Tecra A3 does not work after changing power settings

I changed my power settings in my tecra a3 laptop and now it won't start properly. wants to start but just keeps going back to press F2 or F12 please help.

Hi,
where did you changed them? In the BIOS or in the Toshiba HW-setup?
I would suggest you to go to the bios after powering up your machine. You must just hit F2 ant then in the bios search for the setting "setting everything to default" or something with "bios setup defaults" to reset your bios settings.
After that your machine should boot up again.
Greets

Similar Messages

PCI wireless card does not work after restart - FM2-A55M-E33

Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
Does anyone know more about this issue?

Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
I am unable to find any useful information in the logs.
Got any more suggestions?
Thanks! (And sorry to disturb so much)

Apple av adapter does not work after updating ios 5,01

apple av adapter does not work after ios 5,01. no video on vga monitor. sound goes out on iphone 4 also.

Thank you for your interest. Last night i tried again. It worked. there is still problem, so i could find out it that monitor is going to power saving mode then voice goes out and no view on monitor. I changed the power saving settings. And worked well. Thnx again.

Auto brightness does not work after upgrade from iOS5 to iOS6 on my iPod touch. Is this intended by Apple, or is it a bug?

I attempted to ask this question, yesterday. However, I am not used to typing with my thumbs, yet, and messed it up some. So, I will give this another try. Auto brightness does not work after upgrade from iOS 5 to iOS 6 on my iPod touch. Is this intended by Apple, or is it a bug?

Have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?
iOS 6 changed how that feature works.

Canon 60D does not resume after auto power off

My Canon 60D does not resume after auto power off. It shows the empty battery icon when I press the shutter button, even the battey is fully charged. If I remove the battery and insert back it will resume to work. Any one had the same experience and know how to resolve it?

The power switch is actually a "software" switch. It's not like a light switch in that it doesn't actually provide or deprive the camera of power... only removing the battery will deprive the camera of power. This is why it doesn't actually just go dark when you switch off power... instead you'll usually see it perform a sensor clean cycle and then power down. The camera is technically in a kind of "sleep" mode monitoring the switch. If a Canon camera ever seems to lock up and ignore all input, the battery should be temporarily removed to "reboot" the camera. There is no "setting" in a camera that can configure it to ignore buttons. Although... if the camera is in an automatic mode, some input is deliberately ignored to make it easier to use the camera. Put the mode dial in a "creative zone" mode (P, Tv, Av, or M) and all buttons and menus should be accessible. You might try connecting the camera via USB cable to your computer and then attempt to control the camera via the Canon EOS Utility to see if that works. If the camera responds fine to the computer control, then likely the camera's main board and circuits are working fine and it may just be a wiring problem -- as if some cable simply isn't getting a very solid connection. If this is a wiring issue, you are probably better off sending it in for service.

Continuous with the problem, the headphone does not work after having my iphone ios 8.0.2 updated

the headset does not work after having my iphone ios 8.0.2 updated to me is very annoying to have to be answering speakerphone is not private and can not go with the hands-free all the time

I had the same issue until I updated my apps through iTunes. I had over 100 updates, but none of them showed on my iPod. After they updated everything started syncing like it is supposed. Go to the apps library and check for updates. After everything syncs leave your iPhone/ipod/ipad connected if the spinning arrows at the top is still spinning. It means that things are still being added. If you go to settings > general > about, you will see it loading songs, videos, photos, etc. If you back out of "about" and then go back to it you will see the numbers for each one change.

RDP does not work after disabling TLS 1.0

RDP does not work after disabling TLS 1.0
Had to re-enable it .... what can i do to make it work with TLS 1.2 ??

Hi,
Disabling TLS 1.0 will break RDP under default settings. Did the security scan say specifically to disable TLS 1.0? Normally you should be able to disable use of certain ciphers or prioritize ciphers. You may want to try IISCrypto, on
it you click the PCI button, then Apply button, then restart your server.
Additionally there are still a substantial number of web browsers in use that do not support TLS 1.1/1.2.
If you would like to continue with TLS 1.0 disabled you may change the RDP Security Layer. To do this please open Terminal Services Configuration (tsconfig.msc), double-click RDP-Tcp, change Security Layer to RDP Security Layer.
IMPORTANT: You are vulnerable to MITM attack when using RDP Security Layer because there is no Server Authentication. If you are running RDP over a VPN connection and there is no risk for interception then this may be okay. I recommend
you re-enable TLS 1.0 and have a ssl certificate from a public authority set on your RDP-Tcp listener.
Quoted from this thread answered
by TP, for more information you can go through that thread.
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Satellite A110-228 LAN does not work after hibernate

Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
After a reboot, the network functions as usual (gets a IP address from the DHCP server)
Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
The wireless network will be restored after a hibernate.
It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
Any suggestions?
Wilm Boerhout

Hi guys
In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
I think the options are disabled by default.
Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
Please check this how to enable WOL (first time use):
1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
2. Enable Wake-up on LAN
3. Click [Apply]. System will request to reboot.
4. After the reboot go to [Start] -> [Control Panel] -> select [System]
5. On system properties dialog box select [Hardware] tab -> click [Device manager]
6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
8. Press [OK] to close the dialog box.

Satellite L870-165 does not work after being repaired by their service

Laptop Toshiba warranty does not work after being repaired by their service twice.
Model: Satellite L870-165
Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
After reboot still happening the same.
I called Toshiba phone incident and after trying several options I said take him to repair the service.
They first told me it was the hard drive, then phoned me to indicate that reinstalling and finally it was the motherboard, which supposedly changed. The day after being picked computer repair returned to give exactly the same error, only malfunctioned one evening.
After another call to 902 the Toshiba warranty service, I went back to take the service, this time I changed the hard drive. When I got home the computer did not start even once, again gives the same error.
I believe that this team comes with a factory default so that its solution is not easy because even the technical service told me that I did not know what else to do with it.

>Computer will not boot, stays with black screen stating: No bootable device-Please restart your system
This message pops up because the notebook cannot find the Windows system.
There could be either an problem with the HDD or maybe the HDD is OK but the Windows system isnt preinstalled properly.
You said that the service agent changed the HDD. But did someone install the Windows system?
You can try to do it yourself take your recovery disk (hopefully you created such disk in the past) and boot from the recovery disk in order to install the system.
In case booting from the Disk would not be possible, go to BIOS (F2) and disable the secure boot and change from UEFI to CSM mode

Card slot does not work after update (14/10/2011)

Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8

Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

HT1688 My Hot Spot does not work after update to 6.0.1. Service is with ATT. Apple says problem is with ATT, ATT says problem is with Apple. Anyone else having this problem?

My Hot Spot does not work after update to 6.0.1. Any suggestions?

Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

Click to activate does not work after update

Click to activate plugin does not work after updating to version 23.0.1

hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.

WiFi iPhone 4S does not work after update iOS 6.0

WiFi iPhone 4S does not work after update iOS 6.0

This sounds more like a hardware issue.
Have you checked that the dock connector port is not dirty?

Flash player does not work after I installed it

Flash player does not work after I installed it

I'm using Mac Osx and my browser is Safari
Date: Wed, 5 Feb 2014 00:41:29 -0800
From: [email protected]
To: [email protected]
Subject: Flash player does not work after I installed
    Re: Flash player does not work after I installed it
    created by Mike M in Installing Flash Player - View the full discussion
This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
What OS are you using?
http://mmonlinedesigns.com/images/os.png
What browser?
http://mmonlinedesigns.com/images/browsers.png
     Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
     To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
           Start a new discussion in Installing Flash Player at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

My sound system does not work AFTER installing pc to tv wireless connection

my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

Hi,
You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
one used by the Form contact for Form Invoice.
Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
VS General Question forum mainly discusses
the usage of Visual Studio IDE such as
WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
System and Visual Studio Editor.
Thanks,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Tecra A3 does not work after changing power settings

Similar Messages

Maybe you are looking for