Temp Monitor issue

I just did a clean install on my blackbook, and reinstalled the temp monitor 3.9 version.
Now the issue is that it does not read the processor temps but just the harddrive temp. Also it prompted me that I needed to install some intel drivers.
Problem is I clicked NO by accident. Is there anyway I can get the drivers again??
Does anyone know what these drivers were, or where I can download them??
Any input would be apreciated.

In the Temperature Monitor menu named "Monitor", there are two choices called "Install driver for extended x86 support" and "Uninstall..etc". If you haven't installed the driver, the install option should be available (with the other grayed out). Click to install.
It 's a kernel extension needed to read the CPU temps.

Similar Messages

  • It ALL works (mostly)!!! CPU Temp Monitor??

    Just finished assembling my new system and loading it up this weekend, and amazingly, it works. Even with CL3 ram it runs much faster than a P4 1.8A on SiS 645/DDR333 board I had. I am amazed at how big a difference there is in the way XP Pro loads and retrieves data and how smooth it sets up. I did not have to load ANY drivers! A huge step forward from 98SE.
      The only issue appears to be that the temperature monitor is out to lunch (So was my last board the SiS645 one, it did the exact same thing) for both CPU and Case. I installed a seperate case system to monitor temp and it gives me 22 deg C after I rearranged the airflow from the fans. I am thinking of drilling out the stock heatsink and inserting one of these temp monitors to real time monitor the CPU.
      Has anyone come up with a good way to really monitor CPU temps with this board??

    Hey,
       I loaded up MBM (after I figured out what it was and where to find it). It seems pretty good: The case reads 37 deg C (my independent sensor reads 27 deg and bios says 47) and CPU reads 47 deg (bios says 57).
       The real questions is : My -12 volts reads -6, and I have played with the settings to find the right sensor, and every sensor I select changes all the voltage readings. Is there a specific selection for readings that sets this up right?
       Also, I found a Lian-Li temp sensor with thin tape probes that is designed to be set between CPU/Heatsink to provide real time accurate monitoring for chips (theres two, so I plan on doing CPU and NB), so I will have real data instead of hoping it is right. (19.00 US). Nice little 3.5" or 5.25"  models avail in black, silver or beige.
    Nick

  • Trouble with color on Presario, No red tones on display. Not a monitor issue.

    Am experiencing trouble with color on Presario, model no. CQ5500F. Purchased a couple of years ago, and trouble was present immediately. Am getting no red tones - red items appear black or sometimes blue. Was told by HP that it was a monitor issue, and let computer slide out of warranty. installed new monitor today and problem still exists. Is this merely a display adjustment of some kind? Or will I have to pay HP their $99 for a one time fix? Any suggestions appreciated.

    Hello UncleBob62,
    It could be the display driver that is not properly working
    1. Click on the start icon
    2. Right click on computer and go to properties
    3. Select Device Manager
    4. Expand display adapters and right click on the video card driver and uninstall
    The computer screen will go blank
    On the keyboard press the windows key the right arrow key twice and then the letter R.
    At this point your computer is going to reboot. After the reboot Windows will install generic drivers for your video card. Do you still see a lack of red tones?
    If I have helped you in any way click the Kudos button to say Thanks.
    The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
    - Friendship is magical.

  • Multiple Monitor Issue

    Alright, so I have a 15" Macbook Pro with the dual graphics cards (GeForce 9600M GT and GeForce 9400M GT 256 version). It's the 2.66 intel processor one. Anyway, I've been trying to figure out this dual monitor issue that I've been having for a few days now. When I'm using the 9400M card and I plug into my mini displayport everything works just fine. This includes the VGA cord, the HDMI, as well as a standard Apple monitor. Now, when I switch over to the higher end graphics card, as soon as I plug into the mini displayport my screen goes black. And that's it. I can't do anything. I have to hold the power button down until the computer turns off.
    I've been searching for days in order to find an answer to this question or if anyone has ever had a similar problem and no one could help me. I even went to the genius bar and no one could help either. Keep in mind I've tried this in a variety of ways. I've plugged the monitor in after the computer was running, I've had it plugged in while the computer was turning on, and each time after the initial boot up everything goes black.
    To make matters worse, I originally came across this issue because I use Windows 7 on bootcamp and I wanted to use dual monitors within Windows. Bootcamp is only set to use the 9600M graphics card which is the one giving me all the heartache and apparently there's no way around it. If anyone has the slightest clue as to what's going on here or why it would be doing such a thing, let me know. Thanks.

    Jon: Thanks for answering those questions. Run the Apple Hardware Test that you'll find on one of the DVDs that came with your MBP. If any errors are reported, go back to the Genius Bar with the error codes reported by AHT and ask to have the machine repaired.
    If you have extended AppleCare protection, you have a TechTool Deluxe CD/DVD. You can also use that to test your hardware. If it reports any errors, take the exact wording and error codes from that report along with you to the GB, too.
    The problem is not with your three external displays or your cables, adapters, or your MBP's mini-Displayport, because they all work fine with the 9400M. The problem isn't some wrong contact that's being made momentarily as you insert the mini-Displayport plug into the port, because it occurs even when the cable is securely connected before starting up the computer. It seems to me the problem must reside either in your 9600M GT or in its connection to the mini-displayport.

  • Graphics card issue or monitor issue?

    Hello, i have a MacPro 2.66 w/ an ATI x1900 and a MacBookPro with th nVidia 8600
    i recently purchased a 28" Hanns-g Display which i upgraded from my 20" apple cinema display, im curious if this could be a graphic issue or a monitor issue:
    When i connect the 28" monitor to my ATI card (port 1) and boot into 10.4.10 (macPro) i noticed diagonal lines that seem to "scroll" (like an overscan line or something) on greyish and lighter backgrounds.
    tried it with the second port, same thing, it does it on all resolutions
    (it runs @ 1920x1200).
    when i boot into XP and try the same sites i did in 10.4.10 it doesnt do it at all, its as it should.
    I tried both VGA>DVI and HDMI>DVI to the ATI on OSX but it only does it with the HDMI>DVI connection under OSX, VGA looks fine.
    (btw my ati card is clean as a whistle, no dust or anything)
    However if i plug it into my MacBookPRo with hdmi>DVI it doesnt do that at all.
    so im wondering probably incompatible monitor or what?
    im looking to getting a 30" Apple Display but not if its gonna act up like that on my macpro, none of this appeared on my ACD 20".
    any suggestions or tips?
    thanks!

    im not experiencing scan line son my 30" ACD display under OSX or XP with my ATI, could be the monitor you are using, but if its not doing it with your MBP than.....idk
    sonds strange, try another gfx card or another macpro if possible.

  • Recommendations for server rack temp monitoring?

    Our server room isn't large, we only have one rack with two Xserves, an Xserve RAID and a few other things. But temperature is obviously a concern and I worry about the day when the portable AC unit kicks the bucket and I'm away from the office.
    Does anyone have recommendations some kind of temp monitoring device with email notifications, maybe web monitoring?

    At work, we use a rack-mount Senturion Environment Monitor, it monitors the temp, humidity, etc. It can send SMS and email alerts, and you can monitor it on the web, it just needs power and a network connection. We got it when our AC actually did kick the bucket and 50 servers overheated. :-/

  • Core temp monitor program for hp touchsmart 610-1250

    Hi,
    Re: HP TouchSmart 610-1250, 64 bit, Win 7.
    This is a new computer, my first all-in-one, and I want to monitor core temp. My CPU gadget tells me this has no core temp monitor system. Is it possible to download a monitor?
    As an all in one, I'm concerned about heat build up, since I'm using it all day.
    Any info is appreciated.
    Thanks
    A
    This question was solved.
    View Solution.

    Have you tried SIW? (System Information for Windows by Gabriel Topala) I highly recommend it. Go to the sensors page after you open it, and then It should tell you.
    Please give Kudos. What other kind of recognition could I get?
    Have I solved your problem? Mark solution as accepted.
    I try to hate Macintosh. I really do. But I can't bring myself to hate any electronic device.

  • Playing off the Timeline via firewire( XdCam pal) Monitoring Issues

    Hey,
    I have just switched to FCP and have found that when recording the from the FCP timeline manually via firewire into a Sony XDCam PDW530 I experience 4:3 flashes in the Camera monitor and viewfinder as the timeline plays down Video Transitions. All effects have been rendered (Blue line above transition)
    However the Camera appears to record correctly to disc. I played the recorded material from the camera via an XD deck into a wide screen monitor and all appears fine the 4:3 flashes are not present on transitions. play the disc back in the camera and the 4:3 flashes for the duration of the Video Transitions return????
    when playing out of the Camera via SDI and Analogue Composite outputs into a wide screen monitor all appears ok as well.
    It's a little odd that you cannot monitor the output correctly on the XDcam. If i change the pull down settings from 2323 to 2332 it monitors the transitions correctly but the video aspect is somewhere between 4:3 and 16:9.
    Shoot in 16:9 Capture DV Pal, Edit DV Pal, Playback Output Apple FireWire Pal (720 x 576)
    Any ideas????

    Thanks Shane,
    We have been down the PRINT TO VIDEO road with the same playback issues in the XD Camera's LCD screen. We still see the 4:3 transition on the 16:9 image when playing off the timeline / playing back the recorded media in the camera and viewing on cameras screen .
    I guess this is only a monitor issue. If you don't include any video effects it plays down 16:9 perfectly in the cameras monitor
    What is recorded onto the disc is fine.
    Also my understanding is the what's coming off the timeline is a DV stream so not sure how the GOP format comes into play. Recording onto a XD Cam off the timeline thru other edit programmes has never been an issue. I have come from Avid Pinnacle and the monitoring of transitions was never an issue when streaming back to the xdcam.
    Thanks

  • Windows Server 2012 R2 Session Host Server Temp Profile issue.

    HI,
    I successfully Deployed Windows server 2012 r2 Terminal services with High Availability.
    After Rebooting Session Host Server i am facing Temp Profile issue. After i Deleted registry and rebooting server and tried to login again but same popup message you have login with temp profile.
    Any suggestions or any hints would be GREATLY appreciated
    /HR

    how did you delete the profile?
    also are you using UPD disks?
    What errors are shown in the event log if any?
    Regards,
    Denis Cooper
    MCITP EA - MCT
    Help keep the forums tidy, if this has helped please mark it as an answer
    My Blog
    LinkedIn:

  • MSI GeForce 6600GT temp monitoring

       Hi, i was just wondering if there was a pre-modded / tested bios available that enables temp monitoring in MSI's 6600GT VTD-128. I didn't think i could hex it myself so i just wanted to know if anyone had success doing it.
    Thanks,
    ~Snikkle

    Hi you could check those sites like this :  Enabling Temperature Monitoring on the nVidia 6600GT
    but I wont recommend you to do that if you are don't know a lot about computers and updating/editing bios.
    kind regards
    and remember do it at your own risk.

  • Temp monitor for ppc?

    what cpu temp monitor can be used for ppc mac mini or ppc mac?
    using http://www.bresink.com/osx/TemperatureMonitor.html the widget one and i think that it is reporting the harddisk temp and not the cpu temp since it has the only option of "SMART Disk hardisk model here" and gave me a 45C-49C temp

    I don't think there is a CPU temperature sensor on the PPC mini.

  • Best temp monitor program for K8N and 6800GT?

    I'm looking for a temp monitoring program that will display the following temps:
    CPU
    Chipset (system)
    GPU
    Core Center is ok but it doesn't allow for precise history and it doesn't display GPU temp.

    The only thing I can suggest is a hardware thermistor and display, I have a GMC X-21 case which has a small temperature display on the font, and you can place the thermistor anywhere you like. I have it in between 2 fins on my CPU heatsink and it reads the temperature exactly the same as corecentre.

  • Preferred cpu temp monitor softy?

    what is the good cpu temp monitoring softy for 875pneo? i mean the accurate one. I've used aida and core center but yield different result. dont know which one to use... thnx!

    I have been using motherboard monitor for years and is simply the best freeware monitor around.  It even does OSD scripts with xml coding.
    Motherboad Monitor
    G16aByT3

  • Help enabling temp monitor on VGA

    i have an MSI G4TI4200 working perfectly for sometime overclocked to 310/640.not bad.....after taking off the heatsink on the VGA i found a temp diode next to the GPU so i wandered why it never worked.........any way i want to know how to enabled the temp monitor on my VGA so i can see it on my nvidia applet.......can i use that trick fo G6600 by altering the bios using the HEX editor and reflashing......i mean does that tirck work for all nvidia card.........any idea are appreciated thnx
    P4 2.6C OC to 3.2
    2xA-data ddr500 dual
    seagte sata hdd 80GB
    MSI G4TI4200 64mb 8x
    NEO 2 -PLS plat
    Vantec 400W psu

    i am using the 71.84 the latest one from Nvidia website...........but nothing shows in the tab plus i have the latest coolbits registry ..........that didnt help ether.........one could this mean.....that the temp diode on the VGA is just for decoration    .........or it doesnt work. I think it could be a Bios problem.....my Bios right now is A0 for the VGA maybe i need to flash it. Any ideas of how to do that thnx alot 

  • MSI 6600 GT question...Temp monitor on 6600GT?

    I'm about to return my XFX 6600GT because of problems. How is the MSI version of the card? Is the temp monitor available under Nvidia properties?

    Just my copy to another reply:
    I have the same card but use nVidia drivers to give me a temp read on the GPU.  I have loaded from scratch and like the nVidia settings screens because they give you more options.  Below is my overclock with MSI drivers and nVidia drivers.  The overclock is about the same so it depends on your use of the card...automated with MSI & DOT, manual with nVidia.  My GPU Temp read is around 47c to 48c.
    K8N SLI - winni 3000+ oc 220x3=660 HTT
    MSI 6600GT x1 oc 560/1.12 Ghz = nVidia Drivers only
    Corsair value RAM 512x2 oc 200:200 2.5,3,3,7 prime95 stable 2.7v 220 memspd
    3DMark05 = 3949  PCMark04 = 4052
    K8N SLI - winni 3000+ oc 218x3=654 HTT (MSI level 5 maxed DOT) with CnC enabled
    MSI 6600GT x1 oc 555/1.11 Ghz = MSI Drivers only (MSI level 6 maxed DOT)
    Corsair value RAM 512x2 oc 200:200 2.5,3,3,7 prime95 stable 2.7v 218 memspd
    3DMark05 = 3833  PCMark04 = 4023
    To get accurate temp reads on your CPU and system and much other stuff, I use Everest (www.lavalys.com) and with quick reboots it seems fairly accurate.  My CPU core is usually between 35c and 37c and my system temps are around the same.....................

Maybe you are looking for

  • HP Officejet Pro 8100 ePrinter & custom paper sizes

    Have found all the helpful instructions about creating new custom paper sizes in Windows 7. But am complete novice & need to buy a printer for a charity. Settled on this model because of good reviews but most work will be 1 document of custom paper s

  • I went from an iphone 5 to an iphone 5s and NONE of my new or older photos in PhotoStream will sync to my PC. WHY?

    Before I switched from a 5 to 5s, my photos has stopped "streaming" to my PC.  I would get every other photo and then just random photos would be added to the MyPhotoStream folder on my PC when I was connected to wi-fi... Now that I got my iPhone 5s,

  • ERROR: file can not be accessed or does not exist

    I have a client online at this very moment that just went on and did all their page edits... about 2 hours of work for him. He went to save the file & received the error "...file can not be accessed or does not exist, Error" (no error number or anyth

  • Can I import and view from a camara

    I was reading on the new that there are a few ways to import pictures from my Canon G5 camera. The two most common are the Belkin compact flash reader, or the apple iPod camera connector (I think it is called). the thing that plugs into the ipod and

  • Locale and language

    I am having trouble getting locales and languages to work as I would expect them to. I have created a tiny application (I'm a faces newbie still) and a bunch of localization files: message.properties messages_en.properties message_fr.properties messa