Tecra R940-1EE - dead with lead error 4Eh

Hi.
Last night without any warning my laptop stopped working. I've tried with and without battery, pressing the shutdown button for 20/30 seconds without the battery, with battery, without the DC adapter, etc.
The error code I'm getting on the power led (blinking in orange) is 01001110 - 4Eh.
Does any one knows what this error stands for? I'm pretty sure this is a power related issue, but I'm not able to find what the error codes means.
Thanks

Hi
Googling around I found info that error codes 4*h means that there is some error with S3V output.
There is no 4Eh 4Eh code.
Just folow codes are available:
40h S3V voltage is over 3.47V.
45h S3Vvoltage is under 3.14V.
46h S3V voltage is under 3.14V or less when the computer is booting up.
That’s all I found online in different forums.

Similar Messages

Tecra R940 with SSD Windows 7 boot failure

My company has purchased Tecra R940 laptops and are replacing the existing HDD with Kingston SSDNow 200 V+ 120GB SSD drives. On a test unit after installing the SSD, the laptop was rebuilt with our corporate image (Windows 7 x64) which completed successfully.
Post build however a number of issues are apparent:
1. Occasionally during a reboot, the laptop will post and then hang at the "starting windows" screen before the Windows logo animation is displayed and with the hard drive light on solid. After a period of time an Windows recovery is attempted and eventually an error reported:
Status: 0xc00000e9
Info: An unexpected I/O error has occurred
This issue does not occur at every boot but once in every 2 or 3.
2. The following error is logged in the Windows System log
Source: ATAPI
Event ID: 11
Description: The driver detected a controller error on \Device\Ide\IdePort0
I have tried the following in order to resolve the issue:
1. Upgraded the R940 BIOS to latest available (6.40).
2. Confirmed that the BIOS SATA Controller Mode is set to AHCI.
3. Confirmed there are no available SSD drive firmware updates.
4. Installed the latest Intel Rapid Storage Technology Driver from Toshiba (11.0.0.1032).
5. Tried an alternate SSD. Same errors noted, so not a faulty SSD.
6. Tried the SSD in a Toshiba Portege R930. In this case the errors above are not apparent.
7. Reinstalled the original HDD. In this case the errors above are not apparent.
8. Confirmed a 2nd unit (with SSD installed) logs the same Event ID 11.
My testing has left me at a point where I believe there is something wrong at the R940 end with either hardware or software that does not like SSD's.
Has anyone resolved a similar problem or have any thoughts on resolving this?
Thank you in advance.

> Reinstalled the original HDD. In this case the errors above are not apparent
So using an HDD everything works properly
So the controller seems to be OK.
I searched for Even ID 11 error description and the Event ID 11 source disk means The driver detected a controller error on \Device\Harddisk0\DR0
There are many people having such issue with different notebooks and different SSD drives.
There is also different recommendation to solve this:
Someone could solve this my SSD drive firmware update
The other one solved this by running a full SMART scan with repair (reallocation of unstable sectors)
There is also an newer version of the Intel Rapid Storage Technology Driver available on Intel page.
So its worth to update this,
http://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=21730

Is my HD Dead? Reformat Disk Utility Error: secure disk erase failed with the error could not open disk.

Hi,
Fed up with seeing the spinning beach ball I decided to reformat my MacBook Pro...
After backing up everything on an external hard drive I put in the OSX install DVD, restarted the machine and held down 'C'.
I followed the install prcedure, clicking next a few times etc...
I then went into Utilities > Disk Utility. I chose 7-Pass to erase the Macintosh HD and set it off erasing.
I checked the process an hour in and message on screen read:
Secure disk erase failed with the error:
could not open disk
The internal hard drive no longer exists in the disk utility so I cant retry erasing it.
The only thing that appears in disk utility is the OSX install DVD.
I can't even shut down the mac as everything under the apple tab is greyed out!
I'm guessing this means my hard drive is broken right?
If anyone has any other ideas of what to try I'd really appreciate that.
How do I turn the machine off?
If my hard drive is gone then should I consider getting an SSD drive?
Any recommendations for such a drive would be great.
Hope you can help!

Did you partition the drive?
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

Rendering of Proxies in AE fails with generic error messages.

*sigh* working with AVC in CS4 on my quad core has been an exercise in pain.
I've followed the optimization guides linked to in the different forum posts and that lets me zip along until I actually start adding effects. Then I am right back to a crawl. I recently discovered proxies in AE and learned that I can use "replace" in premeire to leverage those same proxies... Sweet... When I works I am back to editing in both in real time!
The problem is AE is regularly failing to generate proxies for me and I cannot figure out why. All my video is shot the same 24mbps, 60fps, 1080p (true 60i). All shot from my Canon HF S10.
The error is always "Error reading frame from file" and it always occurs just before the render is about to complete. Sometimes I get lucky and a working .mov was generated in spite of the error. Bu most times the file isn't there.
So my 2.4ghz quad core with 8gb ram can't edit the originals and I can't create proxies... I'm effectively dead in the water.
I tried using Media Encoder to generate my proxies with no success either. It fails with "Unspecified Error".
Both times I am trying to encode to Quicktime, Jpeg, Draft Settings. For the heck of it I tried different codecs, etc. Nothing seems to help. Even worse is sometimes if I just queue the same file multiple times it eventually works.
Is there anything at all I can do to make successful proxy generation less like winning the lottery?

Yeah I updated to that right away. Premiere itself seems to behave most of the time. To be honest I've hardly had any problems with Premiere even before the 4.2 update.
But AVC (mts files) seem to be very problematic in AE in general. I also experience the issue mentioned here:
http://forums.adobe.com/message/2404464
Sounds like re-encoding to another format is the only way I'll be able to work in AE reliably. So I have to figure out a way to get Media Encoder to finish it's jobs.

Please help me with this error: "Apple application support was not found... Error 2"

Can anyone please help me with this error: "Apple application support was not found... Error 2"
I've followed the instructions by removing all Apple files from my laptop, but when I reinstall the iTunes software it still comes up with this message:
"Apple application support is required to run iTunesHelper. Please uninstall iTunes, then install iTunes again. Error 2"
Thank you

iTunes "Apple Application Support is required... Error 2" and possible fix.
I know this is a bit late but I came accross this thread trying to resolve this same problem and came up with a solution that worked for me, so thought I would share it here too. I hope it helps someone else.
I just resolved this on Win Vista (should apply equally for Win7 too). Please uninstall iTunes before proceeding though. I'll walk you through the process I followed, if you like you can jump straight to the Solution section.
Problems:
The initial error during the installation of iTunes was:
An error occurred during the installation of assembly 'Microsoft.VC80.CRT,version="8.0.50727.4053",type="win32",publicKeyToken='1fc8b 3b9a1e18e3b",processorarchitecture="x86". Please refer to Help and Support for more information. HRESULT:0x8007054F
The error (after installing iTunes) when trying to run iTunes was:
Apple Application Support is required to run iTunes. Please uninstall iTunes, then install iTunes again. Error 2 (Windows error 2).
After trying various fixes around the forums I came across this MSKB article, which relates to the first installation error:
http://support.microsoft.com/kb/2688946
This lead me to trying to install MS Visual C++ but I received the following error trying to install that:
Error 1935.An error occurred during the installation of assembly ‘Microsoft.VC80.ATL,type=”win32”,version=”8.0.50727.762”,publicKeyToken=”1fc8b3 b9a1e18e3b”,processorArchitecture=”amd64”’. Please refer to Help and Support for more information. HRESULT: 0x80070BC9. Assembly interface: IassemblyCacheItem, function: Commit, component: {837BF1EB-D770-94EB-A01F-C8B3B9A1E18E}
Note: The installation of VC++ rolls back when it fails.
Solution:
Through this error I found this MSKB article:
http://support.microsoft.com/kb/946414
The Automated MS "Fix It" msi package didn’t work.
Note: Please backup your registry first (see the above MSKB article for instructions).
I opened the registry and (as instructed in the MSKB article) deleted the following keys:
HKEY_LOCAL_MACHINE\COMPONENTS\
PendingXmlIdentifier
NextQueueEntryIndex
AdvancedInstallersNeedResolving
Reboot and reinstall iTunes.
If it helps you please like this so others can find it.

SCCM 2012 Export Task Sequence fails with generic error message

We have a complex task sequence comprising of more than 50 applications\packages, 1975 drivers, 18 driver packages etc etc. Its long, it's big and it will not export with it's content.
We have several environments for development test and live. I am attempting to export the primary task sequence with all it's dependencies from live so that I can port it over to a new development environment.
I can export the zip file without content and it comes to 92Mb in size. The entire task sequence software set is 50Gb+. When I attempt to export with all dependencies and content the process gets about 60% of the way through and fails with the error
"Error: The filename, directory name, or volume label syntax is incorrect"
Googling the error roughly defines the problem as 'the export process cannot access the defined source path for one of the dependant items'
I wrote a PowerShell script that looks as every application, package, driver, driver package, boot image, os image and software update package in the entire SCCM software library and verifies that each and every package has a valid UNC source directory
that can be reached using test-path.
I also wrote another tool that parsed the entire source software library on the server looking for permissions errors (permissions on the structure set at a directory level rather than inherited), directories that were too long, inaccessible or otherwise
blocked, nothing was found.
It will take a very long time to go through and check each and every dependency by hand - time I do not have at present.
I looked in the TaskSequenceProvider.log as that is supposed to contain messages from the export process and found the messages in there far too high a level to use
=======================
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:00:41.161-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="exterror.cpp:128">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.ExportXml]LOG]!><time="13:00:42.339-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.ExportXml]LOG]!><time="13:00:42.341-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:00:42.341-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="4168" file="exterror.cpp:128">
<![LOG[[1AFF658 PID:3500] Received shutdown request from WMI]LOG]!><time="13:01:36.036-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="5592" file="wmiprovider.cpp:399">
<![LOG[[1AFF658 PID:3500] Initializing provider for namespace root\sms\site_P01]LOG]!><time="13:02:36.550-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068"
file="wmiprovider.cpp:90">
<![LOG[[1AFF658 PID:3500] Initialization of provider for namespace root\sms\site_P01 succeeded]LOG]!><time="13:02:36.551-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1"
thread="7068" file="wmiprovider.cpp:107">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.LoadFromXml]LOG]!><time="13:02:36.554-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.LoadFromXml]LOG]!><time="13:02:36.558-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:02:36.559-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="exterror.cpp:128">
<![LOG[[PID: 3500] Invoking method SMS_TaskSequence.ExportXml]LOG]!><time="13:03:05.428-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:333">
<![LOG[[PID: 3500] Done with method SMS_TaskSequence.ExportXml]LOG]!><time="13:03:05.431-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:352">
<![LOG[Setting status complete: status code = 0x0; ]LOG]!><time="13:03:05.431-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="exterror.cpp:128">
<![LOG[[1AFF658 PID:3500] Received shutdown request from WMI]LOG]!><time="13:03:36.369-60" date="08-26-2014" component="TaskSequenceProvider" context="" type="1" thread="7068" file="wmiprovider.cpp:399">
====================
Is there any way of increasing the log verbosity? I need to see what item is causing the export to fail.
Is there another log containing the information about the export & what it is doing?
All out builds that use the task sequence complete successfully, we can edit the sequence fine, make changes etc. so no internal corruption we can find.
Any ideas?

Torsten, smsprov.log did indeed prove useful, I could see every package as it was validated. Unfortunately the log was wrapping about every 4 minutes and it takes 3+ hours for the task sequence to reach the fail point so I still cannot see the offending
package as it wraps before I can get to the log.
I will increase the size of the log and see if I can maintain some details to investigate.
There was nothing of note in the event logs, certainly nothing leading me to suspect that WMI might be reaching its limits.
I will keep looking for the cause and will post here when I find it <= positive thinking :)

Console errors "Verification failed with 1 errors" and when Deleting Overrides

Hi Guys,
When trying to delete an override for a unix server I was prompted with this error:
Note: The following information was gathered when the operation was attempted. The information may appear cryptic but provides context for the error. The application will continue to run.
: Verification failed with 3 errors:
Error 1:
Found error in 1|XXXXX.XX.Unix.Management.Pack|1.0.0.0|DisplayString,ElementReference=a27e1d14-8ad4-56fb-da46-0c0994054e92,LanguageID=ENA|| with message:
Element Info with Identity DisplayString,ElementReference=a27e1d14-8ad4-56fb-da46-0c0994054e92,LanguageID=ENA refers to an invalid sub element Filter.
Error 2:
Found error in 1|XXXXX.XX.Unix.Management.Pack|1.0.0.0|DisplayString,ElementReference=ef78d342-5a82-d629-224d-2e476003f6e1,LanguageID=ENA|| with message:
Element Info with Identity DisplayString,ElementReference=ef78d342-5a82-d629-224d-2e476003f6e1,LanguageID=ENA refers to an invalid sub element Filter.
Error 3:
Found error in 1|XXXXX.XX.Unix.Management.Pack|1.0.0.0|DisplayString,ElementReference=06522f67-c195-2dfa-c310-a0134b961fc4,LanguageID=ENA|| with message:
Element Info with Identity DisplayString,ElementReference=06522f67-c195-2dfa-c310-a0134b961fc4,LanguageID=ENA refers to an invalid sub element Filter.
: Element Info with Identity DisplayString,ElementReference=a27e1d14-8ad4-56fb-da46-0c0994054e92,LanguageID=ENA refers to an invalid sub element Filter.
I then exported the MP and manually deleted the Override but when I try to import it I get the same error.
I have also checked a couple of other unsealed MP and some are also affected.
I have gone through the MP XML can find no matches for any of the references. Is there a way (powershell or SQL query) where i can identify what these references are or how I should proceed to troubleshoot this issue?
Cheers,
Martin
Blog:
http://sustaslog.wordpress.com
LinkedIn:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Hi Yan,
That was my understanding about the error also but there are no entries for:
ef78d342-5a82-d629-224d-2e476003f6e1
a27e1d14-8ad4-56fb-da46-0c0994054e92
06522f67-c195-2dfa-c310-a0134b961fc4
in the management pack at all.
What also is curious is that the errors refer to "LanguageID=ENA"
but the only language code present inside the management pack is ENU.
The fact that there is no ENA language pack and that there are no references matched leads me to believe
that this issue is not due to this MP its references in another.
</LanguagePack>
<LanguagePack ID="ENU" IsDefault="false">
<DisplayStrings>
There are also about 14 reference management packs this MP uses and those MP would also have a handful each which makes it difficult to troubleshoot.
Unfortunately deleting the MP isn't an option as there is a significant amount of configuration saved in it.
Any ideas on how I could identify theses references?
Cheers,
Martin
Blog:
http://sustaslog.wordpress.com
LinkedIn:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Create Master Data with leading zero

Dear Expert,
Our customer request to create Customer Master/Vendor Master/Material Master with leading zero. For example: they want to create Customer 0234578.
I can do that for material, would you please advise how to do the same for customer/vendor?
Thanks you,

Dear Mr.
Our customer number is in numeric, then this error happen. If customer number constants 1 char, then system will keep zero leading (ex: 012A4) But if customer number constants only numeric, even i type zero, system will remove leading zero.(01234 ==> 1234)
Please help.

Mateiral no. with leading zero

Dear Experts,
My case is that I created a material with ext no. assignment e.g. 1234 via BAPI without leading zero. In OMSL, the 2 checkboxes do not check anyaway.
I check it does exist in MARA, MARC and store with leading zero.
But I try to display MM03 for that material and enter 1234, the error says "The material 1234 does not exist or is not activated".
I check that in debugger mode, there is leading zeros added for that material whcih leads to this result.
Do you know how to solve it?
Thanks.

Hi dear,
Note the following
1.Lexicographical Indicator: - The appearance of the material no on the front end is governed by this indicator. This indicator is relevant only for numeric material numbers either internally or externally defined.
2.If the Lexicographical Indicator is not set (indicator is not ticked) incase of external material number assignment, the material numbers are stored with leading zeros. i.e. pure numeric material no 5007453 may look like 0005007453 if the material no length maintained as 10.
3.If the Lexicographical indicator is set (indicator is ticked) incase of the external material number assignment, the material numbers are not stored with leading zeros. i.e. pure numeric material no 5007453 will look like as 5007453.
4.If the Lexicographical indicator is set (indicator is ticked) incase of internal material assignment, the material numbers would be padded with leading zeros
5.This indicator can not be changed once there are numeric materials numbers in the system.
6.Leading zero indicator: - Along with Lexicographical indicator there is leading zero indicator on the same screen. If the indicator is set (ticked) material number is shown with leading zero, but if the Lexicographical indicator is ticked leading zero indicator is ignored by the system.
5007453     Material no length 10    External No range   Indicator Not ticked     Result   0005007453
5007453     Material no length 10    External No range   Indicator Ticked     Result   5007453
5007453     Material no length 10    Internal No range    Ticked Ticked     Result   0005007453

FTP Directories with leading space report as empty

FTP Directories with leading space in the name report "550/No such file/directories" when clicked-on. Works fine in IE and Chrome.
== URL of affected sites ==
ftp://index.storsys.ibm.com/tivoli-storage-management/

See [/forum/1/609513]
That is a problem with some IBM servers.
[https://bugzilla.mozilla.org/show_bug.cgi?id=543805 Bug 543805] – FTP list parse error when list returns twice space between date and file name
A workaround is this bookmarklet:
<code>javascript:(function() } alert(j);})();</code>

Partition my HD with Lion but it comes up with an error"

I'm trying to partition my HD with Lion but it comes up with an error" couldn't modify partition map because file system verification failed.
i have verified permissions and repair them all check out good. Any ideas?

Ok try this.
Get a copy of your users file data folders (Music, Docs etc) off the machine onto a storage drive and disconnect it.
Do this in addtition to TimeMachine or clone backups, you need to have two copies and TM drives are not quite as easily accesible and can get corrupted.
1: Boot into Recovery HD (hold command and r keys down) and use Disk Utility to First Aid >Repair the drive, see if that works if it can't repair the drive, you have a more serious issue. If it does repair the drive, do it again until nothing is repaired.
2: Next use Disk Utility to Erase Free Space with Zero option on the Macintosh HD partition, this will map off bad sectors as DU will check the file it created for errors.
(#1 and #2 here fixed my issue trying to create a partiton when DU failed.)
3: Try to create your new partiton again, I suggest you use the BootCamp software partitoning portion as it's drop dead easy and you can later use Disk Utility to change the format from MSDOS to something else, like OS X Extended for installing OS X or whatever format you require.
Or by Windows 7 installer which will change the format to NTFS for boot Windows in BootCamp.
Drives, partitions, formatting w/Mac's + PC's
https://www.apple.com/support/bootcamp/
If DU doesn't repair the drive, next create a Recovery USB following these instructions and option key boot off of it and run Disk Utility on the entire drive to repair it.
http://osxdaily.com/2011/08/08/lion-recovery-disk-assistant-tool-makes-external- lion-boot-recovery-drives/
If you can't repair the drive, your going to have to use Disk Utility on the USB to Erase with Security Zero Erase, (that's one step from the right selection), the ENTIRE drive (select the drive makers name and size on the right).
This will rebuild your partiton map (which can only be done booted from a external source) and fix your entire drive of bad sectors.
Now use the USB to reinstall Lion and Recovery from Apple's servers, you will need your AppleID and password, plus a fast relaible Internet connection.
Next install your iLife by reading here
https://support.apple.com/kb/HT4718
Install your programs from original sources and create accounts with the same name, then return files from the storage drive you made earlier.
You can read about bad sectors on hard drives here
Reducing bad sectors effect on hard drives

Powerbook 1400 bus error (with extensions) error type 10 (without ext.)

i have a powerbook 1400. bus error (with extensions) error type 10 (without extensions)
no cd. floppy is dead
the computer i put os 9 on it was a friend's 3400 witch is dead. i will see if i can get his hd.
there are no pc cards in the slots and it has os9 so removing all the ram possable including the factory ram (i only have 16 mb noram in the expansion slot eather) it will not boot. (sad mac)
the 1400 is my favorite computer
I only have a dead pb 165 (no video only sad mac sounds) and a dell (i dont like pcs so i really need to get the 1400 working) and the dell has a very bad keyboard. it likes to repeat keys alot
powerbook 1400cs/117 Mac OS 9.0.x i want a newer mac

macintosh lover
It isn't what you believe that you need in the Mac so much as what its ROM tells the 1400 that it should have. Its software is integrated with what the Mac 'thinks' of itself as being, whether you use video mirroring, HDD spindown, persistent RAM Disk or any other feature that applies to PBs rather than to DTs. Why handicap the machine by omitting parts of its persona? It will be less stable, be given to unpredictable episodes of petit mal, and be downright unreliable as a result, especially if it also lacks the physical parts of its person that you mention. That is why it needs a System for its kind of PowerBook.
Grant has outlined the best method of getting a handle on the PB, which will be much aided by its having a working HDD, a functional trackpad and so on.
Apple IIe; 68K: 11DT + 4PB; PPC: 5DT + 3PB; G3: 6DT System 6.0.8 to OS 10.4.x

Does Tecra R940-1H support external resolution 2560x1440

Hi
I use a laptop TECRA R940-1HP
I want to buy professional monitor Phillip 272P4QPJKEB/00 with a resolution of 2560 x 1440.
Please write to me.
Can my laptop support such a resolution?

The external resolution support depends on the graphic card which is built in the notebook.
As far as I know the Tecra R940-1HP supports the Intel HD Graphics 4000 chip.
From my knowledge this Intel HD 4000 chip supports max resolution of 2560x1600/32bit via Display Port.
I guess more details about Intels own graphic chip you will find on Intel page.
Greets

Tecra R940-S9421 Repeating Beep sounds like a buzzing noise

I have an intermittent issue where the Tecra R940-S9421 will begin a buzzing noise which comes thru the speakers.
I thought I had a hardware issue at first but when I muted the sound the buzzing dissapated.
So I googled the issue and found a fix whereby I must go to Device Manager / View Hidden Devices / go to Non plug and Play Items and uninstall the BEEP entry ---- this has worked for now just hoping it will not come back .....
Is this a known problem with Tecra ? Anyone else with the issue that knows a more permanent fix ?

Look at my other posts I've made about this issue. I am having the same problems. I wish apple would say whether this is a fault or if it is supposed to be this way.
http://discussions.apple.com/thread.jspa?messageID=10406601&#10406601
Message was edited by: Pmerrill87

Tecra R940 Screen

I am now considering change my Tecra M5 with Tecra R940 model. But I cannot find the one thing. Is the screen of Tecra R940 glossy like other satellite model or as same as Tecra M5? If it is glossy screen, I have to give up to buy.
Thanks

This is what I can tell you that may be of at least a little help. I bought my son a Tecra R840 about 18 months ago, and it came with a matte (not glossy) screen. I have recently ordered a number of Tecra R950's for my office, and although I haven't received them yet the specification indicates that they will come with matte (not glossy) screens.
By coincidence, the R950's are replacing Tecra M5's in my office . . .

Tecra R940-1EE - dead with lead error 4Eh

Similar Messages

Maybe you are looking for