Tecra A3 battery stops charging after one or two seconds

Hello
I've been using the computer without the battery for a long time. Now, when I try to use the battery it is completely discharged (it says 0% º capacity).
It starts charging when plugged but after one or two seconds it stops so it keeps 0% capacity.
Any ideas of what can the problem be?
Thank you

Hi
Are you 100% sure that the battery stops charging?
How did you check it? What is the status of battery LED?
If you plug the battery the notebook must be off.
Furthermore the charging procedure takes several hours if the battery is empty.
I think you have to connect the AC to the notebook and wait several time.
But if the battery will not charge so either the battery is dead or the notebook electronic malfunctions.

Similar Messages

  • How can i make my ipod battery stop charging after its fully charged?

    My ipod always shows a lightning icon right next to the battery icon when its charging and it disappears when its fully charged, lately even though its fully charged the icon shows there anyways lIke its still charging. I dont want my battery to ruin so, do you guys have any ideas of why does this happens now? Have a Blessed day

    Not Charge
    - See:    
    iPod touch: Hardware troubleshooting
    iPhone and iPod touch: Charging the battery
    - Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
    - If a 5G iPod      
    Iphone 5 lightning port charging problem - SOLUTION!
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
      Apple Retail Store - Genius Bar

  • G505s Battery stops charging at 60%

    The battery in my new G505s stops charging at 60%. Clean windows 8 then windows 8.1 install. The lenovo site has no power managament drivers for windows 8.1. Is this because windows 8.1 installed the lenovo app on its own? Because it is on the computer and i certainly didnt put it there. This happened after i upgraded from windows 8 to 8.1. It was 100% before the upgrade and 70% after. The lenovo energy management program has two settings. Maximum battery life and optimized battery health. No matter which is selected, charging stops at 60% and says plugged in not charging. I tried doing the battery gauge rested and it doesn't work. I press start and it does nothing. I drained the battery to 0 then charged it up but that didn't do anything. The dust removal button also doesn't work. On  side note, what graphics drivers is everyone using? i have the ones from lenovo installed. It looks like they were updated a few months ago. Would the generic AMD ones work better? 

    Hey Guys, For all those who has issue with their laptops "Battery stops charging at 60%" Here's the solution: (These are the settings of my Lenovo ideapad Yoga 13, yours will be similar or slightly different) - Go to control panel- System and security (Category View)- Power options (Small icons)- There will be one option selected for your power plan.. click on "change setttings plan" of that plan- Now click on "change advanced power setting"- You now will see two tabs on the pop up window that comes up.. "Advanced Settings" and "Lenovo Energy Management".. - so go to tab which reads.. "Lenovo Energy Management"..- now click on "Enable Lenovo Energy Management"..- You will get another pop up window for "Energy Management"..- Under the Battery option which is in the center you will see 3 options..- Click on the centre one.. which has a "wrench" symbol meaning for settings..- And now click on "Start"..- Voila!!! Problem Solved..- Now battery will be able to reach 100% complete charge..!- Have a Gr8 day peeps!  Best RegardsFirdaus [email protected]

  • Ipod stops charging after a few seconds

    My 4th gen ipod stops charging after 6-8 seconds of being plugged in. Since the battery is dead, the black screen with a red battery pops up whenever it's plugged in and then disappears after 6-8 secs or being unplugged. Both the home and power buttons are broke so I'm unable to activate in any way besides plugging it in.

    Not Charge
    - See:    
    iPod touch: Hardware troubleshooting
    iPhone and iPod touch: Charging the battery
    - Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
      Apple Retail Store - Genius Bar

  • My ipod battery stops charging in ios 7

    my ipod battery stops charging in ios 7

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    iPhone and iPod touch: Charging the battery
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use. Also. iOS 7 made the iPod more sensitive to defective cables.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar                          

  • How can I make the iPhone podcast app automatically stop playing after one episode?

    How can I make the iPhone podcast app automatically stop playing after one episode?

    When playing a song, are the controls at the top of the screen there? (Genius, Shuffle, Loop?)
    If not, tap the center of the page once to expose them
    now keep tapping the circle on the left part of the exposed controls untill a one (1) appears...

  • Ipad4 stopped charging after ios7 update

    My ipad 4 stopped charging after the ios7 update. How can I resolve this issue?

    Try reset all settings
    Settings>General>Reset>Reset All Settings
    Note: Data will not be affected but settings for Wi-Fi, FaceTime, Message, Home Sharing, Wall Paper, Sound etc will be reset

  • Does battery stop charging automatically

    Hello,
    I like to keep my laptop plugged in while using it.  Does the battery stop charging when it is full?  What is the best way to use the laptop.  Leave it plugged in when you can, or always run on battery?
    Regards,
    Randy.

    ALL Li-ion batteries stop charging when they are full.  They have an internal micro-controller to enforce this. 
    I run my MBP down to about 20% charge left and then recharge on a daily basis.  The run time depends on what you are doing.  Heavy usage will reduce the run time.  Flash web sites, playing movies, maximum screen intensity, bluetooth on are all examples of things that will reduce run time. 
    Think of a battery like a bucket of water.  If you let the water trickle out it will take a long time to empty the bucket. If you turn the bucket upside down it will be empty in a few seconds.
    In other words a battery holds a fixed amount of energy.  The rate at which you discharge it will determine the run time.  As the battery ages the amount of energy that it can hold will go down.  The battery will age whether or not you use it.  Regular usage will give the longest overall life for the battery.

  • Satellite A30: while AC adapter is connected the battery stops charging

    Using a Satellite A30 about three years old. Recent problem is that while the power adapter is connected the battery stops charging, the orange battery indicator goes off.
    If you look at the Power Management Utility the battery poweer meter reads On Line, Discharging %
    To get it to charge I either have to turn the machine off (completely or to hibernate) then remove the power cable and reinsert, then the battery light comes back on. When restarting the battery will start to charge up for a while and then for no apparent reason start to discharge.
    If left the battery reaches 0% - the machine continues to operate while the power cable is inserted so its getting power ok, but of course starts to bleep when it gets below 10%. To get it going again I have to shut down and restart etc.
    I have checked the bios and have the latest version.
    I have cleaned around the heat exchanger the power socket and removed all fluff.
    I am using a generic adapter as the original failed, but as far as I can tell its working normally.
    Any thoughts
    Richard

    Hi Richard,
    Your problem is being caused by a loose connection where the AC adapter is connected to the socket on the back of your notebook. Any slight movement of the cable causes a momentary loss of contact and the power management electronics in the notebook are fooled into beleiving that the battery is no longer available, whereupon the battery light will extinguish and the notebook will revert to battery power even though the AC adapter is connected. As you have already discovered, powering off the notebook will return everything to normal.
    I have experienced the very same situation with my A30-141 and have yet to find a solution other than to resort to powering off the notebook, but I have managed to prevent the problem from occurring by clamping the AC cable to the back of the notebook so that there is no risk of the power plug flexing so as to trigger the problem in the first place. This has been remarkably successful to date and I have not experienced the problem for several months now.
    Obviously this is not a 'cure' for the problem but it does ease the frustration that it causes.
    regards,

  • TS1388 After one or two websites the search "freezes". To rectify this I need to go into "Network" and press "Renew DHCP Lease" on my imac 10.6.8

    After one or two websites the search "freezes". To rectify this I need to go into "Network" and press "Renew DHCP Lease" on my imac 10.6.8TS1317 - Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connectionAny help?

    Check your computers time and date are correct, and updating to your location via Apple's servers.
    WiFi, Internet problems, possible solutions

  • Photoshop CC 2014 stops working after less than 30 second and shuts down

    I have installed and uninstalled Photoshop CC 2014 three or four times via Creative Cloud and each time it stops working after less than thirty seconds and shuts down the program. I then installed a an older version of Photoshop CS5.1 from a CD and it works perfect. I also have Illustrator CC 2014 and Lightroom 5 installed from Creative Cloud and both work flawlessly. What can I do to get Photoshop CC 2014 working?

    You have not provided any system information or crash logs, so we can't really know.
    http://myleniumerrors.com/working-with-your-operating-systems-tools/
    Mylenium

  • Videos stops playing after 5 0r 6 seconds, how do i fix this problem

    videos stops playing after 5 0r 6 seconds, how do i fix this problem ?

    Howdy z71jimmy,
    The following article provides tips that can help resolve most playback issues in iTunes for Windows.
    Troubleshooting iTunes for Windows Vista or Windows 7 video playback performance issues
    http://support.apple.com/kb/TS1718
    Cheers,
    Allen

  • I've tried 2 different screen capture devices, and in both cases, audio stops recording after 20 or 30 seconds, but video is fine.  The audio disappears

    I've tried 2 different screen capture devices, and in both cases, audio stops recording after 20 or 30 seconds, but video is fine.  The audio disappears with both programs.  Does anyone know what is happening with my audio capture?

    Update, I took the webcam home over the weekend and tried on my home network and the outcome was the same video fine - audio delayed, is this a Skype for desktop issue?

  • HT204387 I lose my contacts on the car blue tooth after one to two weeks and have to reload them..This was only after the lates OS update.

    I load my contacts from my phone to my car Blue tooth.
    After one to two weeks they are no longer there and I have to reload them.
    This has happene after the latest OS update.
    Any suggestions?

    Try:
    - Reset the iOS device. Nothing will be lost      
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings                            
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                               
    iOS: Back up and restore your iOS device with iCloud or iTunes
    - Restore to factory settings/new iOS device.                       
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • When i play my song after one or two min the voice becomes vibrated

    hi when i play my song after one or two min the voice becomes vibrated not well,please solve my problem. 

    Do you have repeat on? You can check this in now playing screen. Tap once at the centre of the screen, make sure the leftmost icon below scrub bar is not blue in color.

Maybe you are looking for

  • Ok I am having issues with my HP Enby 100 D410. Need help setting up eprint, and keeping connected.

    I opened up my printer, set it up, connected.  But I cant seem to keep connected.  I have an eprint email address set up, but the printer reset and now wants me to set up an new eprint using a different code.  How do I get the [email protected] email

  • Cable connection between card and dri

    Looking for a round cable to replace flat cable that connects sound card to dri've! I know they make round cables for other dri'ves to dress up tower looks and air flow but does anyone make one for the Creative dri've and card connection?

  • WebDynpro program not working in some other place

    Hi friends... I am new to WDA... In my client place, i created one sample WebDynpro program.. it was worked fine...i could able to saw the output in Internet browser also... now i am working in another project ( i mean another server) through remote

  • Update java server from 7.00 SP17 to 7.05 SP05 with EHPI

    hi all i' m upgrading a java server from version 7.00 SP17 to version 7.01 SP05 (ehp1) with the EHPI installer during the phase  PREPARE_JSPM_QUEUE i get the error that the jspm has already been started any ideas regards tom file: TroubleTicket_01.tx

  • Question about Curves

    Sometimes in Curves I see the Channel set to RGB and other times Luminance. Does it matter what the Channel is for a Curve?