Tecra S3 - Wlan does not work after Win XP installation
Hello everyone,
I have recently purchased a Tecra S3 PTS30E-0TL059GH without operating system.
I've installed WIndows XP professional.
Everything works, except for the wireless lan. I can switch it on, but it doesn't seem to find the right drivers.
The device manager states problems with the networkcontroller and two other unknown devices.
I've installed all drivers from the toshiba website, but it still won't work.
Any help is appreciated!
Thanks!
Hi
I think the notebook supports INTEL 802.11 B/G WLan card but I'm not 100% sure about that...
In my opinion you should try to identify the WLan module.
How to do that?
In such case the usage of the PCI database should be very helpful.
More details here:
[How to identify an unknown device (e.g. Wireless LAN module)?|http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=78]
Knowing the exact WLan specs, it should not be a big deal to get the right driver.
Similar Messages
-
Tecra M10-10z - 3G does not work after Win 7 installation
Tecra M10-10z I have installed Windows 7 pro 64bit
Everything is configured correctly, but connection 3G does not work: the message is " no network"
with Windows XP is ok.
I did not find firmware updates or similar.
Is there someone who can help me?
tksHi
In order to use the 3G you should firstly check if the 3G ericsson module was properly installed.
In case there is an yellow exclamation mark visible in the device manager, the 3G driver should be reinstalled.
I found on the Toshiba EU driver page:
[Ericsson 3G Win 7 driver|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=5&selSeries=148&selProduct=813&selSho rtMod=null&language=13&selOS=30&selType=295&yearup load=&monthupload=&dayupload=&useDate=null&mode=al lMachines&search=&action=search&macId=&country=all &selectedLanguage=13&type=295&page=1&ID=71930&OSID =-1&driverLanguage=42]
Furthermore ensure that the 3G RF Power Control Utility has been installed properly.
The 3G RF Power Control Utility" activates your 3G on startup.
This tool can be found here:
[3G RF Power Control Utility for Win 7 64bit|http://www.toshiba.eu/innovation/download_driver_details.jsp?service=EU&selCategory =2&selFamily=5&selSeries=148&selProduct=813&selSho rtMod=null&language=13&selOS=30&selType=322&yearup load=&monthupload=&dayupload=&useDate=null&mode=al lMachines&search=&action=search&macId=&country=all &selectedLanguage=13&type=322&page=1&ID=73658&OSID =-1&driverLanguage=42]
Hope the 3G network would functions after the reinstallation of both tools. -
Tecra M7: Tablet does not work after lid closing
Has anyone had problems with the tablet not working after closing the lid on a Tecra M7? Bios is 3.20
Doesn't seem to happen on hibernate or sleep.
I have the lid set to do nothing on close.Hi
What do you mean with tablet not working after closing the lid?
Does the notebook freezes or what?? What happens exactly???
The close the lid settings can be set to hibernation mode or standby mode or no action.
These settings can be set in the power saver setup actions.
If you have some problems with some installed Toshiba applications I would recommend reinstalling the TOSHIBA Common Modules and the program which doesnt run correctly!
Best regards -
CD/DVD drive does not work after Win 8 intsallation
from a month i've updated my windows into windows 8, everything is working great but the DVD-RW .
When i put empty cd and try to open it, it gives me error while opening saying:
"windows was unable to complete the format"
So is that a software or a hardware problem?!
waiting for the help !Does this mean that your CD/DVD drive does not work anymore and is not recognized by system?
If yes, then I would recommend checking this Toshiba document which I found on the knowledge base portal webpage:
+Why does my CD/DVD Drive not work after upgrading to Windows 8?+
http://aps2.toshiba-tro.de/kb0/FAQ2B03F10002R01.htm
You will need to uninstall the Toshiba programs:
TOSHIBA Recovery Media Creator
TOSHIBA Disc Creator -
Print Spooler does not work after Win 8.1 install
I upgraded several computers to Win 8.1. Most are operating normally and do not have this problem. This is relevant to show that it is not a printer hardware or compatibility problem. On one computer, the print function is not working.
I've tried reinstalling printers, getting new drivers, etc. It comes down to this. An active (connected) printer is selected and print test page is selected. The dialog box says that the print queue is full. I went to the queue subdirectory
and deleted all files, no change to the results. The Print spooler is active in task manager. Stopping and restarting the print spooler makes no difference. Any ideas?I had similar problems with HP Printers on the LAN (after upgrade from Windows 8 tot 8.1
32bit)
HP Laserjet 4000 Laserjet 4050 and Laserjet 4250 - all with Network interface.
Erratic behaviour: inserting blank pages, no duplex printing, programs stalling when printing etc…
Printers and network are fully functional and work perfectly with W7 and XP. Not with Windows 8.1.
Strange thing: Epson Aculaser and Ricoh Aficio 3224 worked fine but those were installed after the Windows update.
So definitely something with the Microsoft drivers for the HP Laserjet printers.
After a few installs and uninstalls of the HP printer drivers the problems stayed.
Then I removed all HP related driver files (C:\\Windows\\system32\\spool\\PRINTERS")
and all references in the Register because the standard uninstall of the drivers did not remove all files.
-> First uninstall ALL HP printers (laserjet, deskjet, officejet etc ..)
-> Then look in
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Drivers]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\Windows NT x86\Print Processors]
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers]
Make a backup of the registry keys and then remove all files starting with hp….
Remove the print processors starting with hp
(i.e. hpzpplhn.exe)
Then restart your system.
Reinstall the printers, they should be OK now.
If you still have duplex printing problems : replace the hpzpplhm print processor with the winprint processor. (may give other limitations, google for more info).
In my case this solved the erratic printing problems. -
Satellite L305D-S5881: Touchpad and FN keys do not work after Win 7 installation
I have recently installed windows 7 and all of a sudden yesterday my touchpad did not work.
I was not able to move my mouse arrow at all.
I had to purchase a wireless mouse so I could use my laptop.
When I press the fn key plus f9 nothing happens to see if it is enabled or disabled.
I have a satellite l305d-s5881
thanks for your helpHi mate
The Satellite L305D-S5881 belongs to the Toshiba US series and has been released for US market.
You will need to visit the Toshiba US driver page in order to get all drivers.
To get the touchpad working, you will need to install the Touchpad driver.
Furthermore the FN buttons are controlled by VAP (value added package) and Flash Card Support Utility.
You need to install both; firstly VAP and then Flash Cards.
Here is the Toshiba US page:
http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/home.jsp
Greets -
Satellite M70-394: WLan does not work after wake up from standby
Hi all....
I have a problem with my WLan connection and hope one of you may be able to help. Starting my computer from off there isn't a problem with the WIFI connection but if I put the computer into standby by closing the lid and then restarting it from there the light comes on briefly for wi fi but then goes off and the only way I can connect is through a cable.
Any suggestions would be gratefully appreciated.Hi
I have read in the forum that some similar "Wlan standby" issues were fixed by BIOS update.
I think you should compare the BIOS version on the notebook with the BIOS which is available on the website. If there is a new update try to upgrade it
Be sure that you have chosen the right BIOS. -
"Find Resources" does not work after Application Builder Installer
I use Lv Full 6.1 / Appl.Builder 6.1
VISA:"Find Resources" acts properly as long as a built application is installed on a PC that has LV installed.
as soon as only the runtime eng. is installed no resources are found.
Who helps?Thank you Dennis for your reply. I tried to install the VISA runtime engine via the "Run executable after installation" but it appears to run the Visa-runtime-engine-installer before ending the application installation. So I had to run that installer manually. Nevertheless you pushed me in the right direction.
THANKS -
Amd video drivers not working after win 10 upgrade
AMD video drivers not working after win 10 install. running on microsoft basic driver, call hp smartfriend assistance. appearently there is a fix but hp will not help unless i pay 100.00$ US because the warranty has expired on my notebook.Have a pavilion dv7 was running AMD Mobility Radeon HD5000 series. Thank you hp will not be purchasing an hp product again. Alienware here i come.
Not much we can do since your model is not supported by Toshiba for Win 10 upgrade according to THIS list so there is no Win 10 driver for your TouchPad. That button, however, is not the only way to disable/enable the TouchPad. FN+F9 does it and you can fix it where, when you plug in an external mouse, it will automatically be disabled.
-
Card slot does not work after update (14/10/2011)
Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
MacBook Pro 13 OS ver. 10.6.8Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks
-
My Hot Spot does not work after update to 6.0.1. Any suggestions?
Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal. -
Click to activate does not work after update
Click to activate plugin does not work after updating to version 23.0.1
hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.
-
WiFi iPhone 4S does not work after update iOS 6.0
WiFi iPhone 4S does not work after update iOS 6.0
This sounds more like a hardware issue.
Have you checked that the dock connector port is not dirty? -
Flash player does not work after I installed it
Flash player does not work after I installed it
I'm using Mac Osx and my browser is Safari
Date: Wed, 5 Feb 2014 00:41:29 -0800
From: [email protected]
To: [email protected]
Subject: Flash player does not work after I installed
Re: Flash player does not work after I installed it
created by Mike M in Installing Flash Player - View the full discussion
This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
What OS are you using?
http://mmonlinedesigns.com/images/os.png
What browser?
http://mmonlinedesigns.com/images/browsers.png
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Installing Flash Player at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0. -
My sound system does not work AFTER installing pc to tv wireless connection
my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.
Hi,
You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
one used by the Form contact for Form Invoice.
Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
VS General Question forum mainly discusses
the usage of Visual Studio IDE such as
WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
System and Visual Studio Editor.
Thanks,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.
Maybe you are looking for
-
Photoshop CS6 won't launch. Unexpected and unrecoverable problem.
I am unable to launch Photoshop CS6 on my 2012 Macbook Pro running OSX Mavericks. Everytime I attempt to launch it I get a message saying "An unexpected and unrecoverable problem has occurred. Photoshop will now exit." I have already reset the applic
-
SQL Developer 3.0.02 & External table
Hello all, I encountered an interesting error while working with SQL Developer. I created external table mapped on data file in csv format. Everything works fine up to moment I double clicked the table header of the first column to make data sorting.
-
Need adobe flash for power book g4 OS X 10.5.8
need adobe flash for power book g4 OS X 10.5.8
-
Hello I was hoping someone may be able to help me with a problem I have been having and unloading external .swfs, Ill try to explain this as best I can. I have two .swf files, both of which are connected to an external .as file. One is the main, the
-
Is there a workaround that i can create the xml file outside the database server?