Tecra S2 - Lan Controller is disabled after FritzCard PCMCIA installation

My Notebook is a Tecra S2.
After a FritzCard PCMCIA v2.0 is plugged in, the Lan Controller is disabled.
Not before the FritzCard PCMCIA is removed and the S2 is re-booted, the LAN Controller can be re-activated.
The LAN-Controller is identified by the device manager as an "Marvell Yukon 88E8053 PCI-E Gigabit Ethernet Controller". I tried the latest drivers, for the AVM FritzCard as well as for the Marvell Yukon.(1.the original Toshiba LAN Driver from the recover-CD, 2.the latest driver from the Toshiba Support download page and an driver, offered by the Marvell-Web-Site).
All combinations are causing the problem mentioned above
Need a solution !!!
Regards
Ronald

Hi Ronald
I have no much experience with FritzCard but a friend of mine told me that if someone use this card it is very important to install the provided software before the card can be used. I am pretty sure that there must be some manuals how to install the card properly.
The another thing is that the both devices use the same resources (IRQ).

Similar Messages

Tecra S3 - Wlan does not work after Win XP installation

Hello everyone,
I have recently purchased a Tecra S3 PTS30E-0TL059GH without operating system.
I've installed WIndows XP professional.
Everything works, except for the wireless lan. I can switch it on, but it doesn't seem to find the right drivers.
The device manager states problems with the networkcontroller and two other unknown devices.
I've installed all drivers from the toshiba website, but it still won't work.
Any help is appreciated!
Thanks!

Hi
I think the notebook supports INTEL 802.11 B/G WLan card but I'm not 100% sure about that...
In my opinion you should try to identify the WLan module.
How to do that?
In such case the usage of the PCI database should be very helpful.
More details here:
[How to identify an unknown device (e.g. Wireless LAN module)?|http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78]
Knowing the exact WLan specs, it should not be a big deal to get the right driver.

Photoshop cs5.1 icon is disabled after a successful installation

I have a brand new Photoshop CS5 Extended version for Mac (MacBook Pro), academic version. I have the serial number and Photoshop cs5.1 was successfully installed.
But after installing it I am not able to open the program as the icon is disabled.
I get the following error message : You can´t open the application Adobe Photoshop CS5.1 because it may be damaged or incomplete.
I have now tried 4 times with the same result.
Any idea what I am doing wrong or how I can fix this problem?
Thanks in advance.
Greetings from Spain

There has to be something with my Mac because now I tried installing Dreamweaver CS5.5, with the same result. Everything was fine after installation, but I still can´t access the program.

Issues after changing the AP Name on Wireless LAN Controller

I recently changed the AP Name of all the Wireless Access Points in my branch office (which are all associated to the branch office Wireless LAN Controller(s)). After that I noticed that all branch office employees are unable to connect to the employee SSID. The employee SSID uses web authentication and employees are authenticated using Head Office AD via Cisco ACS, both located at the Head Office.
There are other SSID's on the WLC which all work fine, but only employee SSID which uses AD authentication does not work. AD authenticaion is working fine because employee's in HO are successfully able to connect to the employee SSID at HO.
The branch office is connected to the HO via a tunnel link. We noticed that if we restart both the ASA at either ends of the tunnel. The employee SSID starts working again but only temporarily for a day or so... what could be the issue? Can renaming the AP's cause issues? How can I fix this problem?
Thanks in advance

Thanks Elliott,
I did the debug like you said and I am getting the following debug messages:
*apfMsConnTask_0: Jun 20 08:18:14.580: Deleting the client immediatly since WLAN is changed
and also
*apfReceiveTask: Jun 20 05:25:11.857: 00:1f:3c:86:af:15 Orphan Packet from 192.168.52.34
The logging on the WLC shows
*apfReceiveTask: Jun 18 17:56:41.788: %MM-1-ANCHOR_UNAVAILABLE: mm_mobile.c:2155
All export anchors are down. Cannot anchor the client.00:c0:a8:f3:cd:ae
The DHCP pool for the employee users are configured on a guest WLC which sits behind an ASA

KT6Delta onboard lan controller freezes machine!

KT6Delta onboard lan controller freezes machine after a recently purchase of new ram.
TwinMOS PC3200 TwiSTER DDR 512MB CL2
Chip = WLCSP, (DDR-PC400MHz)
Why i believe the ram purchase is the issue, you say?
Well you see this ram model is not on the supported list on the motherboard information page to msi. allthough the 256mb model is.
so i had to manually configure the DRAM timing so that my computer would run at fsb 166 and ram at 400mhz.
But lets get back on track. Everytime i copy over the network (large files that use top network speed) the machine either freezes or i might get away with a complete network connetcion loss. so i have tried to copy at different speeds and foudn out that 2 mbyte a sec is possible without the computer hanging.
i contacted http://www.broadcom.com support base and they did not know of any simmilar issues regarding the broadcom 57x integrated network hardware. But they did say that my ram might be the issue because the network card sends its DMA packets there.
and i quote:
"Response from Broadcom: I am afraid this is not a known issue to me. But if you are saying with the different RAM this problem was not seen, this point directly to the RAM you use on this system and the compatibility issue. The RAM could for sure cause this type of the problem since the network adapter DMAs packets into and from the system memory (RAM)."
So can anyone help me? i really want to be able to use my network hardware normally and not being forced to sell my current ram chip and buy a new one.
I can't remember all dram timings options but here are those i do remember.
CL = 2.5 (yes didn't work with 2)
Row precharge time = 5
Ras pulse width = 8
Ras to cas delay = 5
-Kim

Quote
What are your temps? Freezing often happens when CPU usage makes it too hot. I believe there is a way to check CPU usage in XP...
CPU temp is around 45-52 depending on what im doing.
Quote
I have a hard time convincing myself that the symtom - the LAN - is the cause.
What do you mean? its the ram chip thats the cause for the network freeze (or at least that's where it all is pointing at).
Quote
What is your video card? ...Tell us your system while you are at it!
Here's a quick list i made on the fly.
ATI Radeon 9600PRO 128mb ram
Amd xp thoroughbred 2500+
512mb ddr ram twinmos twiser series
KT6 DELTA FISR2 or something
2*160 gb maxtor sata disks + 2*80 gb maxtor ide disks
yeah thats it.

Certificate Trust (Pinning) disabled after silent installation

When we install EMET 4.1 (MSIEXEC.exe /qb!- /i "EMET Setup.msi" ALLUSERS=1 REBOOT=REALLYSUPPRESS) and import te Popular Software.xml and CertTrust.xml settings with EMET_Conf.exe the Quick Profile Name is set to custom Security setting and the
Certificate Trust (Pinning) option is disabled. The import of the CertTrust.xml worked because the pinning rules en protected websites are visible.
How can we use the Recommended Security Settings and enable the Certificate Trust (Pinning) option after installation? I tried to use a Group Policy but there are no group policy settings for the Certificate Trust (Pinning) option.
Has someone else experienced this and how cal we solve this?
Regards,
RK

The Group Policy settings for EMET 5.0 look the same as those for EMET 4.1. The 'problem' that is the system mitigation Certificate Trust (Pinning) is disabled after a silent installation is not (yet) fixed in EMET 5.0 technical preview. On the other hand
I found out that "EMET_CONF.exe --system Pinning=Enbled" enables the system mitigation Certificate Trust (Pinning). The Quick Profile Name remains set to custom Security setting but I guess that's the settings are te same as Recommended Security Settings.
Regards,
RK

MSI 890 GXM-G65 LAN Controller Issue

Hello, Forum!
I have had this motherboard for the past few years, loved it, and then the LAN controller suddenly decided to "stop working." What I mean by that is that when I boot up, Windows loads, and then I have no network connection. I have updated the Realtek drivers, flashed the latest BIOS, disabled/reenabled drivers, renewed IP address, statically assigned an IP address, flushed DNS, installed BC Edit. The *one* thing that "solves" the problem is hitting F8 upon bootup and selecting "Disable Microsoft Driver Signature Enforcement." I'll have network connection again after that, but then it goes away upon the next boot up, so I have to do this *every* time I want to use the computer. This gets kinda annoying, especially when I do leave it on during a download from Steam or something overnight, it needs to reboot for updates or part of the install process, then it boots back up and connection is lost, so download doesn't complete until the next day when I reboot it *again* and do the F8 routine. Because I have a beast-sized graphics card and an audio card, I have no room for a separate NIC card.
Computer specs:
The aforementioned mobo in the subject line
AMD Phenom II x6 1055T
12GB DDR3 RAM
NVIDIA 550Ti 1GB
ASUS Xonar DG sound
Antec 450w Earthwatts power supply
I have been trying to Google the problem and ask people who were formerly Microsoft tech support, but this has not help. Can anyone help?

I run Windows 7 x64. I have a desktop and a laptop, both of which have had reinstalls done on them in the past (long before the LAN issue on the desktop happened), both had problems with reinstalling because it wouldn't let me re-use my product key. I then had to buy all new copies of Windows (I *really* try to stay away from torrenting). This is not a hassle or expense that I wish to go through again unless I *know* it will fix the problem.
Three things that I neglected to mention that I've tried are:
- System Restore
- Set to Last Known Good Configuration
- Installing a USB wireless adapter - that doesn't work either without the whole F8 routine.

Cisco Wireless Control System need wireless Lan Controller ?

Cisco Wireless Control System need wireless Lan Controller , for Rogue detection

Hi Joao,
The WCS is used in conjuntion with the WLC (Wireless Lan Controller) for Rogue Detection. It is not a must for this function but more of an add-on :)
The Cisco WCS is an optional network component that works in conjunction with Cisco Aironet Lightweight Access Points, Cisco wireless LAN controllers and the Cisco Wireless Location Appliance.
From this doc;
http://www.cisco.com/en/US/products/ps6305/index.html
Overview of WCS
The Cisco Wireless Control System (WCS) is a Cisco Unified Wireless Network Solution management tool that adds to the capabilities of the web user interface and command line interface (CLI), moving from individual controllers to a network of controllers. WCS includes the same configuration, performance monitoring, security, fault management, and accounting options used at the controller level and adds a graphical view of multiple controllers and managed access points.
WCS runs on Windows 2003 and Red Hat Enterprise Linux ES 4.0 and AS 4.0 servers. On both Windows and Linux, WCS can run as a normal application or as a service, which runs continuously and resumes running after a reboot.
The WCS user interface enables operators to control all permitted Cisco Unified Wireless Network Solution configuration, monitoring, and control functions through Internet Explorer 6.0 or later. Operator permissions are defined by the administrator using the WCS user interface Administration menu, which enables the administrator to manage user accounts and schedule periodic maintenance tasks.
WCS simplifies controller configuration and monitoring while reducing data entry errors with the Cisco Unified Wireless Network Controller autodiscovery algorithm. WCS uses the industry-standard SNMP protocol to communicate with the controllers.
From this good doc;
http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7270.html#wp1131195
Detect and Locate Rogue Access Points
From this WCS doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806f070a.shtml#new5
Rogue Detection under Unified Wireless Networks
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
Hope this helps!
Rob

Wireless Lan Controller Issue

Hi All,
We have a Wireless Lan Controller 4402 with software version 4.0.155.5. On Friday we experience a problem where our clients wouldn't get redirected to the internal webpage for authentication. It would just come up with page not found. We know the page was working fine becasue we could manually type in the
https://1.1.1.1/login.html and the
page would come up and you could login successfully. The users who were already connected to the controller were not affected and continued to operate. We have 2 other WLC's at the same software revision and they were not affected so I don't think it has anything to to with software level. Its like the webserver in the wlc failed to work. We failed over the AP's to the 3rd WLC and rebooted WLC1. After the WLC1 restarted we failed one of the previous non-working AP's back to it and it works again.
I know "now" there is debug commands to run at the time when the WLC wasn't working, but unfortunately I didn't know at the time. The WLC is running again fine and I was wondering if anybody has seen this issue before.
Any ideas on a fix or reason would be greatly appreciated.
Thanks,

We are running WiSM 4.1.185.0 and we just had the similar problem with one controller. The other three controllers were fine when it happened. The exactly issue was the nslookup failed(timed out) from the client, so the web login page won't show when people lunch the browser. A reboot of the controller fixed the problem. We have been running Cisco LWAPP for more than a year (from 4.0.155.5 to 4.1.185.0) and it is the first time we see this problem. TAC is still investigating the cause.
Zhenning

Error when installing webauth certificate virtual wireless LAN controller

Hi there
I am having issues installing web auth certificate for our virtual wirelesss LAN controller.
I am issuing a certificate from our own PKI in following format
device cert for WLC > Intermediate > our root cert.
I have followed the discussion here
https://supportforums.cisco.com/discussion/10890871/generating-csr-wlc-5508
and the document here
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/109597-csr-chained-certificates-wlc-00.html#support
However I am still getting the following errors
*sshpmLscTask: Jun 30 17:18:26.443: sshpmLscTask: LSC Task received a message 4
*TransferTask: Jun 30 17:18:28.785: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 30 17:18:28.785: RESULT_STRING: FTP Webauth cert transfer starting.
*TransferTask: Jun 30 17:18:28.785: RESULT_CODE:1
FTP Webauth cert transfer starting.
*TransferTask: Jun 30 17:18:33.154: ftp operation returns 0
*TransferTask: Jun 30 17:18:33.154: RESULT_STRING: FTP receive complete... Installing Certificate.
FTP receive complete... Installing Certificate.
*TransferTask: Jun 30 17:18:33.154: RESULT_CODE:13
*TransferTask: Jun 30 17:18:37.159: Adding cert (8217 bytes) with certificate key password.
*TransferTask: Jun 30 17:18:37.169: sshpmCheckWebauthCert: Verification return code: 1
*TransferTask: Jun 30 17:18:37.169: Verification result text: ok
*TransferTask: Jun 30 17:18:37.171: sshpmAddWebauthCert: Extracting private key from webauth cert and using bundled pkcs12 password.
*TransferTask: Jun 30 17:18:37.361: sshpmDecodePrivateKey: calling ssh_skb_decode()...
*TransferTask: Jun 30 17:18:37.493: sshpmDecodePrivateKey: SshPrivateKeyPtr after skb_decode: 0x2aaaacb51628
*TransferTask: Jun 30 17:18:37.493: sshpmAddWebauthCert: got private key; extracting certificate...
*TransferTask: Jun 30 17:18:37.494: sshpmAddWebauthCert: extracted binary cert; doing x509 decode
*TransferTask: Jun 30 17:18:37.494: sshpmAddWebauthCert: doing x509 decode for 1594 byte certificate...
*TransferTask: Jun 30 17:18:37.494: sshpmAddWebauthCert: failed to validate certificate...
*TransferTask: Jun 30 17:18:37.494: RESULT_STRING: Error installing certificate.
*TransferTask: Jun 30 17:18:37.495: RESULT_CODE:12
*TransferTask: Jun 30 17:18:37.495: Memory overcommit policy restored from 1 to 0
Error installing certificate.
Any help is much appreciated

Similar issue:
https://supportforums.cisco.com/discussion/11043836/wism-42112-and-web-auth-certificate

Security policy signature in Wireless Lan Controller?

Can we update security police signature in wireless lan controller ?

I made this solution andthe problem still exist. and restart the VMware and also the problem still exist
Go to Configure> Controllers
and then which controller have config mismatch...on right side click on mismatch in Audit status tab.
After that it will ask for audit now, click on that. After auditing it will show you the two option:
1. Restore PI values to Controller
2. Refresh config from controler
Clcik on 2nd #Refresh config from controler#
Then select 2nd option again(Use the configuration on the controller currently) and click on GO.
Please feed me back.

LAN controller

Dear All ,
I have Cisco Wireless LAN controller AIR-CT5508-K9 ,I had created a Web Authentication page for Guest VLAN users ,its giving the error "ERR_CERT_DATE_INVALID" when the users trying to access web-auth Page .
Kindly support me for the issue.
Thanks.,

If you haven't installed a 3rd party certificate, your guest users will see a certificate error because the wlc uses a self signed certificate. If your on v7.2, I believe that's the code this feature was introduced a, you can disable https for web auth. This way you don't get a cert error.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/115951-web-auth-wlc-guide-00.html#httpnots
-Scott

Msi p4n sli - ethernet LAN connection not recognized after reinstall

So I am reinstalling windows xp home edition after replacing a hard drive with over 1,000 bad sectors... The ethernet LAN worked just fine before reinstalling. I don't have the original driver cd, so using another computer, i downloaded the latest nforce4 chipset / ethernet / IDE / SATA drivers from the msi downloads site. Installed them and everything worked fine except that the network connection never showed up. It is not to be found in the device manager, and I don't see it when I view hidden devices. The LAN chip is enabled in the BIOS and it tried to netboot the first time i booted with the new hard drive (hadn't put the cd in the drive ). When that didn't work, I tried downloading the latest chipset drivers from nvidia's site, and the same thing happened. No local area connection!
Is there something I'm missing? is there a utility I should be installing before I install the chipset drivers, etc?
I'm feeling stressed as I need to get this finished and returned to my client today but I've been dealing with this since yesterday to no avail
Any help is appreciated! thank you!
Jeff

A little embarrassed that I didn't figure it out earlier, but I tried several things, realized I had turned off the LAN chip in the BIOS and forgot to turn it back on after installing the second time.
once i enabled it, I had to manually pick drivers for the "Other PCI Bridge Device", and then for the the nforce network controller windows found after that.
Lesson learned: stress inhibits cognitive function.

TS2446 Apple ID still disable after resetting password. What is the fix?

Apple ID still disable after resetting password. What is the fix?

Welcome to the Apple community.
If you have tried Apple's recommendation to reset your password, and it has not succeeded, then I suggest you contact Apple using the Express Lane (select your country, navigate to iCloud help and enter the serial number of one of your devices)

Wireless lan Controller 4402 / ping dynamic interface failed

hi,
i've a problem with a Wireless Lan Controller 4402.
When i configure the dynamic interface on the my network , with wired lan
i don't reach (i use the ping command) the ip address of the WLC.
In my case (wired):
On my pc i've a ip 10.1.78.1 255.255.0.0 and dgw 10.1.1.1 (vlan721)
The lan WLC have a ip of management 10.12.2.4 /24 (vlan799) [dgw 10.12.2.1]
dynamic vlan 792 ip add 10.12.78.100 / 22 (vlan792) [dgw 10.12.68.1]
i ping these interfaces (10.12.2.4 and 10.12.78.100) and the ping is ok.
When i create a dynamic interface vlan 721 starting the problem:
dynamic vlan 791 ip address 10.1.1.240 / 16 (vlan721)
After this ......the ping on 10.12.2.4 and 10.12.78.100 don't respond very well
and i lose the 80-90% of the ping packages.
through the wi-fi instead I do not have problems.
the problem exist only via wired (cable).
Can you help me?
Thanks
FCostalunga

Hello,
Pinging the dynamic interface is officially not supported. The reason why is because the controller places a very low priority on ICMP traffic. Typically, you will not have an issue with doing so on your wireless network because this interface is basically a gateway for the client. However, from the wired network - the only interface designed to respond to pings 100% of the time is the management interface. Hope this helps!
-Mark

Tecra S2 - Lan Controller is disabled after FritzCard PCMCIA installation

Similar Messages

Maybe you are looking for