0175] DFU mode device connected
[13:47:32.0175] Transitioning device returned, continuing restore.
[13:47:32.0175] Canceling timer
[13:47:32.0175] Changing state from 'Transitioning' to 'Restoring'
[13:47:32.0175] AppleDevice::GetDeviceID: failed for iBoot
[13:47:32.0175] requested restore behavior: Erase
[13:47:32.0175] requested variant: Erase
[13:47:32.0175] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:33.0033] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is True
[13:47:33.0033] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreLogo" Digest = "<CFData 061FDC70 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0033] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreDeviceTree" Digest = "<CFData 061FE378 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0033] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreKernelCache" Digest = "<CFData 0B9D5148 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0033] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreRamDisk" Digest = "<CFData 0B9D5190 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBEC" Digest = "<CFData 0B9D51D8 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBSS" Digest = "<CFData 0B9D5220 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "KernelCache" Digest = "<CFData 0B9D5268 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow1" Digest = "<CFData 0B9D52B0 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow0" Digest = "<CFData 0B9D52F8 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "LLB" Digest = "<CFData 0B9D5340 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBoot" Digest = "<CFData 0B9D5388 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "DeviceTree" Digest = "<CFData 0B9D53D0 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging1" Digest = "<CFData 0B9D5418 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "AppleLogo" Digest = "<CFData 0B9D5460 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryPlugin" Digest = "<CFData 0B9D54A8 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryFull" Digest = "<CFData 06266350 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging0" Digest = "<CFData 06266398 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RecoveryMode" Digest = "<CFData 062663E0 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[13:47:33.0049] amai: _AMAuthInstallBundleCreateServerRequestDictionary: using UniqueBuildID <CFData 064698C8 [7161907C]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[13:47:33.0064] amai: AMAuthInstallRequestSendSync: SSO function returned NULL, SSO disabled.
[13:47:33.0064] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/C:/Users/Dell/AppData/Local/Temp/Per2046.tmp/amai/debug/tss-re quest.plist
[13:47:33.0298] amai: tss_submit_job: HttpQueryInfo returned 200
[13:47:33.0501] amai: AMAuthInstallRequestSendSync: received tss response (server version: 2.1.0)
[13:47:33.0501] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/C:/Users/Dell/AppData/Local/Temp/Per2046.tmp/amai/debug/tss-re sponse.plist
[13:47:33.0501] amai: _AMAuthInstallBundleInstallPersonalizedEntry: entry "iBSS" has been previously personalized; skipping it
[13:47:33.0501] amai: _AMAuthInstallBundleInstallPersonalizedEntry: entry "LLB" has been previously personalized; skipping it
[13:47:33.0517] amai: _AMAuthInstallBundlePopulatePersonalizedBundle: no entry in manifest found for "Diags"
[13:47:33.0532] <DFU Device 0BA2A9D8>: production fused device
[13:47:33.0532] requested restore behavior: Erase
[13:47:33.0532] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:33.0532] AppleDevice::GetDeviceID: failed for iBoot
[13:47:33.0532] WinDFU::OpenDFUDevice: path: \\?\USB#VID_05AC&PID_1227#{B8085869-FEB9-404B-8CB1-1E5C14FA8C54}\0000#ca28221e
[13:47:33.0532] WinDFU::OpenDeviceByPath: \\?\USB#VID_05AC&PID_1227#{B8085869-FEB9-404B-8CB1-1E5C14FA8C54}\0000#ca28221e
[13:47:33.0564] <DFU Device 0BA2A9D8>: operation 0 progress 0
[13:47:33.0579] <DFU Device 0BA2A9D8>: operation 0 progress 1
[13:47:33.0595] <DFU Device 0BA2A9D8>: operation 0 progress 2
[13:47:33.0626] <DFU Device 0BA2A9D8>: operation 0 progress 3
[13:47:33.0642] <DFU Device 0BA2A9D8>: operation 0 progress 4
[13:47:33.0657] <DFU Device 0BA2A9D8>: operation 0 progress 5
[13:47:33.0688] <DFU Device 0BA2A9D8>: operation 0 progress 6
[13:47:33.0704] <DFU Device 0BA2A9D8>: operation 0 progress 7
[13:47:33.0735] <DFU Device 0BA2A9D8>: operation 0 progress 8
[13:47:33.0751] <DFU Device 0BA2A9D8>: operation 0 progress 9
[13:47:33.0766] <DFU Device 0BA2A9D8>: operation 0 progress 10
[13:47:33.0798] <DFU Device 0BA2A9D8>: operation 0 progress 11
[13:47:33.0813] <DFU Device 0BA2A9D8>: operation 0 progress 12
[13:47:33.0844] <DFU Device 0BA2A9D8>: operation 0 progress 13
[13:47:33.0860] <DFU Device 0BA2A9D8>: operation 0 progress 14
[13:47:33.0876] <DFU Device 0BA2A9D8>: operation 0 progress 15
[13:47:33.0907] <DFU Device 0BA2A9D8>: operation 0 progress 16
[13:47:33.0922] <DFU Device 0BA2A9D8>: operation 0 progress 17
[13:47:33.0954] <DFU Device 0BA2A9D8>: operation 0 progress 18
[13:47:33.0969] <DFU Device 0BA2A9D8>: operation 0 progress 19
[13:47:33.0985] <DFU Device 0BA2A9D8>: operation 0 progress 20
[13:47:34.0016] <DFU Device 0BA2A9D8>: operation 0 progress 21
[13:47:34.0032] <DFU Device 0BA2A9D8>: operation 0 progress 22
[13:47:34.0063] <DFU Device 0BA2A9D8>: operation 0 progress 23
[13:47:34.0078] <DFU Device 0BA2A9D8>: operation 0 progress 24
[13:47:34.0094] <DFU Device 0BA2A9D8>: operation 0 progress 25
[13:47:34.0125] <DFU Device 0BA2A9D8>: operation 0 progress 26
[13:47:34.0141] <DFU Device 0BA2A9D8>: operation 0 progress 27
[13:47:34.0172] <DFU Device 0BA2A9D8>: operation 0 progress 28
[13:47:34.0188] <DFU Device 0BA2A9D8>: operation 0 progress 29
[13:47:34.0203] <DFU Device 0BA2A9D8>: operation 0 progress 30
[13:47:34.0234] <DFU Device 0BA2A9D8>: operation 0 progress 31
[13:47:34.0250] <DFU Device 0BA2A9D8>: operation 0 progress 32
[13:47:34.0281] <DFU Device 0BA2A9D8>: operation 0 progress 33
[13:47:34.0297] <DFU Device 0BA2A9D8>: operation 0 progress 34
[13:47:34.0312] <DFU Device 0BA2A9D8>: operation 0 progress 35
[13:47:34.0344] <DFU Device 0BA2A9D8>: operation 0 progress 36
[13:47:34.0359] <DFU Device 0BA2A9D8>: operation 0 progress 37
[13:47:34.0390] <DFU Device 0BA2A9D8>: operation 0 progress 38
[13:47:34.0406] <DFU Device 0BA2A9D8>: operation 0 progress 39
[13:47:34.0422] <DFU Device 0BA2A9D8>: operation 0 progress 40
[13:47:34.0453] <DFU Device 0BA2A9D8>: operation 0 progress 41
[13:47:34.0468] <DFU Device 0BA2A9D8>: operation 0 progress 42
[13:47:34.0500] <DFU Device 0BA2A9D8>: operation 0 progress 43
[13:47:34.0515] <DFU Device 0BA2A9D8>: operation 0 progress 44
[13:47:34.0531] <DFU Device 0BA2A9D8>: operation 0 progress 45
[13:47:34.0562] <DFU Device 0BA2A9D8>: operation 0 progress 46
[13:47:34.0578] <DFU Device 0BA2A9D8>: operation 0 progress 47
[13:47:34.0593] <DFU Device 0BA2A9D8>: operation 0 progress 48
[13:47:34.0624] <DFU Device 0BA2A9D8>: operation 0 progress 49
[13:47:34.0640] <DFU Device 0BA2A9D8>: operation 0 progress 50
[13:47:34.0671] <DFU Device 0BA2A9D8>: operation 0 progress 51
[13:47:34.0687] <DFU Device 0BA2A9D8>: operation 0 progress 52
[13:47:34.0702] <DFU Device 0BA2A9D8>: operation 0 progress 53
[13:47:34.0734] <DFU Device 0BA2A9D8>: operation 0 progress 54
[13:47:34.0749] <DFU Device 0BA2A9D8>: operation 0 progress 55
[13:47:34.0780] <DFU Device 0BA2A9D8>: operation 0 progress 56
[13:47:34.0796] <DFU Device 0BA2A9D8>: operation 0 progress 57
[13:47:34.0812] <DFU Device 0BA2A9D8>: operation 0 progress 58
[13:47:34.0843] <DFU Device 0BA2A9D8>: operation 0 progress 59
[13:47:34.0858] <DFU Device 0BA2A9D8>: operation 0 progress 60
[13:47:34.0890] <DFU Device 0BA2A9D8>: operation 0 progress 61
[13:47:34.0905] <DFU Device 0BA2A9D8>: operation 0 progress 62
[13:47:34.0921] <DFU Device 0BA2A9D8>: operation 0 progress 63
[13:47:34.0952] <DFU Device 0BA2A9D8>: operation 0 progress 64
[13:47:34.0968] <DFU Device 0BA2A9D8>: operation 0 progress 65
[13:47:34.0999] <DFU Device 0BA2A9D8>: operation 0 progress 66
[13:47:35.0014] <DFU Device 0BA2A9D8>: operation 0 progress 67
[13:47:35.0030] <DFU Device 0BA2A9D8>: operation 0 progress 68
[13:47:35.0061] <DFU Device 0BA2A9D8>: operation 0 progress 69
[13:47:35.0077] <DFU Device 0BA2A9D8>: operation 0 progress 70
[13:47:35.0108] <DFU Device 0BA2A9D8>: operation 0 progress 71
[13:47:35.0124] <DFU Device 0BA2A9D8>: operation 0 progress 72
[13:47:35.0139] <DFU Device 0BA2A9D8>: operation 0 progress 73
[13:47:35.0170] <DFU Device 0BA2A9D8>: operation 0 progress 74
[13:47:35.0186] <DFU Device 0BA2A9D8>: operation 0 progress 75
[13:47:35.0217] <DFU Device 0BA2A9D8>: operation 0 progress 76
[13:47:35.0233] <DFU Device 0BA2A9D8>: operation 0 progress 77
[13:47:35.0248] <DFU Device 0BA2A9D8>: operation 0 progress 78
[13:47:35.0280] <DFU Device 0BA2A9D8>: operation 0 progress 79
[13:47:35.0295] <DFU Device 0BA2A9D8>: operation 0 progress 80
[13:47:35.0326] <DFU Device 0BA2A9D8>: operation 0 progress 81
[13:47:35.0342] <DFU Device 0BA2A9D8>: operation 0 progress 82
[13:47:35.0358] <DFU Device 0BA2A9D8>: operation 0 progress 83
[13:47:35.0389] <DFU Device 0BA2A9D8>: operation 0 progress 84
[13:47:35.0404] <DFU Device 0BA2A9D8>: operation 0 progress 85
[13:47:35.0436] <DFU Device 0BA2A9D8>: operation 0 progress 86
[13:47:35.0451] <DFU Device 0BA2A9D8>: operation 0 progress 87
[13:47:35.0467] <DFU Device 0BA2A9D8>: operation 0 progress 88
[13:47:35.0498] <DFU Device 0BA2A9D8>: operation 0 progress 89
[13:47:35.0514] <DFU Device 0BA2A9D8>: operation 0 progress 90
[13:47:35.0529] <DFU Device 0BA2A9D8>: operation 0 progress 91
[13:47:35.0560] <DFU Device 0BA2A9D8>: operation 0 progress 92
[13:47:35.0576] <DFU Device 0BA2A9D8>: operation 0 progress 93
[13:47:35.0607] <DFU Device 0BA2A9D8>: operation 0 progress 94
[13:47:35.0623] <DFU Device 0BA2A9D8>: operation 0 progress 95
[13:47:35.0638] <DFU Device 0BA2A9D8>: operation 0 progress 96
[13:47:35.0670] <DFU Device 0BA2A9D8>: operation 0 progress 97
[13:47:35.0685] <DFU Device 0BA2A9D8>: operation 0 progress 98
[13:47:35.0716] <DFU Device 0BA2A9D8>: operation 0 progress 99
[13:47:35.0716] WinDFU::UploadData: EOF, cbRead: 1116
[13:47:35.0732] <DFU Device 0BA2A9D8>: operation 0 progress 100
[13:47:35.0732] WinDFU::UploadData: ZLP
[13:47:35.0748] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 6
[13:47:35.0748] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST_SYNC
[13:47:35.0748] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 7
[13:47:35.0748] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST, PollTimeout: 3000
[13:47:38.0758] WinDFU::FinalizeDfuUpdate: GetStatus: status: 0, state: 8
[13:47:38.0758] WinDFU::ProcessUpdateState: status.bState == DFU_STATE_MANIFEST_WAIT_RESET
[13:47:38.0758] WinDFU::ResetDevice: resetting...
[13:47:38.0836] WinDFU::FinalizeDfuUpdate: success
[13:47:38.0836] <DFU Device 0BA2A9D8>: DFU succeeded
[13:47:38.0836] Finished DFU Restore Phase: Successful
[13:47:39.0039] DFU mode device disconnected
[13:47:39.0039] Device removed when in state Restoring, moving device to transition state
[13:47:39.0039] Changing state from 'Restoring' to 'Transitioning'
[13:47:39.0039] Creating timer to monitor transition
[13:47:41.0674] Recovery mode device connected
[13:47:41.0674] Transitioning device returned, continuing restore.
[13:47:41.0674] Canceling timer
[13:47:41.0674] Changing state from 'Transitioning' to 'Restoring'
[13:47:41.0684] requested restore behavior: Erase
[13:47:41.0684] requested variant: Erase
[13:47:41.0684] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[13:47:42.0512] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "iBSS" has been previously personalized; skipping it
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "LLB" has been previously personalized; skipping it
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[13:47:42.0528] amai: _AMAuthInstallBundleCreateServerRequestDictionary: nothing to be done
[13:47:42.0528] iBoot build-version = iBoot-1940.10.58
[13:47:42.0528] iBoot build-style = RELEASE
[13:47:42.0528] requested restore behavior: Erase
[13:47:42.0528] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0528] requested restore behavior: Erase
[13:47:42.0528] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0543] unable to open device_map.txt: No such file or directory
[13:47:42.0543] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[13:47:42.0543] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[13:47:42.0543] AMDeviceIoControl: GetOverlappedResult failed
[13:47:42.0543] AMDeviceIoControl: pipe stall
[13:47:42.0543] USBControlTransfer: error 31, usbd status c0000004
[13:47:42.0543] command device request for 'getenv radio-error' failed: 2008
[13:47:42.0543] radio-error not set
[13:47:42.0543] unable to open device_map.txt: No such file or directory
[13:47:42.0543] <Recovery Mode Device 0555AEB8>: production fused device
[13:47:42.0543] requested restore behavior: Erase
[13:47:42.0543] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0543] requested restore behavior: Erase
[13:47:42.0543] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0543] interface has 1 endpoints, file pipe = 1
[13:47:42.0543]
[13:47:42.0543] <Recovery Mode Device 0555AEB8>: operation 4 progress -1
[13:47:42.0606] unable to open device_map.txt: No such file or directory
[13:47:42.0606] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[13:47:42.0606] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[13:47:42.0606] requested restore behavior: Erase
[13:47:42.0606] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0606] requested restore behavior: Erase
[13:47:42.0606] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:42.0606] <Recovery Mode Device 0555AEB8>: operation 42 progress -1
[13:47:42.0606] requested restore behavior: Erase
[13:47:42.0621] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:43.0651] <Recovery Mode Device 0555AEB8>: operation 5 progress -1
[13:47:43.0994] unable to open device_map.txt: No such file or directory
[13:47:43.0994] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[13:47:43.0994] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[13:47:43.0994] AMDeviceIoControl: GetOverlappedResult failed
[13:47:43.0994] AMDeviceIoControl: pipe stall
[13:47:43.0994] USBControlTransfer: error 31, usbd status c0000004
[13:47:43.0994] command device request for 'getenv ramdisk-delay' failed: 2008
[13:47:45.0616] <Recovery Mode Device 0555AEB8>: operation 6 progress -1
[13:47:46.0630] <Recovery Mode Device 0555AEB8>: operation 7 progress -1
[13:47:46.0942] <Recovery Mode Device 0555AEB8>: operation 8 progress -1
[13:47:46.0958] unable to open device_map.txt: No such file or directory
[13:47:46.0958] found device map entry for 0x00008950 0x00000002. boardConfig=n42ap platform=s5l8950x
[13:47:46.0958] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[13:47:46.0958] <Recovery Mode Device 0555AEB8>: operation 9 progress -1
[13:47:46.0958] <Recovery Mode Device 0555AEB8>: Recovery mode succeeded
[13:47:46.0958] Finished Recovery Restore Phase: Successful
[13:47:48.0409] Recovery mode device disconnected
[13:47:48.0409] Device removed when in state Restoring, moving device to transition state
[13:47:48.0409] Changing state from 'Restoring' to 'Transitioning'
[13:47:48.0409] Creating timer to monitor transition
[13:47:52.0895] RestoreOS mode device connected
[13:47:52.0895] Transitioning device returned, continuing restore.
[13:47:52.0905] Canceling timer
[13:47:52.0905] Changing state from 'Transitioning' to 'Restoring'
[13:47:52.0905] <Restore Device 05577800>: operation 44 progress -1
[13:47:52.0905] requested restore behavior: Erase
[13:47:52.0905] requested variant: Erase
[13:47:52.0905] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "iBSS" has been previously personalized; skipping it
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[13:47:53.0777] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "LLB" has been previously personalized; skipping it
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[13:47:53.0792] amai: _AMAuthInstallBundleCreateServerRequestDictionary: nothing to be done
[13:47:53.0792] requested restore behavior: Erase
[13:47:53.0792] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:53.0792] device did not return saved USB log
[13:47:53.0792] device did not return saved panic log
[13:47:53.0792] previous restore failed with exit status 0x100
[13:47:53.0792] connected to service com.apple.mobile.restored
[13:47:53.0808] using protocol version 13
[13:47:53.0808] unable to open device_map.txt: No such file or directory
[13:47:53.0808] board config = n42ap
[13:47:53.0808] no value returned for BootArgs
[13:47:53.0824] _copyDeviceProperty() failed for restore bootargs
[13:47:53.0824] no value returned for MarketingPartNumber
[13:47:53.0824] _copyDeviceProperty() failed for mpn
[13:47:53.0824] requested restore behavior: Erase
[13:47:53.0824] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[13:47:53.0839] value query for 'HardwareModel' returned 'N42AP'
[13:47:53.0839] <Restore Device 05577800>: operation 28 progress -1
[13:48:10.0360] previous restore failed: re:INF@ 145] created partition 1 as 'Effaceable'
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 2 as 'NVRAM'
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 3 as 'Firmware'
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 4 as 'Filesystem'
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 4
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 5 as 'System Config'
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 6 as 'Diagnostic Data'
[13:48:10.0360] [nand_part_core:INF@ 145] created partition 7 as 'Bad Block Table'
[13:48:10.0360] com.apple.AppleFSCompressionTypeZlib load succeeded
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 7
[13:48:10.0360] AppleSamsungSerial: Identified Serial Port on ARM Device=uart1 at 0x32600000(0x82cc6000)
[13:48:10.0360] L2TP domain init
[13:48:10.0360] L2TP domain init complete
[13:48:10.0360] PPTP domain init
[13:48:10.0360] AppleSwissPPNFTL started with IOFlashStoragePartition provider
[13:48:10.0360] [NAND] _FindFlashMediaAndKeepout:601 physical nand block offset 1
[13:48:10.0360] AppleNANDFTL registered[NAND] start:356 this 0x85e41800 PROVIDER=0x85f2a400 flashMedia=0x85f2a400
[13:48:10.0360] [NAND] WMR_Start:149 Apple PPN NAND Driver, Read/Write
[13:48:10.0360] [NAND] WMR_Start:174 FIL_Init [OK]
[13:48:10.0360] AppleSamsungSerial: Identified Serial Port on ARM Device=uart3 at 0x32800000(0xde3b4000)
[13:48:10.0360] virtual bool AppleDisplayPipe::start_hardware(IOService *), auto-detect chip
[13:48:10.0360] [NAND] WMR_Open:371 VFL_Open    [OK]
[13:48:10.0360] Scaler 0 enableDeviceClock(true,HALF_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 0 enableDeviceClock(true,FULL_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 0 enableDevicePower(true,0,HALF_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 0 enableDeviceClock(false,FULL_CLOCK_INDEX) = 0x0
[13:48:10.0360] void AppleDisplayPipe::setupVideoDownscalingLimits(): minimum-frequency property not found, using getClockFrequency(0) instead.
[13:48:10.0360] Scaler 1 enableDeviceClock(true,HALF_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 1 enableDeviceClock(true,FULL_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 1 enableDevicePower(true,0,HALF_CLOCK_INDEX) = 0x0
[13:48:10.0360] Scaler 1 enableDeviceClock(false,FULL_CLOCK_INDEX) = 0x0
[13:48:10.0360] AppleMultitouchN1SPI: successfully started
[13:48:10.0360] AppleH4CamIn::start - back camera expected
[13:48:10.0360] AppleH4CamIn::start - front camera expected
[13:48:10.0360] AppleH4CamIn::power_off_hardware
[13:48:10.0360] AppleAP3DSH::probe found device with ID: 0x3f
[13:48:10.0360] AppleAP3DSH::handleStart _calibrationMatrix [64699 -1892 -370] [-1570 65035 -244] [849 465 63854]
[13:48:10.0360] AppleAP3DSH::handleStart _calibrationOffsets [518853 -714699 -1661621]
[13:48:10.0360] AppleAP3DSH::handleStart - No calibration inverse matrix or the data is invalid, Compute locally
[13:48:10.0360] AppleAP3DSH::handleStart _calibrationInverseMatrix [66427 1929 393] [1599 66087 261] [-895 -507 67257]
[13:48:10.0360] AppleAP3DSH::handleStart _odr400HzSampleInterval = 2440
[13:48:10.0360] AppleH4CamIn::setPowerStateGated: 0
[13:48:10.0360] AppleCS35L19Amp: could not allocate control 395
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableDetect 1
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableType USBHost
[13:48:10.0360] AppleSynopsysOTGDevice::gated_handleUSBCableConnect cable connected, but don't have device configuration yet
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableDetect 0
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableType Detached
[13:48:10.0360] AppleSynopsysOTGDevice::gated_handleUSBCableConnect cable connected, but don't have device configuration yet
[13:48:10.0360] AppleMultitouchN1SPI: detected HBPP. driver will be kept alive
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableDetect 1
[13:48:10.0360] AppleD1972PMUPowerSource: AppleUSBCableType USBHost
[13:48:10.0360] AppleSynopsysOTGDevice::gated_handleUSBCableConnect cable connected, but don't have device configuration yet
[13:48:10.0360] display-scale = 2
[13:48:10.0360] display-rotation = 0
[13:48:10.0360] found applelogo at /usr/share/progressui/[email protected]
[13:48:10.0360] found display: primary
[13:48:10.0360] display: 640 x 1136
[13:48:10.0360] found PTP interface
[13:48:10.0360] AppleSynopsysOTGDevice - Configuration: PTP
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: PTP
[13:48:10.0360] AppleSynopsysOTGDevice - Configuration: iPod USB Interface
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: USBAudioControl
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: USBAudioStreaming
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: IapOverUsbHid
[13:48:10.0360] AppleSynopsysOTGDevice - Configuration: PTP + Apple Mobile Device
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: PTP
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: AppleUSBMux
[13:48:10.0360] AppleSynopsysOTGDevice - Configuration: PTP + Apple Mobile Device + Apple USB Ethernet
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: PTP
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: AppleUSBMux
[13:48:10.0360] AppleSynopsysOTGDevice          Interface: AppleUSBEthernet
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function USBAudioControl
[13:48:10.0360] IOAccessoryPortUSB::start
[13:48:10.0360] virtual bool AppleUSBDeviceMux::start(IOService *) build: Jun 11 2014 20:11:28
[13:48:10.0360] init_waste
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function AppleUSBMux
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function USBAudioStreaming
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function IapOverUsbHid
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function AppleUSBEthernet
[13:48:10.0360] AppleSynopsysOTGDevice::gated_registerFunction Register function PTP
[13:48:10.0360] AppleSynopsysOTGDevice::startUSBStack Starting usb stack
[13:48:10.0360] IOReturn AppleUSBDeviceMux::setPropertiesGated(OSObject *) setting debug level to 7
[13:48:10.0360] AppleBCMWLANCore::init(): IO80211-46 Jun 11 2014 20:10:03
[13:48:10.0360] [NAND] WMR_Open:420 FTL_Open    [OK]
[13:48:10.0360] [NAND] _publishServices:642 FTL capabilities: 0x00000001
[13:48:10.0360] [NAND] _ppnvflGetStruct:3469 Checking borrowed blocks - count: 23 max_count: 23
[13:48:10.0360] [NAND] _fetchBorrowedList:881 number of borrowed blocks 16
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 0
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 1
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 2
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 3
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 5
[13:48:10.0360] [nand_part_core:INF@ 157] published partition 6
[13:48:10.0360] 000828.945879 wlan.N[0] AppleBCMWLANCore::start(): Starting with MAC Address: <<<mac address>>>
[13:48:10.0360] 000828.946182 wlan.N[1] AppleBCMWLANCore::setPowerStateGated():   powerState 1, fStateFlags 0x20, dev 0xc476b000 (this 1, provider 0)
[13:48:10.0360] 000828.946197 wlan.N[2] AppleBCMWLANCore::setPowerStateGated(): Received power state change before driver has initialized, ignoring
[13:48:10.0360] IO80211Peer::addPhyStatistics Phy stats started for addr <<<mac address>>>
[13:48:10.0360] IO80211Peer::addPhyStatistics Tx Completion stats started for addr <<<mac address>>>
[13:48:10.0360] IO80211PeerManager::initWithInterface cant add monitoring timer
[13:48:10.0360] Started logging for intf
[13:48:10.0360] IO80211PeerManager::initWithInterface: inited peer manager
[13:48:10.0360] IO80211Interface::init peerManager=0x87cb8800
[13:48:10.0360] start:156
[13:48:10.0360] start:156
[13:48:10.0360] AppleARMBacklight::start: No AAP function
[13:48:10.0360] [effaceable:INIT] found current generation, 90, in group 1
[13:48:10.0360] [effaceable:INIT] started
[13:48:10.0360] [effaceable:INIT] started
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49152 62078<-usb->4608
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49153 62078<-usb->4864
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888adec8 established 62078<-lo0->49154 62078<-usb->5120
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade18 established 62078<-lo0->49155 62078<-usb->5376
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888adec8
[13:48:10.0360] recv(13, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade18
[13:48:10.0360] recv(14, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade18 established 62078<-lo0->49156 62078<-usb->5632
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49157 62078<-usb->5888
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49158 62078<-usb->6144
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49159 62078<-usb->6400
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49160 62078<-usb->6656
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49161 62078<-usb->6912
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49162 62078<-usb->7168
[13:48:10.0360] unrecognized key 'BootArgs' in value query
[13:48:10.0360] failed to handle value query for key 'BootArgs', sending back empty response
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49163 62078<-usb->7424
[13:48:10.0360] unrecognized key 'MarketingPartNumber' in value query
[13:48:10.0360] failed to handle value query for key 'MarketingPartNumber', sending back empty response
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] AppleUSBDeviceMux::handleConnectResult new session 0x888ade70 established 62078<-lo0->49164 62078<-usb->7680
[13:48:10.0360] void AppleUSBDeviceMux::handleMuxTCPInput(mbuf_t) received reset, closing 0x888ade70
[13:48:10.0360] recv(9, 4) failed: connection closed
[13:48:10.0360] unable to read message size: -1
[13:48:10.0360] could not receive message
[13:48:10.0360] client protocol version 13
[13:48:10.0360] *** UUID 4B2AC217-7071-EC47-8945-EB5E2188BE49 ***
[13:48:10.0360] Restore options:
[13:48:10.0360] UUID                           => <CFString 0x19315c0 [0x2f3ad0]>{contents = "4B2AC217-7071-EC47-8945-EB5E2188BE49"}
[13:48:10.0360] MinimumSystemPartition         => <CFNumber 0x1931510 [0x2f3ad0]>{value = +1660, type = kCFNumberSInt64Type}
[13:48:10.0360] SystemPartitionSize            => <CFNumber 0x1930f50 [0x2f3ad0]>{value = +1660, type = kCFNumberSInt64Type}
[13:48:10.0360] SystemPartitionPadding         => <CFBasicHash 0x192f3c0 [0x2f3ad0]>{type = mutable dict, count = 5,
[13:48:10.0360] entries =>
[13:48:10.0360] 2 : <CFString 0x1931540 [0x2f3ad0]>{contents = "128"} = <CFNumber 0x1931570 [0x2f3ad0]>{value = +1280, type = kCFNumberSInt64Type}
[13:48:10.0360] 3 : <CFString 0x1930f20 [0x2f3ad0]>{contents = "16"} = <CFNumber 0x192f3f0 [0x2f3ad0]>{value = +160, type = kCFNumberSInt64Type}
[13:48:10.0360] 4 : <CFString 0x192ede0 [0x2f3ad0]>{contents = "32"} = <CFNumber 0x1931250 [0x2f3ad0]>{value = +320, type = kCFNumberSInt64Type}
[13:48:10.0360] 5 : <CFString 0x1931960 [0x2f3ad0]>{contents = "8"} = <CFNumber 0x192ed50 [0x2f3ad0]>{value = +80, type = kCFNumberSInt64Type}
[13:48:10.0360] 8 : <CFString 0x1931180 [0x2f3ad0]>{contents = "64"} = <CFNumber 0x1931950 [0x2f3ad0]>{value = +640, type = kCFNumberSInt64Type}
[13:48:10.0360] }
[13:48:10.0360]
[13:48:10.0360] entering load_sep_os
[13:48:10.0360] device has no sep
[13:48:10.0360] entering partition_nand_device
[13:48:10.0360] device supports boot-from-NAND
[13:48:10.0360] nand device is already partitioned
[13:48:10.0360] entering wait_for_storage_device
[13:48:10.0360] Searching for NAND service
[13:48:10.0360] Found NAND service: IOFlashStoragePartition
[13:48:10.0360] NAND initialized. Waiting for devnode.
[13:48:10.0360] entering clear_remap_variable
[13:48:10.0360] executing /usr/sbin/nvram
[13:48:10.0360] entering format_effaceable_storage
[13:48:10.0360] effaceable storage is formatted, clearing it
[13:48:10.0360] effaceable storaged cleared
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] device partitioning scheme is GPT
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[13:48:10.0360] executing /sbin/fsck_hfs
[13:48:10.0360] AppleD1972PMUPowerSource: limiting USB input current to 390 mA (measured 462 mA)
[13:48:10.0360] ** /dev/rdisk0s1s1
[13:48:10.0360]    Executing fsck_hfs (version hfs-277.10.5).
[13:48:10.0360] ** Checking Journaled HFS Plus volume.
[13:48:10.0360] ** Detected a case-sensitive volume.
[13:48:10.0360]    The volume name is Sochi11D257.N42OS
[13:48:10.0360] ** Checking extents overflow file.
[13:48:10.0360] ** Checking catalog file.
[13:48:10.0360] ** Checking multi-linked files.
[13:48:10.0360] ** Checking catalog hierarchy.
[13:48:10.0360] ** Checking extended attributes file.
[13:48:10.0360] ** Checking volume bitmap.
[13:48:10.0360] ** Checking volume information.
[13:48:10.0360] ** Trimming unused blocks.
[13:48:10.0360] ** The volume Sochi11D257.N42OS appears to be OK.
[13:48:10.0360] executing /sbin/mount_hfs
[13:48:10.0360] mount_hfs: Could not create property for re-key environment check: No such file or directory
[13:48:10.0360] /dev/disk0s1s1 mounted on /mnt1
[13:48:10.0360] entering check_for_restore_log
[13:48:10.0360] found restore log (size = 28347)
[13:48:10.0360] entering unmount_filesystems
[13:48:10.0360] error unmounting '/mnt2': Invalid argument
[13:48:10.0360] entering clean_NAND
[13:48:10.0360] NAND format complete
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0 system= data=
[13:48:10.0360] entering format_storage_for_LwVM
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] device partitioning scheme is GPT
[13:48:10.0360] unexpected partition 'LwVM' - skipping
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0s1 system= data=
[13:48:10.0360] entering create_filesystem_partitions
[13:48:10.0360] User specified system partition size, skipping firmware extras size.
[13:48:10.0360] system partition padding size is: 167772160 bytes
[13:48:10.0360] unable to open : No such file or directory
[13:48:10.0360] creating 2 partitions
[13:48:10.0360] creating encrypted data partition
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] device partitioning scheme is GPT
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[13:48:10.0360] wipe entire partition: 1 (old = 0 new = 1820)
[13:48:10.0360] block size for /dev/disk0s1s1: 4096
[13:48:10.0360] /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[13:48:10.0360] executing /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[13:48:10.0360] Initialized /dev/rdisk0s1s1 as a 2 GB case-sensitive HFS Plus volume with a 8192k journal
[13:48:10.0360] block size for /dev/disk0s1s2: 4096
[13:48:10.0360] /sbin/newfs_hfs -s -v Data -J -P /dev/disk0s1s2
[13:48:10.0360] executing /sbin/newfs_hfs -s -v Data -J -P /dev/disk0s1s2
[13:48:10.0360] Initialized /dev/rdisk0s1s2 as a 13 GB case-sensitive HFS Plus volume with a 8192k journal
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] device partitioning scheme is GPT
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[13:48:10.0360] entering mount_filesystems
[13:48:10.0360] executing /sbin/fsck_hfs
[13:48:10.0360] ** /dev/rdisk0s1s1
[13:48:10.0360]    Executing fsck_hfs (version hfs-277.10.5).
[13:48:10.0360] ** Checking Journaled HFS Plus volume.
[13:48:10.0360] ** Detected a case-sensitive volume.
[13:48:10.0360]    The volume name is System
[13:48:10.0360] ** Checking extents overflow file.
[13:48:10.0360] ** Checking catalog file.
[13:48:10.0360] ** Checking multi-linked files.
[13:48:10.0360] ** Checking catalog hierarchy.
[13:48:10.0360] ** Checking extended attributes file.
[13:48:10.0360] ** Checking volume bitmap.
[13:48:10.0360] ** Checking volume information.
[13:48:10.0360] ** Trimming unused blocks.
[13:48:10.0360] ** The volume System appears to be OK.
[13:48:10.0360] executing /sbin/mount_hfs
[13:48:10.0360] mount_hfs: Could not create property for re-key environment check: No such file or directory
[13:48:10.0360] /dev/disk0s1s1 mounted on /mnt1
[13:48:10.0360] executing /sbin/fsck_hfs
[13:48:10.0360] ** /dev/rdisk0s1s2
[13:48:10.0360]    Executing fsck_hfs (version hfs-277.10.5).
[13:48:10.0360] ** Checking Journaled HFS Plus volume.
[13:48:10.0360] ** Detected a case-sensitive volume.
[13:48:10.0360]    The volume name is Data
[13:48:10.0360] ** Checking extents overflow file.
[13:48:10.0360] ** Checking catalog file.
[13:48:10.0360] ** Checking multi-linked files.
[13:48:10.0360] ** Checking catalog hierarchy.
[13:48:10.0360] ** Checking extended attributes file.
[13:48:10.0360] ** Checking volume bitmap.
[13:48:10.0360] ** Checking volume information.
[13:48:10.0360] ** Trimming unused blocks.
[13:48:10.0360] ** The volume Data appears to be OK.
[13:48:10.0360] executing /sbin/mount_hfs
[13:48:10.0360] mount_hfs: Could not create property for re-key environment check: No such file or directory
[13:48:10.0360] /dev/disk0s1s2 mounted on /mnt2
[13:48:10.0360] entering resize_system_partition_to_options
[13:48:10.0360] User specified system partition size, skipping firmware extras size.
[13:48:10.0360] Found SystemPartitionPadding value of 167772160 bytes
[13:48:10.0360] Erasing system partition prior to resize operation.
[13:48:10.0360] block size for /dev/disk0s1s1: 4096
[13:48:10.0360] /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[13:48:10.0360] executing /sbin/newfs_hfs -s -v System -J /dev/disk0s1s1
[13:48:10.0360] Initialized /dev/rdisk0s1s1 as a 2 GB case-sensitive HFS Plus volume with a 8192k journal
[13:48:10.0360] executing /sbin/fsck_hfs
[13:48:10.0360] ** /dev/rdisk0s1s1
[13:48:10.0360]    Executing fsck_hfs (version hfs-277.10.5).
[13:48:10.0360] ** Checking Journaled HFS Plus volume.
[13:48:10.0360] ** Detected a case-sensitive volume.
[13:48:10.0360]    The volume name is System
[13:48:10.0360] ** Checking extents overflow file.
[13:48:10.0360] ** Checking catalog file.
[13:48:10.0360] ** Checking multi-linked files.
[13:48:10.0360] ** Checking catalog hierarchy.
[13:48:10.0360] ** Checking extended attributes file.
[13:48:10.0360] ** Checking volume bitmap.
[13:48:10.0360] ** Checking volume information.
[13:48:10.0360] ** Trimming unused blocks.
[13:48:10.0360] ** The volume System appears to be OK.
[13:48:10.0360] executing /sbin/mount_hfs
[13:48:10.0360] mount_hfs: Could not create property for re-key environment check: No such file or directory
[13:48:10.0360] /dev/disk0s1s1 mounted on /mnt1
[13:48:10.0360] Trying to resize system partition to 1908408320 bytes aka 1820 MB
[13:48:10.0360] entering adjust_partition_preflight
[13:48:10.0360] partition:0 requiredSize=465920
[13:48:10.0360] no change in size
[13:48:10.0360] Successfully resized the system partition
[13:48:10.0360] entering maximize_data_partition
[13:48:10.0360] entering adjust_partition_preflight
[13:48:10.0360] partition:1 requiredSize=<<<<<IMEI>>>>>>6
[13:48:10.0360] maximizing data partition to 13946060799 bytes
[13:48:10.0360] entering adjust_partition_preflight
[13:48:10.0360] partition:1 requiredSize=3404800
[13:48:10.0360] no change in size
[13:48:10.0360] Successfully resized data partition to consume free blocks
[13:48:10.0360] The system partition now has a total HFS+ capacity of 1820 MB
[13:48:10.0360] entering ramrod_probe_media
[13:48:10.0360] device partitioning scheme is GPT
[13:48:10.0360] find_filesystem_partitions: storage=/dev/disk0s1 system=/dev/disk0s1s1 data=/dev/disk0s1s2
[13:48:10.0360] entering unmount_filesystems
[13:48:10.0360] entering ramrod_ticket_update
[13:48:10.0360] looking up root ticket hash
[13:48:10.0360] device tree ticket-hash: <CFData 0x1930040 [0x2f3ad0]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[13:48:10.0360] ticket_hash: <<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>
[13:48:10.0360] received valid ticket (2741 bytes)
[13:48:10.0360] entering restore_images
[13:48:10.0360] Successfully marked device node /dev/rdisk0s1s1 as static data
[13:48:10.0360] executing /usr/sbin/asr -source asr://localhost:12345 -target /dev/disk0s1s1 -erase -noprompt --chunkchecksum --puppetstrings
[13:48:10.0360] void AppleUSBDeviceMux::handleConnectResult(struct BulkUSBMuxSession *, errno_t) new session to port 12345 failed: 61
[13:48:10.0360] void AppleUSBDeviceM

Hello gamavranje,
Thanks for using Apple Support Communities.
The icons you're seeing on your iPhone indicate it is in recovery mode. Please plug your iPhone into your computer, and restore it with iTunes.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Use iTunes to restore your iOS device to factory settings
http://support.apple.com/kb/HT1414
Take care,
Alex H.

During update my ATV2 displayed icon to connect to iTunes. Now I have nothing -- can't even get to menu to do restart and ATV2 doesn't show up in iTunes menu to do restart from there. Help!

During update my ATV2 displayed icon to connect to iTunes. Now I have nothing -- can't even get to menu to do restart and ATV2 doesn't show up in iTunes menu to do restart from there. Help!

The update didn't apply correctly.
Did you follow the steps exactly in order to restore? disconnect all cables, open iTunes, then connect micro usb
Apple TV (2nd and 3rd generation): Restoring your Apple TV
Make sure to connect directly to computer, not a keyboard port or USB hub. Try a different cable.

Tomcat Servlet - TCP Port Already in Use?

My problem is that tomcat/servlet is not releasing its TCP port after my servlet closes the port. Next time a servlet tries to use the port it gets an error "Port already in use". Using netstat I can see the port is still in use. If I stop tomcat and restart it, the port is released. I have not had this sort of problem writing C programs that use sockets.
My setup is Fedora Core 6 with JDK1.5_14 and Tomcat 5.5.26. I know it's not the latest, but sockets and streams have been around for a long time.
Actual implementation uses a trivial javaserver page to instantiate a class to create/accept connection from a client (JApplet). After connection, it starts a thread to receive data. I am using ServerSocket(), InputStreamReader(), and OutputStreamWriter(). On ServerSocket I set ReuseAddress to true.
I have try/catch on all my I/O and use tomcat context log for error and OK messages. Data transfer is perfect. Detect close by client works. In the context log I see close of streams and ServerSocket occur with no exceptions. Then, I manually close the jsp window. No indication of any problems. If I use different port 2nd time (e.g. 50001) it all works perfect. If I use my default (50000) again, servlet gets an error during bind, "Port already in use".
2.5 years with Java. 5 years with Linux and C.
Please advise or refer

rwengr wrote:
My problem is that tomcat/servlet is not releasing its TCP port after my servlet closes the port. Next time a servlet tries to use the port it gets an error "Port already in use". Using netstat I can see the port is still in use. If I stop tomcat and restart it, the port is released. I have not had this sort of problem writing C programs that use sockets.Nice.... Not sure that matters though.
>
My setup is Fedora Core 6 with JDK1.5_14 and Tomcat 5.5.26. I know it's not the latest, but sockets and streams have been around for a long time.
Actual implementation uses a trivial javaserver page to instantiate a class to create/accept connection from a client (JApplet). Bleah! Don't use a JSP for that. Use a servlet at worst. At best use a Servlet to start some other socket manager class which you can/have tested outside the Servlet Container environment.
After connection, it starts a thread to receive data. I am using ServerSocket(), InputStreamReader(), and OutputStreamWriter(). On ServerSocket I set ReuseAddress to true.
I have try/catch on all my I/O and use tomcat context log for error and OK messages. Data transfer is perfect. Detect close by client works. In the context log I see close of streams and ServerSocket occur with no exceptions. Then, I manually close the jsp window. Closing the browser window has no affect on the server.
No indication of any problems. If I use different port 2nd time (e.g. 50001) it all works perfect. If I use my default (50000) again, servlet gets an error during bind, "Port already in use".
2.5 years with Java. 5 years with Linux and C.
Please advise or referShow some code. If you just want some generic advice it would be to close the port, as soon as you don't need it anymore. But you know that. Without any further code I think that is about all that can be said.
P.S. Make the code as small as possible, compilable, but still demonstrating the problem. Also see: [this tutorial as an example...|http://www.javaworld.com/javaworld/jw-12-1996/jw-12-sockets.html?page=1]

Airport Extreme Simultaneous Dual-Band port forwarding broken if only TCP ports with firmware 7.6.1

When configuring my Airport Extreme Simultaneous Dual-Band router, port forwarding is broken if you only specify TCP ports to forward. This is with firmware 7.6.1. What happens is that after you hit the Update button, when the router comes back and you open the port forwarding entry, the IP is still there but the port numbers are missing.
I tried all different port numbers and ranges and nothing would stick if i only specified TCP ports. If i added UDP ports with the TCP ports then it would save them. And if you add a new entry with only UDP it saves them too.
Now this is with adding a new port forwarding. I already have existing ports being forwarded that only have TCP. They are still working. I believe i added them with a previous version of the firmware.
Any one else see this issue? Any ideas?
Maybe i should perform a hard reset and reload a saved config.
Peace,
Dan

I haven't seen the issue but you could just downgrade to an earlier firmware:

HT5192 I cant update my mibile always i got the same message. An error occurrd during updating and sime times cannot establish connection ?!!!!

I cant update my mibile always i got the same message. An error occurrd during updating and sime times cannot establish connection ?!!!!

Hi Martha Leal Tapia,
Yes this issue was resolved. I had to add the below two parameters in the instance profile and continue the installation.
icm/server_port_1 = PROT = P4, PORT = 5$(SAPSYSTEM)04, HOST = <full hostname as in the /etc/hosts file>
icm/host_name_full=<full hostname as in the /etc/hosts file>
Note 1158626 P4 connection to ICM on machine with multiple IPs fails.
You can refer following SAPnote # 609603 for the above concepts although this refers to old release."
Thanks and regards
Ananth

Unlock TCP Port

Hello,
Does someone know how to free a used tcp port number ?
I mean after I kill an application listening on port number X, netstat shows that something is still listening on port X !!
How to stop this ?
Thank you in advance.

Thank you for your answers Juergen.
Here is what happened : on one of my production machines (Solaris 8 s28s_u7wos_08a SPARC), a new version of an application (a FIX Engine) was launched by mistake before the old version yesterday morning. Since they use same parameters, they listen to same TCP port.
That's why the current version aborted with a message : couldn't bind to port X : normal, it was used by the new version started by mistake.
So, I stopped the new one. I started the old one (irritating a couple of clients in the process), but the old one still abort with the same message (I'm sure no other process was using the port). I can't tell if netstat said TIME_WAIT (I think yes), but aftefr fighting for a few minutes, port mysteriously became avalable and the old version could be lauched normally.
I'm not a developper, so I'm not aware of all setsockopt stuff, only question : could I have spared some insults (and crescents I was forced to offer this morning) during the minutes I waited for the port to be available ?
Many thanks :-)

TCP Ports 24000-241000

Hello,
So I am an avid online scrabble player. Up until today I just logged on and played. No problem. But after installing a whole bunch of updates today, I am unable to go into scrabulous. It says I need to enable TCP ports 24000-24100. Now when I went to system preferences-->sharing-->firewall-->new--> then i made a new port on the tcp port numbers 24000-24100. I was very hopeful and proud of myself for figuring this out. But then I went back to the scrabble site and I got the exact same error message.
Please help!
I'm upset that I updated my computer and now it won't do one of its most important duties.
Thanks.

Are you using some sort of router with a firewall?

TCP port blocked

I am getting an "...unable to connect to server due to network security (TCP port 8080 blocked)" message. Any idea what settings should I change before going to SFR support? BES not enabled.

This will have been a false alarm triggered during the 7.7 upgrade. The warning occurs when a site fires an event but does not have a current heartbeat connection. I suspect this was caused by bad sequencing of a service restart and we will look into how that hapened. The upgrade started yesterday at 9am and was completed at noon US-CST.
Logs show a large number of these events were triggered between 9:30am and 10:20am CST. If you are still receiving these, please let us know so we can investigate further.
Andy

How to get the number of bytes at TCP port

Hi all,
How to get the number of bytes to read at the TCp port...as someone had suggested in some forum we do read the number of bytes first and then pass this...
but we get a problem when we have FF data in this...because then it sends 2 FF data...and cause of this we skip the last data...is there any solution for the same?

Hi
In LabVIEW you don't have the same property as in serail port.
You havn't "Byte at TCPIP port".
if you developp a protocol, one soltion, is to send the size to read.
Ingénieur d'Application / Développeur LabVIEW Certifié (CLD)
Application Engineer / LabVIEW Certified Developer (CLD)

TS3694 my iphone crashed during update now i have to restore but dont have my latest photos backed up ? i have a picture of itunes with the usb on my screen and cant go any further? is there a way to get it back without the update?

my iphone crashed during update now i have to restore but dont have my latest photos backed up ? i have a picture of itunes with the usb on my screen and cant go any further? is there a way to get it back without the update?

http://manuals.info.apple.com/en_US/iphone_user_guide.pdf
worth looking at for the future to understand backing up etc

IPod recognized, but hangs during update

So my iPod will show up in Finder and in iTunes, and automatic updating will begin. However, at random times during the update, sometimes 4 songs in, sometimes 65, the whole process will just hang. iTunes status screen gets stuck on flashing between "Updating iPod..." and Song 65 of 2054 and just flash between those two over and over.
Meanwhile, the iPod screen itself is also stuck and no longer flashing "Do Not Disconnect" -- it's a steady screen with none of the normal flashing.
Tried resetting, doesn't do anything.
Tried restoring, and it hangs after Authenticate asks me for my password to Restore the iPod.
I wind up having to just force disconnect and force quit everything and restart.
Anybody else have this problem? Thanks for any help you can give.
Oh btw, OS 10.3.9, iTunes 4.9, iBook G4.

I am having the same issue where it hangs during update -- seems to always happen around the 1800th song. Here's more specifics:
-I've got 7000 songs in my Library
-my iTunes Music folder is located on an external FireWire HD
My Mac has no problems mounting the iPod. No problems restoring with iPod Updater. No problems with erasing using Disk Utility.
I have tried the following:
1. Resetting and then restoring via iPod Updater.
2. Erasing/reformatting via Disk Utility, including zeroing out all data, and then restoring via iPod Updater.
3. Resetting into Disk Mode.
4. Manually updating songs.
5. Automatcially updating songs.
Nothing works. I have been troubleshooting this for about 8 hours now with no luck. No matter what I do differently, it always hangs around song 1800. I even tried uninstalling/reinstalling iTunes -- and I have tried this with several different user accounts and on different partitions I have set up.
When it "hangs," the iPod itself just makes a the "clicking" sound of a HD. I'm wondering if the HD is just bad -- but it came up with no errors when checking with Disk Utility.
Any more suggestions?
Johnny

Customer Coversion Using Interface Table - Error during update

I need to import customers from legacy applicatiion and is planning to use standard customer interface for that. For testing, I am able to create customers with hardcoded values. But while I try to update the same customer record (again using hard coded values), it gives me error and is not generating the error report as well. I am getting the following error during update:
racudc: ORA-20212: Enter valid Billing Fields.
ORA-06512: at "APPS.ADVOAR_CUST
racudc: Error updating customers.
or
racudc: updated 1 partiesracudc: Partyrel 1 parties
racudc: ORA-20210: You have edited one of the following fields, Extended Billi
racudc: Error updating customers.
Also it seems we can not update an address, site_use_code, or PRIMARY_SITE_USE_FLAG using customer interface.
The following is the test record I inserted for updating the customer I created and ran the customer interface:
insert into ra_customers_interface
(ORIG_SYSTEM_CUSTOMER_REF
,INSERT_UPDATE_FLAG
,CUSTOMER_NAME
,CUSTOMER_STATUS
,LAST_UPDATED_BY
,LAST_UPDATE_DATE
,CREATED_BY
,CREATION_DATE
,ORIG_SYSTEM_ADDRESS_REF
,ADDRESS1
,CITY
,COUNTY
,STATE
,POSTAL_CODE
,COUNTRY
,customer_attribute13
values
('APP1-492503' --ORIG_SYSTEM_CUSTOMER_REF
,'U' --INSERT_UPDATE_FLAG
,'Pizza Hut - CDH TEST4' --CUSTOMER_NAME
,'A' --CUSTOMER_STATUS
,-1 --LAST_UPDATED_BY
,sysdate --LAST_UPDATE_DATE
,-1 --CREATED_BY
,sysdate --CREATION_DATE
--,'Y' --PRIMARY_SITE_USE_FLAG
--,'BILL_TO' --SITE_USE_CODE
,'APP1-492503-ADDR1' --ORIG_SYSTEM_ADDRESS_REF
,'1 River Road, Bldg 1' --ADDRESS1
,'SCHENECTADY' --CITY
,'SCHENECTADY' --COUNTY
,'NY' --STATE
,12305 --POSTAL_CODE
,'US' --COUNTRY
,'55'
I am testing this in 11.5.10 env. Any help on this is appreciated.
Thanks,
MK

Convert only the data you need. And the data you need is probably less than you think. For example, other than open invoices (invoices for which money is still owed), you probably don’t need to convert ANY old invoices. You may want to convert data on what was purchased (e.g., event registration, membership, product, etc.) but the actual details (e.g., payment type, payment date) are probably no longer significant.
http://www.e-datapro.net/data_conversion.htm

Tcp ports during update

Similar Messages

Maybe you are looking for