Tecra 700CT - Need new AC adapter

I have a Tecra 700CT notebook and my adapter broke... can i use the PA3467E-1AC3 ac adapter on my laptop?
pls need answer very fast because i am about to buy one

Hi
Usually you should use the Toshiba recommend AC adaptor. In such case you are on the safe side.
But of course other updaters could functions but the properties must be the same.
The voltage value must be the same to avoid damage!!!
The ampere value could be a little bit higher but I recommend using always an AC adaptor which supports the same specifications!
By the way; as far as I know Toshiba has an own ASP in Romania.
You could contact the technicians in your country and could order the compatible one!!
Check this
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

Similar Messages

  • Need new power adapter for Qosmio F50

    Hello
    I am in need of buying new power adapter for my Qosmio F50 126. The reason being if I try to run more demanding application on my computer, the entire computer just crashes, shuts down. I need to buy a new adapter before my entire computers crashes result in destroying my HDD. I am not sure if my battery are died or the power adapter fails to charge them up.
    The picture of underside of my power adapter is shown below.
    https://www.dropbox.com/s/qcrk4fl5bhftbzm/IMG_20131220_215821_454.jpg
    What I would like to know if the following two adapters are the same and would work with my model. I ask this because the price difference between the two units is significant., 20 USD. Also, I will be importing it from the USA using an agent here. Therefore I need to get it right on the first try.
    I'm curious about the connecter it has on the end. I wonder if its same as the one which came with the notebook. I believe it wont be an issue with it clearly says it supports my model, Qosmio F50 126
    Another find which I believe is the best and most compatiable.
    This one will sure work but the price is much higher than the one mentioned above
    Regards
    Abdusamed
    +Message was edited: link to onlineshops has been removed - advert+

    Hi
    You need an AC adaptor which supports *19V and 6.32A*
    The Ampere value might be a little bit different. This should not be a big problem but you have to ensure the Ampere value isnt too low. The notebook needs enough power to run properly and to charge the battery.
    However, the Volt value (19V) cannot be different. _It has to be *19V_*
    The original AC adaptor has the part number: *PA3290E-3AC3*
    I recommend you to purchase the AC adaptor recommended by Toshiba.

  • X100e - Not Charging (Do I need new AC adapter?)

    So I've had an x100e (and its original AC adapter) since 2010 and all of a sudden the battery stopped charging and slowly drained, so its obviously not a problem with the battery.
    The ac adapter used to cause a few sparks  at the metal parts of the plug when plugging it in, but not anymore. Silence.
    Do I need a new adapter?
    Where can I get one?

    Thanks for the response.
    Luckily I have a voltmeter, but sadly, it is not providing a reading on any part of the inside or outside of the barrel. There's definitely no electricity going through the adapter. The box part does not heat up while plugged in.
    Now, I've been looking for new adapters, and there are two that look similar but have different wattages. There's 90W and 65W (same as the one that came with the laptop). Which one is recommended?

  • Equium U400-145 - Need new AC adapter

    Hi,
    AC adapter part no. is PA3468E-1AC3
    Model No. is pa-1750-09
    I need to replace the power adapter, however I'm am unsure of the power rating required is 75w or 90w?
    Input is 240V
    Output is 19V
    Thanks

    Hmm... And why you dont buy the same AC adapter again? Are you not satisfied with it?
    I mean if you search with this part number on Google you will find some online shops where you can buy this adapter.
    Furthermore you can buy new original Toshiba parts from an authorized service provider.
    Check this!!!

  • Defective Tecra S11 - Need new notebook with Express-Card-Slot

    My TECRA-S11-166 is faulty.
    I need a new Notebook with *Express-Card-Slot* and (if its possible) RS232.
    What kind of Notebook comes with a Express-Card-Slot ?

    Hi
    There are different Toshiba notebooks on the market and Toshiba releases new models in very short intervals.
    I would recommend you to visit the Toshiba notebook product page and to compare the available series and models.
    The Tecra laptops offer a business professional use and Portege series are very best in mobile computing.
    The Satellite series are entertainment machines designed to provide exceptional all-round performance.
    http://www.toshiba.eu/laptops/

  • Need new AC adapter for my Qosmio F10-124

    Hi All,
    I am a bit of a novice when it comes to this but can anyone tell me the product/part number of a suitable replacement AC power adaptor as mine has become faulty.
    Any help welcome.

    Do you know the Toshiba Options & Accessories website?
    http://eu.computers.toshiba-europe.com -> Products -> Options and Accessories
    There you can find all details about compatible products with your Qosmio F10

  • Do i need a new charge adapter after updateing my i phone 3

    do i need a new charge adapter after updating my i phone 3.

    What do you mean by "updating"?  If you mean "updating the software", the answer is no.  If you mean buying a newer iPhone, the answer dpends upon which newer model you bought.

  • I need a new wifi-adapter/wifi-card

    Hi everyone...
    I'm currently thinking of buying a new wlan-adapter...
    At the moment I got a D-Link DWL-122 (11Mbps)
    The worst thing on this USB-dongle is that there are no Linux driver available (I got to use ndiswrapper).
    Another problem is the speed:
    I'm here on the second floor, but my router is in the cellar.
    My maximum link quality (got this value from iwconfig) is 42%.. - BUT: I've put some CD's on my USB-dongle to get a better link quality... (this works!)
    Without the CD's I only got ~30% (that's not enough to connect to the router).
    Now I've been looking for a new wlan-adapter...
    It don't has to be an USB-dongle, but there should be Linux drivers for the card/dongle (not with ndiswrapper!).
    I've searched a bit and I found one pci-card and one USB-dongle that would fit (I'm not a wireless-pro!):
    FRITZ!WLAN USB Stick (http://www.avm.de/en/Produkte/FRITZBox/ … index.html):
    802.11g++ (125 Mbit/s)
    costs ~35 Euro (shipping included)
    Chipset: AVM (they provide a linux-driver on their website!)
    Super G & eXtended Range 108M Wireless PCI Adapter (http://www.tp-link.com/products/product_des.asp?id=17):
    802.11a/b/g
    costs ~24 Euro (shipping included)
    Chipset: Atheros (linux-driver: madwifi)
    Suggestions for other wifi-adapters are of course welcome, but note that the wlan-adapter should give me a good connection...!
    (I'm here on the second floor and my router is in the cellar)
    Another criteria is that it shouldn't cost more than 35 Euro.
    It doesn't matter if it's a USB-dongle or a pci-card (I don't have a pcmcia slot because this is my workstation)
    Oh, and one last thing: I live in Germany... (if this is important)
    Thanks in advance...
    XazZ

    Hi everyone again...
    I forgot to tell you which router I got...
    It's a AVM Fritz!Box Fon WLAN 7050 (very nice thing )
    Here is it's product page: http://www.avm.de/en/Produkte/FRITZBox/ … index.html
    My router is from the same manufacturer as the USB-dongle I showed above...
    USB-dongle and router support 802.11g++ (125 Mbit/s)...
    But I think the pci-card has the better antenna...
    Keep in mind that I don't know very much about wireless networking...
    Thanks in advance..
    XazZ

  • Do I need an active adapter for my third monitor? (GTX 770)

    I have a GTX 770 and with it a 2560x1440 monitor is connected through Dual-DVI.
    I want to connect my TV and a second 22" computer screen to my graphics card. The MSI 770 Gaming has this:
    Dual-link DVI-I x 1
    Dual-link DVI-D x 1
    DisplayPort x 1 (version 1.2)
    HDMI x 1 (version 1.4a)
    Is it possible to connect my screens so that I do not need an active adapter? Let's say the 27" screen goes to a Dual Link DVI, the TV connects to HDMI, and the 22" screen connects to either the last Dual Link DVI or the DisplayPort.
    Is this possible?

    If Vodafone operates anything like AT&T here in the States, once the SIM has been inactivated by the carrier, you would need a new one. I usually get a new SIM when I swap phones. I may be supersticious, but I think it reduces problems.

  • New power adapter for old macbook - It doesn't work!

    Hello!
    My MacBook is 3 years old. My power adapter got broken at the end where you put it into the socket.
    Now I bought a new power adapter. The adapters have changed now. The end where you put it into the computer looks now a little bit different. But they told me in the Apple Store that it will also fit my 3 years old Macbook.
    At home it really fit my Macbook but it didn't charge. Nothing happened, no light. How can that be? Then I combined the two, the end for the socket of the new power adapter and the other part where you put it into the computer of my old power adapter. Now it charges. So is the problem after all the part where you put it into the computer of the new power adapter that looks different now?
    Or what can I try now?
    Thank you for help!
    Sorry for my bad English.
    xenchen
    Message was edited by: xenchen

    You may need to download and install the SMC firmware update:
    http://support.apple.com/kb/DL1312?viewlocale=en_US

  • Zen Vision M 30GB - New Synch Adapter and Char

    Hi,
    I need a new synch adapter and charger for my Creative Vision M 30 GB.
    Im in Australia and have been unable to locate it at any of the retailers that Creative have specified.
    Im wondering if I can get one directly from Creative, or is this all a ploy to force me to get a new player
    Thanks,
    John?

    Ebay or ? google search engine.

  • New file adapter

    Hi,
    I need to create a new file adapter.
    I've read some documentations that say PCK could be used. Is that mandatory?
    I've also found some code sample.
    But I still don't know what to modify in a the sample nor how to deploy my new adapter in order to select it in XI's directory part.
    Regards
    Yann

    Hi Yann,
    I am not sure whether I have understood you correctly..Do u want to create a new file adapter itself, or write an adapter module for a file adapter?
    Please take a look at these..
    http://help.sap.com/saphelp_nw04/helpdata/en/e9/61e1407e858031e10000000a1550b0/frameset.htm
    https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/da5675d1-0301-0010-9584-f6cb18c04805
    cheers,
    Prashanth
    P.S Please mark helpful answers

  • HT4060 Need to plug adapter few times with no reaction tell finaly it starts charging .is this normal ?

    The charging speed is ok but i need to plug the iPad to the included adapter few time with no reaction tell finaly it starts charging .is this normal ?

    Hi. I would suggest carefully examining your cable at both ends where the cable connects with the USB Plug and other side where the cable connects to the Apple port. Making sure that there are no breaks in the insulation or any wires showing at all. It just may be an issue of replacing the apple cable, which you can order and easily have shipped to you.
    Frayed connections on either ends can happen if someone trips over connected power cable and it gets yanked while still connected to ipad for example.
    Another thing may be just simply doing as Diavonex suggested. And trying a different outlet. I would add trying a different outlet that is on a different circuit then the one you are currently using.
    Only other possibilities besides a frayed cable, or a bad wall outlet, would be don't plug your adapter into some thin household extension cord with the three outlets on its far end as an extension point.
    And possibly check for dirt in the adapter USB port side and corrosion on the adapters electric prongs. Also check your cable connectors for same kind've dirt and corrosion. Especially for gritty type dust that may have gotten into your connection points. Considering that you seem to be experiencing an intermittent power connection, I would really suggest checking and possibly cleaning very gently and carefully your adapters USB port, and your cables USB plug, which is where it seems you are having your connectivity issues.
    if you experience this again i suggest just ordering a complete new Apple adapter and a new Apple cable. It is easier then cleaning the ports.
    Lastly, How good is the quality of the electricity that your electric company provides? Any other troubles with other appliances or TV's, etc? It's only a tiny and slight chance but if you are experiencing other electrical intermittent problems then it may be remotely possible that the quality of electricity you are receiving from your provider is rather poor and that is responsible for your problems with your adapter.
    Hope some of this helps you! Cheers!

  • Urgent help needed - new to Macs, accidently cut and paste over top of photo folder and now no sign of folder or file, no auto back-up in place, how can I restore photos pls

    Urgent help needed - new to Macs, accidently cut and paste over top of photo folder and now no sign of folder or file, no auto back-up in place, how can I restore photos pls

    Thanks for prompt reply, yes we have tried that but have now closed down the browser we where the photos were.
    We haven't sent up time machine, do you know whether there is any roll-back function on a Mac?
    Thanks

  • I can't open a doc in Pages, msg says I need "newer version of Pages" but it's already downloaded and updated. Help plse

    I can't open a doc in Pages, msg says I need "newer version of Pages" but it's already downloaded and updated. Help plse

    You have 2 versions of Pages on your Mac.
    Pages 5.2 is in your Applications folder.
    Pages '09/'08 is in your Applications/iWork folder.
    You are alternately opening the wrong versions.
    Pages '09/'08 can not open Pages 5 files and you will get the warning that you need a newer version.
    Pages 5.2 can open Pages '09 files but may damage/alter them. It can not open Pages '08 files at all.
    Older versions of Pages 5 can not open files from later versions of Pages 5.
    Once opened and saved in Pages 5 the Pages '09 files can not be opened in Pages '09.
    Anything that is saved to iCloud and opened in a newer version of Pages is also converted to Pages 5 files.
    All Pages files no matter what version and incompatibility have the same extension .pages.
    Pages 5 files are now only compatible with themselves on a very restricted set of hardware, software and Operating Systems and will not transfer correctly on any other server software than iCloud.
    Apple has removed almost 100 features from Pages 5 and added many bugs:
    http://www.freeforum101.com/iworktipsntrick/viewforum.php?f=22&sid=3527487677f0c 6fa05b6297cd00f8eb9&mforum=iworktipsntrick
    Peter

Maybe you are looking for

  • Changing the Purchasing grp in SOCO

    Hi All, we are on SRM 5.O ECS We have plan driven procurement, PS based reqs flow in to SRM for further procurement process. As per standard criteria , for a certain matgrp, purgrp, external requirements flow in to SRM. At this time, we have asterik

  • How do I transfer my details from one iMac to another

    How do I transfer my details from one imac to a new one

  • Can't remove, update or re-install quicktime

    I recently had video problems and using the typical check uninstalled the most recent thing before the trouble which happened to be the iTunes version of Quicktime. I uninstalled the iTunes version and tried putting the stand alone back on, said newe

  • Script to Change swatch CMYK values

    Are there any scripts available to change CMYK values of swatches for files in CS3? I have hundreds, probably thousands of Illustrator EPS files that use swatches all drawn from a total palette of maybe 50 colours. Each colour is named and has a corr

  • Need help with Adobe Interactive Forms

    Hi Gurus, In my Adobe Form, I have large data and I need to add new body page horizontally after my Master Page. Can any body help me? Regards, Srini