Tecra A7 - After BIOS update it does nothing

Hi all,
I d/l and ran the 'windows' BIOS update for my model of Tecra A7. With power supply in, I watched the update go through all steps including BIOS backup, but at the final step 8 of writing to the BIOS, it looks like it hung. I waited over 2 hours and decide to reboot.
You guessed it, now I have absolutely nothing - no Toshiba screen, no BIOS, nothing.
Is there a way to reset the BIOS or bring back the backup? I don't have the recovery CD (work loaner laptop - no idea where the CD could be). I am making a request for DVD with Toshiba (if in fact it will help me?) but meanwhile any good techies out there? No floppy drive only CDROM.
I'm lookin at my board now, where's the battery? rock on bros.

Hi
First of all the Toshiba recovery disk will not help you. It can only restore the OS (Windows) and has nothing to do with the BIOS.
Furthermore in this case you can do nothing because need help from an authorized service provider. Only authorized technicians can try to reflash the ROM module. Here you can search for nearest:
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an authorized service provider
Good luck! :)

Similar Messages

  • Satellite A series does not start up after BIOS update

    After bios update with downloaded utility my notebook does not start up.
    Did this case covered by warranty?

    Im not quite sure if this would be covered by warranty. You should contact the ASP in your country for details but I presume its not covered.
    PS: Did you try this workaround:
    - remove battery, disconnect the AC adaptor
    - wait ~ 40min
    - connect both devices again and try to power up the notebook

  • Hi . plz help me. after bios update. i could work till I shutdown

    After bios update I could work till I shutdown my laptop g510 . Now when I press power button. White light near camera shows but again it goes off. Plzzzzz help me
    I also pressed one recovery. Then pressed f2 and f9 f12 nothing working.

    take it to point of purchase with proof of purchase if you can't find a Nokia care point near you
    If  i have helped at all a click on the white star below would be nice thanks.
    Now using the Lumia 1520

  • Satellite A100-590 PSAA9E freezes on Toshiba welcome screen after BIOS update

    Hi.
    Yesterday I did a BIOS update on my Satellite A100-590 PSAA9E-03Z00QGR with the appropriate flash:
    http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?service=EU&selCategory =2&selFamily=2&selSeries=153&selProduct=624&langua ge=17&selOS=10&selType=all&yearupload=&monthupload =&dayupload=&useDate=null&mode=userMachines&search =&action=search&macId=&country=all&selectedLanguag e=17&type=all&page=1&ID=58477&OSID=-1&driverLanguage=42
    bios-20070709111839.zip
    After the flashing procedure the machine rebooted automatically, but unfortunately it now keeps hanging at the Thoshiba welcome screen. Also pressing F2 or F12 won't change anything. It seems like the BIOS is corrupt.
    I saw, that in the BIOS package are delivered two flash files (s10gm590.rom and s10pm590.rom). But just executing the SanAntonion10 BIOS590MP.exe a .vbs script is started that decides automatically chooses and loads a flash file. Maybe it chose the wrong one?
    What shall I do now? Is there a way to restore the BIOS, or do I have to send my notebook in?
    Thanks in advance
    MAT

    > Satellite A100-590 PSAA9E freezes on Toshiba welcome screen after BIOS update
    What to say Marc. It looks like you have used a wrong BIOS version or you have updated the BIOS in wrong way.
    You could try to access the BIOS and try to set the settings to default.
    Dont forget to save the settings if you will exit the BIOS.
    But if this procedure does not help, you will have to contact the ASP in your country.
    Possibly the guys will try to flash the BIOS again with other special version.
    Good luck
    Greetings

  • After bios update side nomberpad is not workinh keys from 0-9

    after bios update side nomberpad is not workinh keys from 0-9

    Hello jay04,
    Welcome to the HP Forums!
    I understand the number keys do not work on your keyboard. I will do my best to assist you. First, I require the following information:
    1. The computer's model number. If you require assistance locating this information, please reference this website: Guide to finding your product number
    2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
    3. Does this occur on certain programs, or all programs?
    4. Have you installed any new software or drivers on this computer, before the issue appeared?
    Additionally, if the issue just began occurring, I would perform a system restore. I want you to bring the computer back to the earliest restore point possible, in an attempt to dodge whatever caused the issue. Here is a document on how to perform a System Restore: System Restore
    Thanks!
    Mario
    I worked on behalf of HP.

  • Satellite Pro C850 wont work after Bios update

    my satellite pro c850 cd wont work after bios update from toshiba.
    what do i do?

    Saying: dont work you mean it does not power up or what do you mean exactly?
    Did you flash the BIOS properly?
    Possibly something went wrong during the update and this means that ROM module isnt flashed properly
    In most cases a special BIOS crisis disk would be needed to get it working
    Not quite sure if you can get it fixed by your own
    Check this thread. Maybe it helps:
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=59637
    Otherwise you need help from authorized service provider available in your country.

  • Satellite L650-1KR PSK1JE - dead after BIOS update

    As the subject already states, my Satellite L650 - 1KR Part No. PSK1JE is totally OFF after BIOS-Update 2.40-WIN from bios-download-page.
    I tried everything: Press all buttons, take out the laptop battery, only laptop battery, ...simply nothing!
    My last hope is a hidden, very special key sequence for toshiba laptops or something like this.
    Of course my warranty is already over... :-(
    Please help!
    Thank you in advance...
    lichtimc

    Sorry to hear you have such problem now. I presume something went wrong and now the BIOS chip is screwed up and in such situation you need professional help. Toshiba service provider can help you with this but Im afraid it can be very expensive.
    In the past I never had such problems but on the net you can find many pages with description what can be done. Visit this page and check if you can find something useful there. I mean you can try to fix it alone.

  • Bios update failed : does not meet system requirements code 9994/9996

    bios update failed : does not meet system requirements code 9994/9996 / Model ny801av-aba HP Pavilion p6100z cto Desktop  windows vista basic  current bios version 5.38, released 03/20/09. 4GB ram (3.5 useable) AMD semperon LE- 1300 socket am2+  code name sparta.  M2N68-LA Motherboard BIOS update verision 5.49 released 08/24/09      (am trying to upgrade to a AMD phenom triple core 8400 2.1 gig that is why I am trying to update the bios, when I put it in I got nothing.)
    This question was solved.
    View Solution.

    Figure 1: Error message
    The error displays when ...
    the update requires certain hardware or software that is not installed on your computer (examples: keyboard replaced with a non-HP keyboard or Microsoft .NET software is not installed),
    the computer does not meet a certain minimum hardware or software requirement (examples: 4 GB minimum memory, 200 MB free disk space, or .NET version 2.0 required and 1.0 is installed) .
    Usually, this error indicates the update is not needed for your computer and it should not be installed.

  • I can't activate windows 8.1 pre-instal​led on my Toshiba E45-B4200 after BIOS Update

    I bought Toshiba laptop Model E45-B4200, at first time I could activate windows 8.1 like a charm.
    Few months later Windows 8.1 has crashed, so I did clean install of pre-installed windows, no problem so far. Toshiba Application installer app has downloaded BIOS update, so I ran it.
    I tried to activate windows after BIOS update, but it didn`t work. No error message, but Change PC settings window just got minimized every time that I tried to click on Activate Windows option. I thought that I did some mistake, so I repeated windows reinstallation, and same problem occurred again.
    Now I can`t update Windows, Office 2013, and so on. 
    I`ve tried SLUI 4 command to force activation by phone, but it didn`t work as well.
    I read on MS blogs that windows 8.1 stores product key on MSDM table, windows should be activated normally. Now I got no options now, can you help me?

    It shouldn't need to be activated it. Everything should be automatic. Because it's asking you, that's already indicative of a problem. You might want to call customer support.
    - Peter

  • Problem in booting after bios update

    Originally, it was windows home basic was installed in my laptop. But recently I had installed Windows professional. After installation I have downloaded all drivers which are compatible for my laptop model. After BIOS update installation my pc is not booting up at all. Only power button, WiFi and capslock is lighting. Capslock is continuosly blicking. Even FAN speed gets lowered. I have tried hard reset as well as windows+B comand during startup still condition is same. Please reply me....

    see help 8....
    I am a Volunteer to help others on here-not a HP employee.
    Replies aren't online 24/7 because of Time Zone differences.
    Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

  • After BIOS update Satellite L350-172 doesn't start anymore

    Satellite L350-172 Bios-Update from bios-20090203164614 to bios-201002250
    I just updatet the BIOS of my notebook from 1.60 to 2,20. Now the Notebook doesn't start any longer.
    "It was stopped for reason not to damage the Computer" - blue schreen.
    How can I downgrade the bios again? Or - what have I to change in the bios-settings?

    Hi schuwe,
    Im a little bit confused about your posting. How do you tell your BIOS not to restart?
    Anyway, after BIOS update you should load the default settings in BIOS.
    Did you choose the right BIOS especially for your model?

  • HT4623 I have updated my iPhone 5 but after this update it does not accept charging

    Dear Sir/Ma'am,
    I have update my iphone 5 software with iOS 7 but after this update it does not accept the charger or neither any charging ?
    I need to know how to solve this issue please.
    Thank you

    Well when you download the update with iTunes it will always download the whole new version (in your case 7.0.2) even if its just an bug fix. If you already have 7.0 download the update over-the-air.
    You already wrote that the update is only 21 MB, so its not the whole firmware package of 7.0.2 you get with iTunes.

  • When i tap "update" on an app, or try and download a new app i get the loading wheel for around a second then it goes back to showing "update" and does nothing.  Any solutions for this?

    When i tap "update" on an app, or try and download a new app i get the loading wheel for around a second then it goes back to showing "update" and does nothing.  Any solutions for this?  This is relevant to an iPhone 5S running iOS 8

    If you're really running iOS 8, you should be posting in the Developer's Forum, as you well know since you signed an NDA when you signed up for the Developer's program.

  • After BIOS update DVD driver do not read DVDs anymore - Sat A80

    Hi,
    I have a Satellite A80-131 and after bios update (last version 2.5) by windows procedure update, my DVD drive do not read DVD medias anymore. It is possible to read CD medias, but not DVD one.
    Can I reinstall the old bios? Can I reinstall the firmware?
    Thanks
    Ronai Lisboa

    Hi Ronai
    Like Jimi has said in the posting above. It's very unusual that after BIOS updating the DVD drive hasn't read the DVDs.
    Furthermore it's not advisable to use any 3rd party applications to DOWNGRADE the BIOS. Usually only the ASP can downgrade the BIOS. Such procedures are very serious and the wrong procedure can damage the motherboard.
    However, it's nice that you have solved the problem and that the drive works properly.
    Thanks for the feedback.

  • Satellite Pro L300: BSOD after BIOS update

    Hi
    after update the Bios of Satellite Pro L300, the windows not start!
    Its show the blue dead screen!
    What can i do?

    Hi
    Are you able to access the BIOS settings?
    Im not quite sure why this BSOD appears but possibly the SATA mode settings have been changed after BIOS update
    Usually the SATA mode should be set to AHCI if the SATA drivers are installed.
    But if the SATA drivers are not included the SATA mode should be set to compatible.
    Please check this!
    Furthermore you could set the BIOS to the default settings and could try to boot the machine again.

Maybe you are looking for

  • Open a new page

    Hi! In my application, I've an html file and i want saving or opening . With IE, when i open it, it opens in the same page, instead i want to open it in a new page. Basically i know how to open a new page, but i don't want to open it when i choose to

  • 3.12 post element text appearing on new line

    I have an icon and some javaScript behind it to clear the content of the item, which on moving to 3.12 is moved onto the next line: http://apex.oracle.com/pls/otn/f?p=41395:10 Is there a simple way of avoiding this please so that it all appears on th

  • Could not connect to store

    Everytime I try to log into to the store I get error "iTunes could not connect to the music store. The network connection was reset." And this account was set to be able to set up on two computers. It works on one but not this one.

  • Editing form issue

    I created a form in Adobe Acrobat XI Standard and am no longer able to edit it.  It isn't secured or protected so I do not understand why I can no longer edit it as I have been able to do so in the past.  Any suggestions? 

  • Ant Help

    Folks, How to compile multiple java clases and then make jar file using ANT tool ? Anticipating Help Thanks Randhir