Tecra T9100, XP, Stand By doesn't work

I've a Tecra 9100 with XP pro.
When I click on "Turn off computer", I get a pop-up with 3 buttons: Stand By, Turn Off, Restart
The "Stand By" button is grey (disabled)
So far:
I've checked the Control Panel, Power Options
I've upgraded the BIOS from 1.3 to 1.6
According to a post in this forum:
" Try to reinstall the Toshiba Power saver.
I'm not 100% sure if it will help but this Toshiba software is responsible for the hibernation and standby mode."
So, I've installed the " Power saver", but had first to install the "Common module".
Still no result
Any hint please ?

Hi Jack Black,
Thank you for the tip
> The Toshiba power saver is responsible for the stand
> by and hibernation mode.
OK
> But if you have installed this software properly
I think so. In Control Panel, Power options, all is grey and the new applet, Toshiba Power is there and working
> you should use the FN+F3 key combination to go into
> stand by mode.
It doesn't do anything
> I dont know if you have installed your OS manually
Yes, manually, from CD
> with the Toshiba recovery CD all options should works
> properly.
Too late for the recovery CD :-(
Any other Toshiba software that I should install ? (besides Common modules and Power Saver)
I expected to find something in BIOS about enabling power options, but didn't see it.

Similar Messages

Stand activity doesn't work with standing desks (oh the irony)

I use a standing desk and normally stand from 9am to 2:30 every day (sometimes all day). Today I've worked with my hands on my keyboard from 9-2 and watch only thinks i've stood for 2 hours - the times that I went to the bathroom and when i went to get lunch. I suspect that L shaped hands up desk posture is considered "sitting" by watch when the irony is that i'm at a standing desk the whole time. Pretty hard to tell I guess but wow ironic that as one of the people who has been standing at work for a long time that I'm unlikely to ever meet my standing goal (guess 12 minutes beats 8 hours of standing according to apple watch - doh!)
Anybody else seeing this issue?

I am having the same sort of problem. My apple watch is giving me a minute for standing when I am actually sitting. Also at times when it reminds me to stand I stand for 5-10minutes and it doesn't alert I have done so. Unfortunately it makes you question the "exercise/activity" function that the watch is supposed to be measuring.

Tecra S11-15T - GPRS modem doesn't work on internal USB port

My GPRS moden only works when I plug it into the dockingstation's USB port or if I use a USB port hub. If I plug it directly into the USB port on the laptop, I get an unknown device displayed in the device manager.
I have tried re-installing the chipset of my Toshiba Tecra S11-15T. I cannot get the device to work directly from the laptop's USB ports. I have WIN XP Professional.

Hi
Maybe the USB port does not provide enough power to get the modem working.
But all ports support the USB standards and every USB port is able to provide 500mA.
Possibly the modem needs more.
You can try to disable the USB power saving option.
In device manager, click right on USB root hub and go to Properties.
Then choose Power Management tab and uncheck the option; Allow the computer to turn off this device to save power

Tecra 9100: Headphones out doesn't work

at my Tecra 9100, the Headphones connector doesn't work. The internal speaker do well. If i plug in headphones or external speakers, the internals are being switched off, but at the external devices i can't hear anything.
My soundcard generally works, i thought there could be a chance to fix this just by dis- and reconnection the wire/board from the front connectors to the sound board ... but i've never done any technichal stuff at a Tecra, so it would be nice if someone could give me some input how and where i would have to open it, and if this is even a chance to fix my problem.

Hi
According to your problem description I presume that Audio headphone port is defective. There is small switch that switch between internal and external speakers.
I have the same unit and it works well on my unit. I am afraid that you must contact service partner and check this mechanical connector.
Bye

Stand-by button on Cinema HD display doesn't work after Mountain Lion upgrade

Hi,
After I upgraded my Mac mini (spring '09) to Mountain Lion it appears that the buttons on the side of my Cinema HD display doesn't work. There is a setting in sys preferences that should put the Mac in stand-by when the power button is pressed. This doesn't work after I upgraded to OSX 10.8 Mountain Lion.
Does anyone have similar experience. Anyway to fix it?
Thanks,
Henrik

Have done some further investigating (to no avail). The TV is displaying in my system Info as follows:
Intel HD Graphics 3000:
Chipset Model: Intel HD Graphics 3000
Type: GPU
Bus: Built-In
VRAM (Total): 384 MB
Vendor: Intel (0x8086)
Device ID: 0x0116
Revision ID: 0x0009
Displays:
Color LCD:
Display Type: LCD
Resolution: 1440 x 900
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Connection Type: DisplayPort
TOSHIBA-TV:
Resolution: 1920 x 1080 @ 60 Hz
Pixel Depth: 32-Bit Color (ARGB8888)
Mirror: Off
Online: Yes
Rotation: Supported
Television: Yes
But nothing on the screen.
Does anyone know if Apple have banned certain screens????

My new iPhone 4 doesn't work at all

You are definitely not alone with your issues. I'm on my second iPhone 4 unit, and am still having the same problems. I've had proximity sensor insanity, battery draining after 8 hours of stand-by (NO USE, just sleeping) to the point that my phone goes into a coma and has to be plugged in to be revived, the grip of death dropping calls....
But the single most irritating and infuriating problem is the signal strength/reception fluctuation. I share a house with two iPhone 3Gs users, and I had an original silverback iphone until July 2010. They all work fantastically well with no issues when I'm at home (where I am just about 24/7, since I work from home). *_My new iPhone 4 doesn't work at all.*_. Signal strength is all over the place. I did a test where I sat watching the bars showing signal strength for five minutes. In that time, I saw it switch from E (edge?) with full bars to 3G with full bars to 3G with 1 bar to 2 bars to 4 bars to 1 bar to "Searching." Then back to 3G, with degradation of bars from 3 to none, then E network appears again, this time with full strength. This all with the phone sitting on a table, not being touched by human hands.
It seems that my iPhone is constantly switching actual physical networks, and as a result signal strength is all over the place from one 30 second period of time to the next. This drains the battery like crazy, and means that all incoming calls go to voicemail--usually without my phone ever ringing.
The 3G phones in my house work great. The 1st G iPhone I have had since the week it came out worked great (though its battery doesn't hold much of a charge anymore, after three years). On my new IP4, games are awesome. The videos and photos are amazingly clear and high quality, and editing on the phone is out of sight. iPhone Apps rule. MobileMe syncs my contacts quickly and easy. The only thing I love more than the iP4 features is my iPad--it rocks.
Everything works on my IP4 at home BUT THE ACTUAL TELEPHONE FUNCTIONS. This is unacceptable. In late August, after two weeks in which I had 4 minutes of phone use, the nice folks at the Apple store switched me to a new phone, no questions asked. The phone worked so much better, I could send texts and place calls most of the time (this was now the first part of September)...except that now that I was using my IP4 to make phone calls, I started having a problem with the proximity sensor during those calls. I'd be talking and my cheek would mute the phone, turn on speaker, open contacts and edit info (with gobbledygook), and of course, hang up on people.
So around Sept. 18 I was told by Apple phone support to update to iOS 4.2, restore as new, and do two complete power up and drain down cycles. This would fix the proximity sensor and any other issues.
Well, I would love to see if iOS 4.2 actually did fix the PS, but I can't get the signal strength to stabilize long enough to have an actual phone conversation. I'm back to watching the signal strength go up and down at random (with me touching/holding it carefully to avoid grip of death, and also when I leave phone on the table with screen lock off --no touching). It is back to switching between E network and 3G and varying strengths of wi-fi from my home network. This eats up battery from 100% to low enough to turn off in under 10 hours of standby (usually 6-7). Essentially, my IP4 is back to being unusable as a phone.
So I did another long, involved call to Apple tech support on 9/18. They tell me that I have to turn off wi-fi, turn off 3G, turn off push/fetch and notifications, shut all apps (no multi-tasking) and do everything but switch my phone to airplane mode--and see if the battery holds up for 24 hours in standby. If that didn't work, I should restore from new, but not load any contacts or network or data or anything--just leave it as it would be out of the box new.
As a test, I turned everything off as advised: 3G, wi-fi, push, etc. Now my battery life is back to normal, where I can have the IP4 on stand-by for up to two full days before needing a recharge. Fabulous. BUT IT'S NOT A SMART PHONE if I have to turn off 3G, turn off wireless, and not use email push and so forth.
I'm so frustrated I could scream. I'm quickly coming to the conclusion that there is a significant flaw in the new iPhone. Or perhaps it is just an issue for iPhone 4 users in areas where the signal strength is marginal, or where there are two types of overlapping network coverage (E and 3G in my case). I know that the networks themselves are in good condition--though I'm in a semi-rural area, the state capital is 4 miles away, and I know they have a new tower and good coverage for the politicians and power brokers around town. The phone coverage area I live in has Edge network in the south part of the network area and 3G in the north part, which is the state capital. I'm right in between. Could this be the problem? AT&T says no, it's Apple's fault.
Message was edited by: HighSierra

So what to do besides complain? Troubleshoot?
I just wonder if all of us who have had chronic signal strength and "Searching for network" issues that totally drain the battery might have something in common, despite being all over the world? I'm using wi-fi 95% of the time, and live in a semi-rural area with overlapping networks run by same carrier. Apple folks hinted that maybe in my area the network usage is nearing capacity (resulting in getting kicked off of 3G and down to E as new calls are placed that strain capacity). They also hinted there could be interference from mountains or other objects. But here's the thing--3G phones work fine, and my IP4 works fine when I'm away from home, usually in the capital city on strong 3G network. (When I say "works fine I mean the signal is good and calls go through, I haven't tested battery drain away from home yet).
I have to conclude that the problem is the IP4 itself--something about the hardware or the software (namely, the way it connects to the phone network) is horribly wrong. Other folks who live in urban areas or with strong networks that (likely) aren't over-utilized don't seem to have this issue. After reading through these pages, it also seems the wi-fi may be a major culprit in draining the battery and in varying signal strength (this is from Apple phone support, which said that varying signal strength and the constant pinging off the home wi-fi is creating a "power struggle" and keeping the phone constantly looking for the best connection option). Mind you, 3G iphones on the same home network have no problems whatsoever.
So while I'm not a technical expert, it seems like the problem HAS to lie in the differences in the way the IP4 connects to the cellular and/or wi-fi network. And since the connection/signal strength problem was "resolved" on my replacement phone, but then "broken" again by the software update of iOS 4.2, I'm leaning toward this being a software issue. I've offered to help Apple troubleshoot, and I'm trying to be patient--because the IP4 is a work of art and I've never had an issue with an Apple product before. But all they want me to do is restore, restore, reload, restore, and then drive 1 hour to the nearest Apple store (in Reno, NV) and get a new phone...and start the whole process over again. I don't have time for this, I need my phone back.
I'm this close to trading in my beautiful but flawed IP4 for a 3G. Maybe I should just get a new battery for my original iPhone from 2007?
I understand that Apple can't test for every possible variable of use all over the world, but they don't even seem to acknowledge that they have a problem with the IP4 that will not be resolved by replacing it with a new unit. They want me to believe it's a fluke, or it's just me...but I've been combing these threads and see a lot of people reporting the same issues I am--battery drain and wildly fluctuating signal strength issues, wi-fi problems, and dropped calls. Can't someone get on this? Because otherwise Apple is going to have to admit that their IP4 is not a good solution for people who live in areas of less than perfect signal strength or use wifi or whatever demonic combo I have in my home/work setting.
Or people will have to do what I have done--if you who want the cool IP4 non-phone features, you will have to dumb down your IP4 in order to have it be even moderately useful as *a phone.* For $599 I expected better.
My (temporary) workaround?
To spare the battery:
*Turn off wi-fi (which *****, because now I have to burn minutes when I'm at work using the email, downloads, safari, etc--and it's E network, so it's SLLOOOOOOOW)
*turn off push and fetch, have mail get new messages manually
*turn off data roaming
To keep the signal somewhat stable (making it easier to complete calls and spare battery)
*Turn off 3G (this leaves me on E network--fabulous, I had that with my 3 year old iPhone)
*grip IP4 between two fingers placed at the top of the phone, away from death zone. Tough for us lefty phone users.
*pray the free bumper will a) come soon and b) help. I'm not optimistic.
To keep proximity sensor from going nuts and dropping calls, muting, turning on speaker etc:
*use headset or bluetooth (unless you are also having one of the known bluetooth issues!)
*keep phone pressed to one ear and don't move it a millimeter. Don't shift sides, don't hold phone with your shoulder, just keep it to one ear and talk fast).
I'm about out of patience. I understand that lots of folks have and love their IP4s. I'd love to be one of those people. I'm open to suggestions and have spent many hours on phone with tech support, restoring my phone, reloading data and apps--there has to be a better way.
Sorry for the thread-jacking, but someone from Apple has got to be following these threads--help us!
null

Tecra 9000: SD card reader will not work with XP

I have made some progress with this subject, it seems that Cardbus devices cannot share IRQs, although the main issue is that the memory address FFDFB200-FFDFB3FF is shared by both the SD card controller and the SD Card Memory Device. Unless a way to modify the registry can be found to resolve this memory conflict, the simple answer is that the SD card reader won't work under XP.
I think this would take some major surgery of the registry or re-writing of the drivers to move the memory address used by the SD card device, I am still working on this for now.
Can someone from Toshiba Support or Toshiba Marketing please explain to me why my Tecra T9100 has a sticker with "Designed for Windows XP and Windows 2000" on it, when Toshiba don't fully support XP on the 9000 series?
David
[Edited by: admin]

Hi David
Unfortunately, I dont think that you will find here someone from Toshiba marketing or other departments. This is ONLY a user to user forum.
What you say is simply NOT true.
The Tecra 9000 was delivered with 3 different OS.
It was delivered with Windows XP Pro, W2k and Win98. You can order all this Toshiba images from the Toshiba service partner. Therefore Tecra 9000 does support Windows XP!
Tecra 9100 was delivered with Windows XP and Windows 2000 and supports also Windows XP!
Of course there are different models with different hardware configuration but all supports WinXP.
I dont know why you get this error message or why you cannot use the SD card but I assume you dont use the Toshiba image. Therefore you have installed your OS not correctly. Because youre a newbie you dont know that the whole Toshiba driver installation must be done in the right order and all the Microsoft QFEs must be also installed.
As you see you have to pay attention to many important things if you want to install the OS manually.
Have a nice day

"Random" play doesn't work,stops after each song; multiple plays of same

One of the more annoying things happening: random doesn't work.
I've gone through the Zen Media Explorer, reformated the Zen player, so there were no songs on it.
Went and built a list of 37 songs and uploaded via Zen Media Player to the Zen player.
Went to "Music" and selected "All Tracks"
Set my "System" "Audio Settings" for "random" play.
I had to pick the first song to start it off.
It played the first 5 or so songs correctly.
Then it stopped.
I used the bottom arrow key to "play" the next song. Then it stopped AGAIN.
Now I'm manually making each song play! This goes on for 4-5 songs, then it starts playing automatically - but repeating the songs it has already played. It does not go near the other 28 or so songs that I have not heard yet!
I go back to "Music" and re-set to "All Tracks"
I go back to "System" "Audio Settings" and re-set to play "random"
And it does this annoying routine all over again.
Went back to "System" "Audio Settings" and picked "normal" this time. So of course, its playing all the same songs I've heard over again.
I have to manually cruise the "All Tracks" to pick what I want to hear.
Can anyone help me with this? I can't stand it anymore.

If you installed any software to work with the mouse, remove it according to the developer's instructions, then restart the computer and test. Back up all data before making any changes.

Ipod not recognized and Restore doesn't work

i have an ipod classic 160 GB, with disk mode enabled. When i connect it to the mac mini, it calls up iTunes. but then the message comes up that ipod can't be recognized. So i have restored it (using the latest updates, by connecting to the net) and then synced. During ejecting the ipod too, the proper procedure has been followed. However, at the end of all of it (i have 10000+ items in iTunes and it takes a LOOONG time to sync), when i try to use the disconnected ipod, it shows 'No Music', 'No Playlists', no this, no that...
I have also gone thru some other posts in this forum which suggested methods (such as getting ipod into disk mode and then connecting, trashing ipod software updates and reinstalling), to try to rectify the problem but there has been no difference And BTW, now i check, ipod shows 92 GB free (of the 160 GB). so what been copied, and where is it? or is the flash drive corrupted?
Pls HELP, as I need the ipod and my music
BTW, I think that this problem has become more pronounced since I installed the latest iTunes update (7.6.1)

Try this...
*Checking hard-drive for errors*
Hold Menu+Select on the iPod for about 6 seconds until it resets, then hold Menu+Play as soon as the Apple logo appears, again for about 6 seconds to put the machine in disk mode. Connect to your computer, closing iTunes if it opens. Run *Disk Utility / Repair Disk* for the iPod. This should find and correct any errors in the logical & physical structures of your iPod's hard drive. Once these have been fixed you can reset the iPod (hold Menu+Select ) and should stand a better chance of a successful restore.
Once you've restored your iPod don't rush to dump all the data back exactly as it was before. Complex smart playlists can sometimes trigger constant reboots or dumping of the iPod's library. In addition, larger transfers can fail leaving data in an inconsistent state. Try this technique for populating the iPod in stages.
*Break up large transfers*
In iTunes select the menu item *File... New Smart Playlist*. Change the first drop-down box to Playlist, the next to is and the next to Music. Tick against *Limit to*, type in say 10, then change the drop-down to GB, and set the last drop-down to artist. When you click OK you can enter a name for the playlist, e.g. Transfer. Now sync this playlist to your iPod rather than your entire library. When the sync is complete modify the rule ( *File... Edit playlist* ) to increase the size by your chosen amount, then sync and repeat. You can experiment with different size increments, if it doesn't work just choose something a bit smaller until it works each time. Before long you should have all your music on your iPod. Once that's done you can move on to other media such as podcasts, videos, photos etc.
tt2

ITunes (as well as Quick Time) doesn't work

Just bought an iPod (Classic Video 160GB) and tried to install iTunes 7.5 (incl. QuickTime 7.3).
Installation goes perfectly well. However, when I try to start the programs, the problems begin.
QuickTime gives me a 'Buffer Overrun' when I try to start the program.
+Buffer overrun detected!+
+Program: C:\Program Files\QuickTime\QuickTimePlayer.exe+
+A buffer overrun has been detected which has corrupted the program's internal state. The program cannot safely continue execution and must now be terminated.+
I tried to uninstall Quicktime but this doesn't work as the (un)installation program does a rollback at the end of the uninstallation not completing the uninstallation (even reversing it if I'm not mistaking). Have tried uninstalling it with Zsoft Uninstaller and Revo Uninstaller without success.
iTunes on the other hand gives an error as well. It's one of those errors in which Windows asks you if you want to send a report. If I do, the 'Microsoft Solution Website' tells me that I haven't got the latest version of iTunes, not true offcourse.
http://wer.microsoft.com/Responses/Response.aspx/7277/en/5.1.2600.2.00010300.2.0 ?SGD=14182881-006f-4a45-b4fa-e8decdf82d56
What I already tried:
-Uninstalling and reinstalling iTunes
-Deleting all temp-files through disk cleanup as well as manually
-I have Windows XP, _fully updated_
-Running multiple anti-virus and anti-spyware programs
-Ridding my C:\Windows\system32\ directory of any Quicktime files other than QuickTime.qts and QuickTimeVR.qtx (as suggested in the QuickTime-forum)
-Installing an older version of QuickTime (obviously didn't work because a newer version is already installed.
-Cleaning my Registry with Abexo Free Registry Cleaner
For your information, have never used or tried to install iTunes on my laptop before. I have had QuickTime on my laptop in the past but installed the Quick Time Alternative instead (which I uninstalled yesterday, hoping that would solve the problem).
As I have tried to find a solution to my problems all day now and am not able to find any answers, I hope someone here will point me in the right direction..!! Thank you very much in advance!

OK you need to uninstall AVI and Ace Mega codec pack and you have already uninstalled Quicktime alternative.
Once you ahve uninstalled the codec packs
Download the stand alone Quicktime:
http://www.apple.com/quicktime/download/win.html
Now Remove Quicktime using the method here (just Quicktime):
http://docs.info.apple.com/article.html?artnum=93698
Or for Vista
http://docs.info.apple.com/article.html?artnum=305409
When you come to your C:\Windows\system32\ folder you can delete any file or folder with Quicktime in the name.
Restart you computer
Install the stand alone Quicktime and check if it starts.
If it does you are in a position to find out if iTunes is OK.

Mplyer sound doesn't work, instead amarok's sond work !!!

hi everyone, the problem is that mplayer's sound doesn't work.
the sound with Amarok and Firefox(e.g youtube) works, but with mpalyer no !!!
i've posted some commands:
thanks
/etc/mplayer/
codecs.conf example.conf input.conf
/etc/mplayer/example.conf
# MPlayer configuration file
# Configuration files are read system-wide from /usr/local/etc/mplayer.conf
# and per-user from ~/.mplayer/config, where per-user settings override
# system-wide settings, all of which are overrriden by the command line.
# The configuration file settings are the same as the command line
# options without the preceding '-'.
# See the CONFIGURATION FILES section in the man page
# for a detailed description of the syntax.
# Profiles should be placed at the bottom of the configuration file to ensure
# that settings wanted as defaults are not restricted to specific profiles.
# video settings #
# Specify default video driver (see -vo help for a list).
#vo=xv
# Use SDL video with the aalib subdriver by default.
#vo = sdl:aalib
# FBdev driver:
# mode to use (read from fb.modes)
#fbmode = 640x480-120
# location of the fb.modes file
#fbmodeconfig = /etc/fb.modes
# Specify your monitor timings for the vesa and fbdev video output drivers.
# See /etc/X11/XF86Config for timings. Be careful; if you specify settings
# that exceed the capabilities of your monitor, you may damage it.
# horizontal frequency range (k stands for 1000)
#monitor-hfreq = 31.5k-50k,70k
# vertical frequency range
#monitor-vfreq = 50-90
# dotclock (or pixelclock) range (m stands for 1000000)
#monitor-dotclock = 30M-300M
# Start in fullscreen mode by default.
#fs=yes
# Change to a different videomode when going fullscreen.
#vm=yes
# Override the autodetected color depth, may need 'vm=yes' as well.
#bpp=0
# Enable software scaling (powerful CPU needed) for video output
# drivers that do not support hardware scaling.
#zoom=yes
# standard monitor size, with square pixels
#monitoraspect=4:3
# Use this for a widescreen monitor, non-square pixels.
#monitoraspect=16:9
# Keep the player window on top of all other windows.
#ontop=yes
# audio settings #
# Specify default audio driver (see -ao help for a list).
#ao=oss
# Use SDL audio driver with the esd subdriver by default.
#ao = sdl:esd
# Specify the mixer device.
#mixer = /dev/mixer
# Resample the sound to 44100Hz with the lavcresample audio filter.
#af=lavcresample=44100
# Output audio to S/PDIF
#ao=alsa:device=spdif
#ac=hwac3,hwdts,hwmpa,
# other settings #
# Pretend to be Window Media Player.
# Fixes playback when playlist and media file use the same URL.
#user-agent=NSPlayer/4.1.0.3856
# Pretend to be Quicktime
# Fixes playback for apple.com/trailers redirects
#user-agent="QuickTime"
# Pretend to be Realplayer SP
# Fixes playback for some video streaming sites
#user-agent=RMA/1.0
# Pretend to have lots of bandwidth
# Speeds up realmedia rtsp:// streams
#bandwidth=2000000
# Pretend to be Winamp
# Fixes playback of some NSV streams
#user-agent="Winamp NSV Player/5.12 (ultravox/2.0)"
# Drop frames to preserve audio/video sync.
#framedrop = yes
# Specify your preferred skin here (skins are searched for in
# /usr/local/share/mplayer/skins/<name> and ~/.mplayer/skins/<name>).
#skin = Abyss
# Resample the font alphamap.
# 0 plain white fonts
# 0.75 very narrow black outline (default)
# 1 narrow black outline
# 10 bold black outline
#ffactor = 0.75
# cache settings
# Use 8MB input cache by default.
#cache = 8192
# Prefill 20% of the cache before starting playback.
#cache-min = 20.0
# Prefill 50% of the cache before restarting playback after the cache emptied.
#cache-seek-min = 50
# DVD: Display English subtitles if available.
#slang = en
# DVD: Play English audio tracks if available.
#alang = en
# Profiles #
# The options declared as part of profiles override global default settings,
# but only take effect when the profile is active.
[protocol.dvdnav]
#vc=ffmpeg12,
#mouse-movements=yes
#nocache=yes
#[vo.vdpau]
#vc=ffmpeg12vdpau,ffwmv3vdpau,ffvc1vdpau,ffh264vdpau,ffodivxvdpau,
# Most video filters do not work with vdpau.
#vf-clr=yes
# OSD progress bar vertical alignment
#progbar-align=50
# You can also include other configuration files.
#include = /path/to/the/file/you/want/to/include
~/.mplayer/config
# Write your default config options here!
# [default] viene applicata a ogni file
[default]
# usa il server grafico X come video output
vo=xv
# usa alsa per l'audio output
ao=alsa
# ao=oss # Use OSS4
# decodifica multithreaded H264/MPEG-1/2 (valido: 1-8)
lavdopts=threads=2
# impostare il canale audio preferito (in questo esempio il numero sei)
channels = 6
# scala i sottotitoli al 3% della dimensione dello schermo
subfont-text-scale = 3
# non usa fontconfig
nofontconfig = 1
# aggiunge bordi neri ai filmati che non hanno lo stesso aspetto di forma dello schermo
# per wide screen monitors
vf-add=expand=::::1:16/9:16
# per non wide screen traditional monitors
#vf-add=expand=::::1:4/3:16
#profilo di up-mixing da due canali audio a sei canali
# use -profile 2chto6ch to activate
[2chto6ch]
af-add=pan=6:1:0:.4:0:.6:2:0:1:0:.4:.6:2
#profilo di down-mixing da sei canali audio a due canali
# use -profile 6chto2ch to activate
[6chto2ch]
af-add=pan=2:0.7:0:0:0.7:0.5:0:0:0.5:0.6:0.6:0:0
# Disabilita screensaver
heartbeat-cmd="xscreensaver-command -deactivate &" # stop xscreensaver
stop-xscreensaver="yes" # stop gnome-screensaver
ls /etc/modprobe.d/
alsa-base.conf snd-hda-intel.conf
etc/modprobe.d/alsa-base.conf
options snd slots=snd_mia,snd_hda_intel
options snd_mia index=1
options snd_hda_intel index=0
/etc/modprobe.d/snd-hda-intel.conf
options snd-hda-intel model=auto
cat /proc/asound/modules
0 snd_hda_intel
lsmod |grep snd
snd_hda_codec_hdmi 30162 1
snd_hda_codec_conexant 36759 1
snd_hda_intel 37000 2
snd_hda_codec 150305 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 6340 1 snd_hda_codec
snd_pcm 77645 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel
snd_page_alloc 7210 2 snd_pcm,snd_hda_intel
snd_timer 18726 1 snd_pcm
snd 59109 11 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_hda_codec,snd_hda_intel
soundcore 5450 1 snd

Neburski wrote:
ryanjacobs wrote:So, apparently, your system cannot find the ALSA output driver. I suggest that you use a different driver than ALSA.
OP should first go through the wiki page of ALSA to ensure that his ALSA setup is working correctly. There aren't many sound setups that do not work under ALSA. If OP is relying on another sound setup then he should follow the appropriate wiki and tell us so.
@otto88: It would also help if you would try to explain what your intentions were. I'm assuming you merely want to have sound working and not configure some fancy setup. In that case you should just stick to a basic setup and follow the wiki step by step (don't skip any line and if you don't understand something, you figure that out or you ask people, don't just ignore it).
For instance I don't even have those /etc/modprobe.d/alsa-base.conf and /etc/modprobe.d/snd-hda-intel.conf even though I have 2 sound devices, while you seem to only have 1 sound device
otto88 wrote:cat /proc/asound/modules
0 snd_hda_intel
So your /etc/modprobe.d/alsa-base.conf in that case is totally unnecessary, let alone that you don't even have the snd_mia module loaded so why do you even configure alsa to load it at index 1. You aren't supposed to simply copy and paste the configurations from the wiki. Those configurations are merely there to give you an idea on how to make your own configuration.
When you have ensured that your sound is been set up correctly then you can start with the most basic mplayer configuration. You keep the /etc/mplayer/example.cong configuration file totally commented out (like you have atm) and your ~/.mplayer/config should only contain
ao=alsa
ok i just followed the wiki and your advices and doesn't work, yet
mplayer -ao alsa /dati/Musica/StudyDue.mp3
MPlayer SVN-r36498-snapshot-4.8.2 (C) 2000-2013 MPlayer Team
206 audio & 433 video codecs
mplayer: could not connect to socket
mplayer: No such file or directory
Failed to open LIRC support. You will not be able to use your remote control.
Playing /dati/Musica/StudyDue.mp3.
libavformat version 55.19.104 (internal)
Audio only file format detected.
Load subtitles in /dati/Musica/
==========================================================================
Opening audio decoder: [mpg123] MPEG 1.0/2.0/2.5 layers I, II, III
AUDIO: 22050 Hz, 2 ch, s16le, 32.0 kbit/4.54% (ratio: 4000->88200)
Selected audio codec: [mpg123] afm: mpg123 (MPEG 1.0/2.0/2.5 layers I, II, III)
==========================================================================
[AO_ALSA] Playback open error: No such file or directory
Failed to initialize audio driver 'alsa'
Could not open/initialize audio device -> no sound.
Audio: no sound
Video: no video
Exiting... (End of file)

Flash doesn't work?

It seems flash player doesn't work in the browser.. I guess it works some of the time as I was able to load and run a tiny .swf demo/game.
But when I go to YouTube for example it doesn't load the video in the web page. (As an example; I know stand-alone Youtube clients are available)
Phone is an E51 by the way.

This is because the E51 only has flashlite 2.0 and the youtube site (and many others) needs flashlite 3.0 to work.
The only way to get flashlite 3.0 on your phone is if nokia adds support for it in a future firmware update. When and if this will happen is anybodys guess. So far the only phone to see this feature in an update is the N95 8GB.

Flush Event Queue doesn't work with "Key up"

Hi,
probably just a simple thing I am missing here. See the attached VI (including SubVI). In case 1 I fetch the Key Up event for ENTER and issue a Value Change on the Stop Button. This results in a check for the string length and in case it is too short brings up a dialog telling you the ID string is too short and brings you back to the ID entry. Unfortunately - when confirming the dialog with ENTER instead of using the mouse on the button theKey Up event fired again and therefore fetched by the Event Structure.
So I thought I just flush all events in the queue. To be sure, I put a time value on the flush function which proceeds AFTER the dialog is completed, so the ENTER Key Up should be deleted as well. Bummer is - it doesn't work. Anyone know why?
I tried as well with the dynamic event, which I unregistered right after the Stop Event is issued in the Key Up case. I then "re"register for the Key Up event at the same time/position as the flush event queue function is positioned now in the VI below. Still no joy.
What is my mistake? Thanks a lot.
Solved!
Go to Solution.
Attachments:
Manual_ID_Entry.llb ‏47 KB

comrade wrote:
I don't understand 2 things:
a) Why is the Key up event even fired? It doesn't come from the VI where the event structure resides and to which "Instance" the event is bound (VI->Key up), but from the dialog box (which is a different VI). Unless a calling VI inherits all events from its SubVIs or something like that.
b) Why isn't the event fired by the button in the dialog box discarded as the flush event queue function is supposed to perform?
Because you are slow. Not you personally. But compared to the computer, you just don't stand a chance. So you hit the Enter button on the dialog. That dialog's OK button activates on the key down. So the dialog is long gone by the time you manage to get your finger off of the Enter key. In fact, you loop should be back around to be waiting for an event first. So it is waiting for an event when you finally get your finger off of the button. Hey, we have a Key Up event!
Your current checking for the validity of the id is just flat out annoying. Use the Key Down? event to check for a valid character being entered. Notice the '?' in my choice of event there? That means it is a filter event. This means you can throw away (discard) the character being pressed before the control even sees it. You could also discard if there are already enough characters (Greater Or Equal, not Equal).
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Preview function doesn't work in Cap2

I just installed Captivate2. In the project I'm working on,
the Preview function doesn't work. Or rather, it works
sporadically... sometimes it does, and --- much more often -- it
does not. What happens instead is, the "generating slides" message
appears, and the progress-bar begins, but then suddenly the
message/progress window disappears, WITHOUT generating the swf file
and without doing any kind of preview. It happens on all the
various options of the Preview function.
It does work about one time in every ten attempts.
This surely isn't acceptable... Anyone else encountering
this???

Hi UncleErnie
By chance have you fiddled with the slide properties of any
of the slides? One of the new options available in version 2 is to
apply navigation options that cause slides to behave certain ways.
So it stands to reason that if a slide was configured to jump to
the end of the movie and the end of the movie option was to close
the movie... Well, hopefully you see what I mean.
Another question I would have is where are you editing your
project? Are you possibly saving it to the company LAN and editing
it using Captivate to make edits while in that location? If so,
this is normally bad practice. Try moving the project locally and
see if the issue resolves.
Cheers... Rick

"Calculate Average" option for the Activity Usage Profile doesn't work

I have the same problem as poster 793128 in a comment for a different thread: the "calculate average" profile option doesn't work for units (it works for cost though). I've used this option a lot on previous versions of Primavera but for some reason is not working on our new P6 release 7 (stand alone). As 793128’s post says: nothing happens, nothing changes, the profile keep showing totals, doesn't matter if the "base hours on time period" box is selected or if the divider is input by the user.
The same option (calculate average / divide by) on the resource usage spreadsheet and on the tabular reports do work as expected so doesn't seem to be that I checked the wrong box for some user or administrator preference set up.
Thank you for any help or clue. I posted this as a different thread because my original post was in a resource profile thread for a different issue that was already answered.

*793365,*
After reading your post I tested an older layout of mine that uses a similar setup and it still operates fine. On the "Resource Usage Profile Options" box under the "Graph" tab, I have "Calculate Average" checked and "24" entered in the "Divide interval totals by:" box.
This allows my resource profile to display manhours per day for me.
Some of my background info:
I run in a multi-users platform and not in a stand alone setup.
We have different resources loaded into the schedule with multiple calendars.
I have several "Resource Filter/Group Names" setup for each separate resource on the "Data" tab too.
Hope this helps,

Tecra T9100, XP, Stand By doesn't work

Similar Messages

Maybe you are looking for