Temp monitoring for 5700 ultra

ok..1st off..i dont have a msi vid card..i have a PnY..fx5700 ultra...card runs fine..no issues(cept for an occational..."power supply not plugged in")..but my question is this..in the Nvidia card properties area..theres a spot that monitors my card core temp..and its set at 129 celceus...which is not possible...my case would be on fire if it ever got that hot..what i want to know is there any way to manually set the temp warning to a setting of my choosing..i mailed pny about it..and believe it or not..there answer was"make sure your fans plugged in"lol
i sat in utter amazement at the respone they gave me

ok...thx alot...im sure they know better then i do...it just seemed to me that was a bit high...id like the option of setting it to a temp of my own..but i guess its not possible...and i wanted to return the card to the store i bought it from..but in a rare case(i always put comp part reciept in the box it came from) i lost it    ..i can return it through pny...but i dont wanna deal with the hassle right now..if it fails completely...then ill return it and put my ti4400 back in..once again..thank you

Similar Messages

  • Temp monitor for ppc?

    what cpu temp monitor can be used for ppc mac mini or ppc mac?
    using http://www.bresink.com/osx/TemperatureMonitor.html the widget one and i think that it is reporting the harddisk temp and not the cpu temp since it has the only option of "SMART Disk hardisk model here" and gave me a 45C-49C temp

    I don't think there is a CPU temperature sensor on the PPC mini.

  • Temp. monitor for Neo4 SLI?

    Can anyone recommend me a program that's like Motherboard Monitor for the Neo4 SLI?  I'm looking for a program that will display the temps in the system tray.  Too bad MBM is discontinued 

    the current system temp monitor program i'm using is Systool. it autodetects your mobo and videocard. it has a whole bunch of other stuff too. it even detects videocard temps. check it out @ http://www.techpowerup.com/systool/
    there's ALOT more you can do with it too. but that's for you to find out.

  • Urgent question about two monitors for Sun Ultra 40 M2

    Hello,
    I feel extremely unhappy to ask you the following.
    I bought recently a Sun Utra 40 M2. I thought that with NVIDA Quadro FX1500 one could have two monitors as there are two DVI-D 's to connect with two monitors.
    But today I heard from SUN support that Sun does not support two monitors under SUN Solaris 10. It is possible with Linux on this SUN Ultra 40, but not with Solaris, so it was told to me.
    But: is this true? I still can not believe it.
    with friendly greetings,

    Hello,
    I see, with Windows it is possible just lik that and with Solaris one needs two cards.
    Well, it seems for a one man"s business customer like me: end of story.
    I still can not believe it that Sun would arrange this.
    I will wait and see.
    with friendly greetings,
    P_ter

  • Core temp monitor program for hp touchsmart 610-1250

    Hi,
    Re: HP TouchSmart 610-1250, 64 bit, Win 7.
    This is a new computer, my first all-in-one, and I want to monitor core temp. My CPU gadget tells me this has no core temp monitor system. Is it possible to download a monitor?
    As an all in one, I'm concerned about heat build up, since I'm using it all day.
    Any info is appreciated.
    Thanks
    A
    This question was solved.
    View Solution.

    Have you tried SIW? (System Information for Windows by Gabriel Topala) I highly recommend it. Go to the sensors page after you open it, and then It should tell you.
    Please give Kudos. What other kind of recognition could I get?
    Have I solved your problem? Mark solution as accepted.
    I try to hate Macintosh. I really do. But I can't bring myself to hate any electronic device.

  • Best temp monitor program for K8N and 6800GT?

    I'm looking for a temp monitoring program that will display the following temps:
    CPU
    Chipset (system)
    GPU
    Core Center is ok but it doesn't allow for precise history and it doesn't display GPU temp.

    The only thing I can suggest is a hardware thermistor and display, I have a GMC X-21 case which has a small temperature display on the font, and you can place the thermistor anywhere you like. I have it in between 2 fins on my CPU heatsink and it reads the temperature exactly the same as corecentre.

  • Recommendations for server rack temp monitoring?

    Our server room isn't large, we only have one rack with two Xserves, an Xserve RAID and a few other things. But temperature is obviously a concern and I worry about the day when the portable AC unit kicks the bucket and I'm away from the office.
    Does anyone have recommendations some kind of temp monitoring device with email notifications, maybe web monitoring?

    At work, we use a rack-mount Senturion Environment Monitor, it monitors the temp, humidity, etc. It can send SMS and email alerts, and you can monitor it on the web, it just needs power and a network connection. We got it when our AC actually did kick the bucket and 50 servers overheated. :-/

  • MSI FX 5700 Ultra problem with linux

    Hi,
    I know that linux are not officially suported by MSI VGA cards, but NVIDIA based VGA cards use to work under linux. I've got a problem with a recent purchase and until now I didn't found any answer.
    Here is my problem, if anyone here have an idea :
    I recently upgraded my video card Geforce 2 MX to a Geforce FX 5700 Ultra from MSI (FX 5700 Ultra TD128).
    I've an Athlon XP 2000,
    motherboard Gigabyte GA-7VAXP, 512 Mb,
    distrib Mandrake 9.2
    latest nvidia driver 5328
    At startup after installation, Mandrake detected a new hardware, but it was not the right card name. The video test failed and X (graphic mode) didn't start.
    Back to console mode, I discovered that even the console mode doesn't work properly : I have no cursor and the screen lines don't scroll up when the screen gets full (very hard to type commands or edit files).
    I checked the XF86Config-4 : for me it seems ok. Actually, it didn't change from the previous card.
    I've no errors in the XFree log (no lines with (EE)).
    I went to the MSI site to look for a newer bios version, but there is'nt.
    I tried both DVI and VGA connection with my LCD monitor, same thing.
    I also tried running Knoppix (liveCD distrib), same prob.
    I pasted below the message i've got on screen when I try to start X manually (this doesn't help much either) :
    XIO:  fatal IO error 104 (Connection reset by peer) on X server ":0.0"
          after 0 requests (0 known processed) with 0 events remaining.
    It seems to me that this graphic card simply doesn't work under linux.
    Thanks a lot for any help.

    To get  X to work with your LCD during the installation process append nofb as one of the installation options.
    I have a 17" LCD so you might like to compare the relevant sections in your XF86Config with these:
    Section "Module"
       Load  "dbe"
       Load  "extmod"
       Load  "fbdevhw"
       Load  "glx"
            Load  "dri"
       Load  "record"
       Load  "freetype"
       Load  "type1"
    EndSection
    (The Load "dri" gets removed prior to installing nvidia's Forceware drivers.)
    Section "Monitor"
       Identifier   "Monitor0"
       VendorName   "Monitor Vendor"
       ModelName    "CML174SX"
       DisplaySize  340   270
       HorizSync    24.0 - 80.0
       VertRefresh  56.0 - 75.0
       Option       "dpms"
    EndSection

  • Recommend anti-glare LCD monitor for MBP 13

    Hello, I need a decent quality antiglare type monitor to be the external monitor for graphics work with my MacBook Pro 13 inch unibody. I just tried an HP ZR24w but was not able to get it working. The monitor would light up for one second and my desktop showed, then it would immediately go dark. Apple support could not help, HP support  kept me on hold for 45 min. and then dropped my call.
    Unfortunately Apple no longer makes antiglare monitors for its graphics professional community. If they did I would buy an Apple monitor. I am currently using an old Apple Cinema Display but it has a bad case of creeping screen defects and looks terrible.
    Is anyone out there sucessfully using an external monitor with MBP that has an antiglare screen, does 1920 x 1200 res and has an IPS LCD?
    The usual suspects that people recommend for graphics work in the mid-range are Dell ultra-sharp and HP LP2475w. Since I do less graphics work than I used to I thought the ZR24w would be a good affordable option, however since I could not get it to work I am concerned that none of these other monitors will be compatible either. Buying and returning vis mail order is expensive... would really appreciate hearing what other people are using.
    Please let me know what connector you are using. I tried the ZR24w with both DVI and displayPort but neither of these options work for me. Apple tech support was stumped and blamed it on HP.
    Any thoughts?
    TIA!

    There should be a anti-glare option on ALL Mac's, however the 13" is certainly the next prime candidate for one given that they rolled out anti-glare for the 17" first, then the 15" next.

  • Guidelines for Health Monitoring for TimesTen

    This document provides some guidance on monitoring the health of a TimesTen
    datastore. Information is provided on monitoring the health of the
    datastore itself, and on monitoring the health of replication.
    There are two basic mechanisms for monitoring TimesTen:
    1. Reactive - monitor for alerts either via SNMP traps (preferred) or
    by scanning the Timesten daemon log (very difficult) and reacting
    to problms as they occur.
    2. Proactive - probe TimesTen periodically and react if problems, or
    potential problems, are detected.
    This document focusses on the second (proactive) approach.
    First, some basic recommendations and guidelines relating to monitoring
    TimesTen:
    1. Monitoring should be implemented as a separate process which maintains
    a persistent connection to TimesTen. Monitoring schemes (typically based
    on scripts) that open a connection each time they check TimesTen impose
    an unnecessary and undesireable loading on the system and are discouraged.
    2. Many aspects of monitoring are 'stateful'. They require periodic
    sampling of some metric maintained by TimesTen and comparing its
    value with the previous sample. This is another reason why a separate
    process with a persistent connection is desireable.
    3. A good monitoring implementation will be configurable since the values
    used for some of the chcks may depend on e.g. the TimesTen configuration
    in use or the workload being handled.
    MONITORING THE HEALTH OF A DATASTORE
    ====================================
    At the simples level, this can be achieved by performing a simple SELECT
    against one of the system tables. The recommended table to use is the
    SYS.MONITOR table. If this SELECT returns within a short time then the
    datastore can be considered basically healthy.
    If the SELECT does not return within a short time then the datastroe is
    stuck in a low level hang situation (incredibly unlikely and very serious).
    More likely, the SELECT may return an error such as 994 or 846 indicating
    that the datastore has crashed (again very unlikely, but possible).
    A slightly more sophisticated version would also include an update to a
    row in a dummy table. This would ensure that the datastore is also capable
    of performing updates. This is important since if the filesystem holding
    the trsnaction logs becomes full the datastore may start to refuse write
    operations while still allowing reads.
    Now, the SYS.MONITOR table contains many useful operational metrics. A more
    sphisticated monitoring scheme could sample some of these metrics and
    compute the delta between subsequent samples, raising an alert if the
    delta exceeds some (configurable) threshold.
    Some examples of metrics that could be handled in this way are:
    PERM_IN_USE_SIZE and PERM_IN_USE_HIGH_WATER compared to PERM_ALLOCATED_SIZE
    (to detect if datastore is in danger of becoming full).
    TEMP_IN_USE_SIZE and TEMP_IN_USE_HIGH_WATER compared to TEMP_ALLOCATED_SIZE
    (ditto for temp area).
    XACT_ROLLBACKS - excessive rollbacks are a sign of excessive database
    contention or application logic problems.
    DEADLOCKS - as for XACT_ROLLBACKS.
    LOCK_TIMEOUTS - excessive lock timeouts usually indicate high levels of
    contention and/or application logic problems.
    CMD_PREPARES & CMD_REPREPARES - it is very important for performance that
    applications use parameterised SQL statements that they prepare just once
    and then execute many times. If these metrics are continuously increasing
    then this points to bad application programming which will be hurting
    performance.
    CMD_TEMP_INDEXES - if this value is increasing then the optimiser is
    comntinually creating temporary indices to process certain queries. This
    is usually a serious performance problem and indicates a missing index.
    LOG_BUFFER_WAITS - of this value is increasing over timne this indicates
    inadequate logging capacity. Yiou may need to increase the size of the
    datastore log buffer (LogBuffSize) and log file size (LogFileSize). If that
    does not alleviate the problem you may need to change your disk layout or
    even obtain a higher performance storage subsystem.
    LOG_FS_READS - this indicates an inefficieny in 'log snoop' processing as
    performed by replication and the XLA/JMS API. To alleviate this you should
    try increasing LogBuffSize and LogFileSize.
    Checking these metrics is of course optional and not necessary for a basic
    healthy/failed decision but if you do check them then you will detect more
    subtle problems in advance and be able to take remedial action.
    MONITORING THE HEALTH OF REPLICATION
    ====================================
    This is a little more complex but is vital to achieve a robust and reliable
    system. ideally, monitorting should be implemented at both datstores, the
    active and the standby. There are many more failure modes possible for
    a replicated system than for a standalone datastore and it is not possible
    to ennumerate them all here. However the information provided here should
    be sufficient to form the basis of a robist monitoring scheme.
    Monitoring replication at the ACTIVE datastore
    1.     CALL ttDataStoreStatus() and check result set;
    If no connections with type 'replication' exists, conclude that
    replication agents are stopped, restart the agents and skip
    next steps.
    It is assumed here that the replication start policy is 'norestart'.
    An alarm about unstable replication agents should be raised
    if this is Nth restart in M seconds (N and M are configuration parameters).
    The alarm can later be cleared when the agents stayed alive K
    seconds (K is configuration parameter).
    2.     CALL ttReplicationStatus() and check result set;
    This returns a row for every replication peer for this datastore.
    If the pState is not 'start' for any peer, raise an alarm about paused or
    stopped replication and skip rest of the steps.
    It is assumed that master cannot help the fact that state is not
    'start'. An operator may have stopped/paused the replication or
    TimesTen stopped the replication because of fail threshold
    strategy. In former case the operator hopefully starts the replication
    sooner or later (of course, after that TimesTen may stop it again
    because of the fail threshold strategy). In latter case the standby
    side monitor process should recognise the fact and duplicate the data
    store with setMasterRepStart-option which sets state back to 'start'.
    If for any peer, lastMsg > MAX (MAX is a configuration parameter), raise
    an alarm for potential communication problems.
    Note that if replication is idle (nothing to replicate), or there is
    very little replication traffic, the value for lastMsg may become as
    high as 60 seconds without indicating any problem. The test logic
    should cater for this (i.e. MAX must be > 60 seconds).
    3.     CALL ttBookmark();
    Compute the holdLSN delta between the values from this call and the
    previous call and if the delta is greater than maximum allowed
    (configuration parameter), raise an alarm about standby
    that is too far behind. Continue to next step.
    Notice that maximum delta should be less than FAILTHRESHOLD * logSize.
    4.     CALL ttRepSyncSubscriberStatus(datastore, host);
    This step is only needed if you are using RETURN RECEIPT or RETURN TWOSAFE
    with the optional DISABLE RETURN feature.
    If disabled is 1, raise an alarm for disabled return service.
    Continue to next step. If RESUME RETURN policy is not enabled we could,
    of course, try to enable return service again (especially when DURABLE
    COMMIT is OFF).
    There should be no reason to reject TimesTen own mechanisms that
    control return service. Thus, no other actions for disabled return
    service.
    Monitoring replication at the STANDBY datastore
    1.     CALL ttDataStoreStatus();
    If no connections with type 'replication' exists, conclude that
    replication agents are stopped, restart the agents and skip
    next steps.
    It is assumed that replication start policy is 'norestart'.
    An alarm about unstable replication agents should be raised
    if this is Nth restart in M seconds (N and M are configuration parameters).
    The alarm can later be cleared when the agents stayed alive K
    seconds (K is configuration parameter).
    2.     Call SQLGetInfo(...,TT_REPLICATION_INVALID,...);
    If the status is 1, this indicates that the active store has marked this store
    as failed due to it being too far out of sync due to log FAILTHRESHOLD.
    Start recovery actions by destroying the datastore and recreating via a
    'duplicate' operation from the active.
    3.     Check 'timerecv' value for relevant row in TTREP.REPPEERS
    If (timerecv - previous timerecv) > MAX (MAX is a configuration parameter),
    raise an alarm for potential communication problems.
    You can determine the correct row in TTREP.REPPEERS by first getting the
    correct TT_STORE_ID value from TTREP.TTSTORES based on the values in
    HOST_NAME and TT_STORE_NAME (you want the id corresponding to the active
    store) and then using that to query TTREP.REPPEERS (you can use a join if
    you like).
    The recovery actions that should be taken in the event of a problem with
    replication depend on several factors:
    1. The application requirements
    2. The type of replication configuration
    3. The replication mode (asynchronous, return receipt or return twosafe)
    that is in use
    Consult the Timesten replication guide for information on detailed recovery
    procedures for each combination.
    ================================ END ==================================

    The information in the forum article is the abridged text of a whitepaper I wrote recommending best practice for building a monitoring infrastructure for TimesTen. i.e. you write an 'application' in C, C++ or Java that performs these monitoring activities and run it continually in production against your datastores. Various aspects of the behaviour of the application could be controlled by configurable parameters; these are not TimesTen parameters but parameters defined and used by the monitoring application.
    In the specific case you mentioned, the 'lastMsg' value returned by ttReplicationStatus is the number of seconds since the last message was received from that peer. The monitoring application would compare this against some meaningful threshold (maybe 30 seconds) and if lastMsg is > that value, raise an alarm. To allow flexibility, the value compared against )MAX) should be configurable.
    Does that make sense?
    Chris

  • It ALL works (mostly)!!! CPU Temp Monitor??

    Just finished assembling my new system and loading it up this weekend, and amazingly, it works. Even with CL3 ram it runs much faster than a P4 1.8A on SiS 645/DDR333 board I had. I am amazed at how big a difference there is in the way XP Pro loads and retrieves data and how smooth it sets up. I did not have to load ANY drivers! A huge step forward from 98SE.
      The only issue appears to be that the temperature monitor is out to lunch (So was my last board the SiS645 one, it did the exact same thing) for both CPU and Case. I installed a seperate case system to monitor temp and it gives me 22 deg C after I rearranged the airflow from the fans. I am thinking of drilling out the stock heatsink and inserting one of these temp monitors to real time monitor the CPU.
      Has anyone come up with a good way to really monitor CPU temps with this board??

    Hey,
       I loaded up MBM (after I figured out what it was and where to find it). It seems pretty good: The case reads 37 deg C (my independent sensor reads 27 deg and bios says 47) and CPU reads 47 deg (bios says 57).
       The real questions is : My -12 volts reads -6, and I have played with the settings to find the right sensor, and every sensor I select changes all the voltage readings. Is there a specific selection for readings that sets this up right?
       Also, I found a Lian-Li temp sensor with thin tape probes that is designed to be set between CPU/Heatsink to provide real time accurate monitoring for chips (theres two, so I plan on doing CPU and NB), so I will have real data instead of hoping it is right. (19.00 US). Nice little 3.5" or 5.25"  models avail in black, silver or beige.
    Nick

  • Msi fx 5700 ultra 5900xt compatibility

    Hi
    I recently bought a MSI fx5700 ultra to replace my ge force 4200 ti, However when I installed it is was a no go ran for about 10 seconds then the power switched of and the would not re start.  returned it to the shop who confirmed it was a dud then because no replacements are available loaned me a 5700 standard till they could get a new 5700 ultra.  ( the 5700 ran fine in my machine)  A few weeks went by then the shop contacted me informing me that could not get a 5700 ultra but would I be happy with a MSI 5900 xt which was satisfactory to me.  I installed the MSI 5900xt the machine started and windows xp loaded and detected the new hardware and all seamed fine until I went into a 3D game then strange things started to appear on the screen.  I re started the computer but even at the POST screen the screen was full of small vertical lines all over the screen and I could not get xp to load.  Back to the shop who again loaned me the 5700 standard which again worked fine.  and they confirmed the 5900xt was a faulty card.  
    My system is:
    P4 2.53 gig 533 front system bus
    ASUS p4pe motherboard AGP 4 only 1.5 volt
    1 gig ram
    Sound blaster live
    a good quality power supply (thermo ??? 480 watt)
    2x120 gig hard drives
    cd writer.
    My question are
    1/ As I understand it both cards are backward compatible with agp 4 / 1.5 volt. is this true or an I damaging the cards by installing them into my asus p4pe motherboard?
    2/ Is it common to fine a faulty batch of cards? I have been building my own computers for about 6 years with no hardware problems until the 5700 ultra drama.
    3/ Can any one suggest any thing else I may be doing wrong?
    PS all my system is standard eg not over clocked etc.
    Thanks in advance for any help anyone may be able to give
    Bob

    Thanks for the reply
    the power supply is a Thermal Take silent pure power
    Specifications:
    Designed for AMD K7 and Intel ATX +12V 1.1 and ATX 2.03 version (Fully Support Pentium 4)
    Serial ATA (Advanced Technology Attachment)
    Active PFC (Power Factor Correction)
    Peak Output: 550W
    Two adjustable manual fan speed controls for use in the front and rear side of the case. (From 1300 RPM at 25°C~ 4800 RPM at 90°C).
    Temperature Automatic Fan Speed Control
    Noise: 17 dBA at 1300 RPM, 45 dB at 4800 RPM
    Dual fans power supply
    Xaser badge on side panel w/ black / silver color printing
    Specifications:
    Type: ATX
    Maximum Power: 480W
    PFC: Active
    Power Good Signal: 100-500ms
    Hold-up Time: >16ms at Full Load
    Efficiency: >65%
    Over Voltage Protection: +5V trip pointOverload Protection: Not specified
    Input Voltage: 100 - 240 Vrms
    Input Frequency Range: 47-63 Hz
    Input Current: 8A
    Output: +3.3V@30A;+5V@40A;[email protected];+12V@18A;[email protected];+5VSB@2A
    MTBF: Not specified
    Approvals: Not specified

  • GF 5700 Ultra, problems with KG7 Motherboard

    Hi,
    My system specs are:
    Athlon 1400 (t-bird, 133 bus)
    KG7-lite motherboard
    512Mb corsair memory (333, running at 266)
    MSI geforce 5700 ultra
    sound blaster live value
    120 gig west dig, 80 gig western dig
    I have had a fair few problems with this card, firstly it took me several hours to get it working.  When i first put it in the screen was pretty distorted.  I tried to install the latest nvidia drivers but they caused the screen to turn blank (signal but black screen) when windows came to the log on screen.
    I reset my bios settings for my motherboard and got windows to boot although it was ni 4-bit colour mode. Eventually I was able to get the correct drivers installed and the card seems to be working OK.
    When i turn certian settings on like "fast write" it causes the screen to blank out like previously mentioned.
    Now its installed im not really satisfied with the quality but im putting this down to my fairly low spec CPU and motherboard which i hope to upgrade in the new year.
    [edit] Morrowind, which is the only game i have tried, is now unplayable and i am unsure why.  The graphics right from the first screen are distorted. [/edit]
    anyone else had any of these problems and know if there will be any fixes for this?
    cheers,
    Seb

    Seb,
    The picture was exactly what I was looking for. You have everything bunched up on IRQ5. Your system does not have a chance of running correctly in that configuration.
    your motherboard is too old to support APIC so you only get IRQs 0-15. To free up some IRQs, disable COM1, Com2, and Parallel Port if you are not using them.
    You should not use PCI Slot 1 because it shares the IRQ with AGP Slot. You should not use PCI Slot 4 because it shares with the USB Controller. You should not use PCI Slot 5 because it shares with the Highpoint IDE Controller. The rest of the PCI Slots should be fine.
    Make sure you load the latest Motherboard Drivers too.
    Take Care,
    Richard

  • Need hardware monitor for MSI 8851

     :O
    I need some help with locating a hardware monitor for the MSI geforce3 Ti200 (8851).  Does anyone know why this graphics card doesn't come with the hardware monitor or the virtual desktop?  If you know where to find such a program, well, you know what to do.
    jtb

    Quote
    Originally posted by Deathstalker
    jtb,
    The program comes with the CD drivers
    There should be 3 ways to do it
    1. Use the MSI CD autorun to install 3D Turbo Experience
    2  Manually install the 3D turbo exp from MSI CD path
    Utility/MSI/3dturbo/3dturbo.exe
    3. download 3D turbo exp from MSI website:
    3D! Turbo Experience
    Take Care,
    Richard
    Richard -
    I tried both the CD version of this and the website version and got the same problem - everything works except the Fan Speed, Temperature, and Voltage sections.  They do not respond.  They do work on an MX440 card we installed in a PC at the store I work at - why don't they work for this card?
    The card is the MS-8871 Geforce4 Ti4400-TD.  Is there a way to make this work, or if not, is there another program out there that will give me the fan speed, temps, and voltage?  I would like to know this information.
    Thanks!
    Scott Wasilewski

  • Preferred cpu temp monitor softy?

    what is the good cpu temp monitoring softy for 875pneo? i mean the accurate one. I've used aida and core center but yield different result. dont know which one to use... thnx!

    I have been using motherboard monitor for years and is simply the best freeware monitor around.  It even does OSD scripts with xml coding.
    Motherboad Monitor
    G16aByT3

Maybe you are looking for