Tecra a2: freebsd 5.3 hang at boot

hello
can i use freebsd 5.3 on tecra a2 laptop?
Mode no PTA20E-02F02YPL
freebsd stops while botting at this line
pci0: <ACPI PCI bus> on pcib0
i tried to boot without ACPI, Safe mode, didn't help.

Hi,
here are some interesting linux sites
http://www.linux-on-laptops.com
http://newsletter.toshiba-tro.de/main/index.html
There are lists of hardware compability.
thanks to Bob :)
bye

Similar Messages

  • Hangs during boot after upgrading to Kernel 2.6.39

    I have just installed Arch on a new computer. It works fine until I upgrade to Kernel 2.6.39. After that it hangs on boot.
    The end of /var/log/everything.log is posted below.
    Jul 26 23:52:06 localhost kernel: [ 6.036766] [drm] nouveau 0000:04:00.0: Parsing VBIOS init table at offset 0x85F3
    Jul 26 23:52:06 localhost kernel: [ 6.129046] adt7475 1-002e: ADT7473 device, revision 1
    Jul 26 23:52:06 localhost kernel: [ 6.138997] [drm] nouveau 0000:04:00.0: Detected monitoring device: adt7473
    Jul 26 23:52:06 localhost kernel: [ 6.139000] [drm] nouveau 0000:04:00.0: 1 available performance level(s)
    Jul 26 23:52:06 localhost kernel: [ 6.139002] [drm] nouveau 0000:04:00.0: 0: memory 405MHz core 270MHz shader 540MHz
    Jul 26 23:52:06 localhost kernel: [ 6.139233] [TTM] Zone kernel: Available graphics memory: 12371030 kiB.
    Jul 26 23:52:06 localhost kernel: [ 6.139236] [TTM] Zone dma32: Available graphics memory: 2097152 kiB.
    Jul 26 23:52:06 localhost kernel: [ 6.139238] [TTM] Initializing pool allocator.
    Jul 26 23:52:06 localhost kernel: [ 6.139252] [drm] nouveau 0000:04:00.0: Detected 5376MiB VRAM
    Jul 26 23:52:06 localhost kernel: [ 6.139260] mtrr: type mismatch for d0000000,8000000 old: write-back new: write-combining
    Jul 26 23:52:06 localhost kernel: [ 6.150626] [drm] nouveau 0000:04:00.0: 512 MiB GART (aperture)
    Jul 26 23:52:06 localhost kernel: [ 6.152371] [drm] nouveau 0000:04:00.0: failed to load fuc409d
    Jul 26 23:52:06 localhost kernel: [ 6.176193] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    Jul 26 23:52:06 localhost kernel: [ 6.176195] [drm] No driver support for vblank timestamp query.
    Jul 26 23:52:06 localhost kernel: [ 6.228800] No connectors reported connected with modes
    Jul 26 23:52:06 localhost kernel: [ 6.228802] [drm] Cannot find any crtc or sizes - going 1024x768
    Jul 26 23:52:06 localhost kernel: [ 6.231002] [drm] nouveau 0000:04:00.0: allocated 1024x768 fb: 0x8020000, bo ffff880608d97800
    Jul 26 23:52:06 localhost kernel: [ 6.233786] Console: switching to colour frame buffer device 128x48
    Jul 26 23:52:06 localhost kernel: [ 6.235094] fb0: nouveaufb frame buffer device
    Jul 26 23:52:06 localhost kernel: [ 6.235094] drm: registered panic notifier
    Jul 26 23:52:06 localhost kernel: [ 6.235098] [drm] Initialized nouveau 0.0.16 20090420 for 0000:04:00.0 on minor 0
    Jul 26 23:52:06 localhost kernel: [ 6.255449] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    Jul 26 23:52:06 localhost kernel: [ 6.255451] hda_intel: Disable MSI for Nvidia chipset
    Jul 26 23:52:06 localhost kernel: [ 6.255599] HDA Intel 0000:04:00.1: setting latency timer to 64
    Jul 26 23:52:06 localhost kernel: [ 7.663482] EXT4-fs (sda3): re-mounted. Opts: (null)
    Jul 26 23:52:06 localhost kernel: [ 7.807508] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
    Jul 26 23:52:06 localhost kernel: [ 7.851401] Adding 265068k swap on /dev/sda2. Priority:-1 extents:1 across:265068k
    Jul 26 23:52:06 localhost kernel: [ 8.569682] r8169 0000:08:00.0: eth0: link down
    Jul 26 23:52:06 localhost kernel: [ 8.569687] r8169 0000:08:00.0: eth0: link down
    Jul 26 23:52:06 localhost dhcpcd[747]: eth0: waiting for carrier
    Jul 26 23:52:08 localhost dhcpcd[747]: eth0: carrier acquired
    Jul 26 23:52:08 localhost kernel: [ 10.301736] r8169 0000:08:00.0: eth0: link up
    Jul 26 23:52:08 localhost dhcpcd[747]: eth0: broadcasting for a lease
    Jul 26 23:52:12 localhost dhcpcd[747]: eth0: offered 131.181.53.42 from 131.181.127.32
    Jul 26 23:52:13 localhost dhcpcd[747]: eth0: acknowledged 131.181.53.42 from 131.181.59.48
    Jul 26 23:52:13 localhost dhcpcd[747]: eth0: checking for 131.181.53.42
    Jul 26 23:52:18 localhost dhcpcd[747]: eth0: leased 131.181.53.42 for 43200 seconds
    Jul 26 23:52:18 localhost dhcpcd[747]: forked to background, child pid 774
    Jul 26 23:52:18 localhost crond[823]: /usr/sbin/crond 4.5 dillon's cron daemon, started with loglevel info
    Jul 26 23:53:01 localhost crond[823]: FILE /etc/cron.d/prune-cronstamps USER root PID 835 job prune-cronstamps
    Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 836 job sys-hourly
    Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 837 job sys-daily
    Jul 26 23:53:01 localhost crond[823]: FILE /var/spool/cron/root USER root PID 838 job sys-weekly
    Any help fixing this would be greatly appreciated.

    I have been trying to isolate the problem a little further. I re-installed (with just the base and sudo) and after upgrading pacman rebooted and it worked without fail. Then I installed libusb and libusb-compat which where required when I tried to upgrade just the kernel using
    pacman -S kernel26
    which initially failed because of the missing dependencies libusb and libusb-compat. I then re-booted and that worked without a problem.
    I then upgraded to Kernel 2.6.39 using the above command and then it hung on rebooting. I saved the logs at each stage.
    The additional logs in errors.log in the reboot that failed are as follows.
    ul 26 16:28:39 O313 kernel: [ 5.120698] [drm] nouveau 0000:04:00.0: Pointer to BIT loadval table invalid
    Jul 26 16:28:39 O313 kernel: [ 5.360508] [drm] nouveau 0000:04:00.0: failed to load fuc409d
    Jul 26 16:28:39 O313 kernel: [ 5.808016] sd 20:0:0:0: [sdb] Assuming drive cache: write through
    Jul 26 16:28:39 O313 kernel: [ 5.809960] sd 20:0:0:0: [sdb] Assuming drive cache: write through
    Jul 26 16:28:39 O313 kernel: [ 5.812116] sd 20:0:0:0: [sdb] Assuming drive cache: write through
    Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
    The end of kernel.log is as follows:
    Sat Jul 9 14:57:41 CEST 2011
    Jul 26 16:28:39 O313 kernel: [ 0.000000] Command line: root=/dev/disk/by-uuid/e4733c60-3e54-4001-a83e-415b690dfcb0 ro
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-provided physical RAM map:
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cfed0000 (usable)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed0000 - 00000000cfed1000 (ACPI NVS)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfed1000 - 00000000cfee0000 (ACPI data)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000cfee0000 - 00000000cff00000 (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000630000000 (usable)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] NX (Execute Disable) protection: active
    Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI 2.4 present.
    Jul 26 16:28:39 O313 kernel: [ 0.000000] DMI: Gigabyte Technology Co., Ltd. X58A-UD5/X58A-UD5, BIOS FD 02/01/2011
    Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    Jul 26 16:28:39 O313 kernel: [ 0.000000] No AGP bridge found
    Jul 26 16:28:39 O313 kernel: [ 0.000000] last_pfn = 0x630000 max_arch_pfn = 0x400000000
    And this is the end of daemon.log
    Jul 26 16:27:49 O313 init: Switching to runlevel: 6
    Jul 26 16:27:50 O313 dhcpcd: received SIGTERM, stopping
    Jul 26 16:27:50 O313 dhcpcd: eth0: removing interface
    Jul 26 16:28:39 O313 2.352592] udevd[87]: starting version 171
    Jul 26 16:28:39 O313 4.531007] udevd[370]: starting version 171
    Jul 26 16:28:39 O313 dhcpcd: version 5.2.2 starting
    Jul 26 16:28:39 O313 dhcpcd: eth0: waiting for carrier
    Jul 26 16:28:35 O313 udevd[369]: error: runtime directory '/run/udev' not writable, for now falling back to '/dev/.udev'
    Jul 26 16:28:39 O313 init: Entering runlevel: 3
    Please let me know if any further information would be useful in tracking down this problem. Also ignore any timings in my initial post they were incorrect.
    Last edited by TheStatsMan (2011-07-26 07:40:48)

  • HP Pavilion Media Center m8300f Hangs on boot

    I have a HP Pavilion Media Center m8300f which came loaded with Vista Home Premium. About 18 month sold. Recently the computer would hang on boot up. I used the system restore and went back to a safe install. This worked ok until Windows added more patches which caused the same problem to occur again. After one or two of these episodes I was not longer able to return to a safe install. I ran the system recovery several times to check the hardware. Everything turned up good. Since I did not have a good set of recovery disks I decided to install XP on the computer and then upgrade to Vista. XP installed without a single problem. I purchased a NEW Vista Home Premium because I could later upgrade free to Windows 7. I tried to install Vista over XP. The process would start and then hang. So I reformated the hard drive using an external USB unit on another computer, replaced the drive and tried to install Vista off the DVD. It would not boot up. As a test using the Vista DVD I purchased, I upgraded XP on a separate computer to Vista. Worked very nice.
    I ordered a set of the recovery DVDs and tried them. They would not boot up. I replaced the hard drive with a new SEAGATE SATA drive because I felt the connectors were not locking in. I still could not get the recovery DVDs to run. I went back to the XP and it installed. So here I am with a computer that willl not run or install Vista but will run XP. Also HP does not provide the XP drivers for the hardware on this computer.
    Does anyone know why Vista will not install or how to get it on this computer?
    I installed a NEW Seagate SATA hard drive for drive "C" because the connectors where not locking in place. rmated the hardI purchased the Recovery DVDs from HP and tried to reinstall it.

    I had the same problem with computer halting with blue screens, black screens, etc.  Motherboard had 6 capacitors with bulging tops.  I found a replacement Nettle 2 motherboard from seller diypc2008 on E-Bay for the cost of $75.00 with free shipping.  Installed new motherboard and computer works like new. 
    It appears like at around 2 years, this problem occurs from what I read on this forum.  Look for capacitors on the motherboard with bulging tops.  I fixed my computer by replacing motherboard after running many hours of diagnostics, replacing power supply, and changing out drives.

  • [SOLVED] New installation hangs on boot at two different places

    Hello
    I recently made my another attempt at installing arch on a new desktop build. Previous successful attempts were old laptops.
    I followed the Beginner's Guide on the Arch wiki.
    Currently it stops at one of two places in the boot process:
    1. [ OK ] Found device Samsung_SSD_850_EVO_500GB BOOTARCH
        Starting File System Check on /dev/sdb6…
    2.  [ OK ] Started Journal Service
        [ OK ] Started udev Kernel Device Manager
    I can not consistently recreate either scenario, but it seems to be random which of the two places it stops. Cold boot and CTRL ALT Delete. I doubt that has anything to do with it, but thought I'd add it anyway.
    Current setup:
    Hardware:
    Motherboard - ASUS Z97 Pro (using ethernet adapter and sound on here)
    Processor - Intel 4790K
    Memory - 16 GB
    Graphics - Gigabyte G1 Nvidia GTX 970 SLI x2
    Storage - Samsung 850 SSD 500 GB and WD Black HDD 3 TB
    I've also configured it to use a static IP
    I started this journey by using the live Gparted CD to create partitions. I created two partitions on the SSD. One for windows 8.1 and one for linux. I then created two partitions on the HDD. One for windows, one for linux.
    I installed windows 8.1 first. It divided up the partition I gave it. I am able to run Windows. Once that was done I began installing Arch.
    I used the Feb 2015 ISO from the torrent.
    Current partition scheme for linux:
    sda1 /home
    sda3 /swap
    sda4 /var
    sdb1 /
    sdb6 /boot
    sda is the HDD and sdb is the SSD
    The other partitions not listed are for windows. To boot into windows, I use F8 to choose the windows boot manager partition. It currently defaults to the linux partition.
    During the install, I mounted the root partition first. I then created directories for each of the other partitions and then mounted them. Home, var, and root are all ext4. Boot is FAT32, and Swap is swap.
    I read where I made a couple of mistakes the first attempt on this computer and did a wipe and reinstall again. First mistake was not knowing that /boot needed to be FAT. I then learned that /swap does not need to be in the fstab. I also learned that a FAT partition can not use UUID in the fstab so I took that out and just used /dev/sdb6 instead.
    I have run out of things to search for at this point and need help to continue moving forward.
    Bellow is the current /etc/fstab. It was generated using
    genfstab -U -p /mnt >> /mnt/etc/fstab
    and then edited as noted above
    #/dev/sdb1 LABEL=archroot
    UUID=xxxxxxxxxxxxxxx / ext4 rw,relatime,data=ordered 0 1
    #/dev/sdb6 LABEL=BOOTARCH
    #UUID=xxxxxxxxx
    /dev/sdb6 /boot vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro 0 2
    # /dev/sda1 LABEL=linux\134x20home
    UUID=xxxxxxxx /home ext4 rw,relatime,data=ordered 0 2
    #/dev/sda4 LABEL=archvar
    UUID=xxxxxxxxxx /var ext4 rw,relatime,data=ordered 0 2
    #/dev/sda3
    #UUID=xxxxxxxxxxxxxx none swap defaults 0 0
    Thanks for any help that can be provided
    Jason
    Last edited by p2ranger (2015-02-14 22:20:14)

    I tried removing gummiboot and installed GRUB2. That didn't work.
    As to the UUID's, I just typed in xxxxx's for the post because I didn't feel like transcribing random letters and numbers.
    So after reading Head_on_a_Stick's suggestion, I redid my partitions and reinstalled arch again following the Beginner's wiki page and using gummiboot
    New Partitions are as follows:
    sda1  /home
    sda3  /swap
    sda4  /var
    sdb1  /
    sdb3  /boot (originally created from windows install)
    Also, I took a screenshot from Gparted of the two disks if there is any info on there that may be of use
    http://cotting.us/gparted-sda.jpg
    http://cotting.us/gparted-sdb.jpg
    Below is the contents and output requested
    arch.conf
    title Arch Linux
    linux /vmlinuz-linux
    initrd /initramfs-linux.img
    options root=/dev/sdb1 rw
    loader.conf
    timeout5
    #default 875966af283d44de9e754c1d68848eab-*
    default arch
    gdisk -l /dev/sda
    GPT fdisk (gdisk) version 0.8.10
    Partition table scan:
    MBR: protective
    BSD: not present
    APM: not present
    GPT: present
    Found valid GPT with protective MBR; using GPT.
    Disk /dev/sda: 5860533168 sectors, 2.7 Tib
    Logical sector size: 512 bytes
    Disk identifier (GUID): E11d436B-ED6D-47AD-BCD0-F04384ED50B8
    Partition table holds up to 128 entries
    First usable sector is 34, last usable sector is 5860533134
    Partitions will be aligned on 2048-sector boundaries
    Total free space is 2925 sectors (1.4 MiB)
    Number Start (sector) End (sector) Size Code Name
    1 2048 45672447 21.8GiB 8300
    2 2871662592 5860532223 1.4 TiB 0700
    3 2854432768 2871662591 8.2 GiB 8200
    4 45672448 285443277 1.3 TiB 8300
    gdisk -l /dev/sdb
    GPT fdisk (gdisk) version 0.8.10
    Partition table scan:
    MBR: protective
    BSD: not present
    APM: not present
    GPT: present
    Found valid GPT with protective MBR; using GPT.
    Disk /dev/sda: 5860533168 sectors, 465.8 GiB
    Logical sector size: 512 bytes
    Disk identifier (GUID): DA9A6AF9-066B-4C1A-8778-93CCE5A68D97
    Partition table holds up to 128 entries
    First usable sector is 34, last usable sector is 976773134
    Partitions will be aligned on 2048-sector boundaries
    Total free space is 2029 sectors (1014.5 KiB)
    Number Start (sector) End (sector) Size Code Name
    1 2048 410247167 195.6 GiB 8300
    2 410247168 410861567 300.0 MiB 2700 Basic data partition
    3 410861568 411066367 100.0 MiB EF00 EFI system partition
    4 411066368 411328511 128.0 MiB 0C01 Microsoft reserved …
    5 411328512 976773119 269.6 GiB 0700 Basic data partition
    lsblk -f
    sda
    -sda1 /home
    -sda2
    -sda3 [SWAP]
    -sda4 /var
    sdb
    -sdb1 /
    -sdb2
    -sdb3 /boot
    -sdb4
    -sdb5
    sdd
    -sdd1
    -sdd2
    sr0
    loop0
    loop1
    -arch_airootfs /etc/resolv.conf
    loop2
    -arch_airootfs /etc/resolv.conf
    Since my fstab is changed, here is the new one
    # /dev/sdb1 LABEL=archroot
    UUID=xxxxxxxxxxxxxxxxxx / ext4 rw,relatime,data=ordered 0 1
    # /dev/sdb3
    #UUID=xxxxxxxx
    /dev/sdb3 /boot vfat rw,relatime,fmask=0022,dmask=0022, codepage=437,iocharset=iso8859-1, shortname=mixed, errors=remount-ro 0 2
    # /dev/sda1 LABEL=archvar
    UUID=xxxxxxxxxxxxxxxxxx /home ext4 rw,relatime,data=ordered 0 2
    # /dev/sda4 LABEL=archome
    UUID=xxxxxxxxxxxxxxxxx /var ext4 rw,relatime,data=ordered 0 2
    # /dev/sda3
    #UUID=xxxxxxxxxxxxxxx none swap defaults 0 0
    After another install, it still hangs on booting. Here are some of the last lines it displays:
    ( OK ) Started create system users
    Starting Create static device nodes in /dev...
    ( OK ) Started Journal service.
    ( OK ) Started create static device nodes in /dev.
    ( OK ) Reached target Local File systems (Pre).
    ( OK ) Started Rebuild hardware database
    Starting udev Kernel Device Manager....
    ( OK ) Started Rebuild Dynamic linker cache
    ( OK ) Started udev Kernel Device Manager
    I’m glad people like my setup. I spent a lot of time reading and comparing before I came up with what I bought.
    Thanks for your help
    Jason
    Last edited by p2ranger (2015-02-13 23:52:29)

  • IMac with 10.4.8 hangs on boot

    My wife runs a non-profit parenting organization using an iMac (700 MHz, G4, flat panel) with OS 10.4.8. Last Friday on startup, it hung within a few seconds of starting to startup. Kernel panic text covered the screen. Retry to startup gave same result. But will start and run ok in Safe Boot mode although the bootup take very, very long --and can't use search to find files and can't print --maybe other limitations with Safe Boot mode will showup. This past weekend, while running in Safe Boot mode, I was able to backup all of her files onto 8 CDs. I could just reinstall everything beginning with the OS and continue through the various applications (MSOffice, Appleworks, Photoshop Elements, etc.) but I would like to find something that wasn't so drastic to try first. Also I would like to have some idea of what happened so that this would not (hopefully) re-occur. Note --no new software or hardware has been installed in many months except for every Apple update that comes along. It does not have an AirPort card and can access the Internet using ethernet and a DSL connection. Since it started into Safe Boot, I understand that some level of disk repair has taken place. What things should I try before I wipe and reinstall?
    iMac G4 700 MHz Flat Screen   Mac OS X (10.4.8)  

    Hello --
    Thanks for the suggestions. I repaired the disk. I repaired the permissions. And I ran the Apple Hardware Test Disk. The disk was fine. Many, many permissions were repaired. And the Hardware Test Disk found nothing. But, at that point, the "Hang on Boot kernel panic" continued. I then went to the suggestions in Dr. Smokes "Resolving Kernel Panics" article. Using "Cocktail" to flush the caches did the trick. The computer is booting fine again and running faster that before. As an added plus, several other annoying problems and issues have gone away. It seems clear to me that there was a problem in one or more of the caches (I have no clue as to which one) and, therefore, very early in the boot sequence, bad data was drawn upon or an attempt to find data was not possible because of damage to one of the caches. At any rate, Thank you for the suggestions --the computer is fine. (And my wife, on behalf of her non-profit parenting support program, sends you many thanks as well. She also swears that she will now carefully backup her files AT LEAST once a week.)

  • Ultra 5 Hangs During Boot

    My Ultra 5 hangs during boot at the following point....
    setting default ipv4 interface......
    I have tried resetting my router, unplugging the network cable, and nothing seems to work.
    John

    jmorrissey3, is this a system that just suddenly stopped working, or is this a "new" system (it's not like Ultra 5s are really new) that you're trying to bring up?
    If this is a new system for you to tinker with, you should just go ahead and reinstall the operating system. This will blow everything away, of course, but it's good experience if you've never done it before and it will guarantee that the system is clean.
    If the data on there must be retained, you can boot from CD-ROM, mount the / partition, and look at some of the configuration files to try to isolate the problem. I would agree that it either is set up for DHCP and there is no DHCP server or there is an invalid NFS mount that is trying to take place.

  • Mac hangs at boot. Please help.

    Hello,
    I have been using an iMac (Mid 2007) for almost a year without any problem. Two weeks ago i star having this problem. I was using the Mac when i notice that it was very slow and that the keychain don't work (with Mail or System preferences for example) so i reboot, then it hangs at boot and constantly keep rebooting.
    For solving the problem i try to check and repair the disk but the disk utility didnt find any problem. So i decide to check and repair the permissions, there were a lot of bad permissions, and i repair them but when i reboot i hangs and keep rebooting like before.
    Before the problem i had made a backup of my system with SuperDuper! so i restore that backup to the drive and i could boot, and all works great for 2 days, then the same problem happens again. I had tried to restore the backup to differents partitions and drives, to check out a hardware problem, but the problem happens again with differents partitions and drives. This problem had happens 7 times in two weeks.
    The only thing that i remember that change in my system two weeks ago is that i install Intego VirusBarrier X5, before that i was using Norton AntiVirus 11.
    I would appreciate a lot any help that you could give me. I am really lost with this problem.
    Thanks,
    Marcelo

    If you just dragged Norton Anti-Virus application from the trash you didn't fully remove the application. There's lots more to be removed. The CD has an uninstaller program you must use. You may find this site useful. At least until you've resolved your problems you might want to consider removing Intego's anti-virus program. It too should have an uninstaller.
    My opinion of both companies is very low. They both use scare tactics to coerce users to buy and use their programs. At present there are no Mac malware in the wild - the sole exception being a trojan horse. Avoiding **** sites and ignoring their attempts to get you to download programs to view their wares should keep you safe from that little critter.

  • Windows XP hangs on boot, computer heats up

    Hi,
    I recently had my Nvidia card replaced in my Mac Book Pro, OSX 10.4.11 and since then tried to boot up Windows XP with Bootcamp. Windows XP hangs on booting and the computer heats up incredibly quickly. Does anyone know why I can't boot in Windows or how to fix this? The mac partition works fine and I can access my documents etc from windows through the mac side. But I do need to run certain programs on Windows. Any help is appreciated.

    Hi and welcome to Discussions,
    first thing I would try are the Safe Boot Options of XP described here http://support.microsoft.com/?scid=kb%3Ben-us%3B315222&x=10&y=11 and especially the 'enable VGA' option to ensure that XP is okay.
    While in Safe Boot maybe deinstalling the Nvidia graphics driver currently installed can help.
    Might be that because of the replacement, the new one isn't correctly detected.
    Hope it helps
    Stefan

  • [Solved] Laptop hangs at boot.

    Hi,
    Since today, my laptop hangs at boot (after I input my password for disk encryption). If I boot without 'quiet' the last message is "Started LVM2 PV scan on device 254:0" as well as some messages about Bluetooth. After these, simply nothing happens.
    The last change I made to my system before this problem started to occur was to patch xf86-input-synaptics with this patch for palm detection: https://gist.github.com/silverhammermba … caa63c86f1 I'm not sure if this is related, but I can't think of anything else I changed.
    Is there a way I can at least get a shell so I can view dmesg output or try to revert to the default synaptics driver?
    Regards,
    wo0p
    Last edited by wo0p (2015-06-19 21:06:53)

    Thanks, I managed to get to a shell using CTRL + ALT + F2. I was certain I tried that, but I might have been hitting CTRL + ALT + 2 the whole time, quite embarrassing...
    Can I just revert to the repository version of xf86-input-synaptics by removing it with pacman -R and then reinstalling with pacman -S ? If so, this doesn't fix my problem.
    I looked through dmesg and the journal but couldn't see any errors. Is there something I missed?
    EDIT: Thanks for the help, I think the problem was that installing the package had created a config (with .pacnew) in the /etc/X11/xorg.conf.d/ directory which caused the problems.
    I would still like to know if I can revert to the repository version of a package in the way I outlined above though.
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 4.0.5-1-ARCH (builduser@tobias) (gcc version 5.1.0 (GCC) ) #1 SMP PREEMPT Sat Jun 6 18:37:49 CEST 2015
    [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=abe988d4-2da5-481b-a713-939e77dfb317 rw cryptdevice=/dev/sda3:luks:allow-discards quiet i915.enable_execlists=0
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000057fff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000000058000-0x0000000000058fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000059000-0x000000000009dfff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c71d9fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000c71da000-0x00000000c7541fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000c7542000-0x00000000caa82fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000caa83000-0x00000000caae1fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000caae2000-0x00000000cb2e3fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000cb2e4000-0x00000000cc46bfff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000cc46c000-0x00000000ccee4fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ccee5000-0x00000000ccffefff] type 20
    [ 0.000000] BIOS-e820: [mem 0x00000000ccfff000-0x00000000ccffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000cd800000-0x00000000cfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022effffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] efi: EFI v2.40 by American Megatrends
    [ 0.000000] efi: ACPI=0xcb6e8000 ACPI 2.0=0xcb6e8000 SMBIOS=0xcce2d998
    [ 0.000000] efi: mem00: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000000000-0x0000000000058000) (0MB)
    [ 0.000000] efi: mem01: [Reserved | | | | | |WB|WT|WC|UC] range=[0x0000000000058000-0x0000000000059000) (0MB)
    [ 0.000000] efi: mem02: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000059000-0x000000000009e000) (0MB)
    [ 0.000000] efi: mem03: [Reserved | | | | | |WB|WT|WC|UC] range=[0x000000000009e000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem04: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x0000000000100000-0x0000000000f29000) (14MB)
    [ 0.000000] efi: mem05: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000000f29000-0x0000000010000000) (240MB)
    [ 0.000000] efi: mem06: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x0000000010000000-0x000000001000b000) (0MB)
    [ 0.000000] efi: mem07: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x000000001000b000-0x000000003675a000) (615MB)
    [ 0.000000] efi: mem08: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000003675a000-0x00000000373a5000) (12MB)
    [ 0.000000] efi: mem09: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000373a5000-0x000000008da14000) (1382MB)
    [ 0.000000] efi: mem10: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x000000008da14000-0x00000000bf558000) (795MB)
    [ 0.000000] efi: mem11: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000bf558000-0x00000000bf598000) (0MB)
    [ 0.000000] efi: mem12: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000bf598000-0x00000000c62f8000) (109MB)
    [ 0.000000] efi: mem13: [Loader Code | | | | | |WB|WT|WC|UC] range=[0x00000000c62f8000-0x00000000c6316000) (0MB)
    [ 0.000000] efi: mem14: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000c6316000-0x00000000c71da000) (14MB)
    [ 0.000000] efi: mem15: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x00000000c71da000-0x00000000c7542000) (3MB)
    [ 0.000000] efi: mem16: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000c7542000-0x00000000c7548000) (0MB)
    [ 0.000000] efi: mem17: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000c7548000-0x00000000c8419000) (14MB)
    [ 0.000000] efi: mem18: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000c8419000-0x00000000ca483000) (32MB)
    [ 0.000000] efi: mem19: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000ca483000-0x00000000ca7de000) (3MB)
    [ 0.000000] efi: mem20: [Boot Code | | | | | |WB|WT|WC|UC] range=[0x00000000ca7de000-0x00000000caa83000) (2MB)
    [ 0.000000] efi: mem21: [Reserved | | | | | |WB|WT|WC|UC] range=[0x00000000caa83000-0x00000000caae2000) (0MB)
    [ 0.000000] efi: mem22: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x00000000caae2000-0x00000000cb2da000) (7MB)
    [ 0.000000] efi: mem23: [Loader Data | | | | | |WB|WT|WC|UC] range=[0x00000000cb2da000-0x00000000cb2e4000) (0MB)
    [ 0.000000] efi: mem24: [ACPI Memory NVS | | | | | |WB|WT|WC|UC] range=[0x00000000cb2e4000-0x00000000cc46c000) (17MB)
    [ 0.000000] efi: mem25: [Runtime Data |RUN| | | | |WB|WT|WC|UC] range=[0x00000000cc46c000-0x00000000ccee5000) (10MB)
    [ 0.000000] efi: mem26: [Runtime Code |RUN| | | | |WB|WT|WC|UC] range=[0x00000000ccee5000-0x00000000ccfff000) (1MB)
    [ 0.000000] efi: mem27: [Boot Data | | | | | |WB|WT|WC|UC] range=[0x00000000ccfff000-0x00000000cd000000) (0MB)
    [ 0.000000] efi: mem28: [Conventional Memory| | | | | |WB|WT|WC|UC] range=[0x0000000100000000-0x000000022f000000) (4848MB)
    [ 0.000000] efi: mem29: [Reserved | | | | | | | | | ] range=[0x00000000cd800000-0x00000000d0000000) (40MB)
    [ 0.000000] efi: mem30: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000f8000000-0x00000000fc000000) (64MB)
    [ 0.000000] efi: mem31: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fec00000-0x00000000fec01000) (0MB)
    [ 0.000000] efi: mem32: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed00000-0x00000000fed04000) (0MB)
    [ 0.000000] efi: mem33: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
    [ 0.000000] efi: mem34: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000fee00000-0x00000000fee01000) (0MB)
    [ 0.000000] efi: mem35: [Memory Mapped I/O |RUN| | | | | | | |UC] range=[0x00000000ff000000-0x0000000100000000) (16MB)
    [ 0.000000] SMBIOS 2.8 present.
    [ 0.000000] DMI: ASUSTeK COMPUTER INC. UX303LNB/UX303LNB, BIOS UX303LNB.203 12/10/2014
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x22f000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-DFFFF uncachable
    [ 0.000000] E0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0000000000 mask 7F80000000 write-back
    [ 0.000000] 1 base 0080000000 mask 7FC0000000 write-back
    [ 0.000000] 2 base 00C0000000 mask 7FF8000000 write-back
    [ 0.000000] 3 base 00C8000000 mask 7FFC000000 write-back
    [ 0.000000] 4 base 00CC000000 mask 7FFF000000 write-back
    [ 0.000000] 5 base 0100000000 mask 7F00000000 write-back
    [ 0.000000] 6 base 0200000000 mask 7FC0000000 write-back
    [ 0.000000] 7 base 0230000000 mask 7FF0000000 uncachable
    [ 0.000000] 8 base 022F000000 mask 7FFF000000 uncachable
    [ 0.000000] 9 disabled
    [ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
    [ 0.000000] e820: update [mem 0xcd000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xcd000 max_arch_pfn = 0x400000000
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
    [ 0.000000] Using GB pages for direct mapping
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b1d000, 0x01b1dfff] PGTABLE
    [ 0.000000] BRK [0x01b1e000, 0x01b1efff] PGTABLE
    [ 0.000000] BRK [0x01b1f000, 0x01b1ffff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x22ee00000-0x22effffff]
    [ 0.000000] [mem 0x22ee00000-0x22effffff] page 2M
    [ 0.000000] BRK [0x01b20000, 0x01b20fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x220000000-0x22edfffff]
    [ 0.000000] [mem 0x220000000-0x22edfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x200000000-0x21fffffff]
    [ 0.000000] [mem 0x200000000-0x21fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0xc71d9fff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
    [ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
    [ 0.000000] [mem 0xc0000000-0xc6ffffff] page 2M
    [ 0.000000] [mem 0xc7000000-0xc71d9fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xc7542000-0xcaa82fff]
    [ 0.000000] [mem 0xc7542000-0xc75fffff] page 4k
    [ 0.000000] [mem 0xc7600000-0xca9fffff] page 2M
    [ 0.000000] [mem 0xcaa00000-0xcaa82fff] page 4k
    [ 0.000000] BRK [0x01b21000, 0x01b21fff] PGTABLE
    [ 0.000000] BRK [0x01b22000, 0x01b22fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0xcaae2000-0xcb2e3fff]
    [ 0.000000] [mem 0xcaae2000-0xcabfffff] page 4k
    [ 0.000000] [mem 0xcac00000-0xcb1fffff] page 2M
    [ 0.000000] [mem 0xcb200000-0xcb2e3fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xccfff000-0xccffffff]
    [ 0.000000] [mem 0xccfff000-0xccffffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x1ffffffff]
    [ 0.000000] [mem 0x100000000-0x1ffffffff] page 1G
    [ 0.000000] RAMDISK: [mem 0x3675a000-0x373a4fff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x00000000CB6E8000 000024 (v02 _ASUS_)
    [ 0.000000] ACPI: XSDT 0x00000000CB6E80B0 0000DC (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: FACP 0x00000000CB701590 00010C (v05 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: DSDT 0x00000000CB6E8218 019372 (v02 _ASUS_ Notebook 01072009 INTL 20120913)
    [ 0.000000] ACPI: FACS 0x00000000CC469F80 000040
    [ 0.000000] ACPI: APIC 0x00000000CB7016A0 000084 (v03 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: FPDT 0x00000000CB701728 000044 (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: FIDT 0x00000000CB701770 00009C (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: ECDT 0x00000000CB701810 0000C1 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
    [ 0.000000] ACPI: MCFG 0x00000000CB7018D8 00003C (v01 _ASUS_ Notebook 01072009 MSFT 00000097)
    [ 0.000000] ACPI: HPET 0x00000000CB701918 000038 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
    [ 0.000000] ACPI: SSDT 0x00000000CB701950 000315 (v01 SataRe SataTabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: UEFI 0x00000000CB701C68 000042 (v01 00000000 00000000)
    [ 0.000000] ACPI: SSDT 0x00000000CB701CB0 000C7D (v02 Ther_R Ther_Rvp 00001000 INTL 20120913)
    [ 0.000000] ACPI: ASF! 0x00000000CB702930 0000A0 (v32 INTEL HCG 00000001 TFSM 000F4240)
    [ 0.000000] ACPI: SSDT 0x00000000CB7029D0 000539 (v02 PmRef Cpu0Ist 00003000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB702F10 000B74 (v02 CpuRef CpuSsdt 00003000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB703A88 003245 (v02 DptfTa DptfTabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB706CD0 000394 (v02 CppcTa CppcTabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: PCCT 0x00000000CB707068 00006E (v05 PcctTa PcctTabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB7070D8 000AC4 (v02 Cpc_Ta Cpc_Tabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB707BA0 006622 (v02 SaSsdt SaSsdt 00003000 INTL 20120913)
    [ 0.000000] ACPI: SSDT 0x00000000CB70E1C8 0006CE (v02 SgRef SgPch 00001000 INTL 20120913)
    [ 0.000000] ACPI: DMAR 0x00000000CB70E898 0000A8 (v01 INTEL BDW 00000001 INTL 00000001)
    [ 0.000000] ACPI: BGRT 0x00000000CB70E940 000038 (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: SSDT 0x00000000CB70E978 001914 (v01 OptRef OptTabl 00001000 INTL 20120913)
    [ 0.000000] ACPI: MSDM 0x00000000CAAE0E18 000055 (v03 _ASUS_ Notebook 00000000 ASUS 00000001)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000022effffff]
    [ 0.000000] NODE_DATA(0) allocated [mem 0x22eff8000-0x22effbfff]
    [ 0.000000] [ffffea0000000000-ffffea0008bfffff] PMD -> [ffff880226600000-ffff88022e5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
    [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
    [ 0.000000] Normal [mem 0x0000000100000000-0x000000022effffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000057fff]
    [ 0.000000] node 0: [mem 0x0000000000059000-0x000000000009dfff]
    [ 0.000000] node 0: [mem 0x0000000000100000-0x00000000c71d9fff]
    [ 0.000000] node 0: [mem 0x00000000c7542000-0x00000000caa82fff]
    [ 0.000000] node 0: [mem 0x00000000caae2000-0x00000000cb2e3fff]
    [ 0.000000] node 0: [mem 0x00000000ccfff000-0x00000000ccffffff]
    [ 0.000000] node 0: [mem 0x0000000100000000-0x000000022effffff]
    [ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000022effffff]
    [ 0.000000] On node 0 totalpages: 2072250
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 22 pages reserved
    [ 0.000000] DMA zone: 3996 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 12925 pages used for memmap
    [ 0.000000] DMA32 zone: 827166 pages, LIFO batch:31
    [ 0.000000] Normal zone: 19392 pages used for memmap
    [ 0.000000] Normal zone: 1241088 pages, LIFO batch:31
    [ 0.000000] Reserving Intel graphics stolen memory at 0xce000000-0xcfffffff
    [ 0.000000] ACPI: PM-Timer IO Port: 0x1808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high res lint[0x24])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] low dfl lint[0x48])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] low res lint[0x49])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] low dfl lint[0x4c])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x00058000-0x00058fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc71da000-0xc7541fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcaa83000-0xcaae1fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcb2e4000-0xcc46bfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcc46c000-0xccee4fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xccee5000-0xccffefff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcd000000-0xcd7fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xcd800000-0xcfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xd0000000-0xf7ffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
    [ 0.000000] e820: [mem 0xd0000000-0xf7ffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 31 pages/cpu @ffff88022ec00000 s86232 r8192 d32552 u524288
    [ 0.000000] pcpu-alloc: s86232 r8192 d32552 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 2039847
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=abe988d4-2da5-481b-a713-939e77dfb317 rw cryptdevice=/dev/sda3:luks:allow-discards quiet i915.enable_execlists=0
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 8015668K/8289000K available (5629K kernel code, 840K rwdata, 1784K rodata, 1160K init, 1152K bss, 273332K reserved, 0K cma-reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    [ 0.000000] NR_IRQS:8448 nr_irqs:728 16
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] spurious 8259A interrupt: IRQ7.
    [ 0.000000] tsc: Detected 2394.256 MHz processor
    [ 0.000023] Calibrating delay loop (skipped), value calculated using timer frequency.. 4790.03 BogoMIPS (lpj=7980853)
    [ 0.000025] pid_max: default: 32768 minimum: 301
    [ 0.000029] ACPI: Core revision 20150204
    [ 0.026322] ACPI: All ACPI Tables successfully acquired
    [ 0.028669] Security Framework initialized
    [ 0.028673] Yama: becoming mindful.
    [ 0.029045] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
    [ 0.030311] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.030856] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.030863] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
    [ 0.031022] Initializing cgroup subsys blkio
    [ 0.031024] Initializing cgroup subsys memory
    [ 0.031029] Initializing cgroup subsys devices
    [ 0.031030] Initializing cgroup subsys freezer
    [ 0.031032] Initializing cgroup subsys net_cls
    [ 0.031051] CPU: Physical Processor ID: 0
    [ 0.031051] CPU: Processor Core ID: 0
    [ 0.031056] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    [ 0.031056] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.031963] mce: CPU supports 7 MCE banks
    [ 0.031974] CPU0: Thermal monitoring enabled (TM1)
    [ 0.032002] process: using mwait in idle threads
    [ 0.032005] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8
    [ 0.032006] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4
    [ 0.032281] Freeing SMP alternatives memory: 20K (ffffffff819f6000 - ffffffff819fb000)
    [ 0.033915] ftrace: allocating 21316 entries in 84 pages
    [ 0.041185] dmar: Host address width 39
    [ 0.041187] dmar: DRHD base: 0x000000fed90000 flags: 0x0
    [ 0.041194] dmar: IOMMU 0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 7e1ff0505e
    [ 0.041195] dmar: DRHD base: 0x000000fed91000 flags: 0x1
    [ 0.041199] dmar: IOMMU 1: reg_base_addr fed91000 ver 1:0 cap d2008c20660462 ecap f010da
    [ 0.041199] dmar: RMRR base: 0x000000cce3e000 end: 0x000000cce4cfff
    [ 0.041200] dmar: RMRR base: 0x000000cd800000 end: 0x000000cfffffff
    [ 0.041202] IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
    [ 0.041203] HPET id 0 under DRHD base 0xfed91000
    [ 0.041484] Your BIOS is broken and requested that x2apic be disabled.
    This will slightly decrease performance.
    Use 'intremap=no_x2apic_optout' to override BIOS request.
    [ 0.041495] Enabled IRQ remapping in xapic mode
    [ 0.041496] x2apic: IRQ remapping doesn't support X2APIC mode
    [ 0.042099] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.075131] TSC deadline timer enabled
    [ 0.075133] smpboot: CPU0: Intel(R) Core(TM) i7-5500U CPU @ 2.40GHz (fam: 06, model: 3d, stepping: 04)
    [ 0.075153] Performance Events: PEBS fmt2+, generic architected perfmon, full-width counters, Intel PMU driver.
    [ 0.075157] ... version: 3
    [ 0.075158] ... bit width: 48
    [ 0.075159] ... generic registers: 4
    [ 0.075159] ... value mask: 0000ffffffffffff
    [ 0.075160] ... max period: 0000ffffffffffff
    [ 0.075161] ... fixed-purpose events: 3
    [ 0.075161] ... event mask: 000000070000000f
    [ 0.095289] x86: Booting SMP configuration:
    [ 0.095291] .... node #0, CPUs: #1
    [ 0.109467] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.116159] #2 #3
    [ 0.150974] x86: Booted up 1 node, 4 CPUs
    [ 0.150977] smpboot: Total of 4 processors activated (19161.13 BogoMIPS)
    [ 0.154621] devtmpfs: initialized
    [ 0.156400] PM: Registering ACPI NVS region [mem 0xcb2e4000-0xcc46bfff] (18382848 bytes)
    [ 0.156672] pinctrl core: initialized pinctrl subsystem
    [ 0.156705] RTC time: 20:30:15, date: 06/19/15
    [ 0.156793] NET: Registered protocol family 16
    [ 0.167829] cpuidle: using governor ladder
    [ 0.181188] cpuidle: using governor menu
    [ 0.181212] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
    [ 0.181214] ACPI: bus type PCI registered
    [ 0.181215] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.181275] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.181277] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.181347] PCI: Using configuration type 1 for base access
    [ 0.194800] ACPI: Added _OSI(Module Device)
    [ 0.194802] ACPI: Added _OSI(Processor Device)
    [ 0.194803] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.194804] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.197821] ACPI : EC: EC description table is found, configuring boot EC
    [ 0.200562] ACPI: Executed 8 blocks of module-level executable AML code
    [ 0.206934] ACPI: Dynamic OEM Table Load:
    [ 0.206939] ACPI: SSDT 0xFFFF880224F79000 0003D3 (v02 PmRef Cpu0Cst 00003001 INTL 20120913)
    [ 0.207792] ACPI: Dynamic OEM Table Load:
    [ 0.207796] ACPI: SSDT 0xFFFF880224EFA000 0005AA (v02 PmRef ApIst 00003000 INTL 20120913)
    [ 0.208691] ACPI: Dynamic OEM Table Load:
    [ 0.208695] ACPI: SSDT 0xFFFF880224F59800 000119 (v02 PmRef ApCst 00003000 INTL 20120913)
    [ 0.210219] ACPI: Interpreter enabled
    [ 0.210227] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150204/hwxface-580)
    [ 0.210234] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150204/hwxface-580)
    [ 0.210245] ACPI: (supports S0 S3 S4 S5)
    [ 0.210246] ACPI: Using IOAPIC for interrupt routing
    [ 0.210268] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.212136] ACPI: Power Resource [PG00] (on)
    [ 0.212420] ACPI: Power Resource [PG01] (on)
    [ 0.212693] ACPI: Power Resource [PG02] (on)
    [ 0.213679] ACPI: Power Resource [PC05] (on)
    [ 0.220550] ACPI: Power Resource [FN00] (off)
    [ 0.220603] ACPI: Power Resource [FN01] (off)
    [ 0.220655] ACPI: Power Resource [FN02] (off)
    [ 0.220707] ACPI: Power Resource [FN03] (off)
    [ 0.220759] ACPI: Power Resource [FN04] (off)
    [ 0.221480] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
    [ 0.221485] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.221893] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
    [ 0.222200] PCI host bridge to bus 0000:00
    [ 0.222202] pci_bus 0000:00: root bus resource [bus 00-3e]
    [ 0.222204] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
    [ 0.222205] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
    [ 0.222206] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
    [ 0.222208] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff window]
    [ 0.222209] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff window]
    [ 0.222210] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff window]
    [ 0.222211] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff window]
    [ 0.222212] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
    [ 0.222213] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
    [ 0.222214] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
    [ 0.222215] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
    [ 0.222216] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfeafffff window]
    [ 0.222222] pci 0000:00:00.0: [8086:1604] type 00 class 0x060000
    [ 0.222300] pci 0000:00:02.0: [8086:1616] type 00 class 0x030000
    [ 0.222309] pci 0000:00:02.0: reg 0x10: [mem 0xf5000000-0xf5ffffff 64bit]
    [ 0.222314] pci 0000:00:02.0: reg 0x18: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.222318] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
    [ 0.222391] pci 0000:00:03.0: [8086:160c] type 00 class 0x040300
    [ 0.222397] pci 0000:00:03.0: reg 0x10: [mem 0xf721c000-0xf721ffff 64bit]
    [ 0.222476] pci 0000:00:04.0: [8086:1603] type 00 class 0x118000
    [ 0.222486] pci 0000:00:04.0: reg 0x10: [mem 0xf7210000-0xf7217fff 64bit]
    [ 0.222580] pci 0000:00:14.0: [8086:9cb1] type 00 class 0x0c0330
    [ 0.222595] pci 0000:00:14.0: reg 0x10: [mem 0xf7200000-0xf720ffff 64bit]
    [ 0.222648] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.222690] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.222719] pci 0000:00:16.0: [8086:9cba] type 00 class 0x078000
    [ 0.222734] pci 0000:00:16.0: reg 0x10: [mem 0xf7224000-0xf722401f 64bit]
    [ 0.222786] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
    [ 0.222854] pci 0000:00:1b.0: [8086:9ca0] type 00 class 0x040300
    [ 0.222869] pci 0000:00:1b.0: reg 0x10: [mem 0xf7218000-0xf721bfff 64bit]
    [ 0.222918] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.222959] pci 0000:00:1b.0: System wakeup disabled by ACPI
    [ 0.222986] pci 0000:00:1c.0: [8086:9c90] type 01 class 0x060400
    [ 0.223048] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.223089] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.223118] pci 0000:00:1c.3: [8086:9c96] type 01 class 0x060400
    [ 0.223184] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.223224] pci 0000:00:1c.3: System wakeup disabled by ACPI
    [ 0.223250] pci 0000:00:1c.4: [8086:9c98] type 01 class 0x060400
    [ 0.223307] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.223348] pci 0000:00:1c.4: System wakeup disabled by ACPI
    [ 0.223382] pci 0000:00:1f.0: [8086:9cc3] type 00 class 0x060100
    [ 0.223542] pci 0000:00:1f.2: [8086:9c83] type 00 class 0x010601
    [ 0.223554] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
    [ 0.223559] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
    [ 0.223565] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
    [ 0.223571] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
    [ 0.223576] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
    [ 0.223582] pci 0000:00:1f.2: reg 0x24: [mem 0xf7222000-0xf72227ff]
    [ 0.223613] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.223670] pci 0000:00:1f.3: [8086:9ca2] type 00 class 0x0c0500
    [ 0.223682] pci 0000:00:1f.3: reg 0x10: [mem 0xf7221000-0xf72210ff 64bit]
    [ 0.223697] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
    [ 0.223776] pci 0000:00:1f.6: [8086:9ca4] type 00 class 0x118000
    [ 0.223805] pci 0000:00:1f.6: reg 0x10: [mem 0xf7220000-0xf7220fff 64bit]
    [ 0.224013] acpiphp: Slot [1] registered
    [ 0.224017] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.224292] pci 0000:02:00.0: [8086:095a] type 00 class 0x028000
    [ 0.224423] pci 0000:02:00.0: reg 0x10: [mem 0xf7100000-0xf7101fff 64bit]
    [ 0.224907] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
    [ 0.231440] pci 0000:00:1c.3: PCI bridge to [bus 02]
    [ 0.231445] pci 0000:00:1c.3: bridge window [mem 0xf7100000-0xf71fffff]
    [ 0.231518] pci 0000:03:00.0: [10de:1341] type 00 class 0x030200
    [ 0.231534] pci 0000:03:00.0: reg 0x10: [mem 0xf6000000-0xf6ffffff]
    [ 0.231547] pci 0000:03:00.0: reg 0x14: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.231561] pci 0000:03:00.0: reg 0x1c: [mem 0xf0000000-0xf1ffffff 64bit pref]
    [ 0.231570] pci 0000:03:00.0: reg 0x24: [io 0xe000-0xe07f]
    [ 0.231579] pci 0000:03:00.0: reg 0x30: [mem 0xf7000000-0xf707ffff pref]
    [ 0.231660] pci 0000:03:00.0: System wakeup disabled by ACPI
    [ 0.237972] pci 0000:00:1c.4: PCI bridge to [bus 03]
    [ 0.237975] pci 0000:00:1c.4: bridge window [io 0xe000-0xefff]
    [ 0.237977] pci 0000:00:1c.4: bridge window [mem 0xf6000000-0xf70fffff]
    [ 0.237982] pci 0000:00:1c.4: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
    [ 0.238138] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
    [ 0.239089] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
    [ 0.239130] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239168] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239209] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239247] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239285] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239323] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239360] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.239770] ACPI: Enabled 4 GPEs in block 00 to 7F
    [ 0.239827] ACPI : EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
    [ 0.239900] vgaarb: setting as boot device: PCI:0000:00:02.0
    [ 0.239901] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.239903] vgaarb: loaded
    [ 0.239904] vgaarb: bridge control possible 0000:00:02.0
    [ 0.239990] PCI: Using ACPI for IRQ routing
    [ 0.241093] PCI: pci_cache_line_size set to 64 bytes
    [ 0.241127] e820: reserve RAM buffer [mem 0x00058000-0x0005ffff]
    [ 0.241128] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
    [ 0.241129] e820: reserve RAM buffer [mem 0xc71da000-0xc7ffffff]
    [ 0.241129] e820: reserve RAM buffer [mem 0xcaa83000-0xcbffffff]
    [ 0.241130] e820: reserve RAM buffer [mem 0xcb2e4000-0xcbffffff]
    [ 0.241131] e820: reserve RAM buffer [mem 0xcd000000-0xcfffffff]
    [ 0.241132] e820: reserve RAM buffer [mem 0x22f000000-0x22fffffff]
    [ 0.241211] NetLabel: Initializing
    [ 0.241212] NetLabel: domain hash size = 128
    [ 0.241213] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.241222] NetLabel: unlabeled traffic allowed by default
    [ 0.241240] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
    [ 0.241244] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
    [ 0.243265] Switched to clocksource hpet
    [ 0.246853] pnp: PnP ACPI init
    [ 0.246992] system 00:00: [io 0x0240-0x0259] has been reserved
    [ 0.246995] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.247057] pnp 00:01: Plug and Play ACPI device, IDs FLT0102 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
    [ 0.247087] pnp 00:02: Plug and Play ACPI device, IDs ATK3001 PNP030b (active)
    [ 0.247149] system 00:03: [io 0x0680-0x069f] has been reserved
    [ 0.247151] system 00:03: [io 0xffff] has been reserved
    [ 0.247153] system 00:03: [io 0xffff] has been reserved
    [ 0.247154] system 00:03: [io 0xffff] has been reserved
    [ 0.247155] system 00:03: [io 0x1800-0x18fe] could not be reserved
    [ 0.247156] system 00:03: [io 0x164e-0x164f] has been reserved
    [ 0.247158] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.247192] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.247218] system 00:05: [io 0x1854-0x1857] has been reserved
    [ 0.247220] system 00:05: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
    [ 0.247329] system 00:06: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.247330] system 00:06: [mem 0xfed10000-0xfed17fff] has been reserved
    [ 0.247332] system 00:06: [mem 0xfed18000-0xfed18fff] has been reserved
    [ 0.247334] system 00:06: [mem 0xfed19000-0xfed19fff] has been reserved
    [ 0.247335] system 00:06: [mem 0xf8000000-0xfbffffff] has been reserved
    [ 0.247336] system 00:06: [mem 0xfed20000-0xfed3ffff] has been reserved
    [ 0.247338] system 00:06: [mem 0xfed90000-0xfed93fff] could not be reserved
    [ 0.247339] system 00:06: [mem 0xfed45000-0xfed8ffff] has been reserved
    [ 0.247340] system 00:06: [mem 0xff000000-0xffffffff] has been reserved
    [ 0.247341] system 00:06: [mem 0xfee00000-0xfeefffff] could not be reserved
    [ 0.247343] system 00:06: [mem 0xf7fe0000-0xf7feffff] has been reserved
    [ 0.247344] system 00:06: [mem 0xf7ff0000-0xf7ffffff] has been reserved
    [ 0.247346] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.247731] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.248169] pnp: PnP ACPI: found 8 devices
    [ 0.253940] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.253949] pci 0000:00:1c.3: PCI bridge to [bus 02]
    [ 0.253952] pci 0000:00:1c.3: bridge window [mem 0xf7100000-0xf71fffff]
    [ 0.253958] pci 0000:00:1c.4: PCI bridge to [bus 03]
    [ 0.253960] pci 0000:00:1c.4: bridge window [io 0xe000-0xefff]
    [ 0.253963] pci 0000:00:1c.4: bridge window [mem 0xf6000000-0xf70fffff]
    [ 0.253966] pci 0000:00:1c.4: bridge window [mem 0xe0000000-0xf1ffffff 64bit pref]
    [ 0.253970] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
    [ 0.253972] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
    [ 0.253973] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
    [ 0.253974] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff window]
    [ 0.253975] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff window]
    [ 0.253976] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff window]
    [ 0.253977] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff window]
    [ 0.253979] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff window]
    [ 0.253980] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff window]
    [ 0.253981] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff window]
    [ 0.253982] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff window]
    [ 0.253983] pci_bus 0000:00: resource 15 [mem 0xd0000000-0xfeafffff window]
    [ 0.253984] pci_bus 0000:02: resource 1 [mem 0xf7100000-0xf71fffff]
    [ 0.253986] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
    [ 0.253987] pci_bus 0000:03: resource 1 [mem 0xf6000000-0xf70fffff]
    [ 0.253988] pci_bus 0000:03: resource 2 [mem 0xe0000000-0xf1ffffff 64bit pref]
    [ 0.254009] NET: Registered protocol family 2
    [ 0.254153] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.254258] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    [ 0.254368] TCP: Hash tables configured (established 65536 bind 65536)
    [ 0.254382] TCP: reno registered
    [ 0.254390] UDP hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.254411] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
    [ 0.254449] NET: Registered protocol family 1
    [ 0.254459] pci 0000:00:02.0: Video device with shadowed ROM
    [ 0.254627] PCI: CLS 64 bytes, default 64
    [ 0.254658] Unpacking initramfs...
    [ 0.419468] Freeing initrd memory: 12588K (ffff88003675a000 - ffff8800373a5000)
    [ 0.419489] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 0.419492] software IO TLB [mem 0xc2316000-0xc6316000] (64MB) mapped at [ffff8800c2316000-ffff8800c6315fff]
    [ 0.419632] RAPL PMU detected, hw unit 2^-14 Joules, API unit is 2^-32 Joules, 4 fixed counters 655360 ms ovfl timer
    [ 0.419670] microcode: CPU0 sig=0x306d4, pf=0x40, revision=0x13
    [ 0.419675] microcode: CPU1 sig=0x306d4, pf=0x40, revision=0x13
    [ 0.419681] microcode: CPU2 sig=0x306d4, pf=0x40, revision=0x13
    [ 0.419686] microcode: CPU3 sig=0x306d4, pf=0x40, revision=0x13
    [ 0.419721] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 0.419738] Scanning for low memory corruption every 60 seconds
    [ 0.419899] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 0.419912] Initialise system trusted keyring
    [ 0.420141] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.421107] zpool: loaded
    [ 0.421109] zbud: loaded
    [ 0.421228] VFS: Disk quotas dquot_6.5.2
    [ 0.421250] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.421369] Key type big_key registered
    [ 0.421511] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.421537] io scheduler noop registered
    [ 0.421539] io scheduler deadline registered
    [ 0.421558] io scheduler cfq registered (default)
    [ 0.421962] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
    [ 0.421965] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
    [ 0.421974] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
    [ 0.421975] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
    [ 0.421977] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
    [ 0.421986] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
    [ 0.421987] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
    [ 0.421990] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
    [ 0.421994] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.422004] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.422016] efifb: probing for efifb
    [ 0.422032] efifb: framebuffer at 0xd0000000, mapped to 0xffffc90004f00000, using 8128k, total 8128k
    [ 0.422033] efifb: mode is 1920x1080x32, linelength=7680, pages=1
    [ 0.422034] efifb: scrolling: redraw
    [ 0.422035] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.425476] Console: switching to colour frame buffer device 240x67
    [ 0.429197] fb0: EFI VGA frame buffer device
    [ 0.429204] intel_idle: MWAIT substates: 0x11142120
    [ 0.429205] intel_idle: v0.4 model 0x3D
    [ 0.429205] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 0.429389] GHES: HEST is not enabled!
    [ 0.429438] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.429759] Linux agpgart interface v0.103
    [ 0.429798] rtc_cmos 00:04: RTC can wake from S4
    [ 0.429904] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
    [ 0.429928] rtc_cmos 00:04: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
    [ 0.429937] Intel P-state driver initializing.
    [ 0.430057] ledtrig-cpu: registered to indicate activity on CPUs
    [ 0.430573] TCP: cubic registered
    [ 0.430824] NET: Registered protocol family 10
    [ 0.431247] NET: Registered protocol family 17
    [ 0.431931] Loading compiled-in X.509 certificates
    [ 0.431964] registered taskstats version 1
    [ 0.433023] Magic number: 3:29:549
    [ 0.433038] clockevents clockevent0: hash matches
    [ 0.433067] acpi PNP0C0F:00: hash matches
    [ 0.433191] rtc_cmos 00:04: setting system clock to 2015-06-19 20:30:16 UTC (1434745816)
    [ 0.433387] PM: Hibernation image not present or could not be loaded.
    [ 0.434000] Freeing unused kernel memory: 1160K (ffffffff818d4000 - ffffffff819f6000)
    [ 0.434003] Write protecting the kernel read-only data: 8192k
    [ 0.434643] Freeing unused kernel memory: 504K (ffff880001582000 - ffff880001600000)
    [ 0.434865] Freeing unused kernel memory: 264K (ffff8800017be000 - ffff880001800000)
    [ 0.441392] random: systemd-tmpfile urandom read with 1 bits of entropy available
    [ 0.458172] sdhci: Secure Digital Host Controller Interface driver
    [ 0.458174] sdhci: Copyright(c) Pierre Ossman
    [ 0.461368] i8042: PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    [ 0.464831] i8042: Detected active multiplexing controller, rev 1.1
    [ 0.466075] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.466090] serio: i8042 AUX0 port at 0x60,0x64 irq 12
    [ 0.466093] serio: i8042 AUX1 port at 0x60,0x64 irq 12
    [ 0.466095] serio: i8042 AUX2 port at 0x60,0x64 irq 12
    [ 0.466097] serio: i8042 AUX3 port at 0x60,0x64 irq 12
    [ 0.467331] ACPI: bus type USB registered
    [ 0.467357] usbcore: registered new interface driver usbfs
    [ 0.467367] usbcore: registered new interface driver hub
    [ 0.467449] usbcore: registered new device driver usb
    [ 0.467882] SCSI subsystem initialized
    [ 0.469036] libata version 3.00 loaded.
    [ 0.469212] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.469219] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
    [ 0.469295] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
    [ 0.469300] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 0.469567] hub 1-0:1.0: USB hub found
    [ 0.469579] hub 1-0:1.0: 11 ports detected
    [ 0.472290] AVX2 version of gcm_enc/dec engaged.
    [ 0.472292] AES CTR mode by8 optimization enabled
    [ 0.473751] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 0.473755] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
    [ 0.473912] hub 2-0:1.0: USB hub found
    [ 0.473922] hub 2-0:1.0: 4 ports detected
    [ 0.475776] ahci 0000:00:1f.2: version 3.0
    [ 0.486870] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x1 impl SATA mode
    [ 0.486873] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
    [ 0.487298] scsi host0: ahci
    [ 0.487404] scsi host1: ahci
    [ 0.487499] scsi host2: ahci
    [ 0.487602] scsi host3: ahci
    [ 0.487645] ata1: SATA max UDMA/133 abar m2048@0xf7222000 port 0xf7222100 irq 46
    [ 0.487646] ata2: DUMMY
    [ 0.487647] ata3: DUMMY
    [ 0.487648] ata4: DUMMY
    [ 0.518177] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 0.807120] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 0.808148] ata1.00: ATA-9: SanDisk SD7SB3Q256G1002, X2150000, max UDMA/133
    [ 0.808151] ata1.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
    [ 0.809886] ata1.00: configured for UDMA/133
    [ 0.810105] scsi 0:0:0:0: Direct-Access ATA SanDisk SD7SB3Q2 0000 PQ: 0 ANSI: 5
    [ 0.811845] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
    [ 0.811926] sd 0:0:0:0: [sda] Write Protect is off
    [ 0.811929] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 0.811949] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 0.813282] sda: sda1 sda2 sda3
    [ 0.813602] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 0.833270] device-mapper: uevent: version 1.0.3
    [ 0.833364] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: [email protected]
    [ 0.833785] usb 1-5: new high-speed USB device number 2 using xhci_hcd
    [ 1.207444] usb 1-8: new full-speed USB device number 3 using xhci_hcd
    [ 1.381488] usb 1-8: No LPM exit latency info found, disabling LPM.
    [ 1.420941] tsc: Refined TSC clocksource calibration: 2394.457 MHz
    [ 2.422042] Switched to clocksource tsc
    [ 4.601817] NET: Registered protocol family 38
    [ 5.500920] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
    [ 5.557255] systemd[1]: systemd 219 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD +IDN)
    [ 5.557386] systemd[1]: Detected architecture 'x86-64'.
    [ 5.557569] systemd[1]: Set hostname to <WOOP-PLUTO>.
    [ 5.581258] systemd[1]: Unit type .busname is not supported on this system.
    [ 5.609266] systemd[1]: Cannot add dependency job for unit vmware-USBArbitrator.service, ignoring: Unit vmware-USBArbitrator.service failed to load: No such file or directory.
    [ 5.609648] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 5.609656] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 5.609676] systemd[1]: Reached target Login Prompts.
    [ 5.609681] systemd[1]: Starting Login Prompts.
    [ 5.609691] systemd[1]: Reached target Remote File Systems.
    [ 5.609695] systemd[1]: Starting Remote File Systems.
    [ 5.609816] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 5.609824] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
    [ 5.609831] systemd[1]: Reached target Encrypted Volumes.
    [ 5.609836] systemd[1]: Starting Encrypted Volumes.
    [ 5.610016] systemd[1]: Created slice Root Slice.
    [ 5.610022] systemd[1]: Starting Root Slice.
    [ 5.610045] systemd[1]: Listening on udev Control Socket.
    [ 5.610051] systemd[1]: Starting udev Control Socket.
    [ 5.610064] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 5.610069] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 5.610116] systemd[1]: Created slice User and Session Slice.
    [ 5.610121] systemd[1]: Starting User and Session Slice.
    [ 5.610163] systemd[1]: Created slice System Slice.
    [ 5.610171] systemd[1]: Starting System Slice.
    [ 5.610222] systemd[1]: Created slice system-systemd\x2dfsck.slice.
    [ 5.610228] systemd[1]: Starting system-systemd\x2dfsck.slice.
    [ 5.610271] systemd[1]: Created slice system-rfkill\x2dblock.slice.
    [ 5.610276] systemd[1]: Starting system-rfkill\x2dblock.slice.
    [ 5.610318] systemd[1]: Created slice system-getty.slice.
    [ 5.610323] systemd[1]: Starting system-getty.slice.
    [ 5.610340] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 5.610345] systemd[1]: Starting Delayed Shutdown Socket.
    [ 5.610365] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 5.610370] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 5.612312] random: nonblocking pool is initialized
    [ 5.620499] systemd[1]: Listening on Journal Audit Socket.
    [ 5.620536] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 5.620543] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 5.620550] systemd[1]: Reached target Slices.
    [ 5.620555] systemd[1]: Starting Slices.
    [ 5.620589] systemd[1]: Listening on Journal Socket.
    [ 5.620598] systemd[1]: Starting Journal Socket.
    [ 5.620608] systemd[1]: Started File System Check on Root Device.
    [ 5.620937] systemd[1]: Mounting Debug File System...
    [ 5.621251] systemd[1]: Mounting Huge Pages File System...
    [ 5.621859] systemd[1]: Started Load Kernel Modules.
    [ 5.621874] systemd[1]: Mounted FUSE Control File System.
    [ 5.622224] systemd[1]: Starting Remount Root and Kernel File Systems...
    [ 5.622646] systemd[1]: Starting Apply Kernel Variables...
    [ 5.623622] systemd[1]: Starting Set Up Additional Binary Formats...
    [ 5.623961] systemd[1]: Mounting POSIX Message Queue File System...
    [ 5.624013] systemd[1]: Listening on Journal Socket (/dev/log).
    [ 5.624026] systemd[1]: Starting Journal Socket (/dev/log).
    [ 5.624427] systemd[1]: Starting Journal Service...
    [ 5.624747] systemd[1]: Mounting Configuration File System...
    [ 5.625120] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 5.625185] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 5.625194] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 5.625202] systemd[1]: Reached target Paths.
    [ 5.625207] systemd[1]: Starting Paths.
    [ 5.625476] systemd[1]: Starting Setup Virtual Console...
    [ 5.625513] systemd[1]: Listening on udev Kernel Socket.
    [ 5.625525] systemd[1]: Starting udev Kernel Socket.
    [ 5.625917] systemd[1]: Starting udev Coldplug all Devices...
    [ 5.626783] systemd[1]: Started Create list of required static device nodes for the current kernel.
    [ 5.626862] systemd[1]: Got automount request for /proc/sys/fs/binfmt_misc, triggered by 214 (systemd-binfmt)
    [ 5.627145] systemd[1]: Mounting Arbitrary Executable File Formats File System...
    [ 5.631100] systemd[1]: Started Setup Virtual Console.
    [ 5.637366] systemd[1]: Started Apply Kernel Variables.
    [ 5.638348] systemd[1]: Mounted Huge Pages File System.
    [ 5.638376] systemd[1]: Mounted POSIX Message Queue File System.
    [ 5.638392] systemd[1]: Mounted Configuration File System.
    [ 5.639302] EXT4-fs (dm-2): re-mounted. Opts: data=ordered
    [ 5.639530] systemd-journald[216]: Failed to set file attributes: Inappropriate ioctl for device
    [ 5.640253] systemd[1]: Mounted Arbitrary Executable File Formats File System.
    [ 5.640287] systemd[1]: Mounted Debug File System.
    [ 5.642518] systemd[1]: Started Remount Root and Kernel File Systems.
    [ 5.642721] systemd[1]: Started Set Up Additional Binary Formats.
    [ 5.642901] systemd[1]: Started udev Coldplug all Devices.
    [ 5.650745] systemd[1]: Starting Load/Save Random Seed...
    [ 5.650775] systemd[1]: Started Rebuild Dynamic Linker Cache.
    [ 5.651626] systemd[1]: Started Rebuild Hardware Database.
    [ 5.651645] systemd[1]: Started First Boot Wizard.
    [ 5.651659] systemd[1]: Started Create System Users.
    [ 5.651982] systemd[1]: Starting Create Static Device Nodes in /dev...
    [ 5.655137] systemd[1]: Started Load/Save Random Seed.
    [ 5.673398] systemd[1]: Started Create Static Device Nodes in /dev.
    [ 5.673906] systemd[1]: Starting udev Kernel Device Manager...
    [ 5.673930] systemd[1]: Reached target Local File Systems (Pre).
    [ 5.673941] systemd[1]: Starting Local File Systems (Pre).
    [ 5.674530] systemd[1]: Mounting /tmp...
    [ 5.676222] systemd[1]: Mounted /tmp.
    [ 5.714702] systemd[1]: Started udev Kernel Device Manager.
    [ 5.731901] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input5
    [ 5.732762] ACPI: Lid Switch [LID]
    [ 5.732815] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input6
    [ 5.732819] ACPI: Sleep Button [SLPB]
    [ 5.732867] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
    [ 5.732870] ACPI: Power Button [PWRF]
    [ 5.735236] systemd[1]: Started Journal Service.
    [ 5.739454] ACPI: AC Adapter [AC0] (off-line)
    [ 5.740472] systemd-journald[216]: Received request to flush runtime journal from PID 1
    [ 5.741401] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 5.791768] [drm] Initialized drm 1.1.0 20060810
    [ 5.797640] ACPI: Battery Slot [BAT0] (battery present)
    [ 5.797836] wmi: Mapper loaded
    [ 5.824171] hidraw: raw HID events driver (C) Jiri Kosina
    [ 5.845805] sound hdaudioC1D0: CX20751/2: BIOS auto-probing.
    [ 5.846099] sound hdaudioC1D0: autoconfig for CX20751/2: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
    [ 5.846103] sound hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 5.846105] sound hdaudioC1D0: hp_outs=1 (0x16/0x0/0x0/0x0/0x0)
    [ 5.846107] sound hdaudioC1D0: mono: mono_out=0x0
    [ 5.846108] sound hdaudioC1D0: inputs:
    [ 5.846111] sound hdaudioC1D0: Internal Mic=0x1a
    [ 5.846113] sound hdaudioC1D0: Mic=0x19
    [ 5.846718] sound hdaudioC1D0: Enable sync_write for stable communication
    [ 5.846766] [drm] Memory usable by graphics device = 4096M
    [ 5.846770] checking generic (d0000000 7f0000) vs hw (d0000000 10000000)
    [ 5.846773] fb: switching to inteldrmfb from EFI VGA
    [ 5.846791] Console: switching to colour dummy device 80x25
    [ 5.846944] [drm] Replacing VGA console driver
    [ 5.849342] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/sound/card1/hdaudioC1D0/input8
    [ 5.849463] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input9
    [ 5.849490] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
    [ 5.855615] thermal LNXTHERM:00: registered as thermal_zone2
    [ 5.855618] ACPI: Thermal Zone [THRM] (48 C)
    [ 5.858016] thermal LNXTHERM:01: registered as thermal_zone3
    [ 5.858018] ACPI: Thermal Zone [TZ00] (28 C)
    [ 5.858296] thermal LNXTHERM:02: registered as thermal_zone4
    [ 5.858298] ACPI: Thermal Zone [TZ01] (30 C)
    [ 5.858483] cfg80211: Calling CRDA to update world regulatory domain
    [ 5.862994] Bluetooth: Core ver 2.20
    [ 5.863009] NET: Registered protocol family 31
    [ 5.863010] Bluetooth: HCI device and connection manager initialized
    [ 5.863015] Bluetooth: HCI socket layer initialized
    [ 5.863018] Bluetooth: L2CAP socket layer initialized
    [ 5.863024] Bluetooth: SCO socket layer initialized
    [ 5.866422] input: PC Speaker as /devices/platform/pcspkr/input/input11
    [ 5.867516] Intel(R) Wireless WiFi driver for Linux
    [ 5.867518] Copyright(c) 2003- 2014 Intel Corporation
    [ 5.867886] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 5.867888] [drm] Driver supports precise vblank timestamp query.
    [ 5.868042] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 5.870016] usbcore: registered new interface driver btusb
    [ 5.877889] iwlwifi 0000:02:00.0: loaded firmware version 25.17.12.0 op_mode iwlmvm
    [ 5.880266] intel_rapl: Found RAPL domain package
    [ 5.880269] intel_rapl: Found RAPL domain core
    [ 5.880272] intel_rapl: Found RAPL domain uncore
    [ 5.880274] intel_rapl: Found RAPL domain dram
    [ 5.882922] media: Linux media interface: v0.10
    [ 5.884691] Bluetooth: hci0: read Intel version: 370810011002270d00
    [ 5.886215] Bluetooth: hci0: Intel Bluetooth firmware file: intel/ibt-hw-37.8.10-fw-1.10.2.27.d.bseq
    [ 5.918064] Linux video capture interface: v2.00
    [ 5.921474] iTCO_vendor_support: vendor-support=0
    [ 5.922849] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 5.922892] iTCO_wdt: Found a Wildcat Point_LP TCO device (Version=2, TCOBASE=0x1860)
    [ 5.922978] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 5.923412] asus_wmi: ASUS WMI generic driver loaded
    [ 5.930495] fbcon: inteldrmfb (fb0) is primary device
    [ 5.932627] iwlwifi 0000:02:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0x184
    [ 5.933078] iwlwifi 0000:02:00.0: L1 Disabled - LTR Enabled
    [ 5.933238] iwlwifi 0000:02:00.0: L1 Disabled - LTR Enabled
    [ 5.933985] asus_wmi: Initialization: 0x1
    [ 5.934961] asus_wmi: BIOS WMI version: 7.9
    [ 5.935116] asus_wmi: SFUN value: 0xa2077
    [ 5.936702] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
    [ 5.937631] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 5.937749] Adding 8388604k swap on /dev/mapper/vg0-swap. Priority:-1 extents:1 across:8388604k SSFS
    [ 5.938748] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null)
    [ 5.941016] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input16
    [ 5.943447] uvcvideo: Found UVC 1.00 device USB2.0 UVC HD Webcam (064e:9700)
    [ 5.945744] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input17
    [ 5.945833] ACPI Exception: AE_NOT_FOUND, Evaluating _DOD (20150204/video-1257)
    [ 5.945834] ACPI: Video Device [PEGP] (multi-head: no rom: yes post: no)
    [ 5.945879] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:22/LNXVIDEO:01/input/input18
    [ 5.945995] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
    [ 5.945999] [drm] Initialized i915 1.6.0 20150130 for 0000:00:02.0 on minor 0
    [ 5.946115] ACPI Warning: SystemIO range 0x000000000000F040-0x000000000000F05F conflicts with OpRegion 0x000000000000F040-0x000000000000F04F (\SMB0) (20150204/utaddress-254)
    [ 5.946120] ACPI Warning: SystemIO range 0x000000000000F040-0x000000000000F05F conflicts with OpRegion 0x000000000000F040-0x000000000000F04F (\_SB_.PCI0.SBUS.SMBI) (20150204/utaddress-254)
    [ 5.946121] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 5.949372] input: USB2.0 UVC HD Webcam as /devices/pci0000:00/0000:00:14.0/usb1/1-5/1-5:1.0/input/input19
    [ 5.949434] usbcore: registered new interface driver uvcvideo
    [ 5.949435] USB Video Class driver (1.1.1)
    [ 6.030252] usb 1-8: USB disconnect, device number 3
    [ 6.030362] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-19)
    [ 6.030393] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input20
    [ 6.030780] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input21
    [ 6.030895] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input22
    [ 6.030945] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
    [ 6.031170] asus_wmi: Backlight controlled by ACPI video driver
    [ 6.032320] ieee80211 phy0: Selected rate control algorithm 'iwl-mvm-rs'
    [ 6.036491] iwlwifi 0000:02:00.0 wlp2s0: renamed from wlan0
    [ 6.054693] input: FocalTechPS/2 FocalTech FocalTech Touchpad as /devices/platform/i8042/serio4/input/input15
    [ 6.056212] mousedev: PS/2 mouse device common for all mice
    [ 6.497765] bbswitch: version 0.8
    [ 6.497769] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
    [ 6.497773] bbswitch: Found discrete VGA device 0000:03:00.0: \_SB_.PCI0.RP05.PEGP
    [ 6.497783] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
    [ 6.497854] bbswitch: detected an Optimus _DSM function
    [ 6.497904] bbswitch: Succesfully loaded. Discrete card 0000:03:00.0 is on
    [ 6.499057] bbswitch: disabling discrete graphics
    [ 6.499065] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20150204/nsarguments-95)
    [ 6.794166] /dev/vmmon[384]: Module vmmon: registered with major=10 minor=165
    [ 6.794169] /dev/vmmon[384]: Module vmmon: initialized
    [ 6.816392] Guest personality initialized and is inactive
    [ 6.816436] VMCI host device registered (name=vmci, major=10, minor=56)
    [ 6.816437] Initialized host personality
    [ 6.847875] NET: Registered protocol family 40
    [ 6.870900] fuse init (API version 7.23)
    [ 6.898024] ppdev: user-space parallel port driver
    [ 7.106012] Console: switching to colour frame buffer device 240x67
    [ 7.110124] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 7.110125] i915 0000:00:02.0: registered panic notifier
    [ 7.148418] iwlwifi 0000:02:00.0: L1 Disabled - LTR Enabled
    [ 7.148675] iwlwifi 0000:02:00.0: L1 Disabled - LTR Enabled
    [ 7.159323] /dev/vmnet: open called by PID 505 (vmnet-bridge)
    [ 7.159334] /dev/vmnet: hub 0 does not exist, allocating memory.
    [ 7.159355] /dev/vmnet: port on hub 0 successfully opened
    [ 7.159363] bridge-wlp2s0: device is wireless, enabling SMAC
    [ 7.159366] bridge-wlp2s0: up
    [ 7.159370] bridge-wlp2s0: attached
    [ 7.161385] bridge-wlp2s0: disabling the bridge
    [ 7.172268] bridge-wlp2s0: down
    [ 7.172274] bridge-wlp2s0: detached
    [ 7.549177] cfg80211: Calling CRDA to update world regulatory domain
    [ 7.631166] /dev/vmnet: open called by PID 526 (vmnet-netifup)
    [ 7.631172] /dev/vmnet: hub 1 does not exist, allocating memory.
    [ 7.631183] /dev/vmnet: port on hub 1 successfully opened
    [ 7.649431] /dev/vmnet: open called by PID 528 (vmnet-dhcpd)
    [ 7.649442] /dev/vmnet: port on hub 1 successfully opened
    [ 7.659803] /dev/vmnet: open called by PID 536 (vmnet-natd)
    [ 7.659810] /dev/vmnet: hub 8 does not exist, allocating memory.
    [ 7.659822] /dev/vmnet: port on hub 8 successfully opened
    [ 7.662044] /dev/vmnet: open called by PID 537 (vmnet-netifup)
    [ 7.662051] /dev/vmnet: port on hub 8 successfully opened
    [ 7.672419] /dev/vmnet: open called by PID 542 (vmnet-dhcpd)
    [ 7.672431] /dev/vmnet: port on hub 8 successfully opened
    [ 8.032979] Bluetooth: hci0 command 0xfc8e tx timeout
    [ 8.033056] Bluetooth: hci0 sending frame failed (-19)
    [ 8.140139] cfg80211: Calling CRDA to update world regulatory domain
    [ 10.041263] Bluetooth: hci0 command 0xfc11 tx timeout
    [ 16.036148] Bluetooth: hci0 exiting Intel manufacturer mode failed (-110)
    [ 421.253320] usb 1-1: new high-speed USB device number 4 using xhci_hcd
    [ 421.429257] usb 1-1: ep 0x81 - rounding interval to 128 microframes, ep desc says 255 microframes
    [ 421.429265] usb 1-1: ep 0x2 - rounding interval to 128 microframes, ep desc says 255 microframes
    [ 421.439571] usb-storage 1-1:1.0: USB Mass Storage device detected
    [ 421.439662] scsi host4: usb-storage 1-1:1.0
    [ 421.439732] usbcore: registered new interface driver usb-storage
    [ 421.440704] usbcore: registered new interface driver uas
    [ 422.802584] scsi 4:0:0:0: Direct-Access PQ: 0 ANSI: 4
    [ 422.803405] sd 4:0:0:0: [sdb] 31129600 512-byte logical blocks: (15.9 GB/14.8 GiB)
    [ 422.804030] sd 4:0:0:0: [sdb] Write Protect is off
    [ 422.804039] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
    [ 422.804680] sd 4:0:0:0: [sdb] No Caching mode page found
    [ 422.809996] sd 4:0:0:0: [sdb] Assuming drive cache: write through
    [ 422.816610] sdb:
    [ 422.818457] sd 4:0:0:0: [sdb] Attached SCSI removable disk
    -- Logs begin at Sat 2015-05-02 12:41:07 CEST, end at Fri 2015-06-19 22:40:49 CEST. --
    Jun 19 22:30:21 WOOP-PLUTO systemd-journal[216]: Runtime journal is using 8.0M (max allowed 394.6M, trying to leave 591.9M free of 3.8G available → current limit 394.6M).
    Jun 19 22:30:21 WOOP-PLUTO systemd-journal[216]: Permanent journal is using 1.4G (max allowed 4.0G, trying to leave 4.0G free of 120.7G available → current limit 4.0G).
    Jun 19 22:30:21 WOOP-PLUTO systemd-journal[216]: Time spent on flushing to /var is 31.618ms for 2 entries.
    Jun 19 22:30:21 WOOP-PLUTO kernel: Initializing cgroup subsys cpuset
    Jun 19 22:30:21 WOOP-PLUTO kernel: Initializing cgroup subsys cpu
    Jun 19 22:30:21 WOOP-PLUTO kernel: Initiali

  • Hangs on boot with Logitech wireless keyboard

    I am running Windows 7 on a Thinkpad W510 and just bought a Logitech S520 wireless keyboard and mouse.
    When I try to boot, the system hangs at the Thinkpad splash screen.
    I updated the BIOS to the latest version but it had no effect.  I also changed the boot sequence so that USB boot was after HD boot.
    This had no effect and the system still hangs on boot.
    If I remove the USB receiver the system boots fine and I can then insert the USB receiver and everything works propely.
    Is there anything that I am missing?  This just doesn't make sense.
    Thanks for any further suggestions.

    I have the newer port replicator (issued July ?? 2010) and it is always plugged in to USB 2 port.  From the port replicator I go to a powered USB hub.  In the later I have the transmitter for my Logitech mouse.  I have never tried the Logitech transmitter directly in my laptop so can indicate whether that would hang my system and at least right now I'm not interesting in trying it.

  • K8N Neo 2 Platinum -- Hanging during boot --RESOLVED--

    Heres the problem...
    My system will hang during boot at anytime, from bios initalization to full windows boot (No BSOD ever and where the pc hangs in the boot proccess is totally random). And the only way to get past the hang is do a soft reset. I have to restart my system up to 3 times before I get a good boot, but once the pc is up and running, it stay running till I shut it down. (no hangs)
    Now if I shut it down after the system has been running for a while, the pc will restart normally without any hangs. The hangs only occur after the pc has been down for a time.
    I have reseated all the connectors, the memory (even tried different slots), add-in cards, cpu.
    I have a clean install of Windows XP Pro (hard drives have been repartitioned and reformatted as NTFS)
    All fans are spinning up fine, all temps are within norm, power supply voltages are within norm.
    No phsysical signs of bad caps on the system board.
    I ran ran Memtest86 for 18 hours striaght with no errors.
    Ran CPU stress test with no problems.
    No IRQ,DMA,etc conflicts found.
    Windows records no errors during a freeze and I have checked for unwanted services/proccess as well.
    I have tried min install to no avail.
    Bois is retaining its settings (so bios battery is good)
    I do not over clock anything. Bios is set to discover all important setting automaticly. (Bios setting are the same now as they were 6 months ago)
    I am down to a possible cold solder joint on the system board?
    This problem started to occur about a month ago.
    If someone has seen this exact problem and has a resolution, well I would appreciate it if you passed along your knowladge 
    I am down to my last option of RMAing my system board. No. I have not replaced any components due to the fact I don't have extras lieing around nor can I spend the money just to troubleshoot :(
    Specs..
    Athlon 64 3500+
    2 gig (pqi TURBO 1GB 184-Pin DDR SDRAM DDR 400 (PC 3200) Unbuffered System Memory Model PQI3200-1024SB)  Ran in Dual config
    Geforce 6800  (BFG 6800 GT oc)
    Creative X-Fi XtremeMusic
    Antec NeoPower 480
    2 WD 36gig SATA Raptors in raid 0 (system partition)
    2 WD 120gig IDE  in raid 0 (data partition)
    Windows XP Pro
    all drivers and bios are manufacture ref and up-to-date.
    Ok I won't go into all the details of why I missed this but it turns out the northbridge heatsink fan had stopped spinning and thus the hangs during boot due to overheating (hhmmm, when I step back and look at this the symptoms point right to overheating).
    This also expains why after several attempts at booting up, once the pc was up it would run like a champ. The chip would of course overheat and cause random freezes. Now due to the placement of the chip and the design of the heatsink once there was enough airflow over the heatsink the chip would remain cool enough to prevent further freezing of the system.
    What helped to facilitate this is that I have a ducted fan system installed in the bottom of my case which directs a substantal amount of fresh air to the pci slots, the chip set and the AGI slot as well.
    So what have we learned class?
    1. check the obvious
    2. do a complete physical inspection of your system
    3. KISS  -- keep it simple stupid

    Is this your ram:
    Quote
    Part Number: PQI3200-1024SB
    Quality Control: Comprehensively and rigorously tested
    Package: 1024MB single pack
    Organization: 128M x 64-bit
    CAS Latency: 3-4-4-8
    Test Voltage: 2.6 V
    PCB Board: 8 Layers PCB
    Heat Spreader: Mirrored Black Copper
    Speed: DDR 400 MHz (PC3200)
    Type: 184-pin DDR SDRAM
    Error Checking: Non-ECC
    Registered/Unbuffered: Unbuffered
    Warranty: Lifetime
    This is a quote from MSI web site:
    Quote
    Main Memory
      • Supports dual channel DDR 266/333/400, using four 184-pin DDR DIMMs.
    • Supports the memory size up to 4GB 
    • Supports 2.5v DDR SDRAM DIMM 
    Due to the High Performance Memory design, motherboards or system configurations may or may not operate smoothly at the JEDEC (Joint Electron Device Engineering Council) standard settings (BIOS Default on the motherboard) such as DDR voltage, memory speeds and memory timing. Please confirm and adjust your memory setting in the BIOS accordingly for better system stability.
    Example: Kingston HyperX DDR500 PC4000 operates at 2.65V, 3-4-4-8, CL=3.
    For more information about specification of high performance memory modules, please check with your Memory Manufactures for more details.
    Manually adjust your ram voltage to 2.65 volts and then manually adjust your ram timings to 3-4-4-8-2T.
    If that does not work then do as Richard suggested and strip down to a bar-bone system, this is CPU+fan, 1 stick of ram (try other stick and different slots as one may be bad), graphic card and PS-2 keyboard, if it boots fine without any problems then add one device at a time until you find the problem.
    Post back results as there are more things one can try but lets start with the simple stuff and work up.

  • [SOLVED] System hangs on boot, reinstalling Arch doesn't help

    After a recent upgrade (including the kernel), my system hangs on boot.  I have an Asus K40IN laptop, about 2 years old.  I've been running Arch for the life of the computer and never had any (serious) problems.
    I booted into a live Arch environment, tried rebuilding the mkinitcpio image, didn't work.  Tried downgrading the kernel, didn't work.
    I then assumed it was just some software issue that I couldn't figure out, so I reinstalled Arch.  No change.
    Here's what my screen looks like when it hangs:
    Any ideas would be very much appreciated.  I'm completely stumped here.
    Last edited by noahsark1126 (2011-06-15 23:32:34)

    jnguyen: 
    I have another arch system, a desktop, that I tend to keep pretty much in sync with my laptop.  So I can look in the logs on that system to see what was upgraded.  The other notable packages in that upgrade were probably udev, initscripts, and mkinitcpio.  I will try downgrading those.
    Leonid.I:
    I'm using the 2010.05 arch release, which has kernel 2.6.33.  I see two cores in the live env, as I should, and there's nothing to suggest any problems in the logs.
    I'm actually now getting a completely different hang screen:
    Of course I don't know what this one means either...

  • ACPI problem - random hang on boot

    Hi, I've just installed Arch 0.8.0 on my Sony PCG-XR1G laptop with Celeron 466Mhz and 128MB Ram. The installation CD hang at boot but I managed to get it work by using the kernel parameter acpi=off. After reboot, my new system still require the parameter acpi=off to boot correctly, or else 90% of the time it will hang (yes, 10% of the time it work perfectly). If I use acpi=off then I cannot shutdown my laptop completely, so I want to try not to use this parameter. Anyone have any idea? I'm running the newest kernel 2.6.20. Kernel 2.6.19 also have the same problem.

    Well, problem solved again, I think. My bios has a setting to turn on or off a feature to automatically lower the cpu speed on idle (quite funny with a celeron 466Mhz). Whenever I start the system and the kernel detect the CPU as 138Mhz (around that value), the system hang. Seldomly when it can get the correct value, it run perfectly. Still, I think there are some problem with the ACPI code in the 2.6 kernel. Or maybe it's just because my bios was too old, anyway.

  • P205-s6237 Hangs during boot to recovery after replace HDD

    I replaced a bad HDD and the machine hangs during boot to the recovery disk. it gets past the inspecting screen and then hangs when the VISTA dots appear. the dots continue to scroll left to right but nothing ever happens. Any ideads on getting it past this point?

    I replaced a bad HDD and the machine hangs during boot to the recovery disk. it gets past the inspecting screen and then hangs when the VISTA dots appear. the dots continue to scroll left to right but nothing ever happens. Any ideads on getting it past this point?

  • Deployment hangs after boot

    Hello Forum, I've run into a weird issue. Only one of my images will not deploy. It doesn't boot to the PXE environment, it hangs at the windows screen(see screenshot). I figured, maybe it's a driver thing, so I went to the manufacturer's site and grabbed
    the latest drivers as well as the Winpe drivers, still no go. Next, I deleted the deployment's boot folder contents and completely regenerated the boot files, still no go. I've also, rebuilt the wim file from scratch, still at a dead end. I'm totally baffled
    because only one of our models has this problem.
    version: MDT 2012 6.1.2373.0
    Hosted on Windows Server 2008 R2 VM
    WDS: NO 
    Since it's not booting to the PXE environment, it's not generating any logs files. Please Help
    IT Support " Scripting Noob "

    Sorry for the wait guys, I'm totally stuck now. Ok, here we go.
    1.) I moved the OS to a test deployment share, it booted to PE but failed due to no network driver. I added the drivers and tried again, it went back to hanging at boot. So, I removed ALL the drivers,
    verified the Out-Of-Box drivers folder was empty, and completely regenerated the boot files, it still hangs at boot. 
    2.) I thought the deployment share was caching the MAC or something so checked the deployment folder in the %temp% directory, it was empty.
    IT Support " Scripting Noob "

Maybe you are looking for