Telnet session terminating

Hi,
When i login to the server which is using Solaris 9 using telnet, something is breaking telnet sessions in our machines. For workaround, we changed the IP address and it got resolved for now.
I want to revert back to the original statics IP. But i am suspecting that the same issue can occur again. Why the telnet sessions are breaking? Can anybody help me out on this issue?
Thanks

Thanks for the information.
Some users are able to telnet as a application user and some random users are not able to telnet and they are facing this issue.
Their telnet sessions are terminating without showing any error. If the problem is with firewall or any network equipment then it wont work for anybody, but the issue was it is not working for only some of the random users. Is there any possibility of issue with DNS?can anybody help me out on this?

Similar Messages

Debug output in telnet session

Hi All;
Is there anybody know how to show debug output messages in telnet session?
Thanks
Alex

terminal monitor - to turn the console on in a telnet session
terminal no monitor - to turn it off
Is this what you wanted to know?

How do I establish a telnet session with unit under test?

I am going to the next step as a novice and moving from serial communications to ethernet on my unit under test. I have been all over the help and discussion forums etc and cannot find an answer. I need to open up a telnet session with my unit under test and keep it open to send commands back and forth for control of the unit. Can anyone give me a hint of how I am to establish this communication? I have the IP address and I am using port 23 but I just get the session started and then immediately closed. The sequence of events will be: start the session, the unit will reply with a username and then password, after that I need the session to remain open so I can send commands as if I am sitting at the serial port. When complete the session will then be terminated. Thanks in advance for any help.

If you want to do telnet using plain TCP, you need to do everything yourself, including the telnet options negotiation.
RFC 854 should have most of what you need (look towards the bottom).
Most likely, the server will propose a few options, which you should either accept or reject depending on your needs.
Easiest is probably to use a packet sniffer on a regular telnet session, then dissect the negotiation to see what that particular server wants.
RFC 990 has a list of telnet options, look for the section labeled "ASSIGNED TELNET OPTIONS".
It should be simple to write some code that negotiates with one particular host. It will be more difficult to write a full-blown telnet client that does general negotiations with any type of telnet server.
I have a small program that telnets to a router to do some configuration. The only thing I reply to the proposed options is:
"\FF\FD\03\FF\FE\01\r\n" (In \-codes). Translated: "Don't suppress go ahead, Do echo".
(FF=IAC "Interpret as command", FD=Do, FE=Don't, 01=echo, 03= suppress go ahead.)
LabVIEW Champion . Do more with less code and in less time .

How to recognize a telnet session (RF) from a SAPGUI?

hi guys,
i must check and block a transaction, developed for a RF terminal, if it is executed by SAPgui...
how to, in abap, recognize a telnet session (RF) from a SAPGUI ?
I have tried FM "SAPGUI_OBJECT_ID" hoping in a sy-subrc ne 0 with telnet but it's not right.
Edited by: Cacco Andrea on Apr 28, 2009 2:43 PM

i resolved like this:
    cl_gui_frontend_services=>get_computer_name(
      changing
        computer_name        = zterm
      exceptions
        cntl_error           = 1
        error_no_gui         = 2
        not_supported_by_gui = 3
        others               = 4
    if sy-subrc = 0.    "SAPGUI
else.               "telnet
    endif.

SA520 seems to terminate Telnet session

Question: We recently replaced a router with Cisco SA520. The connection is only used for a Telnet application. After replacing the router we experience the problem that the Telnet session is terminated after around one minute of inactivity in a way that it does not respond to keyboard input anymore. With out old router this happend after 30 minutes.
Everythink works fine as long as the user does actively use the system.
The SA520 is configured with a static external and internal IP address. Two ports are forwarded (515,9100) from the external side (where the Telnet server resides) to an internal printer.
Does anyone have idea what is causing this problem.
Thank you
Sascha

Your timeout is probabally set very low.
TRY THIS:
Router(config)#line vty 0 4
Router(config-line)#exec-timeout 30
If you still have a problem please let us know.
NOTE:
I did the timeout for 30 minutes because that it what your old setting was.

How can I send an F5 thru a telnet session?

I have to logon to a remote machine with a telnet session. To do this manually, I have to hit F5 to bring up the login prompt after the telnet session is established. I can establish the connection with LabVIEW, but how can I send the F5?

Telnet is essentially an ASCII-only protocol. There's no "F5" in ASCII, so you're probably supposed to send some sequence of ASCII codes to make it work.
Typically, text-based telnet programs emulate various kinds of physical terminals, such as DEC's warhorse "vt52" and "vt100" terminals, or the old ADM-3A. Those terminals sometimes had special keys that could send a sequence of commands. For example, I think the vt100 had an "F5" key that sent Escape (a byte containing decimal 27) followed by the letters "Ot". (I am looking at a UNIX box with an /etc/termcap entry for a vt100, and interpreting what it says. I'm not an expert at UNIX /etc/termcap entries, so I may be misreading it.)
Anyway, you need to find out what kind of terminal this remote machine
is expecting you to use. This will tell you what string to send for an F5 key.
I hope this helps.

Suspend reverse telnet in Terminal

Hi All,
I'm unable to suspend a reverse telnet session (e.g. from an access server to a router) with Terminal.
The character sequence is: < ctrl-shift-6> < x >
This works perfectly from the Win XP command line but not from OSX (10.5.4) Terminal. When pressing "CTRL-SHIFT-6" I hear a beep an the key combination is not accepted. Tried will all the terminal types, as ANSI rather than VT-100, with no luck?
Anybody can help?
Thanks a lot,
Davide

Post to the Unix forum under OS X Technologies where the Unix and Terminal gurus congregate.

Work process re-started , session terminated

Hi Gurus,
While i creating a purchase order (me21n) , the process runs for a while and then i am getting a SAP GUI message "Work process re - started , session terminated" and the session is closed.Can anyone give me the cause of the problem and solution for the same.
Developers Trace File Entry:
trc file: "dev_w0", trc level: 1, release: "640"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      all, M
B B Fri Aug 31 16:09:36 2007
B create_con (con_name=R/3)
B Loading DB library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' ...
B Library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' loaded
B Version of 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' is "640.00", patchlevel (0.26)
B New connection 0 created
M systemid   560 (PC with Windows NT)
M relno      6400
M patchlevel 0
M patchno    25
M intno      20020600
M make:      multithreaded, ASCII
M pid        1680
M
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 1680) [dpxxdisp.c   1160]
I MtxInit: -2 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: JAVA is not active
M DpShMCreate: sizeof(wp_adm)        7456    (828)
M DpShMCreate: sizeof(tm_adm)        2219848    (11044)
M DpShMCreate: sizeof(wp_ca_adm)        18000    (60)
M DpShMCreate: sizeof(appc_ca_adm)    6000    (60)
M DpShMCreate: sizeof(comm_adm)        192000    (384)
M DpShMCreate: sizeof(vmc_adm)        0    (320)
M DpShMCreate: sizeof(wall_adm)        (22440/34344/56/100)
M DpShMCreate: SHM_DP_ADM_KEY        (addr: 05230040, size: 2506248)
M DpShMCreate: allocated sys_adm at 05230040
M DpShMCreate: allocated wp_adm at 052317A8
M DpShMCreate: allocated tm_adm_list at 052334C8
M DpShMCreate: allocated tm_adm at 052334F0
M DpShMCreate: allocated wp_ca_adm at 05451438
M DpShMCreate: allocated appc_ca_adm at 05455A88
M DpShMCreate: allocated comm_adm_list at 054571F8
M DpShMCreate: allocated comm_adm at 05457210
M DpShMCreate: allocated vmc_adm_list at 05486010
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 05486038
M DpShMCreate: allocated wall_adm at 05486040
X EmInit: MmSetImplementation( 2 ).
X <ES> client 0 initializing ....
X Using implementation std
M <EsNT> Memory Reset enabled as NT default
X ES initialized.
M M Fri Aug 31 16:09:37 2007
M calling db_connect ...
C Thank You for using the SLOLEDB-interface
C Using dynamic link library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll'
C dbmssslib.dll patch info
C    patchlevel   0
C    patchno      26
C    patchcomment MSSQL: GetNextMsst1 error (754819)
C np:(local) connection used on IDES
C Using Provider SQLNCLI
C Provider Release:9.00.1399.06
C Using Provider SQLNCLI
C C Fri Aug 31 16:09:41 2007
C Cache sizes: header 52 bytes, 20000 names (26720000 bytes), 1000 dynamic statements (5432000 bytes), total 32152052 bytes
C Using shared procedure name cache IDES_I04I04_I04_MEM initialized by another process.
C Connected to db server : [IDES] server_used : [np:(local)], dbname: I04, dbuser: i04
C pn_id:IDES_I04I04_I04
B Connection 0 opened
B Wp Hdl ConName          ConId     ConState     TX PRM RCT MAX OPT Date     Time   DBHost         B 000 000 R/3              000000000 ACTIVE       NO YES NO 255 255 20070831 160937 IDES           C The IRow interface is supported by this OLEDB provider
M db_connect o.k.
I I Fri Aug 31 16:09:53 2007
I MtxInit: 0 0 0
M SHM_PRES_BUF            (addr: 098E0040, size: 4400128)
M SHM_ROLL_AREA        (addr: 68200040, size: 160432128)
M SHM_PAGING_AREA        (addr: 09D20040, size: 72351744)
M SHM_ROLL_ADM            (addr: 0E230040, size: 1602056)
M SHM_PAGING_ADM        (addr: 0E3C0040, size: 525344)
M ThCreateNoBuffer        allocated 320144 bytes for 1000 entries at 0E450040
M ThCreateNoBuffer        index size: 3000 elems
M ThCreateVBAdm        allocated 7424 bytes (50 server) at 0E4A0040
X EmInit: MmSetImplementation( 2 ).
X <ES> client 0 initializing ....
X Using implementation std
X ES initialized.
B db_con_shm_ini: WP_ID = 0, WP_CNT = 9
B dbtbxbuf: Buffer TABL (addr: 134C00C8, size: 30000128, end: 1515C4C8)
B dbtbxbuf: Buffer TABLP (addr: 0F3000C8, size: 10240000, end: 0FCC40C8)
B dbexpbuf: Buffer EIBUF (addr: 151600D0, size: 4194304, end: 155600D0)
B dbexpbuf: Buffer ESM   (addr: 155700D0, size: 4194304, end: 159700D0)
B dbexpbuf: Buffer CUA   (addr: 0FCE00D0, size: 3072000, end: 0FFCE0D0)
B dbexpbuf: Buffer OTR   (addr: 159800D0, size: 4194304, end: 15D800D0)
M rdisp/reinitialize_code_page -> 0
M icm/accept_remote_trace_level -> 0
C C Fri Aug 31 16:09:54 2007
C Using Provider SQLNCLI
C The IRow interface is supported by this OLEDB provider
S S Fri Aug 31 16:09:55 2007
S *** init spool environment
S initialize debug system
T Stack direction is downwards.
T debug control: prepare exclude for printer trace
T new memory block 15EFFBD0
S spool kernel/ddic check: Ok
S using table TSP02FX for frontend printing
S 1 spool work process(es) found
S frontend print via spool service enabled
S printer list size is 150
S printer type list size is 50
S queue size (profile)   = 300
S hostspool list size = 3000
S option list size is 30
S      found processing queue enabled
S found spool memory service RSPO-RCLOCKS at 1DF30098
S doing lock recovery
S setting server cache root
S found spool memory service RSPO-SERVERCACHE at 1DF302C8
S    using messages for server info
S size of spec char cache entry: 165020 bytes (timeout 100 sec)
S size of open spool request entry: 1152 bytes
S immediate print option for implicitely closed spool requests is disabled
A A -PXA--
A PXA INITIALIZATION
A PXA: Fragment Size too small: 195 MB, reducing # of fragments
A System page size: 4kb, admin_size: 11476kb.
A Attached to PXA (address 24550040, size 400000K)
A abap/pxa = shared protect gen_remote
A PXA INITIALIZATION FINISHED
A -PXA--
A A A Fri Aug 31 16:09:56 2007
A ABAP ShmAdm attached (addr=56AF9000 leng=20955136 end=57EF5000)
A >> Shm MMADM area (addr=56E610E0 leng=134752 end=56E81F40)
A >> Shm MMDAT area (addr=56E82000 leng=17248256 end=57EF5000)
A RFC Destination> destination ides_I04_00 host ides system I04 systnr 0 (ides_I04_00)
A RFC Options> H=ides,S=00
A RFC FRFC> fallback activ but this is not a central instance.
A   A RFC rfc/signon_error_log = -1
A RFC rfc/dump_connection_info = 0
A RFC rfc/dump_client_info = 0
A RFC rfc/cp_convert/ignore_error = 1
A RFC rfc/cp_convert/conversion_char = 23
A RFC rfc/wan_compress/threshold = 251
A RFC rfc/recorder_pcs not set, use defaule value: 1
A RFC rfc/delta_trc_level not set, use default value: 0
A RFC rfc/no_uuid_check not set, use default value: 0
A RFC Method> initialize RemObjDriver for ABAP Objects
A Hotpackage version: 38
M ThrCreateShObjects        allocated 9394 bytes at 0FFD0040
N SsfSapSecin: putenv(SECUDIR=C:\usr\sap\I04\DVEBMGS00\sec): ok
N N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is C:\usr\sap\I04\SYS\exe\run\sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N ===...sucessfully completed.
N =================================================
N MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
N MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
W =================================================
W === ipl_Init() called
W    ITSP Running against db release 620!
W    ITSP Disable Kernel Web GUI functionality
W === ipl_Init() returns 2, ITSPE_DISABLED: Service is disabled (sapparam)
W =================================================
B B Fri Aug 31 16:10:05 2007
B dbtran INFO (init_connection '<DEFAULT>' [MSSQL:640.00]):
B   max_blocking_factor = 50, max_in_blocking_factor      = 255,
B   min_blocking_factor =   5, min_in_blocking_factor      = 10,
B   prefer_union_all    =   1, prefer_union_for_select_all =   0,
B   prefer_fix_blocking =   0, prefer_in_itab_opt          =   0,
B   convert AVG         =   1, alias table FUPD            =   0,
B   escape_as_literal   =   0, opt GE LE to BETWEEN        =   0,
B   select *            =0x00, character encoding          =SBCS / []:X,
B   use_hints           = abap->1, dbif->0x1, upto->0, rule_in->0,
B                         rule_fae->0, concat_fae->0, concat_fae_or->0
I I Fri Aug 31 16:10:10 2007
I MPI<c>9#3 Peak buffer usage: 5 (@ 64 KB)
S server @>SSRV:ides_I04_00@< appears or changes (state 1)
S server @>SSRV:ides_I04_00@< appears or changes (state 1)
S server @>SSRV:ides_I04_01@< appears or changes (state 1)
E E Fri Aug 31 16:10:11 2007
E Replication is disabled
N N Fri Aug 31 16:10:28 2007
N login/password_change_for_SSO : 1 -> 1
B B Fri Aug 31 16:10:38 2007
B table logging switched off for all clients
B B Fri Aug 31 16:10:41 2007
B dbmyclu : info : my major identification is 3232245831, minor one 0.
B dbmyclu : info : Time Reference is 1.12.2001 00:00:00h GMT.
B dbmyclu : info : my uuid is 96AAC2654435DC46AFA4C31629BE366F.
B dbmyclu : info : current optimistic cluster level: 3
B dbmyclu : info : pessimistic reads set to 2.
S S Fri Aug 31 16:15:55 2007
S found spool memory service RSPO-ACTIONS at 1DF34B50
M M Fri Aug 31 16:20:14 2007
M call semaphore clean-up function ...
M ***LOG Q0E=> DpSigGenHandler, Exception (c0000005) [dpnttool.c   462]
M -
C-STACK -
SAP (R) - R/3(TM) Callstack, Version 1.0
Copyright (C) SAP AG. All rights reserved.
Application exception occurred:
Exception : c0000005 (Access Violation)
App       : disp+work.EXE (pid=1680)
When      : 8/31/2007 16:20:14.837
Threads   : 2
Computer Name       : IDES
User Name           : SAPServiceI04
Number of Processors: 2
Processor Type: x86 Family 15 Model 6 Stepping 4
Windows Version     : 5.2 Current Build: 3790
State Dump for Thread Id 9cc
eax=00000000 ebx=00000000 ecx=00000014 edx=00000000 esi=003860ec edi=003860c0
eip=7c82ed54 esp=0300daa8 ebp=0300dab8 iopl=0         nv up ei pl nz ac pe nc
cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000             efl=00000212
function : MmxFree2
       00f35dde 2b0568e59701 sub eax,[MmxUheaderSz (0197e568)] ds:0197e568=00000010
       00f35de4 50               push    eax
       00f35de5 68dd000000       push    0xdd
       00f35dea ffb4246c010000   push    dword ptr [esp+0x16c] ss:0300dc14=7c82f9dd
       00f35df1 e890ac1200       call    memset (01060a86)
       00f35df6 83c40c           add     esp,0xc
       00f35df9 8b4308           mov     eax,[ebx+0x8]          ds:0300d006=2bf38b08
       00f35dfc 8bf3             mov     esi,ebx
       00f35dfe 2b730c           sub     esi,[ebx+0xc]          ds:0300d006=2444890c
       00f35e01 89442418         mov     [esp+0x18],eax         ss:0601aaaf=00000000
FAULT-> 00f35e05 f60601           test    byte ptr [esi],0x1           ds:003860ec=08
       00f35e08 7513             jnz     MmxFree2+0x4cf (00f35e1d)
       00f35e0a 8bce             mov     ecx,esi
       00f35e0c e814a7ffff       call    MmxIBlockRemove (00f30525)
       00f35e11 8b4308           mov     eax,[ebx+0x8]          ds:0300d006=08460108
       00f35e14 014608           add     [esi+0x8],eax          ds:033930f2=00000000
       00f35e17 89742414         mov     [esp+0x14],esi         ss:0601aaaf=00000000
       00f35e1b 8bde             mov     ebx,esi
       00f35e1d 8b7308           mov     esi,[ebx+0x8]          ds:0300d006=f6f30308
       00f35e20 03f3             add     esi,ebx
       00f35e22 f60601           test    byte ptr [esi],0x1           ds:003860ec=08
       00f35e25 750d             jnz     MmxFree2+0x4e6 (00f35e34)
--> Stack Back Trace <--
FramePtr ReturnAd Param#1 Param#2 Param#3 Param#4 Function Name
0300e648 00746014 3cc00548 3d07d010 06751220 00000000 disp+work!MmxFree2 [mmxx.c (2440)]
0300e668 006450a7 00000000 00000001 3cc88e78 3cc485e8 disp+work!ab_sqlsclose [absapsql.c (8104)]
0300e690 006466c6 00000013 00750af1 00000000 000000cd disp+work!ab_popbst [abstacks.c (4763)]
0300e698 00750af1 00000000 000000cd 00000000 01c720fa disp+work!ab_poprsql [abstacks.c (1167)]
0300e6cc 006e0f51 00000000 3d170778 00000000 00f00105 disp+work!ab_jsqls [absapsql.c (1306)]
0300e770 00766be4 3d1715b3 3d170778 00000000 01afb3a4 disp+work!ab_extri [abextri.c (431)]
0300e784 007ebf1c 00000000 7c36a42b 000004b6 00571b1a disp+work!ab_xevent [abrunt1.c (261)]
0300e794 00571b1a 3d171080 0000002e 3d170778 3d17139a disp+work!ab_dstep [abdynpro.c (460)]
0300e7bc 005740de 3d170778 3d170778 7c36a42b 00000000 disp+work!dynpmcal [dymainstp.c (2312)]
0300e7d4 00573680 3d17139a 3d170778 00000003 0300fdcc disp+work!dynppai0 [dymainstp.c (1043)]
0300e7f0 00549340 3d170778 00000002 00000001 00000000 disp+work!dynprctl [dymainstp.c (350)]
0300fdcc 004747f4 00000002 0300fe74 00000001 00497626 disp+work!dynpen00 [dymain.c (1375)]
0300fddc 00497626 00000002 00000000 003860a8 00000002 disp+work!Thdynpen00 [thxxhead.c (4353)]
0300feec 004979e0 00000001 7ffd4000 00000000 00000000 disp+work!TskhLoop [thxxhead.c (4117)]
0300ff04 00421d07 00000000 00000000 0300ff60 00401059 disp+work!tskhstart [thxxhead.c (1038)]
0300ff14 00401059 00000003 003860a8 00000001 00000000 disp+work!DpMain [dpxxdisp.c (1009)]
0300ff60 01060bcf 00000003 003860a8 003828f8 0152d000 disp+work!main [thxxanf.c (58)]
0300ffc0 77e523e5 00000000 00000000 7ffd4000 80a56be3 disp+work!mainCRTStartup [crtexe.c (398)]
0300fff0 00000000 01060a8c 00000000 00905a4d 00000003 kernel32!IsProcessorFeaturePresent
State Dump for Thread Id d2c
eax=0000005e ebx=00000103 ecx=00000010 edx=000719bb esi=00000000 edi=00000000
eip=7c82ed54 esp=04a1feb0 ebp=04a1fef4 iopl=0         nv up ei pl zr na po nc
cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000             efl=00000246
function : KiFastSystemCallRet
       7c82ed54 c3               ret
       7c82ed55 8da42400000000   lea     esp,[esp]              ss:04a1feb0=7c821514
       7c82ed5c 8d642400         lea     esp,[esp]              ss:07a2ceb7=????????
--> Stack Back Trace <--
FramePtr ReturnAd Param#1 Param#2 Param#3 Param#4 Function Name
04a1fef4 00fc37ec 000006ac 00000000 00000000 0038cd48 ntdll!KiFastSystemCallRet
04a1ff84 7c349565 00000000 00000000 00000000 0038cbd0 disp+work!SigIMsgFunc [signt.c (559)]
04a1ffb8 77e6608b 0038cbd0 00000000 00000000 0038cbd0 MSVCR71!endthreadex
04a1ffec 00000000 7c3494f6 0038cbd0 00000000 00000000 kernel32!GetModuleFileNameA
M -
M M Fri Aug 31 16:20:16 2007
M call clean-up function ...
M in_ThErrHandle: 1
M ThSigHandler: signal (step 4, th_errno 11, action 4)
M M Info for wp 0
M M    stat = 4
M    reqtype = 1
M    act_reqtype = 1
M    rq_info = 0
M    tid = 9
M    mode = 0
M    len = 787
M    rq_id = 423
M    rq_source = 1
M    last_tid = 9
M    last_mode = 0
M    int_checked_resource(RFC) = 0
M    ext_checked_resource(RFC) = 0
M    int_checked_resource(HTTP) = 0
M    ext_checked_resource(HTTP) = 0
M    report = >                                        <
M    action = 0
M    tab_name = >                              <
M M Modeinfo for User T9/M0
M M    tm state = 2
M    uid = 13
M    term type = 0x4
M    display = 0x8
M    cpic_no = 0
M    cpic_idx = -1
M    usr = >ABAP1       <
M    terminal = >DDDC393             <
M    client = >120<
M    conversation_ID = >        <
M    appc_tm_conv_idx = -1
M    imode = 1
M    mode state = 0x12
M    task_type = ZTTADIA
M    th_errno = 11
M    rollout_reason = 1
M    last_rollout_level = 7
M    async_receives = 0
M    cpic_receive = 0
M    em handle = 0
M    roll state = 4
M    abap state = 4
M    em state = 3
M    eg state = 1
M    spa state = 3
M    enq state = 0
M    next hook = T-1/U-1/M255
M    master hook = T-1/U-1/M255
M    slave hook = T-1/U-1/M255
M    debug_tid = 255
M    debug_mode = 0
M    mode type = 0x1
M    debug = 0
M    tcode = >ME21N               <
M    client conversation_ID = >        <
M    server conversation_ID = >        <
M    lock = 0
M    max enq infos = 9
M    act enq infos = 2
M    em_hyper_hdl = 57F03BD8
M    plugin_info = NULL
M    act_plugin_hdl = -1
M    act_plugin_no = 0
M    max_plugin_no = 0
M M Adresse   Offset Data from input buffer
M -
M 054A7D70 000000 00000000 00000000 01502700 00000000 |.........P'.....|
M 054A7D80 000016 00000000 0000009f 74100623 00170000 |........t..#....|
M 054A7D90 000032 04880131 31363000 77696e64 6f77732d |...1160.windows-|
M 054A7DA0 000048 31323532 00100409 00033731 3010041d |1252......710...|
M 054A7DB0 000064 00013010 040f0004 000012ad 10041900 |..0.............|
M 054A7DC0 000080 02000010 05010016 000d0000 000d002b |...............+|
M 054A7DD0 000096 a1001fa2 00000000 00000000 0000100c |................|
M 054A7DE0 000112 08001000 00029f00 00047400 00029f00 |..........t.....|
M 054A7DF0 000128 00047410 0a010009 00000000 00000000 |..t.............|
M 054A7E00 000144 00100a03 00090100 00000000 78001f10 |............x...|
M 054A7E10 000160 0a030009 03000900 00007800 0a100a03 |..........x.....|
M 054A7E20 000176 00090200 00000300 75000a10 0a030009 |........u.......|
M 054A7E30 000192 01000000 00007500 0a100a05 00090100 |......u.........|
M 054A7E40 000208 00000000 75000910 090e00c8 00c80000 |....u...........|
M 054A7E50 000224 00000075 00090000 23000700 0200000c |...u....#.......|
M 054A7E60 000240 01000000 00002300 82003c00 00000003 |......#...<.....|
M 054A7E70 000256 00070000 00070000 00000000 00000000 |................|
M 054A7E80 000272 00000000 00000000 00020005 00020002 |................|
M 054A7E90 000288 000c0014 00110003 0001000a 000e0005 |................|
M 054A7EA0 000304 00060003 000a000f 000c0008 000a000c |................|
M 054A7EB0 000320 000c0008 00030003 0002000a 0005000a |................|
M 054A7EC0 000336 0005000a 0005000a 00050005 00011100 |................|
M 054A7ED0 000352 11001100 11001100 11001100 11001100 |................|
M 054A7EE0 000368 11001100 11001100 11001100 11001100 |................|
M 054A7EF0 000384 11001100 11001100 11001100 11001100 |................|
M 054A7F00 000400 11001100 11001100 11001100 11001100 |................|
M 054A7F10 000416 11001100 100c0200 18000000 07000000 |................|
M 054A7F20 000432 23000000 07000000 00000000 00000000 |#...............|
M 054A7F30 000448 00100909 00180001 00077920 20202020 |..........y     |
M 054A7F40 000464 20202020 20202020 31303030 0000100a |        1000....|
M 054A7F50 000480 01000900 00000000 00000000 100a0300 |................|
M 054A7F60 000496 09010000 00000078 001f100a 03000902 |.......x........|
M -
M M *****************************************************************************
M *
M * LOCATION    SAP-Server ides_I04_00 on host ides (wp 0)
M * ERROR       ThSigHandler: signal
M *
M * TIME        Fri Aug 31 16:20:16 2007
M * RELEASE     640
M * COMPONENT   Taskhandler
M * VERSION     1
M * RC          11
M * MODULE      thxxhead.c
M * LINE        9555
M * COUNTER     3
M *
M *****************************************************************************
M M PfStatDisconnect: disconnect statistics
M Entering TH_CALLHOOKS
M ThCallHooks: call hook >SAP-Trace buffer write< for event BEFORE_DUMP
M TrThHookFunc: called for WP dump
M ThCallHooks: call hook >ThrSaveSPAFields< for event BEFORE_DUMP
M ThrSaveSPAFields: save spa fields
M Entering ThSetStatError
C SQLBREAK: DBSL_CMD_SQLBREAK: CbOnCancel was set. rc: 1 BREAK_REQUESTED
M ThIErrHandle: don't try rollback again
M ThIErrHandle: call ThrCoreInfo
M ThDelEnqInfo: del enq_own >20070831161118747000000000ides............................</1
M ThDelEnqInfo: act enq info: 1
M ThDelEnqInfo: del enq_own >20070831161118747000010000ides............................</2
M ThDelEnqInfo: act enq info: 0
A TH VERBOSE LEVEL FULL
C Fri Aug 31 16:20:17 2007
C SQLBREAK: BREAK_REQUESTED upgraded to BREAK_IN_PROGRESS sloledb.cpp 4187
M Fri Aug 31 16:20:18 2007
M SosSearchAnchor: search anchor for 4
M ThIErrHandle: Entering ThReplyToMsg
M ThIErrHandle: Entering ThErrHdlUser
M ThErrHdlUser: set th_errno (11)
M ThErrHdlUser: save context
M ThSaveContext: roll out
M ThRollOut: roll out T9/U13/M0 (level=7, short_roll_out=0)
M ThRollOut: call rrol_out (1)
M ThRollOut: act roll state = DP_ROLLED_OUT
M ThRollOut: roll level <> 0, don't call ab_rollout
M ThRollOut: full roll out of U13 M0 I1 (Level 7) ok
M ThCheckEmMagic: check em magic at 3CC00A80 for T9/M0/I1
M ThCheckEmMagic: em magic at 3CC00A80 for T9/M0/I1 o.k.
M ThEmContextDetach2: detach T9/M0 from em memory (em_hdl=0, force=0)
M ThEmContextDetach2: reset local em info
B Disconnecting from ALL connections:
B Wp Hdl ConName          ConId     ConState     TX PRM RCT MAX OPT Date     Time   DBHost         B 000 000 R/3              000000000 ACTIVE       YES YES NO 255 255 20070831 160937 IDES           C Rollback Work (0)
B Disconnected from connection 0
B statistics db_con_commit (com_total=149, com_tx=34)
B statistics db_con_rollback (roll_total=1, roll_tx=0)
M ***LOG Q02=> wp_halt, WPStop (Workproc 0 1680) [dpnttool.c   357]
M return from clean-up function ...
trc file: "dev_w0", trc level: 1, release: "640"
ACTIVE TRACE LEVEL           1
ACTIVE TRACE COMPONENTS      all, M
B B Fri Aug 31 16:20:36 2007
B create_con (con_name=R/3)
B Loading DB library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' ...
B Library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' loaded
B Version of 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll' is "640.00", patchlevel (0.26)
B New connection 0 created
M systemid   560 (PC with Windows NT)
M relno      6400
M patchlevel 0
M patchno    25
M intno      20020600
M make:      multithreaded, ASCII
M pid        2460
M
M ***LOG Q0Q=> tskh_init, WPStart (Workproc 0 2460) [dpxxdisp.c   1160]
I MtxInit: -2 0 0
M DpSysAdmExtCreate: ABAP is active
M DpSysAdmExtCreate: JAVA is not active
M DpShMCreate: sizeof(wp_adm)        7456    (828)
M DpShMCreate: sizeof(tm_adm)        2219848    (11044)
M DpShMCreate: sizeof(wp_ca_adm)        18000    (60)
M DpShMCreate: sizeof(appc_ca_adm)    6000    (60)
M DpShMCreate: sizeof(comm_adm)        192000    (384)
M DpShMCreate: sizeof(vmc_adm)        0    (320)
M DpShMCreate: sizeof(wall_adm)        (22440/34344/56/100)
M DpShMCreate: SHM_DP_ADM_KEY        (addr: 05230040, size: 2506248)
M DpShMCreate: allocated sys_adm at 05230040
M DpShMCreate: allocated wp_adm at 052317A8
M DpShMCreate: allocated tm_adm_list at 052334C8
M DpShMCreate: allocated tm_adm at 052334F0
M DpShMCreate: allocated wp_ca_adm at 05451438
M DpShMCreate: allocated appc_ca_adm at 05455A88
M DpShMCreate: allocated comm_adm_list at 054571F8
M DpShMCreate: allocated comm_adm at 05457210
M DpShMCreate: allocated vmc_adm_list at 05486010
M DpShMCreate: system runs without vmc_adm
M DpShMCreate: allocated ca_info at 05486038
M DpShMCreate: allocated wall_adm at 05486040
X EmInit: MmSetImplementation( 2 ).
X <ES> client 0 initializing ....
X Using implementation std
M <EsNT> Memory Reset enabled as NT default
X ES initialized.
M M Fri Aug 31 16:20:37 2007
M calling db_connect ...
C Thank You for using the SLOLEDB-interface
C Using dynamic link library 'C:\usr\sap\I04\SYS\exe\run\dbmssslib.dll'
C dbmssslib.dll patch info
C    patchlevel   0
C    patchno      26
C    patchcomment MSSQL: GetNextMsst1 error (754819)
C np:(local) connection used on IDES
C Using Provider SQLNCLI
C Provider Release:9.00.1399.06
C C Fri Aug 31 16:20:38 2007
C Using Provider SQLNCLI
C Cache sizes: header 52 bytes, 20000 names (26720000 bytes), 1000 dynamic statements (5432000 bytes), total 32152052 bytes
C Using shared procedure name cache IDES_I04I04_I04_MEM initialized by another process.
C Connected to db server : [IDES] server_used : [np:(local)], dbname: I04, dbuser: i04
C pn_id:IDES_I04I04_I04
B Connection 0 opened
B Wp Hdl ConName          ConId     ConState     TX PRM RCT MAX OPT Date     Time   DBHost         B 000 000 R/3              000000000 ACTIVE       NO YES NO 255 255 20070831 162037 IDES           C The IRow interface is supported by this OLEDB provider
M db_connect o.k.
I MtxInit: 0 0 0
M SHM_PRES_BUF            (addr: 098E0040, size: 4400128)
M SHM_ROLL_AREA        (addr: 68200040, size: 160432128)
M SHM_PAGING_AREA        (addr: 09D20040, size: 72351744)
M SHM_ROLL_ADM            (addr: 0E230040, size: 1602056)
M SHM_PAGING_ADM        (addr: 0E3C0040, size: 525344)
M ThCreateNoBuffer        allocated 320144 bytes for 1000 entries at 0E450040
M ThCreateNoBuffer        index size: 3000 elems
M ThCreateVBAdm        allocated 7424 bytes (50 server) at 0E4A0040
X EmInit: MmSetImplementation( 2 ).
X <ES> client 0 initializing ....
X Using implementation std
X ES initialized.
B db_con_shm_ini: WP_ID = 0, WP_CNT = 9
B dbtbxbuf: Buffer TABL (addr: 134C00C8, size: 30000128, end: 1515C4C8)
B dbtbxbuf: Buffer TABLP (addr: 0F3000C8, size: 10240000, end: 0FCC40C8)
B dbexpbuf: Buffer EIBUF (addr: 151600D0, size: 4194304, end: 155600D0)
B dbexpbuf: Buffer ESM   (addr: 155700D0, size: 4194304, end: 159700D0)
B dbexpbuf: Buffer CUA   (addr: 0FCE00D0, size: 3072000, end: 0FFCE0D0)
B dbexpbuf: Buffer OTR   (addr: 159800D0, size: 4194304, end: 15D800D0)
M rdisp/reinitialize_code_page -> 0
M icm/accept_remote_trace_level -> 0
C Using Provider SQLNCLI
S *** init spool environment
S initialize debug system
T Stack direction is downwards.
T debug control: prepare exclude for printer trace
T new memory block 15EF7370
S spool kernel/ddic check: Ok
S using table TSP02FX for frontend printing
S 1 spool work process(es) found
S frontend print via spool service enabled
S printer list size is 150
S printer type list size is 50
S queue size (profile)   = 300
S hostspool list size = 3000
S option list size is 30
S      found processing queue enabled
S found spool memory service RSPO-RCLOCKS at 1DEF0098
S doing lock recovery
S setting server cache root
S found spool memory service RSPO-SERVERCACHE at 1DEF02C8
S    using messages for server info
S size of spec char cache entry: 165020 bytes (timeout 100 sec)
S size of open spool request entry: 1152 bytes
S immediate print option for implicitely closed spool requests is disabled
A A -PXA--
A PXA INITIALIZATION
A PXA: Fragment Size too small: 195 MB, reducing # of fragments
A System page size: 4kb, admin_size: 11476kb.
A Attached to PXA (address 24550040, size 400000K)
A abap/pxa = shared protect gen_remote
A PXA INITIALIZATION FINISHED
A -PXA--
A A ABAP ShmAdm attached (addr=56AF9000 leng=20955136 end=57EF5000)
A >> Shm MMADM area (addr=56E610E0 leng=134752 end=56E81F40)
A >> Shm MMDAT area (addr=56E82000 leng=17248256 end=57EF5000)
A RFC Destination> destination ides_I04_00 host ides system I04 systnr 0 (ides_I04_00)
A RFC Options> H=ides,S=00
A RFC FRFC> fallback activ but this is not a central instance.
A   A RFC rfc/signon_error_log = -1
A RFC rfc/dump_connection_info = 0
A RFC rfc/dump_client_info = 0
A RFC rfc/cp_convert/ignore_error = 1
A RFC rfc/cp_convert/conversion_char = 23
A RFC rfc/wan_compress/threshold = 251
A RFC rfc/recorder_pcs not set, use defaule value: 1
A RFC rfc/delta_trc_level not set, use default value: 0
A RFC rfc/no_uuid_check not set, use default value: 0
A RFC Method> initialize RemObjDriver for ABAP Objects
A Hotpackage version: 38
M ThrCreateShObjects        allocated 9394 bytes at 0FFD0040
N SsfSapSecin: putenv(SECUDIR=C:\usr\sap\I04\DVEBMGS00\sec): ok
N N =================================================
N === SSF INITIALIZATION:
N ===...SSF Security Toolkit name SAPSECULIB .
N ===...SSF trace level is 0 .
N ===...SSF library is C:\usr\sap\I04\SYS\exe\run\sapsecu.dll .
N ===...SSF hash algorithm is SHA1 .
N ===...SSF symmetric encryption algorithm is DES-CBC .
N ===...sucessfully completed.
N =================================================
N MskiInitLogonTicketCacheHandle: Logon Ticket cache pointer retrieved from shared memory.
N MskiInitLogonTicketCacheHandle: Workprocess runs with Logon Ticket cache.
W =================================================
W === ipl_Init() called
W    ITSP Running against db release 620!
W    ITSP Disable Kernel Web GUI functionality
W === ipl_Init() returns 2, ITSPE_DISABLED: Service is disabled (sapparam)
W =================================================
M ThCheckPrevUser: clean previous user T9/U13/M0
M M Modeinfo for User T9/M0
M M    tm state = 2
M    uid = 13
M    term type = 0x4
M    display = 0x8
M    cpic_no = 0
M    cpic_idx = -1
M    usr = >ABAP1       <
M    terminal = >DDDC393             <
M    client = >120<
M    conversation_ID = >        <
M    appc_tm_conv_idx = -1
M    imode = 1
M    mode state = 0x12
M    task_type = ZTTADIA
M    th_errno = 11
M    rollout_reason = 1
M    last_rollout_level = 7
M    async_receives = 0
M    cpic_receive = 0
M    em handle = 0
M    roll state = 3
M    abap state = 3
M    em state = 2
M    eg state = 1
M    spa state = 3
M    enq state = 0
M    next hook = T-1/U-1/M255
M    master hook = T-1/U-1/M255
M    slave hook = T-1/U-1/M255
M    debug_tid = 255
M    debug_mode = 0
M    mode type = 0x1
M    debug = 0
M    tcode = >ME21N               <
M    client conversation_ID = >        <
M    server conversation_ID = >        <
M    lock = 0
M    max enq infos = 9
M    act enq infos = 0
M    em_hyper_hdl = 57F03BD8
M    plugin_info = NULL
M    act_plugin_hdl = -1
M    act_plugin_no = 0
M    max_plugin_no = 0
M C The IRow interface is supported by this OLEDB provider
M ***LOG R47=> ThResFree, delete (001023) [thxxmode.c   1283]

I Got the same problem but at that time i have installed GUI of lower version. WHen i have upgraded the GUI it worked fine. Better you check once the SAPGUI configuration.

Telnet session not working in OEL -5

Telnet session not working in OEL -5
==============================
1. Installed xinetd and telnet-server packages on the box.
2. Enabled the xinetd service.
# service xinetd start
# chkconfig xinetd on
Telnet still not working. Please help.
Lily.

Re-ran the /etc/init.d/xinetd restart command. Telnet cannot connect and this is what I get:
Unencrypted connection refused. Goodbye.
Below is the telnet.cfg
==================
# default: on
# description: The telnet server serves telnet sessions; it uses \
#     unencrypted username/password pairs for authentication.
service telnet
     flags          = REUSE
     socket_type     = stream
     wait          = no
     user          = root
     server          = /usr/sbin/in.telnetd
     log_on_failure     += USERID
     disable          = no
===================

ERROR MESSAGE sap system manager:work process restarted, session terminated

Hi,
i am a beginer in SAP administration, users are getting this error message and i have done all my research and not able to resolve this issue. Here are the details
SAP Version :ideas 4.7
Database :Oracle
OS : windows 2003
Module user is working on MM
user working on it is a Super user with all the permissions
SAP is configure to run under the European date and decimal format.
I have never done any database administration on it, it is a new install and has been rarely used.
User creates a RFQ and when he tries saving it , seems like for the first time after either restarting the macine or restarting the service it might work and at time it might not, this is a very sporadic error and most of the times it crashes out with the message "sap system manager:work process restarted, session terminated" and kicks the user out of the session.
Below are the details of the error message from ST22 :
name of the runtime error : system_core_dumped
below are the details of the error message and its resoltion as suggested by sap help :
========
Runtime Errors         SYSTEM_CORE_DUMPED
       Occurred on     01.02.2008 at 07:52:19
Process terminated by signal " ".
What happened?
The current ABAP program had to be terminated because the
ABAP processor detected an internal system error.
The current ABAP program "SAPLCLSC" had to be terminated because the ABAP
processor discovered an invalid system state.
What can you do?
                                                                                Make a note of the actions and input which caused the error.
To resolve the problem, contact your SAP system administrator.
You can use transaction ST22 (ABAP Dump Analysis) to view and administer
termination messages, especially those beyond their normal deletion
date.
Error analysis
An SAP System process was terminated by an operating system signal.
                                                                                Possible reasons for this are:
1. Internal SAP System error.
2. Process was terminated externally (by the system administrator).
           Last error logged in SAP kernel
                                                                                Component............ "Taskhandler"
Place................ "SAP-Server server1_DEV_00 on host server1 (wp 1)"
Version.............. 1
Error code........... 11
Error text........... "ThSigHandler: signal"
Description.......... " "
System call.......... " "
Module............... "thxxhead.c"
Line................. 9555
How to correct the error
The SAP System work directory (e.g. /usr/sap/c11/D00/work ) often
contains a file called 'core'.
Save this file under another name.
If you cannot solve the problem yourself, please send the
following documents to SAP:
1. A hard copy print describing the problem.
   To obtain this, select the "Print" function on the current screen.
                                                                                2. A suitable hardcopy prinout of the system log.
   To obtain this, call the system log with Transaction SM21
   and select the "Print" function to print out the relevant
   part.
3. If the programs are your own programs or modified SAP programs,
   supply the source code.
   To do this, you can either use the "PRINT" command in the editor or
   print the programs using the report RSINCL00.
4. Details regarding the conditions under which the error occurred
   or which actions and input led to the error.
System environment
SAP Release.............. " "
Application server....... " "
Network address.......... " "
Operating system......... " "
Release.................. " "
Hardware type............ " "
Character length......... " " Bits
Pointer length........... " " Bits
Work process number...... " "
Short dump setting....... " "
Database server.......... " "
Database type............ " "
Database name............ " "
Database owner........... " "
Character set............ " "
SAP kernel............... " "
Created on............... " "
Created in............... " "
Database version......... " "
Patch level.............. " "
Patch text............... " "
Supported environment....
Database................. " "
SAP database version..... " "
Operating system......... " "
User, transaction...
Client.............. " "
User................ " "
Language key........ " "
Transaction......... "ME41 "
Program............. "SAPLCLSC"
Screen.............. "SAPMM06E 0320"
Screen line......... 71
Information on where termination occurred
The termination occurred in the ABAP program "SAPLCLSC" in "EXECUTE_SELECT".
The main program was "SAPMM06E ".
The termination occurred in line 131 of the source code of the (Include)
program "LCLSCF2G"
of the source code of program "LCLSCF2G" (when calling the editor 1310).
=============
i even tried increasing the dialog processes but with no use.The same error occurs.
I appreciate every one of help i can get, i am working on a deadline which is tomorrow evening to resovle this issue, any kind of help is highly appreciated.
thanks
mudessir.

Hi
   follow correction method suggested in this dump,
" The SAP System work directory (e.g. /usr/sap/c11/D00/work ) often
contains a file called 'core'. Save this file under another name."
have you done this?
with regards,
raj.
<i>pls, award points</i>

PSADELETE process failure due to Internal Session Terminated.

Hi,
We have a PSADELETE process in Process chain which failed because of Internal Session Terminated error.
Now when i am trying to Repeat the process it is giving message Cannot activate job BI_PROCESS_PSADELETE (return code 8)
and the process is not starting again.
Please guide me the solution.
Thanks
Singh

Can you check for more details in SM37 for the cancelled job log .
Do you have authorization to run 'repeat step ' ?
or display psadelete variant - identify the infopack/psa tables-> u can delete manually psa requests
Edited by: Srinivas on Jul 18, 2010 5:22 PM

ORACLE server session terminated by fatal error

Hi,
When i try to startup my database(10g), i am getting this error after database monted.
ORA-00603: ORACLE server session terminated by fatal error.
(Startup nomount is ok)
conn /as sysdba
Total System Global Area 1048576000 bytes
Fixed Size 1223392 bytes
Variable Size 343934240 bytes
Database Buffers 700448768 bytes
Redo Buffers 2969600 bytes
Database mounted.
ORA-00603: ORACLE server session terminated by fatal error
Alert.log:
Errors in file /u01/app/oracle/product/10.2.0/db_1/admin/db/udump/db_ora_9917.trc:
ORA-00603: ORACLE server session terminated by fatal error
ORA-00600: internal error code, arguments: [4194], [24], [14], [], [], [], [], []
ORA-00600: internal error code, arguments: [4194], [24], [14], [], [], [], [], []
The trace file is 1,6GB(!)
Trace file:
----- Redo read statistics for thread 1 -----
Read rate (ASYNC): 26Kb in 0.78s => 0.03 Mb/sec
Total physical reads: 4096Kb
Longest record: 0Kb, moves: 0/62 (0%)
Change moves: 35/122 (28%), moved: 0Mb
Longest LWN: 14Kb, moves: 0/13 (0%), moved: 0Mb
Last redo scn: 0x0000.31539752 (827561810)
NO VALID LOG MEMBER FOR SEQ# 20884 OF THREAD 1!
NO VALID LOG MEMBER FOR SEQ# 20883 OF THREAD 1!
*** 2011-01-06 06:18:51.782
ksedmp: internal or fatal error
ORA-00600: internal error code, arguments: [4194], [56], [49], [], [], [], [], []
Current SQL statement for this session:
update service$ set name = :1, name_hash = :2, network_name = :3, creation_date = :4, creation_date_hash = :5, deletion_date = null, goal = :6, flags = :
----- Call Stack Trace -----
Thanks

Hello,
ORA-01194: file 1 needs more recovery to be consistent
ORA-01110: data file 1: '/u01/app/oracle/product/10.2.0/oradata/db/system01.dbf'The system01.dbf which belongs to the Tablespace SYSTEM is still inconsistent.
So, I think you'll need to start from a Backup and apply all the Archived Redo logs before the ORA-600 occured.
More over, try to open a Service Request to My Oracle Support and, send them all the Traces Files and Alert Log so that they can follow all the actions which has occured on this Database. You may need their help.
Best regards,
Jean-Valentin

Placing a telnet session within a java swing program

I was wondering if there was a way to maybe anchor a telnet session into a JPanel within a Java Swing program. Most of my users end up running a telnet session while using my Swing Program and I was hoping to find a way to bring the two together. If this is possible could someone point me in the right direction (like an online resource) that might show me how to do this.

You could use sockets and a TextArea and build your own simple telnet application.
Socket tutorial: http://java.sun.com/docs/books/tutorial/networking/sockets/index.html

Wired dot1X session termination

Hi all,
Question about wired dot1X session termination.
After a client successfully done on the wired dot1x authentication, my authZ rule is follow by the VLAN assignement whereby DHCP server will provision a client IP to the PC.
But when the client doing these 2 action:
01. after get connected, disable the IEEE 802.1x option on the PC Ethernet port setting
02. after get connected, disable, then enable the PC Ethernet port setting (bouncing)
I found out these 2 actions will still get the user in authorized state, because it is not link down or port-bounce action. Session still persist at client PC.
My question :
Anything i can configure either on the switch or ISE will automatic trigger an action like send an EAPOL-Logoff message, causing the switch port to change to the unauthorized state?
Thanks
Component in use:
client OS: window 7
PEAP-MsCHAP V2
authentication mode : iser or computer authetnication
no check on single sign on
no check remember credential for connection each time logged on
no check fallback to unauthorized network access
ISE 1.1.3 with patch 4
Switchport configuration
interface G0/1
switchporGt mode access
switchport access vlan 61
authentication port-control auto
dot1x pae authenticator
authentication host-mode multi-auth
authentication order dot1x
authentication priority dot1x mab
no shutdown
end

For #2 - The session should terminate and restart if the Ehternet adapter on the PC bounces. Are you saying that even though the user disables/enables the adapter, the session remains active in ISE/NAD?
For #1 - I am not really sure as I have never played with this before. My guess would be "No" because once ISE sends the "Access Accept" back to the NAD (your switch in this scenario), the NAD won't know if you are disabling 802.1x. The EAPoL conversation already took place so there is no more 802.1x type traffic coming in and out of the NAD/Client on that port.
I suppose you can set a re-autn and inactivity timer on both the NAD and ISE but keep in mind that it is not recommended for those timers to be set at low values (minimum 1 hour). Otherwise you could overwhelm your ISE servers depending on how large your environment is.
You will need to add the following commands on the switchport:
authentication periodic
authentication timer reauthenticate server
authentication timer inactivity server
Then in ISE you will need to set the re-auth and the idle timers under the "Authorization Profile"
Another thing to keep in mind is that you should control what your users can and cannot do on their workstations via GPO (Group Policy). In normal circumstances a regular user should not have the privileges to disable 802.1x or their Ethernet adapter :)
Hope this helps!
Thank you for rating helpful posts!

Run 6i form in a telnet session on a 32 bit Windows environment

Hi,
We have the following environment: 8.1.7 database, 9iDS Forms 6i (6.0.8.13.0) included. This is installed on 32 bit windows environment. We have wireless RF barcode scanners with TCP/IP connection. So they can connect to Unix box or a Windows telnet session. As we have Windows system we can connect this equipments to Windows through telnet session.
I heard and read in some topics that Forms 6i can run in character mode environment. But I didn't find any solution.
We would like to run forms as we can run svrmgrl for example on a telnet session.
My question is that it is possible to run 6i forms on charcater mode environment (telnet session) ? If so, what we need to do in the development or running phase (command line parameters for example).
Thanks in advance,
Attila

Forms 6i can run in Character mode in telnet - but this only applies to Unix ports of the product - they have an f60run executable as well as the Gui f60runm and the Web f60runw runtimes.
Windows only has GUI and Web versions.

Telnet session terminating

Similar Messages

Maybe you are looking for