Temperature reading for K7N2 Delta ILSR

I have a 2500+ Barton (333 FSB) to work with K7N2 Delta ILSR and 2x256 MB Samsung DDRAM(400 FSB).I use MBM to read my CPU temperatures.Usually 45-47 C idle and 54-58 C under full load.I overclock CPU to 400 FSB and I get LOWER TEMPERATURES!!!!!
 I use 1:1 bios setting for CPU and DRAM speeds either 333 or 400 FSB.
 How can this by possible?

I use Speedfan which seems to follow the temp in the bios. I've heard that MBM is also accurate. As far as your temps going down on a OC that is very odd indeed.  

Similar Messages

  • AGP Setup For k7n2 delta ilsr

    I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

    Hi,
    No, leave it at 64 or 128.
    Go here for an explanation:
    http://www.rojakpot.com/default.aspx?location=7&var1=18
    Then - Click on:  "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
    Axel  

  • Need help with jumper settings for k7n2 delta ilsr

    I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
    Thanks, Ron.

    Hi,
    As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
    Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
    Axel  

  • Kingston HyperX Memory for K7N2 Delta-ILSR

    Hey will my K7N2 Delta-ILSR support the Kingston HyperX serises DDR400-512MB Ram?
    Im looking to buy 2 maybe 3 of these and really want to be sure theyll work.
    http://www.ec.kingston.com/shop/partsinfo.asp?ktcpartno=KHX3200A/256&promo=hx2shp
    I checked the supported ram list for the K7N2 Delta-ILSR  and they wernt on there so i just figured it may be out of date?
    So thanx in Advance for info!
    p.s. It will support 3x 512MB right?

    Has anyone noticed how the Hyper X went from the poor-man's Corsair to being priced equal to OCZ, and usually higher then Geil, as well as usually being very close to Corsair, if not the same? I think only Mushkin beats it out now price-wise...

  • New Modded BIOS for K7N2 Delta ILSR

    MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
    download here:

     Description: Access through interface which is on insecure interfaces list detected. Request aborted.
    Interface/Client IP address:
     Date: Wed, 18 May 2005 13:11:17 GMT
    Doesn't work for me 
    By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
    EDIT: Thanks it's working now 

  • Case Recommendation for K7N2 Delta-ILSR

    Greetings,
    I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb.  By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb.  My eyesight isn't as sharp so hooking up those one wire at a time is tediuous.  Not to mention the lack of starndards   Does anyone know if this is address on the next rev of mb's (with pcix etc).
    Thanks

    Brazos,
    I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
    If you want a good case at a cheap price, then go with the SLK3700AMB:
    If you want a good high end case, then go with the Sonata:
    If weight is an issue, then go with the Super Lanboy:
    Take Care,
    Richard

  • Warranty Length for K7N2 Delta-ILSR

    What is the mfg's warranty length on the K7N2 Delta-ILSR?
    I filled out the online support form earlier today but no response as of yet, and me being the impatient rascal I am, I didn't want to wonder all weekend. I bought it October, 2003 and the floppy drive controller seems to have gone out.
    Thanks!
    HH

    Thank you, Glenn!
    Looks like mine is 2 yrs. & 4 months old. Kind of stinks that I lost 5 months on the warranty by going by the mfg. date instead of date of purchase. Its not worth the hassle & would even cost more to RMA it for the controller. Ahh, but this is IT, the "World of Workarounds". I'll live!
    Thanks for your time, Glenn! 
    HH

  • Anyone help - need I/O plate for K7N2 Delta ILSR??

    I'm based in the UK but will pay P&P worldwide........
    cheers
    D.

    Good luck!
    http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
    Edit: If applicable:
    http://www.mycableshop.com/sku/ATXBACKPLATE.htm

  • Linux for K7N2 Delta-ILSR

    Hello,
    Does anyone know of with Linux distro is compatible with the K7N2 Delta Series?
    Sincerely, Deft

    Knoppix worked too, even my TvTuner worked.
    Not that I would recommend Knoppix as a solution, I was just playing.
    There is a lot more support for the nvidia kit now.

  • Best agp card for k7n2 delta ilsr

    Hi again folks
    I'm thinking of upgrading my graphics card as although this card has never let me down its the oldest component in my box, I would like to get something in the sub £100 range, I dont do games but may wish to in future, mainly it would be for photo apps/running-backup-watching dvd's etc. any info would be greatly appreciated tia Hazzo

    I notice your talking in £'s so I assume your located in the UK. 
    Have a look around overclockers.co.uk
    For a sub £100 I noticed a good offer:
    HIS ATI Radeon 9800 Pro - £82
    Also, the 6600GT here is only £103.24 (£106 inc delivery), altough only 4 left in stock so buy now if you want one 

  • Replacement Chipset/Heatsink Fan (northbridge? for k7n2 delta-ilsr)

       < i need a replacement heatsink and fan for this fan.  that will fit!          Reason: I want a new one that is quiter, and the original fan in it broke.  I also need to be able to buy these part(s) online.

    Me too. You can get them in copper or aluminium. I have the latter, and for more than year now it's been doing a fine job with minimum noise.
    Check it out here:
    http://www.pcabusers.com/reviews/iceberg/p1.html

  • Best Cooler For XP 3000+ on K7N2-Delta ILSR?

    As the title suggests I am looking for a good, high performance Heatsink and Fan for my current XP 3000+ system. I have a K7N2 Delta ILSR mobo. Three Heatsinks I have been looking at are:
    Thermaltake Volcano 12 Extreme
    Thermalright SLK-900A with a Vantec Tornado 92mm fan
    Thermaltake SilentTower - (I think this one requires holes in the Mobo which the K7N2 Delta ILSR doesn't have :( Please correct me if I am wrong).
    I am looking for a high-performance heatsink at an affordable price (max £50) with which I can do some overclocking. Currently I have one of the Zalman ones ( I think it is a CNPS6000-CU) which is insufficient (load temps 66 C).  Help would be much appreciated. Thanks in advance.

    Yeah, i'm looking for a good price vs performance vs noise solution really. Both the Volcano and the Vantec Tornado are really loud, but they seem to perform quite well.

  • Dont find any connection for PFC on K7N2 Delta ILSR

    Hi !
    Just bought a MSI Motherboard K7N2 Delta ILSR
    Looking for the connector pin for my PFC  ( Power fan Control)
    I can only find two fanconnectors on the board
    CPU and System
    SORRY if this question has been asked before
    searched the Forum but did not find anything

    I just installed this same board. I only found 2 also, so I suppose that is all there is.  If you are trying to set the system up so you can monitor the power supply temps and fan, here is what I did.
    The chipset fan is a 12V fan, so unplug it from the motherboard and power it by using an adapter so you can run it off one of the Molex leads.  I do not know if they make these because I fabricated the wiring myself.  You will not be able to monitor the chipset temps though.
    To fab the connector, I just used the wiring from an old system fan and soldered two small pins (about  one-quarter of an inch long), covered each lead with heat shrink and plugged them in via a standard Molex connector.  Make sure that you do not leave any of the pin exposed, ie: (the heat shrink should push up to the plastic of the chipset fan connector)..  I finished it by covering the new connector with heat shrink to make sure it didnot come apart.
    Now you can use the northbridge fan control for the pfc.  This has worked good for me, and was $30 cheaper than a fan controller unit

  • MSI K7N2 Delta-ILSR Dead? Help!

    Hey all,
    Well, the other day I was on my computer playing a game when my mobo fan started making an odd noise (as if switching rpm), so I took off the side of my case and took a look inside. Everything seemed to be functioning properly, then I switched my cpu fan speed via the pci slot speed control. As I switched from High-Medium-Low, I noticed that the fan actually slowed to the point where I could see the blades spinning, at least for a second or so. I found that rather odd, seeing as how I've never seen a fan (especially a cpu fan) slow to the point that I could see the blades spin. Anyway, a couple of hours later, I shut down and went to sleep.
    The next day I had my comp on for about maybe 30mins to an hour or so when suddenly I heard an alarm from the computer speaker, so I was like, ":censored:?" since I had never heard it before. It was evidently the temperature warning, which I had set to 70C. So I shut down within 15 seconds and opened up the side of my case.
    I noticed that the cpu fan wasn't moving at all (usually I'd open the case in time to see the spin-down). So I turned the computer back on and the fan didn't budge, so I immediately powered down, assuming that the CPU Fan had died. Later on, I hooked the fan itself up to a free power cord in my sister's computer and booted up, along with the speed controller, flipping from medium to high to low without any problems.
    I then did screwed the fan back to the heatsink in my comp and booted up. I went into the bios an noticed that the rpm was 8k, which is way too high for my fan (normally 5k). So i began switching from high, medium, to low once again, then I saw that the rpm reader in the bios went to 0. So I looked back in the side of my case and saw that the cpu fan was once again dead. At this point I concluded that it was the fan and was about to order the Volcano 12.
    A day later I placed the fan inside my sister's computer on a free cord, yet again, and yet again, it worked fine.
    I once again put it in my computer to test and this time it worked fine, even while switching between speeds. Unfortunately, I then noticed that the mobo fan was not moving, then began to move.
    Well, I'm guessing now that it's simply the motherboard that has a short, since both the motherboard fan as well as the cpu fan have randomly been dying the past few days. The motherboard fan; however, has switched rpm many times in the past from 5k to 3k.
    It could also be a PSU problem, but I have Antec 400watt psu and it's been working fine for the past 2 years, so I doubt it. I've had the motherboard for a little over a year. I upgraded my cpu from 2200+ to 3000+ in July. That's also when I bought the cpu fan. The motherboard fan began fluctuating in rpm noticeably back in April or May of this year.
    Yesterday, I used the computer again and had it on for about 2 hours or so and I had speedfan monitoring the temps and the rpm. The temps stayed relatively stable: 48 cpu, 44 mobo.
    But alas, the RPMs were totally [blame me for the swear filter] up. At one point, both the mobo and cpu fan speeds were reading 0, even though both continued to spin within the case and the temps remained the same. Then after 30mins or so, they cpu fan began reading again at 40,000-42,000rpm, which is obviously incorrect, seeing as the fan is rated for around 5k. I got/get the same readings in the bios, both fans reading at 0rpm as they continue to physically spin.
    Also, during a number of times that I've started up the comp within the past few days, the motherboard northbridge fan wasn't spinning at all and didn't begin to until a few minutes into my windows session.
    Also, I took out the NB fan and noticed a slight crack in the back of it.
    I was considering simply just buying the Volcano 12 and the MSI K7N2 Delta2 Platinum rather than RMAing the mobo. Then perhaps an Antec 550W psu, if necessary.
    Any ideas what I should replace and in which order? And has anybody else encountered any similar problems with this mobo (at least with the mobo rpm, which has been a prob for about 6months on and off)?
    I bought the mobo along with a 2200+ in July of 2003. I upgraded the ram from 256 to 512 in April 2004 (which is around the time I started hearing rpm probs with the mobo fan) and I upgraded the cpu in July of 2004
    Many Thanks!  
    My Specs are as follows:
    Windows XP Professional SP1
    Antec SX1040B2 File Server Case
    400watt Antec PSU
    MSI K7N2 Delta-ILSR
    AMD Athlon XP 3000+ (2.17GHz)
    Thermaltake TR2 M2 HSF
    Kingston 256MB of PC2700 DDR-333MHz RAM
    Generic 256MB of PC2700 DDR-333MHz RAM
    ATI All-In-Wonder 9800 Pro
    Sound Blaster Audigy 2ZS Platinum
    Pioneer 10x DVD Drive
    Sony 8x Double Layer DVD-+RW
    Western Digital 120.0GB 7200RPM HD ATA/100
    Western Digital 120.0GB 7200RPM HD ATA/100
    nForce Ethernet Adapter w/Cable line
    Logitech MX500 Optical Mouse
    Logitech Elite Keyboard
    19" Envision Monitor EN985e
    Logitech Z-680 5.1 Speakers

    Could be a fluctuating PSU that's breaking down power to the MB. You have a whole lot of components dragging that PSU down. With what you have in your rig I would run either an Antec or Enermax 550W. Best way to be sure is to borrow a PSU or buy one from a store with a good return policy so that you can return it if indeed it turns out to be the MB. If I don't have your board here on my bench to test the only thing I can suggest to you is to swap out components unfortunately.

  • K7N2 Delta ILSR and XP2500+ - strange overclocking problem

    Relevant configuration data:
    - K7N2 Delta ILSR (with 7.6 BIOS version)
    - Barton 2500+ (AQXEA)
    - Arctic Silver 3 thermal compound
    - GlobalWin CAK 38 (7000 rpm DELTA, all copper)
    - 2x512 MB Corsair XMS cmx512 3200c2 (it should run 6-3-3-2 at 200MHz on AMD systems according to older documents, and on 6-3-3-2.5 at 200MHz  on AMD systems according to newer documents)
    - PSU Enermax EG465P-VE (430W)
    - Gigabyte ATI Radeon 9800Pro 128MB
    - Battlefield 1942 game  
    I have 2 seperate problems:
    1. When I try to set my proc on 13x166 (Barton XP3000+) BIOS won't recognise that settings and it gives me real-clock rate of 833MHz (and no name, just "Athlon XP"). Just a note, when I set proc to be XP2600 or XP2800, everything is great in BIOS and in real conditions (Windows, Battlefield). I had 7.4 version of BIOS and I tried with new 7.6 version and nothing has changed (as I suspected). Can someone help me about this ?
    2. Second problem is a bit more serious.
    I'm having problems setting my proc to work with 100% stability on 200MHz FSB speed.
    This is what's going on:
    - Behaviour in Windows is pretty much good (no random restarts).
    - Sometimes (on rare occasions) blues screen appears when I'm in windows or some program. Last time when it appeared it said something about "memory managment". I tried to lower memory settings but nothing seemed to be better.
    - If I try to freshly install windows on 200 MHz FSB in 98% of the cases installation will be abrupted (blue screen or resets) or it won't even start to install.
    - What's bothering me the most is this: Battlefield 1942 is crashing on regular basis. Sometimes it can hold for 5 minutes, sometimes 20 minutes, sometimes half an hour. But on certain moment, puff, and I'm out in Windows. Not a computer restart, just it throws me on desktop.
    I've been checking the temperature on regular basis when I'm playing. It is always low.
    I've tried to raise core voltage all the way to 1.8v, but same thing happens.
    I've tried to lower memory settings, but I get same BF crashing.
    I don't know what else to do or what other component to acuse for instability.  
    Can somebody please help me ?
    Thank you in advance !

    Quote
    Originally posted by ellswt
    On the newer 2500+'s the multiplier is locked, this could be your problem
    Nope, because I am changing multiplyers without probs. The only multiplyer that doesn't work is 13x.
    Quote
    ...loosen up your memory timings to add stability, and give it a try again at the 200 mhz fsb without changing the multiplier.
    I drove the memory according to the Corsair's specs, and I drove it on lower settings also. No change.
    Quote
    also you may wish to go up to 2.7 volts for your ram, and 1.7 volts on your processor to add stability, remember sometimes you have to go up gradually a step or two at a time and keep it there for a day or two before you reach your top OC.
    I might try upping ram voltage but that doesn't sound good, because it IS DDR 400 memory (an excellent one too !).
    It's not like I'm trying to drive it over 200MHz. 200MHz is this memory's normal frequency.
     Quote
    Newest video driver from ATI may help with the stability on your gaming.
    Already have newest drivers.
    Anyway, thanks for the tips !  

Maybe you are looking for

  • Regarding File Adapter

    Hi All,    How can I specify the source Directory in Sender File Adapter. I have given it as <hostname>\<directory>. I am getting the error <hostname>\<directory> does not exist in adapter status. The directory is shared and has all permissions. Help

  • My Dock appears to have crashed and doesn't automatically re-launch...

    My Dock appears to have crashed and whereas I would normally expect it to re-launch itself and re-appear, it's not doing anything... It's just not there. Moving my mouse to the bottom of the screen does nothing. Attempting to toggle the "automaticall

  • Where is the alphabet in Address Book

    In Address Book under SL, there was an alphabet. Clicking on one letter took you to all the contacts whose names started with that letter. I don't see the alphabet in Lion. Is it hiding?

  • Server Admin won't connect

    Trying to connect to a X.5 server in server admin, but nothing happens. System.log shows: Jan 26 10:43:30 server servermgrd92: servermgrd: readFile File /Library/Preferences/SystemConfiguration/com.apple.smb.server.plist is not a valid plist Jan 26 1

  • I think my book has an error can you varify? (To do with GC)

    class Beta{} class Alpha{     static Beta b1;     Beta b2; public class Tester{     public static void Main(String[] args{         Beta b1 = new Beta();         Beta b2 = new Beta();         Alpha a1 = new Alpha();         Alpha a2 = new Alpha();