Terminology Legacy / MQC FRTS???
In case of FRTS when we apply the shaping parameters, for the specific traffic-class and this class is called under the #map-class frame-relay _______ .
What is the terminology used for this tech, it comes under legacy FRTS/MQC-based FRTS??
Sample config:
class-map TEST
match protocol http
policy-map TEST
class TEST
class class-default
shape average 1024000
shape adaptive 512000
int se1/0
service-policy out TEST
class-map TEST
match protocol http
policy-map TEST
class TEST
class class-default
shape average 1024000
shape adaptive 512000
map-class frame TEST1
service-policy output TEST
int se0/1
frame-realy interface-dlci 402
class TEST1
what is the terminology used for them, since both are achieving the same?
Thanks,
Dara
Hi,
The router says is terming the second one as GTS.
class-map match-all BGP
match protocol HTTP
policy-map SHAPE
class HTTP
class class-default
shape average 1000000
shape adaptive 512000
R2(config-if)#do sh run int se 2/0
Building configuration...
Current configuration : 546 bytes
interface Serial2/0
description FRSW
ip address 10.10.24.2 255.255.255.0
encapsulation frame-relay
serial restart-delay 0
no dce-terminal-timing-enable
no clns route-cache
frame-relay class FRTS
frame-relay map ip 10.10.24.4 204 broadcast
no frame-relay inverse-arp
end
R2(config-if)#frame traffic-shaping
Generic traffic shaping commands must be removed before enabling frame-relay
traffic shaping.
AS you can see the interface level frame-relay traffic-shaping isn't accepted when we configure this.
Similar Messages
-
Hi All. I am currently at the later stage of provisioning a new CCR Exchange 2007 migration (to
virtualise old Exchange 2007 hardware) for 5,000 users & have a quick question.
I have created around 15 newly named storage groups, & have named 1 new DB per group, with the same name (let's say New-DB-1), residing within them. The problem I have, is the old legacy DB's have different names (let's say Old-DB-1) & I need
to import them into the new storage groups, to match the new names. So far I can import/export between old & new OK if both old & new DB names\folders etc. names marry up perfectly, but are unable to if there not the same. Does anyone have any thoughts
on how best to tackle this, as this is one of the final hurdles stopping the migration? Many Thanks, JohnHi All
Many Thanks for the feedback.
The terminology 'migrate' was used based around the fact I will be decommissioning the old 2007 physical environment. This is after moving all DB's over to the new newly created Virtual environment that will host all roles.
The solution I ended up using yesterday, was the following:
1) Dismounted the relevant named DB (NEWDB) in the new environment.
2) I then ticked the 'This database can be overwritten by a restore option' box.
3) Copied over the old named DB (OLDDB) to the same location, & overwrote using the new name (NEWDB).
4) Re-mounted the (NEWDB).
5) Ran the following 2 PowerShell commands:
Get-mailbox –database OLDDB | move-mailbox –targetdatabase NEWDB -configurationonly:$true
Get-MailboxDatabase NEWDB | ResetSearchIndex.ps1 -force
6) Checked to make sure the clients were working ok, in the now the new (NEWDB) environment.
Rich: Many thanks for your PS script, which I will test with future DB moves & provide feedback
J
John. -
Which legacy systems are used for what purpose?
Hi gurus,
I tried looking in this forums, but couldnt gather much information on which legacy systems are used and for what purpose? <b>can any body send me a link that can help me understand when and where, which systems are used for what purpose..</b> I have a general understanding of Legacy systems so i am not looking for terminology explanation, i would appreciate any thing that is related to business and explains the purpose.
thanks,
kishore karnatiHi,
Term legacy system means tailor made system by group of software developer or any branded software which deals with the group requirement like tally we user for finance.
Legacy system can be based on any technology like visual basis as front end and oracle as back end or Developer 2k as front end and oracle as back end. For report most of the legacy system we have seen uses crystal report.
You can develop and implement based on the requirement from the user though you need to define some specify process to keep the system streamline which is in your hands.
Concept like devlopment/quality/production we don't have that verys strict concept.
More and more they are not intergrated each other functionally mean lets say inventory has come to the godown then your vendor outstanding should increase in finance which does not happens you need to key in the seperate value for it.
Hope this helps!!! -
Requesting legacy BIOS firmware for N750TI-2GD5TLP
This may be different from most of the UEFI requests. I have an older computer (supermicro X7QCE) that requires legacy BIOS support (or hybrid bios support) and also requires the low profile version of the card or I would have gotten the version with a switch between the two.
SN: 602-V809-319SD1501091120
As the motherboard shows no signs of recognizing the card, I can't easily retrieve the current bios version with my computer. If it is absolutely needed for a downgrade to a legacy BIOS, I can use a friend's computer. I thought I 'd check here first.
There's no hardware problem with the PCIe slot as I'm using a zotac gt 740 right now, and no power restriction problems.
I don't know the terminology that well as far as GOP or vBIOS, so sorry if Im using the terms incorrectly.Quote
Actually, NM, I found the answer in another thread. The switch explicitly switches between EFI mode and legacy BIOS mode.
These are not just modes. The switch allows to use the card with a plain legacy vbios or a UEFI/GOP (hybrid) vbios.
Quote
As this is the case, I can come to no conclusion other than there is a problem in the EFI/legacy mode handoff in the vbios for essentially every other version of the gtx750ti.
Like already said UEFI or legacy is not the only problem that can stop the card from working in an older computer but the support for later cards in general.
Quote from: flobelix on 22-May-15, 17:46:07
We don't know what "Supermicro" computer you have and what it works with since we are not Supermicro support. Legacy and UEFI mode or GOP compliance is not the only things that determine if a card runs in your machine. Newer cards must work at all on that older machine what is not guaranteed on oem machines that are very rarely updated. With latest gen vgas that is surely a problem and has nothing to do with the vga's vbios. Only Supermicro can tell you if current generation vgas are supported.
Quote
I guess if I want to get this card to work and not just return it, I'll have to hack the firmware. Dont suppose there's any tools for making that any easier?
Get used to the fact that the problem is not the card or it's vbios but your pc's oem mainboard and it's lacking support for newer cards. Else it would at least work with card switched to the legacy vbios. -
Migrate all Open Sales Orders From Legacy System (SAP) To SAP System using
Hi Experts,
I've to Migrate all Open Sales Orders From Legacy System (SAP) To SAP System using Business Objects with a new SALES ORDER DOCUMENT NUMBER referencing the older one.
I'll get all the required data with field in an excel file.
Does any standard transaction exist for it ? Or how to go ahead with it ?
Thanks and regards,
Jyoti ShankarHi
If you are checking for CREATE option then Sales Doc Type
For more Info goto SWO1 transaction -> BUS2032 --> DIsplay --> Execute --> There SELECT the method which you want to perform... There you can fine the MANDATORY parameters also....
Or in DISPLAY mode PLACE Cursor on the Required Method and CLick the PARAMETERS button on toolbar...
That will show the MANDATORY parameters...
Reward if helpful....
Message was edited by:
Enter the Dragon -
Uploading data from a view in legacy system to SAP
Hi,
I am developing a custom table in sap. The data in this table will be loaded from a view which exists in the clients legacy system (Oracle db).There will be no middleware for the data transfer.
How can this be done in SAP? Can anybody provide a detailed procedure to do this?
Thanks in advance !!!!Hi
Is the Legacy system capable of calling 'BAPI' or 'RFC'.
If yes, than you can create a RFC function module and with in the function module, you can write code to populate values to ZTABLE.
When the Legacy system calls the RFC with values, your Ztable will be updated
Regards
Madhan -
Steps to prepare and upload legacy master data excel files into SAP?
Hi abap experts,
We have brand new installed ECC system somehow configured but with no master or transaction data loaded .It is new empty system....We also have some legacy data in excel files...We want to start loading some data into the SAP sandbox step by step and to see how they work...test some transactions see if the loaded data are good etc initial tests.
Few questions here are raised:
-Can someone tell me what is the process of loading this data into SAP system?
-Should this excel file must me reworked prepared somehow(fields, columns etc) in order to be ready for upload to SAP??
-Users asked me how to prepared their legacy excel files so they can be ready in SAP format for upload.?Is this an abaper job or it is a functional guy job?
-Or should the excel files be converted to .txt files and then imported to SAP?Does it really make some difference if files are in excel or .txt format?
-Should the Abaper determine the structure of those excel file(to be ready for upload ) and if yes, what are the technical rules here ?
-What tools should be used for this initial data loads? CATT , Lsmw , batch input or something else?
-At which point we should test the data?I guess after the initial load?
-What tools are used in all steps before...
-If someone can provide me with step by step scenario or guide of loading some kind of initial master data - from .xls file alignment to the real upload - this will be great..
You can email me some upload guide or some excel/txt file examples and screenshots documents to excersize....
Your help is appreciated it.!
Jonhi,
excel sheet uploading:
http://www.sap-img.com/abap/upload-direct-excel.htm
http://www.sap-img.com/abap/excel_upload_alternative-kcd-excel-ole-to-int-convert.htm
http://www.sapdevelopment.co.uk/file/file_upexcel.htm
http://www.sapdevelopment.co.uk/ms/mshome.htm -
How to get Acknowledgement from legacy system in an Asynchronous scenario?
Hello Experts,
My current scenario is to send an invoice from ECC --> ABAP proxy --> PI --> webservice --> Legacy system & I need acknowledgement back to ECC system from legacy system. How SAP XI acknowledgements work in asynchronous scenarios?
Please guide.
Thanks & Regards,
Nidhi KukrejaHi nidhi,
please check following link
http://help.sap.com/saphelp_nw04/helpdata/EN/44/932e8896b610bbe10000000a422035/frameset.htm
Also check this one.
http://help.sap.com/saphelp_nw04/helpdata/EN/f4/8620c6b58c422c960c53f3ed71b432/frameset.htm
hope this helps..
- Deepak. -
Unable to collect Product Return History using legacy collection
Hi,
I am facing issue in collecting product return history using legacy collection, File Upload (User File Upload) & Loader Worker erroring out as below. As I observe, its inserting space after .ctl, .dis & .bad file path.
Can some one guide me how to reslove below issue.
Loader Worker
Argument 1 (CTRL_FILE) = /u02/oracle/xxxxx/inst/apps/rights_apps/logs/appl/conc/out/5913849MSD_DEM_RETURN_HISTORY .ctl
Argument 2 (DATA_FILE) = /u02/oracle/xxxxx/inst/apps/rights_apps/logs/appl/conc/out/5913849PrdRetHist.dat
Argument 3 (DISCARD_FILE) = /u02/oracle/xxxxx/inst/apps/rights_apps/logs/appl/conc/out/5913849MSD_DEM_RETURN_HISTORY .dis
Argument 4 (BAD_FILE) = /u02/oracle/xxxxx/inst/apps/rights_apps/logs/appl/conc/out/5913849MSD_DEM_RETURN_HISTORY .bad
Argument 5 (LOG_FILE) =
Argument 6 (NUM_OF_ERRORS) = 1000000
===================================================================
plan_id:0 plan_type:0 planning_engine_type:1
Creating dummy log file ...
Parent Program Name: MSCLOADS
This is NOT as part of a Plan run.
NLS_LANG original American_America.AL32UTF8 alt American_America.UTF8
LRM-00112: multiple values not allowed for parameter 'control'
SQL*Loader: Release 10.1.0.5.0 - Production on Tue Mar 11 19:58:20 2014
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL*Loader-100: Syntax error on command-line
Program exited with status 1
APP-FND-01630: Cannot open file /u02/oracle/xxxxx/inst/apps/rights_apps/appltmp/OFq98wrx.t for reading
Cause: USDINS encountered an error when attempting to open file /u02/oracle/xxxxx/inst/apps/rights_apps/appltmp/OFq98wrx.t for reading.
Action: Verify that the filename is correct and that the environment variables controlling that filename are correct.
Action: If the file is opened in read mode, check that the file exists. Check that you have privileges to read the file in the file directory. Contact your system administrator to obtain read privileges.
Action: If the file is opened in write or append mode, check that you have privileges to create and write files in the file directory. Contact your system administrator to obtain create and write privileges.
***** End Of Program - No title available *****
File Upload (User File Upload)
Tue Mar 11 19:57:52 RET 2014: Profile 'MRP_DEBUG' Value : N
Tue Mar 11 19:57:52 RET 2014: ===============================================================
Tue Mar 11 19:57:52 RET 2014: fileLoaderInit: paramName = pLOAD_ID; paramValue=41563
Tue Mar 11 19:57:52 RET 2014: ===============================================================
Tue Mar 11 19:57:52 RET 2014: The control file Path /u02/oracle/xxx/apps/apps_st/appl/msc/12.0.0/patch/115/import/MSD_DEM_RETURN_HISTORY .ctl does not exist. Please contact your System Administrator
Regards,
MLHi,
Login to unix server and I believe the control file is placed in a custom top say $MSC_TOP in your environment.
just try to rename the ctl file without the MSD_DEM_RETURN_HISTORY<space>.ctl
And try to upload the file once again.
Hope this helps...!!! -
What is the diff b/w flat file and legacy system?
Hi everyone,
when v say v r working on scenario FILE to FILE? which format of file r v usually working on? and what is the diff b/w flat file and legacy system?
thanxHi,
<i>when v say v r working on scenario FILE to FILE? which format of file r v usually working on?</i>
>>>Many a times it will be a Flat file with CSV format,Tab delimited format, fixedlength fields.
<i>what is the diff b/w flat file and legacy system?</i>
>>>We can not differeniate like this..
Flat file may come from any systems, it may be live system or legacy system.
Legacy system- is something like old, or past one. If you talk about SAP , then older versions of SAP can be called as a legacy system.
So it may be a file system, or any system which is old version but it doesnot mean it is not in use,
Regards,
Moorthy -
Session Time Out capturing for legacy application running in portal
Hi Forums,
I am using portal URL iView to connect to legacy application. How to capture the session time of of that legacy application and show it in the portal. In portal I have already handled session time out which shows a javascript popup message. I want to call the same piece of code once session time out happens in the legacy application which is been accessed by portal through URL iview.
Many Thanks and Best Regards
SudhirHi Sudhir,
The handling of the session timeout should be done by the application itself not the portal. From the portal you have no way of working out what the application is doing. My suggestion to you is that you need to modify the application to handle the scenario you describe not the portal.
BRgds,
Simon -
IdM 7 and SSO for legacy applications
Dear experts,
Per SAP NetWeaver 7 documentation new approach allows SSO for any legacy applications without a need for a 3rd party IdM solution.
Could someone explain how this is handled? Does evary non-SAP application need to become aware of SAP IdM credential store and be able to interact with it, or some other - non-intrusive approach is being used?
Thanks in advance,
Eugene.Hi Eugene,
SAP NetWeaver Identity Management 7.0 handles the provisioning of users (identities) for a heterogeneous landscape. Authentication and Single Sign-On (SSO) is being handled within the SAP NetWeaver platform. So introducing SAP NetWeaver Identity Management itself does not introduce additional SSO functionality. -
Importing to Discussion Board Post from legacy source
Hi All,
Im sure im not the first to wonder or ask this question but here it goes.
We have recently moved out intranet to SharePoint 2013. We have rebuilt from the ground up using many of the out of box solutions as well as some third party apps and web parts however these is one aspect that is stumping us.
On our old intranet we use a SQL based forum/discussion board package which has
about ten years worth of posts, surveys, Q&As etc. As it is SQL based it is very easy for use to query and pull this legacy data however
we cannot find a way to import into SharePoint. We do not expect to import it all but would like to import at leas the last 12 months of submitted
data with at least basic fields like Title, description/content, tags, post date and post user. We do not mind other metadata being striped out like voting etc.
We have dug deep into the SharePoint database files to see if we can directly insert but
it is very complex and almost certainly not supported. We was also hoping for a discussion board data list view so we could bulk cut and paste. This is not ideal but would at least be a better option than manually inserting each post.
Does anybody have an idea where to start if at all possible.
MarkWon't keep me logged in,
This is a server problem. In other words, "don't adjust your dial!"
spinning balls,
All this means is that the rendering is slowed down by something in the design of the website. If it is a thread with over 500 posts, you probably will have difficulty viewing it, unless you have a high speed internet connection with low latency, enough hard disk space to cache the files, and/or view threads in tree mode. To use Tree mode, go to My Settings, and select Tree View under Topic Page View in the General SEttings.
Bad Request
Sometimes will happen if your internet service provider is behind a backbone with significant peering issues.
So how big is your hard drive?
How much free disk space is there?
Have you tried to empty the browser cache?
Does this issue happen with short threads as well as long ones?
Do you have any system modification software such as Speed Download, PthHelmet, or other browser enhancement software?
Are you sure all your software is known to be Snow Leopard compatible?
See these two pages about compatibility:
http://snowleopard.wikidot.com/
http://www.macintouch.com/specialreports/snowleopard/slcompat.html -
Unit testing legacy code - best approach?
Hi,
I've got a project full of legacy code (by this I simply mean untested) and I'm experimenting with retrofitting unit testing to it. I'm sure this entails a great many problems, but here's the first one.
We have a central class with the Singleton pattern - it's instantiated once and then fetched all over the code. It's a concrete class at the moment, not an interface. Let's call this CentralControl.
Because the code I want to test relies on the presence of this class, and yet it's too complex/heavyweight to properly instantiate in a test scenario, I need to mock it.
I guess the ideal way is to turn what's now CentralControl into an interface, and have both a real and mock implementation. The code that enforces the singleton behaviour could have a new method to instantiate the mock version rather than the real thing.
Would you do this yourself rather than alternatives like extending it, and are there any tools to help automate the process?
Thanks,
RobI guess the ideal way is to turn what's now CentralControl into an interface...I think that's the better idea, but you can mock classes as well as interfaces; e.g., EasyMock 2.2.2 and higher.
~ -
RE: Legacy Integration with PI/Open
Greg -
We are currently working on wrappering the APIs for UniVerse (aka Pick on
UNIX).
We received some help from the guys at RTD in Denver.
We tested out a C program that uses the Universe APIs and it works fine.
We will be building the Forte piece and compiling it this week.
Our first application is to inquire the UniVerse data, after that is
successful, we will move to inserting & updating.
Let us know how we can help.
Larry McCartney
[email protected]
(203)459-7959 - Trumbull
From:
[email protected][SMTP:[email protected]
om]
Sent: Monday, October 12, 1998 11:00 AM
To: [email protected]
Subject: forte-users-digest V1 #1111
forte-users-digest Monday, 12 October 1998 Volume 01 : Number
1111
In this issue:
Legacy Integration with PI/Open
is OBB32.dll available
Java Integration
Java Integration
Re: Legacy Integration with PI/Open
RE: Forms That Will Not Close
RE: Forms That Will Not Close
RE: Forms That Will Not Close
Re: AfterValueChange event trigged when it shouldn't be...
math library
From: [email protected]
Date: Mon, 12 Oct 1998 09:49:56 +1000
Subject: Legacy Integration with PI/Open
This is a bit of a long shot, but has anyone experience with integrating
Forte with PI/Open. PI/Open is a variant of PICK. We have a requirement
to read and update a PI/Open database from within our Forte application,
and we would be most interested to hear from anyone who has experience in
doing this.
We are aware of a set of APIs provided with PI/Open that are written in
"C". We could wrapper these from within Forte, however the issue is that
the APIs provided are non-shared, and Forte requires shared libraries.
Thanks in advance for any help.
Greg Barber.
The information transmitted is intended only for the person or entity to
which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination or other use of, or
taking of any action in reliance upon, this information by persons or
entities other than the intended recipient is prohibited. If you
received
this in error, please contact the sender and delete the material from any
computer.
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: "sridhar t" <[email protected]>
Date: Sun, 11 Oct 1998 22:01:36 PDT
Subject: is OBB32.dll available
hi,
am working on forte3.0.G.2. when i tried to use objectbroker library i
am unable to find the runtime objectbroker library (OBB32.dll). is this
dll available with this version. if not is there any alternative.
thanks,
sridhar,
Goldstone Softech USA
Get Your Private, Free Email at http://www.hotmail.com
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: srinivasa gopi <[email protected]>
Date: Sun, 11 Oct 1998 23:12:22 -0700 (PDT)
Subject: Java Integration
Hello,
I'm trying to integrate Forti with Java in Java mode using IIOP.I
followed the steps as explained in the Forti Web enterprise manual.I
compiled the Java files that are generated by Forti along with the
client Java file.The Java applet is getting downloaded on the client
browser(IE 4.0), but the problem is browser is giving an exception
** Java.lang.RuntimeException can't connect to service object with
the ior file name **.
My question is on every client is it necessary for ORB(Visigenic for
Java 3.2) and also the Forti Java interoperability package that is
provided by the Forti for compatability with Java or it is not
required on the clients ?
Is there any other alternative to achieve the goal as this will give
wide access to the Forti service objects through Web Browser clients.
Please mail me the solution to this problem as early as possible it is
very urgent.
Thanks in advance,
Srinivasa Gopi,
Goldstone Softech USA
DO YOU YAHOO!?
Get your free @yahoo.com address at http://mail.yahoo.com
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: srinivasa gopi <[email protected]>
Date: Sun, 11 Oct 1998 23:26:26 -0700 (PDT)
Subject: Java Integration
Hello,
I'm trying to integrate Forti with Java in Java mode using IIOP.I
followed the steps as explained in the Forti Web enterprise manual.I
compiled the Java files that are generated by Forti along with the
client Java file.The Java applet is getting downloaded on the client
browser(IE 4.0), but the problem is browser is giving an exception
** Java.lang.RuntimeException can't connect to service object with
the ior file name **.
My question is on every client is it necessary for ORB(Visigenic for
Java 3.2) and also the Forti Java interoperability package that is
provided by the Forti for compatability with Java or it is not
required on the clients ?
Is there any other alternative to achieve the goal as this will give
wide access to the Forti service objects through Web Browser clients.
Please mail me the solution to this problem as early as possible it is
very urgent.
Thanks in advance,
Srinivasa Gopi,
Goldstone Softech USA
DO YOU YAHOO!?
Get your free @yahoo.com address at http://mail.yahoo.com
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: Tim Hagemann <[email protected]>
Date: Mon, 12 Oct 1998 09:21:06 +0200
Subject: Re: Legacy Integration with PI/Open
Greg,
This is a bit of a long shot, but has anyone experience with integrating
Forte with PI/Open. PI/Open is a variant of PICK. We have arequirement
to read and update a PI/Open database from within our Forte application,
and we would be most interested to hear from anyone who has experiencein
doing this.
We are aware of a set of APIs provided with PI/Open that are written in
"C". We could wrapper these from within Forte, however the issue isthat
the APIs provided are non-shared, and Forte requires shared libraries.Would be interersting, which operating system you're using.
You could write a dll (on windows) or shared library (on unix) wrappering
the
original,statically linked "C"-Libs. This lib could be used by Forte.
Tim Hagemann
Tim Hagemann
Ascom GmbH Email: [email protected]
Charlottenburger Allee 61 Phone: +49 241 96806 273
D-52068 Aachen Fax: +49 241 96806 225
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: "Rottier, Pascal" <[email protected]>
Date: Mon, 12 Oct 1998 09:38:25 +0200
Subject: RE: Forms That Will Not Close
Exiting the event loop will not close the window! Invoking
'Close' method on the window will. Check if this method
is executed. It appears, the AfterFinalize event exits the
event loop and nothing more. Then, your applications
waits for some event from your main window, like 'Mouse-
Enter', before invoking Window.Close().
Pascal
Hi,
We seem to be having some type of deadlock problem when trying to
close
forms and am wondering if anyone else has experienced this problem.
The
phenomenon does not always occur and is not specific to any one client
machine.
I will explain the phenomenon:
1. We have an object that contains our main application startup
method.
This method then instantiates our main application window (Control)
and
invokes the Display() method using start task.
2. All other forms created by the application are created using a form
manager service object which exists on the client partition. The form
manager has a CreateForm() method which instantiates a form class of
the
specified type and invoked the form's Display() method using start
task.
3. Each form has a Close push button which when clicked invokes
Window.RequestFinalize().
Now, the problem we have is this:
The user starts the application and the main application window is
displayed. The user then selects an option from the main window and a
child form is created using the form manager service object and is
displayed. The user can continue to create more child forms by
selecting
options from the main window and all child forms are instantiated and
displayed correctly.
However, when the user attempts to close one of the forms the form
does
not close. The finalize event is triggered and the event loop is
exited,
but the form continues to be displayed and does not close. If the user
then moves the mouse pointer over the main application window, the
child
form immediately closes. Moving the mouse cursor over other child
windows (or even the desktop) does NOT do this - only when the mouse
cursor is moved over the main window does the child form close.
Does anyone have any ideas on this?
Regards,
Jace.
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive
<URL:http://pinehurst.sageit.com/listarchive/>- -
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: Jason de Cean <[email protected]>
Date: Mon, 12 Oct 1998 17:47:20 +1000
Subject: RE: Forms That Will Not Close
Hi Pascal,
The Display() method is as follows:
self.Open();
event loop
when Window.AfterFinalize do
exit;
when task.Shutdown do
exit;
end event;
self.Close();
<end>
Are you saying we should do a Window.Close() in there somewhere as well
Regards,
Jace.
On Monday, 12 October 1998 17:36, Rottier, Pascal
[SMTP:[email protected]] wrote:
Exiting the event loop will not close the window!
Invoking
'Close' method on the window will. Check if this method
is executed. It appears, the AfterFinalize event exits
the
event loop and nothing more. Then, your applications
waits for some event from your main window, like 'Mouse-
Enter', before invoking Window.Close().
Pascal
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: "Rottier, Pascal" <[email protected]>
Date: Mon, 12 Oct 1998 11:04:24 +0200
Subject: RE: Forms That Will Not Close
Jason,
No, self.Close() should close the window. This is the
method I referred to. You could place a traceline
behind self.Close() to see if it is executed. It is not
inconcievable some exception may exit the Display()
method before self.Close() is executed.
After that, maybe, some events from your main
window trigger something that causes a call like 'My-
Window.Close()', where 'MyWindow' is a subclass of
'UserWindow', so 'MyWindow' gets closed after all.
Maybe you've overridden 'Close()', so now it doesn't
work properly anymore.
Are you sure you exit the event loop after you press
the close button?? The display method is not regis-
terred for any <PushButton>.Click event, though maybe
you just didn't include the full Display method in your
mail.
Remember that an event loop will only respond to an
event if it is not currently handling an event. So, the
method behind <PushButton>.Click may call a self.
Window.RequestFinalize(), which will cause an After-
Finalize event to be posted, which will be placed in
the event queue. If this method however keeps waiting
for something, the event loop will not respond to the
AfterFinalize event, until this method is done waiting.
Pascal.
Hi Pascal,
The Display() method is as follows:
self.Open();
event loop
when Window.AfterFinalize do
exit;
when task.Shutdown do
exit;
end event;
self.Close();
<end>
Are you saying we should do a Window.Close() in there somewhere as
well
Regards,
Jace.
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: Thomas Kunst <[email protected]>
Date: Mon, 12 Oct 1998 14:28:55 +0200
Subject: Re: AfterValueChange event trigged when it shouldn't be...
Which version of Fort=E9 are you using? We had some strage problems with
GUI events in Fort=E9 3.0.F.2, which disappeared now that we use 3.0.J.1!=
Fouche, Jaco wrote:
=
Hi there,
=
I'm hoping that someone out there has experienced the following (and
knows why it is happening. ) :-)
=
I have a couple of windows on which the AfterValueChange event is
triggered on a field upon hitting the delete key.
We all know that this should only happen upon leaving the field, ie. th=e
field loosing focus. The problem is that I'm trying to recreate this in=
a simple test class, but now it won't happen. I still have the original=
windows on which it is happening, but I would like to construct
something small and simple to send to Forte.
=
Any ideas as to why this could be happening?
=- -- =
Dr. Thomas Kunst mailto:[email protected]
sd&m GmbH & Co. KG http://www.sdm.de
software design & management
Thomas-Dehler-Str. 27, 81737 Muenchen, Germany
Tel +49 89 63812-221 Fax -444
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
From: Greg Gorham <[email protected]>
Date: Mon, 12 Oct 1998 09:51:07 -0400
Subject: math library
I need direction to the source of Forte libs that handle more scientific
math. Also included is the need for more scientific print formating. I
understand, second hand, that such material is available from third
party vendors/sources.
Thanks
Greg Gorham
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
End of forte-users-digest V1 #1111
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>Greg,
This is a bit of a long shot, but has anyone experience with integrating
Forte with PI/Open. PI/Open is a variant of PICK. We have a requirement
to read and update a PI/Open database from within our Forte application,
and we would be most interested to hear from anyone who has experience in
doing this.
We are aware of a set of APIs provided with PI/Open that are written in
"C". We could wrapper these from within Forte, however the issue is that
the APIs provided are non-shared, and Forte requires shared libraries.Would be interersting, which operating system you're using.
You could write a dll (on windows) or shared library (on unix) wrappering the
original,statically linked "C"-Libs. This lib could be used by Forte.
Tim Hagemann
Tim Hagemann
Ascom GmbH Email: [email protected]
Charlottenburger Allee 61 Phone: +49 241 96806 273
D-52068 Aachen Fax: +49 241 96806 225
To unsubscribe, email '[email protected]' with
'unsubscribe forte-users' as the body of the message.
Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>
Maybe you are looking for
-
Difficulty upgrading from OSX 10.5.8 to 10.6.3
So I have been having difficulties upgrading my 2008 24 inch intel iMac with 10.5.8 to 10.6.3. I bought the retail version of snow leopard and recieved the disc yesterday. So after opening the package I inserted the disc into the drive. And theeennn.
-
Windows 8 and no flash player!!
I have windows 8 and am really struggling to find my way around it, in fact, I hate it. My biggest annoyance is being unable to view videos that friends send or post on facebook. It tells me that I need to install flash player yet when I do it says t
-
Borders and shading, Move all objects at once!
*Hi all, hope every1's good!! I hope someone can help me with this problem!, a friend has asked me to do a thank you card for him cos his hosting a dinner party for his work colleagues, now i know that pages 08 can do this because i've checked and st
-
Create Annotations with 'author' name tool property
Philip Cord has kindly sent me this code that allows to create annotations with the "Author" tool property (older versions than CS3 couldn't get this on script listener - only on the CS3 script listener). Hope it helps anyone like me that can't have
-
WM report for slow moving items
Hello, Is there any report in WM for slow moving items (or Dead stock)? Regards,