Tell iPhone to NOT sleep when connected to dock?
I can't seem to find any setting where I can accomplish this. Am I missing something?
Even i noticed this problem recently when the sync and backup started to took ages to complete. I kept my phone on the dock for syncing and it was on all through the night. Looks like my iphone has lost its sleep..:)
Similar Messages
-
IPhone 4 not recognized when connected to new USB 2.0 card
I have an iphone 4 OS4.1 on a no-name Windows XP Pro (service pack 3) PC with an AMD processor and lots of RAM.
I had the phone working and syncing beautifully with the onboard USB 1.1 but it was slow. So I bought a new PCI USB 2.0 card and installed it. Card is installed and there are no problems according to the status in System Devices.
But the computer does not recognize the iphone when plugged into one of those ports. If I plug it into one of the USB 1.1 ports that are still in the machine, it syncs and works fine. If I plug it into one of the new USB 2.0 ports, the PC shows the window at bottom right saying the device is not recognized. Tried the wizard but it's useless.
THOUGHTS?????Nevermind!!!
It turned out to be a faulty cable! I tried it with a different sync cable and it works fine!
So disregard the question above. -
My iphone will not sync when connected to itunes
I just purchased an iphone5. I have an ipad and have connected that to itunes, but when i connect my phone itunes doesn't recognize it and it doesnt sync?
Any suggestions.appledumplingwithcaramelsauce_2 wrote:
Nothing happens did you not read my question properly
Then why did you mark the response as correct/solved?
You could help out here. Something must happen. Some series of events takes place even of the devices don't sync. That's what AmishCake is asking. -
Emails will not send when connected to wifi
Emails on my iPad and iPhone will not send when connected to wifi, any help would be appreciated
iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
Cheers, Tom -
My iphone won't synch when connected
My iPhone will not synch when connected to my iMac. It just started happening. It an iPhone 5, all apps and software are up to date.
Thanks
jimI a;ready take off the acces of the computer and reput it
-
My iphone 4 is not being detected by any of my computers and not charging when connected to any computer. It will, however, charge to the car or wall. The only change that I can think of is that I downloaded a podcast from itunes directly from my phone. I've since deleted this podcast with no luck. I've restarted both the phone and the computer, still no luck. One computer is running Vista and the other Windows 7, both have the latest Itunes Update. Anyone have a fix for this?
You clearly did not notice that you have joined a USER TO USER COMMUNITY FORUM
This is NOT Apple ,Apple do not read nor do they therefore respond
So if you would like to wind your neck in ........................
try a reset of iPhone and then a restore,best, as new and if it then functions correctly try restoring with your backup -
My iPhone 5 got problem when connect with lighting cable, this will keep pop up message "this accessory may not be supported", I can't charge or sync at all. I tried plug and unplug many time, still can't detect/charge my iPhone5, but sometime will 'lucky' that can connect to my iTunes and charge battery…
This message will auto pop up also when I don't have plug anything in my iPhone 5, It is very annoying…
The lighting cable is original and now i'm using OS 7.0.4 / iTunes is 11.1.3
What I can do to fix this problem? Thank you.I would try using another cable you can likely borrow one to test from somebody
if it's the same then likely the connector in your iphone have been damaged -
pioneer 8400 DVD receiver player, as iPhone ios6 update now when connecting the new iPhone with ios6 to my car DVD 8400 unit, when playing music such as on my phone or Pandora the track button does not function or work at all not even if i press skip track forward or back on the unit it doesn't function everything works except that. on listening to radio or anything else related not pairing thru Bluetooth unit works fine, seems there to be Bluetooth update that is not making iPhone and unit not compatible at all. does pioneer need fix this problem with update firmware or thru apple need help. my iPhone was working fine before with previous ios 5 before.
Dear Valued Pioneer Customer:
We would like to inform you of the availability of an optional Bluetooth® firmware update (HW05-SW01.27.20) that enables Bluetooth AVRCP control and metadata display from a compatible Pioneer CD or DVD Receiver when used with an iPhone® 5 or iOS 6 device. If you do not own an iPhone 5 or iOS 6 device, there is no need to install this update.
This firmware update may be used only with the following 2012 Pioneer products:
CD Receivers
DVD Receivers
DEH-P8400BH
DEH-P9400BH
DEH-80PRS
AVH-P2400BT
AVH-P3400BH
AVH-P4400BH
AVH-P8400BH
In order to perform this update, the following items are needed:
A Pioneer CD or DVD Receiver above with built-in Bluetooth
Laptop with built-in Bluetooth running Windows® 7
Bluetooth firmware update (HW05-SW01.27.20)
How to Obtain the Free Firmware Update
1. Download the INSTRUCTIONS for the optional Bluetooth firmware update (HW05_SW01.27.20).
2. Download the UPDATE FILE to a computer and transfer the file to a compatible 2012 Pioneer CD or DVD Receiver via a Bluetooth-enabled Windows 7 laptop.
You can also arrange for Pioneer to update your 2012 Pioneer CD or DVD Receiver by calling Pioneer Customer Service toll free at 800-421-1404 during regular business hours (M-F 10AM-7:30PM Eastern Time, except on holidays). If this firmware update is performed by Pioneer, there is a charge of $60.00 (this charge includes return shipping of the updated unit within the U.S.). Charges for removal/reinstallation of the unit and shipment to Pioneer are the customer’s responsibility.
How to Determine if the Firware Update has Already been Installed
CD Receivers:
• With the unit turned off (press and hold the source button until the CD Receiver turns off), press and hold the center of the volume knob to bring up the Settings menu → rotate the volume knob until "BT Version Info" is displayed and then press the center of the volume knob → The firmware version should show HW05-SW01.27.20.
DVD Receivers:
• With the unit turned off (press the home button and select ‘OFF’ from the source icons), press the home button → Press the “System” icon at the bottom of the screen → Select the “Bluetooth Version Info” option → The firmware version should show HW05-SW01.27.20.
If the Bluetooth firmware version shows HW05-SW01.27.20, no further action is necessary.
Questions
If you have any questions, please contact the Pioneer Customer Service Center toll free at 1-800-421-1404, Monday through Friday, 10:00 a.m. to 7:30 p.m. (Eastern Time), except on holidays.
Sincerely,
Pioneer Electronics (USA) Inc. -
Itunes 10.4 not launching when connecting iphone
Snow Leopard 10.6.8. Just updated iTunes to 10.4. iTunes will not launch when connecting the iPhone to my MacBook Pro. Once connected, manually opening iTunes will allow the sync to happen, but only then. iTunes helper app is there in Login items.
Minor inconvenience, but could be a problem if I miss too many syncs due to this.
Any thoughts?I had the exact same problem upgrading iTunes to 10.4 on Snow Leopard. It looks like there's a problem with iTunesHelper under Login Items. I found the solution here: https://discussions.apple.com/message/15666966 Simply follow the instructions to re-add iTunesHelper to Login Items, restart, and you should be good to go!
-
My iPhone 5 is freezing when connected to the charger. This is not happinning if it is connected to the computer USB. How to solve this problem?
Possibly faulty charger. The supplied Apple Charger is covered by the iPhone Warranty. Make Genius reservation or set up service and take or send iPhone and Charger to Apple for resolution.
-
why does my iphone say device not supported when connecting to my mac pro, even though it has already succesfuly paired? I also use a wirless bluetooth keyboard and mouse on the computer successfully.
Also when I turn Bluetooth on on the phone the devices cog never stops turning (forever serching for a device)iTunes automatically syncs voice memos to your iTunes library when you connect iPhone to your computer.
It couldn't be much easier than that as you don't actually have to do anything more than normal.
This lets you listen to voice memos on your computer and provides a backup if you delete them from iPhone.
Voice memos are synced to the Voice Memos playlist. iTunes creates the playlist if it doesn’t exist. When you sync voice memos to iTunes, they remain in the Voice Memos application until you delete them. If you delete a voice memo on iPhone, it isn’t deleted from the Voice Memos playlist in iTunes. However, if you delete a voice memo from iTunes, it is deleted from iPhone the next time you sync with iTunes.
USB syncing is far faster than Bluetooth. -
X120e does not sleep when lid closed
I found another similar post, however it was resolved by the individual reinstalling the operating system.
My issue is more complicated. I have made sure everything is up to date, all the settings that tell the system to sleep when the lid is closed are turned on. I have even turned those settings off off, just so I could turn them back on to make sure there wasn't something quirky about it.
I have tried restoring the system to factory settings using the recovery partition, as well as discs burned from the program that came with the computer. I have tried clean install from Windows 7, 8, and 8.1 discs.
The unit still does not sleep. I don't ever remembering it being able to. I once closed the display thinking it would sleep (power was plugged in). Woke up the next day, went to work for 8 hours, came back and felt that the system was really hot. Opened the lid and the screen was exactly as I had left it the day before.
When I first got the system in 2012, the screen did not work, so I actually had to send it to Atlanta, GA for repairs. It came back quickly, and it still did not work, so I actually sent it back to Atlanta, GA's repair center a second time in the same week. It came back working and I left it alone. I never tested the sleep/wake because I always just turned the system off when I was done with it, but now I am back in school and this little computer comes in handy, but I don't want to turn off the system manually going from class to class when I need to pack it away in my bag.
Could there be a hardware issue? Something inside not connected? This laptop works perfectly EXCEPT for the fact that it will not sleep when the lid is closed. It is out of warranty but had I known this was an issue while it was still under warranty, I would have inquired. This unit is in pretty fantastic shape, looks brand new too. No damage, never been dropped, and only ever handled by me (never loaned out).
How can I fix this?Thanks for the reply, gat0gelat0.
Yes, those settings were the first things I checked. I also tried changing it to "Do nothing", then changing back to the sleeping option. It still does nothing when I close the lid.
I would like the functionality of it going to sleep when I close the lid for the convenience, like when class ends, I have to rush to my next class, I just want to close the lid, put it in my bag and run to the next class. Keyboard shortcuts like Fn-F4 work, but this laptop should have the functionality I am describing, and I want to figure out why it isn't working and how to fix it.
I suspect there is an issue with whatever is used hardware wise to sleep the machine. Either it's not being triggered, or it's not there, or it's broken. I've tried running a magnet around the bezel of the LCD screen as well as around the palm rest bezel and there is no activity as I've read that many laptops trigger sleep by interaction by a magnet. Still nothing. -
HT201415 My iPhone is not having wifi connection anywhere
My iPhone is not having wifi connection anywhere
Hi PamelaVR,
Thanks for visiting Apple Support Communities.
I recommend starting with these troubleshooting steps if your iPhone battery is not behaving as you'd expect:
Battery does not charge
Verify that the outlet being used is working.
Try another USB power adapter if available.
If no other USB power adapter is available, try connecting to a high-power USB 2.0 port (not a keyboard). The computer must be turned on and not in sleep or standby mode.
Try another USB cable if available.
iPhone or iPod touch displays the low-battery image and is unresponsive
If you see the image below, charge the iPhone or iPod touch with USB power adapter for at least 15 minutes.
You should see this image when iPhone or iPod touch begins to charge:
If the screen still displays the low-battery icon, try turning the iPhone or iPod touch off and then on again.
If the issue persists, follow these troubleshooting steps.
From:
iPhone and iPod touch: Charging the battery
http://support.apple.com/kb/HT1476
Regards,
Jeremy -
my iphone wont turn on when connected to a laptop or pc,but when its connected to my charging stereo,its shows i need to conect to itunes but then after 10-15 min. it turns off.
Hi Monzairita,
Thanks for visiting Apple Support Communities.
If your iPhone only powers on when connected to a dock, and shows the "connect to iTunes" screen, start with these troubleshooting steps:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Best Regards,
Jeremy -
Macbook Pro 13" will not sleep when I shut the lid
Hello Community,
This is my first time using the forum. I have a macbook pro 13" 2009 model. Recently I had my MBP connected to an external monitor. I shut the lid while it was connected to the monitor and forgot to turn off my bluetooth mouse. Later that night the mouse was bumped, waking my macbook and setting it to clamshell mode. I put it to sleep again, opened the lid and woke it, but the LCD on the laptop did not turn on. I reset the PRAM and the NVRAM with no luck. I disconnected the monitor, rested the P/NVRAM and it would boot with the laptop screen and once everything was loaded my screen went black and then went to sleep on its own. I tried powering on and off using the P/NVRAM key commands...and nothing. So I opened the bottom case and physically disconnect the battery, reconnected the battery, put the bottom plate back on and powered it up. The screen began working again, now I have a new problem, the MBP WILL NOT sleep when I shut the lid anymore. I even reinstalled the OS and still no luck? If anyone has anything helpful that I could try to get this feature working again it would be much appreciated. If there is some terminal command I could try or some other troubleshooting method. I even put a magnet by the right side of the keyboard to try to trigger the sleep switch.
Any advice would be appreciated.I resolved my issue in a very unlikely way. In my earlier post I mentioned that I wiped my hard drive and was starting from scratch. Well I reinstalled windows 7 through bootcamp and it fixed my sleep issue. That's right folks...Windows fixed my mac. I think that it was an EFI issue. I think this because windows 7 uses EFI and during installation it must have reset the sleep values to normal. I feel when you reinstall Mac OSX the EFI partition on the drive should get wiped and reinstalled as well. I also feel that apple should have an option within System Prefs for the user to select what the way is that the computer responds when the lid is shut instead of the ritual of trickery and problems that the clamshell mode can cause.
Hope this helps someone.
Maybe you are looking for
-
Multiple iPhoto libraries to manage photostreams in different ways
My wife and I both have iPhone's. I have a 5s and she a 5. We share an iCloud account so that all photos she takes and ones I take go into one photostream and then automatically get loaded on my iMac hard drive. This way we are sure to not lose any p
-
Is there a way to import my google calendar into ical? I have my google email account set up using the mac mail client and it works great, but I need my calendar too. Is this possible?
-
Photoshop CS4 will not launch on iMac 10.7.5
PLease help! I tried everything with the Genius Bar at the Apple store and we can't figure it out.
-
Planned Delivery Time from Material Master instead of PIRs
Hi SAP Gurus, Do you know if there is a way to have MRP look at the Planned Delivery Time from the Material Master (MRP 2 tab) instead of the PIR? We would like to create global PIRs with a PDT of 1 and have the Material Master PDT set to a different
-
I want to talk via phone to a real live person to give new credit card info
I need to talk to a person. I have no idea how to use this page