Test-CsGroupExpansion Failed

Hi All,
I ran Test-CsGroupExpansion in all my three FE servers but all failed with below error,
the server was unable to process the request due to an internal error, For more information about the error, either turn on IncludeExceptionDetailInFaults on the server in order to send the exception information back to client, or turn
on tracing as per the Microsoft .NET frame SDK documentation and inspect the server trace logs.
could you share with me if you have any solution. many appreciation. thanks
Best Regards
Thomas

Hi,
Did the other Lync Server function work normally?
Please check if Lync Services started on FE Servers. Then check if only this command “Test-CsGroupExpansion” failed or all other Lync command failed as well.
If the issue only happen for this command, please include the Verbose parameter, such as following:
Test-CsGroupExpansion -TargetFqdn "atl-cs-001.litwareinc.com" -GroupEmailAddress "[email protected]" –Verbose
If the issue happen for all Lync command,
Please make sure CMS replication update to the latest status.
Please make sure Lync Server update to the latest version and then test again.
Best Regards,
Eason Huang
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Eason Huang
TechNet Community Support

Similar Messages

Dmesg error.... Test WP failed, assume Write Enabled

Hi all....
there seems to be some kind of error going on. When I type
$dmesg | tail -3
[ 1398.681274] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled
[ 1398.683528] sd 4:0:0:0: [sdb] Asking for cache data failed
[ 1398.683542] sd 4:0:0:0: [sdb] Assuming drive cache: write through
This is repeated throughout the log files. And the funny thing is I don't have anything connected i.e. no usb drives, no secondary hdds. Also,
$df -h /dev/sdb
Filesystem Size Used Avail Use% Mounted on
/dev 493M 0 493M 0% /dev
What am I missing here?
Update:
Found a similar thread : https://bbs.archlinux.org/viewtopic.php?pid=1059099
Seems like its the card reader afterall.....
Last edited by whzee (2012-02-17 10:06:28)

Looks like the firmware update solved it.

Error message "test page failed to print" in windows 7 ultimate 32 bits

I have installed printer a hp deskjet 1515 in windows 7 ultimate 32 bits and it is successfully installed, however when I tried to test print out there showed message "test page failed to print. Would you like to view the print troubleshooter
for assistance?". I tried to clicked Yes and running the troubleshooter until completed but the result still the same showed the same message above when test print again.
Please need assistance how to solve this problem
Thanks
Sopyan

Hi Sopyan,
On current situation, please refer to following steps and check if help us to troubleshoot this issue.
1. Please check if use the correct printer driver and also check if need to update it.
2. Please check if firewall was enabled or third-party security application ran. Please temporarily disable them and monitor the result.
3. Please use another administrator account to logon and print again, then check if this issue still exist.
4. Please open Event Viewer and check if find some relevant events or errors.
If any update, please feel free to let us know.
Best regards,
Justin Gu
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Build file: [junit] Test unitTestMethod FAILED

build code:
<target name="testing">
<junit showoutput="yes">
<test name="unitTestMethod">
</test>
</junit>
</target>
When I run the unitTestMethod it is successful. When I try to run it through ant, it says:
[junit] Test unitTestMethod FAILED
What am I doing wrong here?

hi Tim
(1) It looks like the viewlet you refer to also has that message:
"[junit] Test translatorTest FAILED"
(2) You could try to change the Ant "Output Level" using the "Project Properties" dialog, on the "Ant" > "Options" panel. Maybe set it to "Debug" to get more information.
(3) The Ant documentation says that the "name" attribute for the nested element "test" should be "Name of the test class.", in the viewlet it looks like that would be "test.mypackage.translatorTest".
see http://ant.apache.org/manual/OptionalTasks/junit.html#nested
success
Jan Vervecken

Exchange 2010 MP : Some Client Access test cmdlets failed to run

Hi all,
This error is triggered in SCOM 2012 R2 about a single Exchange 2010 SP3 server :
Exchange 2010 MP : Some Client Access test cmdlets failed to run.
When I dig into the error context, I can see it's about the cmdlet "Test-CalendarConnectivity -TestType:External".
The TechNet
https://technet.microsoft.com/en-us/library/hh377605(v=exchg.140).aspx proposes to verify that the URL for the external virtual directory can be accessed by running the Test-OwaConnectivity.
OK.
But what sould I specify for the parameter -MailBoxCredential required for Test-OwaConnectivity -URL my_url -MailBoxCredential ?
Thank you.
Have a good day.
FXE

Hi,
Under Administration, run as configuration, profiles, you can check Default action account.
Local system is the account account for agents by default, you can change to use another account.
Regards,
Yan Li
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Testing Autodiscover failed

We are running Exchange 2007 on Windows 2008 and planning to move to Office 365. However, we can't do it because Exchange 2007 Autodiscover issue.
When we test it from
www.testexchangeconnectivity.com, we receive
Testing Autodiscover failed wth these details:
1. The SSL certificate failed one or more certificate validation checks.
2. Certificate name validation failed.
We don't have problem to access the OWA. When I check the certificate on OWA website, it is correct. I can login
https://autodiscover.ourdomain.com/autodiscover/autodiscover.xml. Here is the get-exchangecertificate information:
[PS] C:\Windows\system32>get-exchangecertificate | fl
AccessRules
: {System.Security.AccessControl.CryptoKeyAccessRule, System
.Security.AccessControl.CryptoKeyAccessRule, System.Securi
            ty.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {remote.ourdomain.com, www.remote.ourdomain.com}
HasPrivateKey
: True
IsSelfSigned
: False
Issuer
: SERIALNUMBER=07969287, CN=Go Daddy Secure Certification Au
                thority, OU=http://certificates.godaddy.com/repository, O=
"GoDaddy.com, Inc.", L=<st1:city w:st="on">Scottsdale</st1:city>, S=<st1:state w:st="on"><st1:place w:st="on">Arizona</st1:place></st1:state>, C=US
NotAfter
: 4/8/2019 2:47:53 PM
NotBefore
: 4/8/2009 2:47:53 PM
PublicKeySize
: 1024
RootCAType
: ThirdParty
SerialNumber
: 02BFCE2827
Services
: IMAP, POP, IIS, SMTP
Status
: Valid
Subject
: CN=remote.ourdomain.com, OU=Domain Control Validated, O=rem
ote.ourdomain.com
Thumbprint
: 9BFF2C1C6F99785A97CA19A1B50D942EE4CF3273
AccessRules
: {System.Security.AccessControl.CryptoKeyAccessRule, System
.Security.AccessControl.CryptoKeyAccessRule, System.Securi
ty.AccessControl.CryptoKeyAccessRule, System.Security.Acce
ssControl.CryptoKeyAccessRule}
CertificateDomains : {DC, DC.ourdomain.local}
HasPrivateKey
: True
IsSelfSigned
: True
Issuer
: CN=DC
NotAfter
    : 4/8/2010 2:41:04 PM
NotBefore
: 4/8/2009 2:41:04 PM
PublicKeySize
: 2048
RootCAType
: Unknown
SerialNumber
: 647A4A520EBA0582441BF33F595AE7A0
Services
: SMTP
Status
: Invalid
Subject
: CN=DC
Thumbprint
: 43780186DDBE3034DD6565E932DBF2EC94238950
How do you verify the certificate and autodiscover are setup correctly?
Bob Lin, MCSE & CNE Networking, Internet, Routing, VPN Networking, Internet, Routing, VPN Troubleshooting on http://www.ChicagoTech.net How to Install and Configure Windows, VMware, Virtualization and Cisco on http://www.HowToNetworking.com

Hi,
According to the result of get-Exchangecertificate, the name autodiscover.domain.com isn't in the certificate( the property CertificateDomains shows the names in one certificate).
Additionally, I'd like to confirm if there is any SRV record in the Exchange 2007 environment for Autodiscover connection. If there is no SRV record, we need to add the name autodisocver.domain.com in the certificate.
And if there is no inconvenience for you, I'd like to confirm the result of your ExRCA test.
Thanks,
Angela Shi
TechNet Community Support

Test-FederationTrust Failed to request delegation token

When running the Test-FederationTrust cmdlet on a CAS server running Exchange 2010 SP1 (RU5v1) I get an error saying that there was an issue getting a delegation token.
The actual output is here:
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : FederationTrustConfiguration
Type : Success
Message : FederationTrust object in ActiveDirectory is valid.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : FederationMetadata
Type : Success
Message : The federation trust contains the same certificates published by the security token service in its federat
ion metadata.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : StsCertificate
Type : Success
Message : Valid certificate referenced by property TokenIssuerCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : StsPreviousCertificate
Type : Success
Message : Valid certificate referenced by property TokenIssuerPrevCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : OrganizationCertificate
Type : Success
Message : Valid certificate referenced by property OrgPrivCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : TokenRequest
Type : Error
Message : Failed to request delegation token.
I re-ran the cmdlet with the 'verbose' parameter and got the following:
VERBOSE: [12:49:06.110 GMT] Test-FederationTrust : Beginning processing &
VERBOSE: [12:49:06.110 GMT] Test-FederationTrust : Instantiating handler with index 0 for cmdlet extension agent "Admin
Audit Log Agent".
VERBOSE: [12:49:06.110 GMT] Test-FederationTrust : Current ScopeSet is: { Recipient Read Scope: {{, }}, Recipient Write
Scopes: {{, }}, Configuration Read Scope: {{, }}, Configuration Write Scope(s): {{, }, }, Exclusive Recipient
Scope(s): {}, Exclusive Configuration Scope(s): {} }
VERBOSE: Testing Federation Trust
VERBOSE: [12:49:06.110 GMT] Test-FederationTrust : Resolved current organization: .
VERBOSE: [12:49:06.126 GMT] Test-FederationTrust : Searching objects "extest_5580e4a3ff4a4" of type "ADUser" under the
root "$null".
VERBOSE: [12:49:06.126 GMT] Test-FederationTrust : Previous operation run on global catalog server
'server.domain.net'.
VERBOSE: [12:49:06.141 GMT] Test-FederationTrust : Requesting Federation Metadata from
https://nexus.microsoftonline-p.com/FederationMetadata/2006-12/FederationMetadata.xml.
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Parsing Federation Metadata:
<fed:FederationMetadata>
<SNIPPED>
</fed:FederationMetadata>
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Retrieved Token Issuer Uri from Federation Metadata:
urn:federation:MicrosoftOnline.
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Retrieved Token Issuer Certificate from Federation Metadata:
B02FEAAC45742783AA61FC8DB7D0C5E0FF415239.
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Retrieved Token Issuer Previous Certificate from Federation
Metadata: 089D50FCF27AE9642BFCD95384FD0BB9C14427A4.
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Retrieved Token Issuer End Point from Federation Metadata:
https://login.microsoftonline.com/extSTS.srf.
VERBOSE: [12:49:06.704 GMT] Test-FederationTrust : Retrieved Web Requestor Redirect End Point from Federation Metadata:
https://login.microsoftonline.com/login.srf.
VERBOSE: [12:49:07.423 GMT] Test-FederationTrust : Failed to request delegation token. Reason: <S:Fault
xmlns:S="http://www.w3.org/2003/05/soap-envelope"><S:Code><S:Value>S:Sender</S:Value><S:Subcode><S:Value>wst:InvalidReq
uest</S:Value></S:Subcode></S:Code><S:Reason><S:Text xml:lang="en-US">Invalid
Request</S:Text></S:Reason><S:Detail><psf:error
xmlns:psf="http://schemas.microsoft.com/Passport/SoapServices/SOAPFault"><psf:value>0x80048820</psf:value><psf:internal
error><psf:code>0x80047867</psf:code><psf:text>Server received a SAML token from an unrecognized issuer.
</psf:text></psf:internalerror></psf:error></S:Detail></S:Fault>
Microsoft.Exchange.Net.WSTrust.SoapFaultException: Soap fault exception received.
at Microsoft.Exchange.Net.WSTrust.SoapClient.Invoke(IEnumerable`1 headers, XmlElement bodyContent)
at Microsoft.Exchange.Net.WSTrust.SecurityTokenService.IssueToken(DelegationTokenRequest request)
at Microsoft.Exchange.Management.SystemConfigurationTasks.TestFederationTrust.GetDelegationToken(ADUser user, Uri
target, SecurityTokenService securityTokenService)
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : FederationTrustConfiguration
Type : Success
Message : FederationTrust object in ActiveDirectory is valid.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : FederationMetadata
Type : Success
Message : The federation trust contains the same certificates published by the security token service in its federat
ion metadata.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : StsCertificate
Type : Success
Message : Valid certificate referenced by property TokenIssuerCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : StsPreviousCertificate
Type : Success
Message : Valid certificate referenced by property TokenIssuerPrevCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : OrganizationCertificate
Type : Success
Message : Valid certificate referenced by property OrgPrivCertificate in the FederationTrust object.
RunspaceId : 93c95e81-7679-4937-8c78-dc29e3bab37a
Id : TokenRequest
Type : Error
Message : Failed to request delegation token.
VERBOSE: [12:49:07.423 GMT] Test-FederationTrust : Admin Audit Log: Entered Handler:OnComplete.
VERBOSE: [12:49:07.423 GMT] Test-FederationTrust : Ending processing &
I have removed/deleted the federation and re-created it several times to no avail.
Any suggestions?
Regards,
Luke

Hi All,
I have faced the same issue in test-federationtrust, to solve this issue i have tried mentioned links only. it works for me !!!
Issue Description:
Issue1:
Id         : FederationMetadata
Type       : failed
Issue 2:
Id         : TokenRequest
Type       : Error
Message    : Failed to request delegation token.
http://russburden.wordpress.com/category/microsoft-federation-gateway/
http://vanhybrid.com/2014/01/12/freebusy-in-a-hybrid-environment-fail-and-test-federationtrust-returns-error-failed-to-validate-delegation-token/
http://support.microsoft.com/kb/2555008
http://community.office365.com/en-us/f/158/t/5598.aspx
First of all, we are facing this issue, where Internet connectivity of Exchange Hybrid Server is coming from Webproxy, so need to define Webproxy in Exchange Powershell
First Exchange Powershell will be
Set-ExchangeServer -Identity Exchhub01 -InternetWebProxy
http://10.10.10.10:3120/
Note: Change Exchange Servername and Proxy IP and Port no as per your enviornment.
Second Command will be
Get-FederationTrust | Set-Federationtrust -RefreshMetaData
Third Command Will be
Test-FederationTrust
or
Test-FederationTrust -UserIdentity <OnPremisesMailbox> -verbose
Note: Test-federation trust will show you the status of Federation Certificate, it should be valid, it takes 5-8 hours to become valid from ExpiryThanks
Kirpal Singh

UNICODE Registry APIs Test Result Failed

Hi Experts,
I am currently performing HCK (windows 8.1) on my Windows 2008 R2 and one of the tests is the UNICODE Registry APIs Test. After running the task, the result for UNICODE test is FAILED. Upon checking the logs, Most errors are about Registry Key Create specifically
to create many levels of subkeys. It says "found "HKEY(0x00000000000000B0)\REGISTRY BETA Create TEST\ create many levels of subkeys\create many levels of subkeys\create many levels of subkeys\create many levels of subkeys\create many levels of subkeys\"but
the test did not create it.
In the help file, there is no information about this test. I hope you can help me with this issue.
Best Regards,
RichenVictor

These API aren't permitted at all. See
Supported Win32 APIs for Windows Phone 8 .
What specifically are you trying to do with these API? There may be other ways to achieve the same overall goal, although the config manager calls suggest the app may be attempting something beyond the scope of a Windows Phone app.
For file handling CreateFile2 and FindFirstFileExW are supported.

Test connection failed for resource(s): AD: == No route to host\n

Hi, First of all I would like to tell you that the application was running fine few days back, this issue has come suddenly.
I am getting following error while doing connection test for AD with SUN IDM:
Test connection failed for resource(s): AD: ==> No route to host\n
and when I try to open the detail for windows active directory arrow mark from the resource tab, Its giving me below error:
Error iterating over objects ==> com.waveset.util.WavesetException: ==>java.net.NoRouteToHostException: No route to host
I tried to google on this but all are pointing to some network/firewall problem.
Can anybody suggest me the correction ways to resolve this problem. Any idea how I can proceed further.
Thanks,
Jimmy

First of all, I dont know if you even done the proper fault elimination
No route to host is indicative of a network problem that could be based on several different faults.
Simplest way to check, log in to the system running your IdM.
first check if your nameservice is working
nslookup <your fully qualified hostname for the AD gateway>
idmmgr@unix103a:$ nslookup idm-gw.company.com
Server:         139.188.2.1
Address:        139.188.2.1#53
idm-gw.company.com canonical name = win050a.company.com.
Name:   win050a.company.com
Address: 171.39.88.145if you get the right response there
try pinging the returned address
idmmgr@unix103a:$ ping 171.39.88.145
171.39.88.145 is aliveIf you have a routing problem it will probably show above...
if the route to the gateway works, it might be the gateway that cant talk to the AD
Just follow the track manually and if it stops working from one point, go past that point (if you can) and see if it works beyond it.
Either way, whatever resource is pointed out in the connectinfo in the pertinent adaptor or connector should work from the prompt of the system running it, if not, then you can start unraveling it from there.

IWeb Test Connection Fail

Hi Folks, I am sure that their have been a million questions on this subject on the Test Connection failing when testing your connection to the host.
I am not sure if a solution has been found. I am having this problem and need a solution. I would like to publish through the iWeb FTP page as this is a very simple process. I tried to publish via Cyberduck and this worked ok. However the simplicity of the iWeb publisher is what intrest's me.
Does anybody know of a solution?
Many thanks
Paul

Yes, there are a million questions about this.
This is the usual answer :
When iWeb tests the connection, it tries to write a file on the server based on the server settings you provide.
When it can write, the test is ok.
It does not mean that it is the right location where you should publish your webpages. Only that the location is writable.
If the test fails, it's usually the pathname that is wrong or incomplete. See the FAQ where you host your website to learn what the correct pathname is.
If you already have a website, check the settings of that website and use those.

Hard drive i/o error, spinning beachballs. PASSES Smart test, but fails two specific parameters:

I'm on a Macbook from early 2007.
First off, I'm fully aware that my HD is probably on its last legs and I have two gigantic TB external HDs on which there are multiple images of the entire drive, so data loss is not currently a problem for me. I've also just finished college assignments for the summer so I can afford to mess around with this a bit before taking the plunge and replacing it.
What intrigues me is this. The machine has been extremely slow for a long time. Recently I disabled swapping and the speed rocketed, presumably due to the HD being utilized less during usage. Now the downside to disabling swapping is that when Safari Web Content gets out of control as it always eventually does, you can have a full on system hang which requires a forced shutdown through the power button. So it's very possible that the issues I'm currently experiencing are to do with the machine being improperly shut down one too many times and somehow damaging the drive itself.
But anyway, this is the interesting aspect. Using TTP I ran a SMART test on the internal HD from one of the bootable partitions on one of the external ones, and to my astonishment, it actually PASSES the smart test. The only two parameters which fail are the following:
Raw Read Error Rate
Write Error Count
An image of the SMART test results is attached:
Now to give you an example of the kind of issues I'm having, in order to take that screenshot I used "Grab". When searching for Grab in spotlight it gave me results from the internal HD and from all the various backup drives I have attached. I opened the internal copy and one from a backup partition on another drive (neither of which currently booted from). The one from the backup bounced and opened. The one from internal bounced about 15 times, the spotlight bar hung with a spinning beacball, and I ended up force quitting because I got sick of waiting for it. That's the major symptom of the issue I'm having.
Now here's the reason I'm posting. As I say I know this drive is about to go so there's no need to lecture me about that, I can't replace it immediately but plan to in the very near future when I have a chance. My question is this. Those two specific failed SMART results, what exactly would cause them in terms of HD problems? Bearing in mind that it passes every single other SMART parameter, am I looking at unmapped bad blocks, a physical problem with the head, a loose wire, a bad motor, or what? I'm just wondering specifically what might be wrong with the drive, out of pure curiosity more so than anything else. The fact that most parameters pass suggests to me that it's one very specific malfunction as opposed to the drive generally imploding.
A surface scan from TTP crashed, but not before giving me about 30 "Used block is not a file" messages.
Finally, to temporarily use this drive, what's the procedure? If it's unmapped bad blocks, to I erase and install, or do I go into the whole "zero all data, then reformat" option? I have a backup image taken last night from the external drive which I can restore to the internal any time I want, and as I say with so many backups and so few deadlines ahead of me I don't mind messing around a bit and experimenting.
So if it IS a bad block issue, what does one do to force it to map them?

Had a feeling. As I say it's already fully backed up and ATM I'm running the machine off a partition on the external. But as I say, I'm curious as to what's actually wrong with it - what type of damage / failure would cause those specific smart parameters to fail but not the rest? The motor, the head, the disk surface, what?

Test Connection failed in Crystal Reports for Eclipse using SQL Server 2008

I installed an SQL Server Express 2008 on my local PC (Window XP SP3). I downloaded sqljdbc4.jar to Crystal Reports for Eclipse
IDE library path and tried to Test Connection, but got the Ping failed message : The TCP/IP connection to the host localhost, port 1433 has failed. It said that check that an instance of SQL Server is running on the host (I saw SQL Server SQLEXPRESS is Running on my PC) and accepting TCP/IP connection at the port (I enabled TCP/IPin my PC's SQL Server Network Configuration),
and that no firewall is blocking TCP connection to the port(I turned OFF Window Firewall on my OC). Can anyone tell me how can I fix this problem ?

Hi,
Check the below thread also:
http://scn.sap.com/thread/1634856
Thanks,
DJ

Siebel 8.x and OPA 10.3.0: 'WD Smoke Test' error - 'Failed to load case'

Hi Experts,
I installed OPA Connector for Siebel and installation finally completed successfully. After that, I went to "Finalize & Validate Installation" step. I updated <ds_url>, <wd_ext_url>, <wd_int_url> with the correct host & port.
But when i click "WD Smoke Test", I'm getting following error on server console(deployed to weblogic).
ERROR com.oracle.determinations.web.platform.controller.actions.StartSessionAction - Transaction result errors for case ID [,SADMIN,0-1,AdminSmokeTest]:
ERROR com.oracle.determinations.web.platform.controller.actions.StartSessionAction - Failed to load data: Error running sub-process 'Policy Automation RetreiveSession Impl' at step 'Retrieve Session'.(SBL-BPR-00183)
ERROR com.oracle.determinations.web.platform.servlet.WebDeterminationsServletUtility - com.oracle.determinations.web.platform.exceptions.error.FailedToLoadCaseError: Could not load case: ,SADMIN,0-1,AdminSmokeTest
com.oracle.determinations.web.platform.exceptions.error.FailedToLoadCaseError: Could not load case: ,SADMIN,0-1,AdminSmokeTest
     at com.oracle.determinations.web.platform.controller.actions.StartSessionAction.getResource(StartSessionAction.java:85)
     at com.oracle.determinations.web.platform.servlet.WebDeterminationsServlet.doGet(WebDeterminationsServlet.java:80)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:707)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
     at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
     at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
In the opened popup, i got the following error:
[An error occurred while loading case ID ', SADMIN, 0-1, AdminSmokeTest'.
This error has been logged and is available in the application logs.
For support and assistance please contact [email protected]]
Please suggest.

Hello,
Can you please navigate to Adminstration - Business Process > Workflow Deployment and check how many Active instances are present in Siebel Repository.
It looks to me either "'Policy Automation RetreiveSession Impl" workflow is not active or "'Policy Automation RetreiveSession Impl" workflow is active twice.
In either case please active WF or expire both version and activate freshly.
Best Regards,
Nishant

Test Connection fails for VC system of type Web Service

Hi All
I ve created a VC system of the type Web Service in Portal. In this VC system, I have given Url of the Enterprise Service that I want to use in VC.
(for eg: http://erp.esworkplace.sap.com/sap/bc/srt/wsdl/sdef_ECC_SALESORDER002QR/wsdl11/ws_policy/document?sap-client=800)
In the next step, I did user mapping for the VC user that will be consuming this Enterprise Service.
The system was created successfully but when I did Connection Tests , I got the following exception:
Test Details:
The test consists of the following steps:
1. Retrieve the default alias of the system
2. Check the connection to the backend application using the connector defined in this system object
Results
Retrieval of default alias successful
Connection failed. Make sure that Single Sign-On is configured correctly
Do I need to do any more configurations before I can use such ES portal system in my VC work studio ?
I understand that I have provided little information about the exception thrown by Portal.
I kindly request you to feel free in asking any other details about the same.
Regards
Kapil S Kamble

Hi Natty
thanks for your immediate reply.
I followed your instructions and created iView of the type URL and set the fetch mode property to 'server side' as told.
Initially, I gave 'http://www.sap.com' as the Url and I was successful in opening the site.
Later, when I gave Enterprise Service url and tried to preview the iView, I got the following exception:
*'http://erp.esworkplace.sap.com/sap/bc/srt/wsdl/sdef_ECC_SALESORDER002QR/wsdl11/ws_policy/document?sap-client=800
Error # 401'*
I ll need to give username and password. But how do i give them as parameters?
Please note, these parameteres are appended to the Url. So, I fear that if url of Enterprise service is changed, then it wont open.
what do you think ?
Kapil

Air project works in test but fails when installed.

I have a little project I'm trying to put together as a stand-alone widget. It loads some sounds that are set up in sets and saved in a subdirectory of the application directory. I have a movie clip in the library that appears when the "Config" button is pressed.
Works great in test mode. The sounds are loaded and play. The config screen shows up when the button is pressed. The components (two sliders) work and their listeners fire. Wonderful!
But when I pack it up as an installable AIR file and then actually install it on my poncuter, epic fail. The sliders don't appear, the config button doesn't call up the configure movieClip and no sounds are played. The buttons that I placed on the stage at design time appear but don't appear to function. Nothing I added programmatically appears.
Is this an Adobe CS3 problem or did I miss something in the security sandbox? No files are being written to, I'm getting a directory listing of ./sets and then opening the files in that directory where .isDirectory comes up false. The files are XML and point to a folder off the ./sets folder and the files in that set.
I could probably track this but I have no experience debugging an AIR project. Trace is not working in development. How do people debug the final? Output to a dynamic text field?

Sorry to hear you are having a tough go of it...
there should be no reasons that your application functions differently debugging than when you install the application so the behavior you are seeing is likely something easy to fix (as opposed to having to re-write a bunch of AS code :D).
Couple of Questions:
1.) Are you using CS3 as-is out of the box - or did you manually upgrade your AIR SDK inside Flash Professional to target a later version?
2.) What version of AIR are you targeting?
3.) What version of AIR do you have installed on your system?
4.) What OS are you running on?
5.) Can you install any AIR applications on your machine and have them run properly? (Bunch of AIR apps here: http://www.adobe.com/go/airmarketplace)
6.) It sounds like you are likely using CS3 and not the command line tools - but if you are using the command line tools (ADT) to create your AIR package what command line do you use to create it?
That should help get things rolling...but likely the best course of action is for you to send us your project so we can take a look. You can send your project to cthilgen at adobe.com - please do not send a zip as our mail system will auto-reject it.
Also, you should be able to get trace output. If you are using CS3 the trace output goes to the output panel. (Windows->Output) If you are using the AIR command line tools (ADL) - debug output is enabled by default (you have to manually pass -nodebug to turn it off).
Hope this helps.
Thanks,
Chris Thilgen
AIR Engineering

Test-CsGroupExpansion Failed

Similar Messages

Maybe you are looking for