Testing remote sites
Is this possible yet? If so, how do I go about doing this? I would like to test to see how a live site performs across many devices.
Hi,
Currently this isn't possible with Device Cental, which is designed to support development locally. But thank you for the suggestion and we will certainly consider it.
Regards,
Mark
Similar Messages
-
Remote and Testing Server Site Definitions
I am confused about what information I should put in my
remote site definition info and testing server FTC Host directory
text boxes. My host placed 3 directories: database, log, and www on
my server and Dreamweaver placed two directories, Connections and
_mmServerScripts in the same directory as the above 3. I have
placed all of my site files, including my home page and folders in
the www directory and my Access database in the database directory.
Dreamweaver placed the connection info in the Connections folder an
d _mmServerScripts in the same directory.
In order to construct my local site to match the remote site,
I created a www folder on my local site and placed all of my HTML
files and supporting folders in it.
From various Adobe Tech Notes I have read, I was led to
believe my FTP host directory
Should be www/. However, when I do this and create a new web
page on my local site and upload it to my remote site, Dreamweaver
creates a new www directory inside of the one my host created on
the remote site and uploads the file to it instead of placing it in
the www directory my host created. Also, when I use F12 to test my
page in my browser I get a 404 page not found because Dreamweaver
placed a www in the page URL that shouldn’t be there and
after I remove it I’m able to see my page in my browser. My
URL prefix on my testing server site definition is:
http://I.P.number.html.
What am I not doing right?
Should I use www/ as my FTP host directory or leave it blank?
Also, what should my URL prefix be?
Thanks for your help.What you need to do is set up so that in the remote server
you point to the
www level on the server, and don't replicate this locally.
Paul Whitham
Certified Dreamweaver MX2004 Professional
Adobe Community Expert - Dreamweaver
Valleybiz Internet Design
www.valleybiz.net
"Jim_Moore" <[email protected]> wrote in
message
news:[email protected]...
>I am confused about what information I should put in my
remote site
>definition
> info and testing server FTC Host directory text boxes.
My host placed 3
> directories: database, log, and www on my server and
Dreamweaver placed
> two
> directories, Connections and _mmServerScripts in the
same directory as the
> above 3. I have placed all of my site files, including
my home page and
> folders
> in the www directory and my Access database in the
database directory.
> Dreamweaver placed the connection info in the
Connections folder an d
> _mmServerScripts in the same directory.
>
> In order to construct my local site to match the remote
site, I created a
> www
> folder on my local site and placed all of my HTML files
and supporting
> folders
> in it.
>
> From various Adobe Tech Notes I have read, I was led to
believe my FTP
> host
> directory
> Should be www/. However, when I do this and create a new
web page on my
> local
> site and upload it to my remote site, Dreamweaver
creates a new www
> directory
> inside of the one my host created on the remote site and
uploads the file
> to it
> instead of placing it in the www directory my host
created. Also, when I
> use
> F12 to test my page in my browser I get a 404 page not
found because
> Dreamweaver placed a www in the page URL that shouldn?t
be there and after
> I
> remove it I?m able to see my page in my browser. My URL
prefix on my
> testing
> server site definition is:
http://I.P.number.html.
>
> What am I not doing right?
> Should I use www/ as my FTP host directory or leave it
blank?
> Also, what should my URL prefix be?
>
> Thanks for your help.
>
> -
File does not exist on remote site, yet it does
I have been trying to understand how Dreamweaver handles remote files in CS5.
My server is setup as a remote server and a test server.
I open the remote file, it offers to get dependencies, so I click yes.
I click on Live view, then it tries to show me the following url
http://my_site.com/public_html/path/to/my/file/file.php
It should not put public_html in the path, and I did not specify this in my site setup. My root setting is /.
Anyway, If I change the url manually, then it shows correctly. Then it offers to discover dunamically linked files, which I agree to.
Now it tells me that 'Dynamically-related files could not be resolved because the site definition is not correct for this server'
If I try to open one of the files that it has discovered, I am told that it is not on the disk, so would I like to 'get it', so I agree.
Finally, I am told that 'Get operation failed since linked-file.php does not exist on remote site'
I suspect that this is all to do with my site definition, but I fiddled with the settings and can't resolve this. I think that the whole problem goes back to Dreamweaver's insistance on putting public_html in the path, but I can't stop it doing so.
Any suggestions?
Thanks
ianHi,
Well, yes I did manage to fix the dynamically linked resources issue. As mentioned above, I did need to mention public_html in my Root Directory setting in server setup (silly of me).
I had tried this at first, but it didn't work, as I had the server set as a test server and not a remote server, anyway, i now have it set as both and all is well.
Except that, the first issue that mentioned is still with me: namely, dreamweaver mentions the public_html in the url path when on live view, which is not correct and I don't know where it is inferring this from. I can change it manually, but this doesn't seem right to me. Am I still missing a setting?
In anwer to the questions:
1) My setting (now) in the Root Directory setting in DW is: /public_html/
2) My actual path on the server (that i mention in php scripts) is: /home/login_name/public_html//path/to/my/file/file.php
[In the advanced settings of DW site setup on the Local Info page I have set Links relative to Document option, although it does not seem to make a difference when I change it to Site Root.]
Any suggestions appreciated.
Thanks
Ian -
The WSDL data cannot be retrieve from remote site
I am a new guy learning web services with NetBeans 5.5 and meet some problem in retrieving wsdl data from remote site.
I create a web service "WSTestServer" at Sun Application Server PE8.2 with real IP, say 111.110.11.10:8888, and there's a class "TestWS" with a method "getWS" to return a String. The server (or machine) name is ultra20. So, by following steps in NetBeans, I can get a wsdl file after generating the web service and it can be viewed at
http://111.110.11.10:8888/WSTestServer/TestWS?WSDL
Then, I create a web service client at the same machine, it is available to test this method by clicking Web Service Reference item in NetBeans and select "getWS" method to get that String.
However, when I create a web service client at remote site, it doesn't work and show exception message like
cannot find domain http://ultra20:8888/WSTestServer/TestWS....
I go back to check wsdl file, at the last line, it prints like
<soap:address location="http://ultra20:8888/WSTestServer/TestWS".....
If I test this case in LAN, e.g., the server IP becomes 192.168.1.2 and client IP is 192.168.1.3, then it works since machine name can be recognized within the same local area network. I try to revise the wsdl file above to replace machine name as real IP, but it is automatically changed back with machine name while deploying and copy the revised one as xxx.wsdl__orig.
Should I do additional configuration setup for server site? Such as, registering a domain name like aaa.bbb.edu instead of 111.110.11.10?
Any comment and help for this subject is appreciated!!
Thank you so much!Works as designed,from documentation:
The database also retrieves all triggers and constraints defined on the table except for referential integrity constraints that reference other tables.
The retrieved indexes, triggers, and constraints have recycle bin names. Therefore it is advisable to query the USER_RECYCLEBIN view before issuing a FLASHBACK TABLE ... TO BEFORE DROP statement so that you can rename the retrieved triggers and constraints to more usable names.
For details see the FLASHBACK TABLE command description for your unknown database version.
Werner -
Internet connexion problem for remote site in Site to site VPN asa 5505
Hi all
I'm configuring a site to site Ipsec VPN in 2 sites using ASA 5505 V 8.2, The VPN is working fine i can ping machine in the 2 sides but the problem is the remote site dont' have internet.
The architecture is, we 2 site Site1 is the main site and Site2 is secondary site there will be Site3, ...
The internet connection is based in Site1 and site2 and site 3 will have internet connection through Site1. Site1, Site2 and Site 3 is interconnected by Ipsec VPN.
Here is my ASA 5505 Configuration :
SITE 1:
ASA Version 8.2(5)
hostname test-malabo
domain-name test.mg
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd ta.qizy4R//ChqQH encrypted
names
interface Ethernet0/0
description "Sortie Internet"
switchport access vlan 2
interface Ethernet0/1
description "Interconnexion"
switchport access vlan 171
interface Ethernet0/2
description "management"
switchport access vlan 10
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 41.79.49.42 255.255.255.192
interface Vlan10
nameif mgmt
security-level 0
ip address 10.12.1.100 255.255.0.0
interface Vlan171
nameif interco
security-level 0
ip address 10.22.19.254 255.255.255.0
ftp mode passive
dns server-group DefaultDNS
domain-name test.mg
object-group network LAN-MALABO
description LAN DE MALABO
network-object 192.168.1.0 255.255.255.0
object-group network LAN-BATA
description LAN DE BATA
network-object 192.168.2.0 255.255.255.0
object-group network LAN-LUBA
description LAN DE LUBA
network-object 192.168.3.0 255.255.255.0
access-list interco_1_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.3.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
mtu interco 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
icmp permit any interco
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (interco) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 41.79.49.1 1
route interco 192.168.3.0 255.255.255.0 10.22.19.5 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map interco_map0 1 match address interco_1_cryptomap
crypto map interco_map0 1 set pfs group1
crypto map interco_map0 1 set peer 10.22.19.5
crypto map interco_map0 1 set transform-set ESP-3DES-SHA
crypto map interco_map0 interface interco
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto isakmp enable interco
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.1.0 255.255.255.0 inside
telnet 10.12.0.0 255.255.0.0 mgmt
telnet timeout 30
ssh 192.168.1.0 255.255.255.0 inside
ssh 10.12.0.0 255.255.0.0 mgmt
ssh timeout 30
console timeout 0
management-access interco
dhcpd option 3 ip 192.168.1.1
dhcpd address 192.168.1.100-192.168.1.254 inside
dhcpd dns 41.79.48.66 8.8.8.8 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username admin password eY/fQXw7Ure8Qrz7 encrypted privilege 15
tunnel-group 10.22.19.5 type ipsec-l2l
tunnel-group 10.22.19.5 ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 60 retry 5
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect snmp
inspect icmp
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:5aa0d27f15e49ea597c8097cfdb755b8
: end
SITE2:
ASA Version 8.2(5)
hostname test-luba
domain-name test.eg
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
description "Sortie Interco-Internet"
switchport access vlan 2
interface Ethernet0/1
description "management"
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.3.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.22.19.5 255.255.255.0
interface Vlan10
nameif mgmt
security-level 0
ip address 10.12.1.101 255.255.0.0
ftp mode passive
dns server-group DefaultDNS
domain-name test.eg
object-group network LAN-MALABO
description LAN DE MALABO
network-object 192.168.1.0 255.255.255.0
object-group network LAN-BATA
description LAN DE BATA
network-object 192.168.2.0 255.255.255.0
object-group network LAN-LUBA
description LAN DE LUBA
network-object 192.168.3.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.3.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.3.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside) 0 access-list inside_nat0_outbound
route outside 0.0.0.0 0.0.0.0 10.22.19.254 1
route outside 192.168.1.0 255.255.255.0 10.22.19.254 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map0 1 match address outside_1_cryptomap
crypto map outside_map0 1 set pfs group1
crypto map outside_map0 1 set peer 10.22.19.254
crypto map outside_map0 1 set transform-set ESP-3DES-SHA
crypto map outside_map0 interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.12.0.0 255.255.0.0 mgmt
telnet timeout 30
ssh 192.168.3.0 255.255.255.0 inside
ssh 10.12.0.0 255.255.0.0 mgmt
ssh timeout 30
console timeout 0
management-access outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username admin password eY/fQXw7Ure8Qrz7 encrypted privilege 15
tunnel-group 10.22.19.254 type ipsec-l2l
tunnel-group 10.22.19.254 ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 60 retry 5
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:185bd689118ba24f9a0ef2f7e80494f6
Can anybody help why my remote site can't connect to Internet.
REgards,
RaitsarevoHi Carv,
Thanks for your reply. i have done finally
i used no crypto ipsec nat-transparency udp-encapsulation in my end router only.
and in remote access VPN i have enabled UDP for client configuration. the most imprtant is i have given IP add of same LAN pool to VPN user,
Regards,
Satya.M -
VPN Clients cannot access remote site
Hey there,
I am pretty new in configuring Cisco devices and now I need some help.
I have 2 site here:
site A
Cisco 891
external IP: 195.xxx.yyy.zzz
VPN Gateway for Remote users
local IP: VLAN10 10.133.10.0 /23
site B
Cisco 891
external IP: 62.xxx.yyy.zzz
local IP VLAN10 10.133.34.0 /23
Those two sites are linked together with a Site-to-Site VPN. Accessing files or ressources from one site to the other is working fine while connected to the local LAN.
I configured VPN connection with Radius auth. VPN clients can connect to Site A, get an IP adress from VPN Pool (172.16.100.2-100) and can access files and servers on site A. But for some reason they cannot access ressources on site B. I already added the site B network to the ACL and when connecting with VPN it shows secured routes to 10.133.10.0 and 10.133.34.0 in the statistics. Same thing for other VPN Tunnels to ERP system.
What is missing here to make it possible to reach remote sites when connected through VPN? I had a look at the logs but could not find anything important.
Here is the config of site A
Building configuration...
Current configuration : 24257 bytes
version 15.2
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Englerstrasse
boot-start-marker
boot config usbflash0:CVO-BOOT.CFG
boot-end-marker
aaa new-model
aaa group server radius Radius-AD
server 10.133.10.5 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_2 group Radius-AD local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_2 local
aaa session-id common
clock timezone Berlin 1 0
clock summer-time Berlin date Mar 30 2003 2:00 Oct 26 2003 3:00
crypto pki trustpoint TP-self-signed-27361994
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-27361994
revocation-check none
rsakeypair TP-self-signed-27361994
crypto pki trustpoint test_trustpoint_config_created_for_sdm
subject-name [email protected]
revocation-check crl
crypto pki certificate chain TP-self-signed-27361994
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32373336 31393934 301E170D 31323038 32373038 30343238
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D323733 36313939
3430819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100B709
64CE1874 BF812A9F 0B761522 892373B9 10F0BB52 6263DCDB F9877AA3 7BD34E53
BCFDA45C 2A991777 4DDC7E6B 1FCEE36C B6E35679 C4A18771 9C0F871F 38310234
2D89A4FF 37B616D8 362B3103 A8A319F2 10A72DC7 490A04AC 7955DF68 32EF9615
9E1A3B31 2A1AB243 B3ED3E35 F4AAD029 CDB1F941 5E794300 5C5EF8AE 5C890203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14D0F5E7 D3A9311D 1675AA8F 38F064FC 4D04465E F5301D06 03551D0E
04160414 D0F5E7D3 A9311D16 75AA8F38 F064FC4D 04465EF5 300D0609 2A864886
F70D0101 05050003 818100AB 2CD4363A E5ADBFB0 943A38CB AC820801 117B52CC
20216093 79D1F777 2B3C0062 4301CF73 094B9CA5 805F585E 04CF3301 9B839DEB
14A334A2 F5A5316F C65EEF21 0B0DF3B5 F4322440 F28B984B E769876D 6EF94895
C3D5048A A4E2A180 12DF6652 176942F8 58187D7B D37B1F1A 4DDD7AE9 5189F9AF
AF3EF676 26AD3F31 D368F5
quit
crypto pki certificate chain test_trustpoint_config_created_for_sdm
no ip source-route
ip auth-proxy max-login-attempts 5
ip admission max-login-attempts 5
no ip bootp server
no ip domain lookup
ip domain name yourdomain.com
ip inspect log drop-pkt
ip inspect name CCP_MEDIUM appfw CCP_MEDIUM
ip inspect name CCP_MEDIUM ftp
ip inspect name CCP_MEDIUM h323
ip inspect name CCP_MEDIUM sip
ip inspect name CCP_MEDIUM https
ip inspect name CCP_MEDIUM icmp
ip inspect name CCP_MEDIUM netshow
ip inspect name CCP_MEDIUM rcmd
ip inspect name CCP_MEDIUM realaudio
ip inspect name CCP_MEDIUM rtsp
ip inspect name CCP_MEDIUM sqlnet
ip inspect name CCP_MEDIUM streamworks
ip inspect name CCP_MEDIUM tftp
ip inspect name CCP_MEDIUM udp
ip inspect name CCP_MEDIUM vdolive
ip inspect name CCP_MEDIUM imap reset
ip inspect name CCP_MEDIUM smtp
ip cef
no ipv6 cef
appfw policy-name CCP_MEDIUM
application im aol
service default action allow alarm
service text-chat action allow alarm
server permit name login.oscar.aol.com
server permit name toc.oscar.aol.com
server permit name oam-d09a.blue.aol.com
audit-trail on
application im msn
service default action allow alarm
service text-chat action allow alarm
server permit name messenger.hotmail.com
server permit name gateway.messenger.hotmail.com
server permit name webmessenger.msn.com
audit-trail on
application http
strict-http action allow alarm
port-misuse im action reset alarm
port-misuse p2p action reset alarm
port-misuse tunneling action allow alarm
application im yahoo
service default action allow alarm
service text-chat action allow alarm
server permit name scs.msg.yahoo.com
server permit name scsa.msg.yahoo.com
server permit name scsb.msg.yahoo.com
server permit name scsc.msg.yahoo.com
server permit name scsd.msg.yahoo.com
server permit name cs16.msg.dcn.yahoo.com
server permit name cs19.msg.dcn.yahoo.com
server permit name cs42.msg.dcn.yahoo.com
server permit name cs53.msg.dcn.yahoo.com
server permit name cs54.msg.dcn.yahoo.com
server permit name ads1.vip.scd.yahoo.com
server permit name radio1.launch.vip.dal.yahoo.com
server permit name in1.msg.vip.re2.yahoo.com
server permit name data1.my.vip.sc5.yahoo.com
server permit name address1.pim.vip.mud.yahoo.com
server permit name edit.messenger.yahoo.com
server permit name messenger.yahoo.com
server permit name http.pager.yahoo.com
server permit name privacy.yahoo.com
server permit name csa.yahoo.com
server permit name csb.yahoo.com
server permit name csc.yahoo.com
audit-trail on
parameter-map type inspect global
log dropped-packets enable
multilink bundle-name authenticated
redundancy
ip tcp synwait-time 10
class-map match-any CCP-Transactional-1
match dscp af21
match dscp af22
match dscp af23
class-map match-any CCP-Voice-1
match dscp ef
class-map match-any sdm_p2p_kazaa
match protocol fasttrack
match protocol kazaa2
class-map match-any CCP-Routing-1
match dscp cs6
class-map match-any sdm_p2p_edonkey
match protocol edonkey
class-map match-any CCP-Signaling-1
match dscp cs3
match dscp af31
class-map match-any sdm_p2p_gnutella
match protocol gnutella
class-map match-any CCP-Management-1
match dscp cs2
class-map match-any sdm_p2p_bittorrent
match protocol bittorrent
policy-map sdm-qos-test-123
class class-default
policy-map sdmappfwp2p_CCP_MEDIUM
class sdm_p2p_edonkey
class sdm_p2p_gnutella
class sdm_p2p_kazaa
class sdm_p2p_bittorrent
policy-map CCP-QoS-Policy-1
class sdm_p2p_edonkey
class sdm_p2p_gnutella
class sdm_p2p_kazaa
class sdm_p2p_bittorrent
class CCP-Voice-1
priority percent 33
class CCP-Signaling-1
bandwidth percent 5
class CCP-Routing-1
bandwidth percent 5
class CCP-Management-1
bandwidth percent 5
class CCP-Transactional-1
bandwidth percent 5
class class-default
fair-queue
random-detect
crypto ctcp port 10000
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key REMOVED address 62.20.xxx.yyy
crypto isakmp key REMOVED address 195.243.xxx.yyy
crypto isakmp key REMOVED address 195.243.xxx.yyy
crypto isakmp key REMOVED address 83.140.xxx.yyy
crypto isakmp client configuration group VPN_local
key REMOVED
dns 10.133.10.5 10.133.10.7
wins 10.133.10.7
domain domain.de
pool SDM_POOL_2
acl 115
crypto isakmp profile ciscocp-ike-profile-1
match identity group VPN_local
client authentication list ciscocp_vpn_xauth_ml_2
isakmp authorization list ciscocp_vpn_group_ml_2
client configuration address respond
virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA2 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA3 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA4 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA11 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA5 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA1 esp-des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA11
set isakmp-profile ciscocp-ike-profile-1
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to62.20.xxx.xxx
set peer 62.20.xxx.xxx
set transform-set ESP-3DES-SHA
match address 105
crypto map SDM_CMAP_1 2 ipsec-isakmp
description Tunnel to195.243.xxx.xxx
set peer 195.243.xxx.xxx
set transform-set ESP-3DES-SHA4
match address 107
crypto map SDM_CMAP_1 3 ipsec-isakmp
description Tunnel to83.140.xxx.xxx
set peer 83.140.xxx.xxx
set transform-set ESP-DES-SHA1
match address 118
interface Loopback2
ip address 192.168.10.1 255.255.254.0
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
no ip address
spanning-tree portfast
interface FastEthernet1
no ip address
spanning-tree portfast
interface FastEthernet2
no ip address
spanning-tree portfast
interface FastEthernet3
no ip address
spanning-tree portfast
interface FastEthernet4
description Internal LAN
switchport access vlan 10
switchport trunk native vlan 10
no ip address
spanning-tree portfast
interface FastEthernet5
no ip address
spanning-tree portfast
interface FastEthernet6
no ip address
spanning-tree portfast
interface FastEthernet7
no ip address
spanning-tree portfast
interface FastEthernet8
description $FW_OUTSIDE$$ETH-WAN$
ip address 62.153.xxx.xxx 255.255.255.248
ip access-group 113 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip inspect CCP_MEDIUM out
no ip virtual-reassembly in
ip verify unicast reverse-path
duplex auto
speed auto
crypto map SDM_CMAP_1
service-policy input sdmappfwp2p_CCP_MEDIUM
service-policy output CCP-QoS-Policy-1
interface Virtual-Template1 type tunnel
ip unnumbered FastEthernet8
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface GigabitEthernet0
no ip address
shutdown
duplex auto
speed auto
interface Vlan1
no ip address
interface Vlan10
description $FW_INSIDE$
ip address 10.133.10.1 255.255.254.0
ip access-group 112 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
interface Async1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
ip local pool SDM_POOL_1 192.168.10.101 192.168.10.200
ip local pool VPN_Pool 192.168.20.2 192.168.20.100
ip local pool SDM_POOL_2 172.16.100.2 172.16.100.100
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip forward-protocol nd
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet8 overload
ip route 0.0.0.0 0.0.0.0 62.153.xxx.xxx
ip access-list extended VPN1
remark VPN_Haberstrasse
remark CCP_ACL Category=4
permit ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
ip radius source-interface Vlan10
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
access-list 23 remark CCP_ACL Category=17
access-list 23 permit 195.243.xxx.xxx
access-list 23 permit 10.133.10.0 0.0.1.255
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 100 remark CCP_ACL Category=4
access-list 100 permit ip 10.133.10.0 0.0.1.255 any
access-list 101 remark CCP_ACL Category=16
access-list 101 permit udp any eq bootps any eq bootpc
access-list 101 deny ip 10.10.10.0 0.0.0.255 any
access-list 101 permit icmp any any echo-reply
access-list 101 permit icmp any any time-exceeded
access-list 101 permit icmp any any unreachable
access-list 101 deny ip 10.0.0.0 0.255.255.255 any
access-list 101 deny ip 172.16.0.0 0.15.255.255 any
access-list 101 deny ip 192.168.0.0 0.0.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip any any
access-list 102 remark auto generated by CCP firewall configuration
access-list 102 remark CCP_ACL Category=1
access-list 102 deny ip 10.10.10.0 0.0.0.7 any
access-list 102 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 102 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 102 permit icmp any host 62.153.xxx.xxx unreachable
access-list 102 deny ip 10.0.0.0 0.255.255.255 any
access-list 102 deny ip 172.16.0.0 0.15.255.255 any
access-list 102 deny ip 192.168.0.0 0.0.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip host 0.0.0.0 any
access-list 102 deny ip any any log
access-list 103 remark auto generated by CCP firewall configuration
access-list 103 remark CCP_ACL Category=1
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.34.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.34.0 0.0.1.255 192.168.10.0 0.0.1.255
access-list 103 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit ahp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.20.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 103 remark IPSec Rule
access-list 103 permit ip 192.168.10.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 103 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit ahp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit udp any host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp any host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp any host 62.153.xxx.xxx
access-list 103 permit ahp any host 62.153.xxx.xxx
access-list 103 permit udp host 194.25.0.60 eq domain any
access-list 103 permit udp host 194.25.0.68 eq domain any
access-list 103 permit udp host 194.25.0.68 eq domain host 62.153.xxx.xxx
access-list 103 deny ip 10.10.10.0 0.0.0.7 any
access-list 103 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 103 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 103 permit icmp any host 62.153.xxx.xxx unreachable
access-list 103 deny ip 10.0.0.0 0.255.255.255 any
access-list 103 deny ip 172.16.0.0 0.15.255.255 any
access-list 103 deny ip 192.168.0.0 0.0.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip host 0.0.0.0 any
access-list 103 deny ip any any log
access-list 104 remark CCP_ACL Category=4
access-list 104 permit ip 10.133.10.0 0.0.1.255 any
access-list 105 remark CCP_ACL Category=4
access-list 105 remark IPSec Rule
access-list 105 permit ip 10.133.10.0 0.0.1.255 10.133.20.0 0.0.0.255
access-list 106 remark CCP_ACL Category=2
access-list 106 remark IPSec Rule
access-list 106 deny ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 192.168.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.133.20.0 0.0.0.255
access-list 106 permit ip 10.10.10.0 0.0.0.7 any
access-list 106 permit ip 10.133.10.0 0.0.1.255 any
access-list 107 remark CCP_ACL Category=4
access-list 107 remark IPSec Rule
access-list 107 permit ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 107 remark IPSec Rule
access-list 107 permit ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 108 remark Auto generated by SDM Management Access feature
access-list 108 remark CCP_ACL Category=1
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq telnet
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq 22
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq www
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq 443
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq cmd
access-list 108 deny tcp any host 10.133.10.1 eq telnet
access-list 108 deny tcp any host 10.133.10.1 eq 22
access-list 108 deny tcp any host 10.133.10.1 eq www
access-list 108 deny tcp any host 10.133.10.1 eq 443
access-list 108 deny tcp any host 10.133.10.1 eq cmd
access-list 108 deny udp any host 10.133.10.1 eq snmp
access-list 108 permit ip any any
access-list 109 remark CCP_ACL Category=1
access-list 109 permit ip 10.133.10.0 0.0.1.255 any
access-list 109 permit ip 10.10.10.0 0.0.0.7 any
access-list 109 permit ip 192.168.10.0 0.0.1.255 any
access-list 110 remark CCP_ACL Category=1
access-list 110 permit ip host 195.243.xxx.xxx any
access-list 110 permit ip host 84.44.xxx.xxx any
access-list 110 permit ip 10.133.10.0 0.0.1.255 any
access-list 110 permit ip 10.10.10.0 0.0.0.7 any
access-list 110 permit ip 192.168.10.0 0.0.1.255 any
access-list 111 remark CCP_ACL Category=4
access-list 111 permit ip 10.133.10.0 0.0.1.255 any
access-list 112 remark CCP_ACL Category=1
access-list 112 permit udp host 10.133.10.5 eq 1812 any
access-list 112 permit udp host 10.133.10.5 eq 1813 any
access-list 112 permit udp any host 10.133.10.1 eq non500-isakmp
access-list 112 permit udp any host 10.133.10.1 eq isakmp
access-list 112 permit esp any host 10.133.10.1
access-list 112 permit ahp any host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1645 host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1646 host 10.133.10.1
access-list 112 remark auto generated by CCP firewall configuration
access-list 112 permit udp host 10.133.10.5 eq 1812 host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1813 host 10.133.10.1
access-list 112 permit udp host 10.133.10.7 eq domain any
access-list 112 permit udp host 10.133.10.5 eq domain any
access-list 112 deny ip 62.153.xxx.xxx 0.0.0.7 any
access-list 112 deny ip 10.10.10.0 0.0.0.7 any
access-list 112 deny ip host 255.255.255.255 any
access-list 112 deny ip 127.0.0.0 0.255.255.255 any
access-list 112 permit ip any any
access-list 113 remark CCP_ACL Category=1
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.34.0 0.0.1.255 192.168.10.0 0.0.1.255
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.60.16.0 0.0.0.255 192.168.10.0 0.0.1.255
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.60.16.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 113 permit udp host 83.140.100.4 host 62.153.xxx.xxx eq non500-isakmp
access-list 113 permit udp host 83.140.100.4 host 62.153.xxx.xxx eq isakmp
access-list 113 permit esp host 83.140.100.4 host 62.153.xxx.xxx
access-list 113 permit ahp host 83.140.100.4 host 62.153.xxx.xxx
access-list 113 permit ip host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit ip host 84.44.xxx.xxx host 62.153.xxx.xxx
access-list 113 remark auto generated by CCP firewall configuration
access-list 113 permit udp host 194.25.0.60 eq domain any
access-list 113 permit udp host 194.25.0.68 eq domain any
access-list 113 permit udp host 194.25.0.68 eq domain host 62.153.xxx.xxx
access-list 113 permit udp host 194.25.0.60 eq domain host 62.153.xxx.xxx
access-list 113 permit udp any host 62.153.xxx.xxx eq non500-isakmp
access-list 113 permit udp any host 62.153.xxx.xxx eq isakmp
access-list 113 permit esp any host 62.153.xxx.xxx
access-list 113 permit ahp any host 62.153.xxx.xxx
access-list 113 permit ahp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit esp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 113 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.34.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 113 permit ahp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 113 remark IPSec Rule
access-list 113 permit ip 192.168.10.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 113 permit esp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 113 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.20.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 113 remark Pop3
access-list 113 permit tcp host 82.127.xxx.xxx eq 8080 host 62.153.xxx.xxx
access-list 113 remark Pop3
access-list 113 permit tcp any eq pop3 host 62.153.xxx.xxx
access-list 113 remark SMTP
access-list 113 permit tcp any eq 465 host 62.153.xxx.xxx
access-list 113 remark IMAP
access-list 113 permit tcp any eq 587 host 62.153.xxx.xxx
access-list 113 deny ip 10.133.10.0 0.0.1.255 any
access-list 113 deny ip 10.10.10.0 0.0.0.7 any
access-list 113 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 113 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 113 permit icmp any host 62.153.xxx.xxx unreachable
access-list 113 deny ip 10.0.0.0 0.255.255.255 any
access-list 113 deny ip 172.16.0.0 0.15.255.255 any
access-list 113 deny ip 192.168.0.0 0.0.255.255 any
access-list 113 deny ip 127.0.0.0 0.255.255.255 any
access-list 113 deny ip host 255.255.255.255 any
access-list 113 deny ip host 0.0.0.0 any
access-list 113 deny ip any any log
access-list 114 remark auto generated by CCP firewall configuration
access-list 114 remark CCP_ACL Category=1
access-list 114 deny ip 10.133.10.0 0.0.1.255 any
access-list 114 deny ip 10.10.10.0 0.0.0.7 any
access-list 114 permit icmp any any echo-reply
access-list 114 permit icmp any any time-exceeded
access-list 114 permit icmp any any unreachable
access-list 114 deny ip 10.0.0.0 0.255.255.255 any
access-list 114 deny ip 172.16.0.0 0.15.255.255 any
access-list 114 deny ip 192.168.0.0 0.0.255.255 any
access-list 114 deny ip 127.0.0.0 0.255.255.255 any
access-list 114 deny ip host 255.255.255.255 any
access-list 114 deny ip host 0.0.0.0 any
access-list 114 deny ip any any log
access-list 115 remark VPN_Sub
access-list 115 remark CCP_ACL Category=5
access-list 115 permit ip 10.133.10.0 0.0.1.255 172.16.0.0 0.0.255.255
access-list 115 permit ip 10.133.34.0 0.0.1.255 172.16.0.0 0.0.255.255
access-list 115 permit ip 10.133.20.0 0.0.0.255 any
access-list 116 remark CCP_ACL Category=4
access-list 116 remark IPSec Rule
access-list 116 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 117 remark CCP_ACL Category=4
access-list 117 remark IPSec Rule
access-list 117 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 118 remark CCP_ACL Category=4
access-list 118 remark IPSec Rule
access-list 118 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 118 remark IPSec Rule
access-list 118 permit ip 192.168.10.0 0.0.1.255 10.60.16.0 0.0.0.255
no cdp run
route-map SDM_RMAP_1 permit 1
match ip address 106
control-plane
mgcp profile default
line con 0
transport output telnet
line 1
modem InOut
speed 115200
flowcontrol hardware
line aux 0
transport output telnet
line vty 0 4
session-timeout 45
access-class 110 in
transport input telnet ssh
line vty 5 15
access-class 109 in
transport input telnet ssh
scheduler interval 500
endThe crypto ACL for the site to site vpn should also include the vpn client pool, otherwise, traffic from the vpn client does not match the interesting traffic for the site to site vpn.
On Site A:
should include "access-list 107 permit ip 172.16.100.0 0.0.0.255 10.133.34.0 0.0.1.255"
You should also remove the following line as the pool is incorrect:
access-list 107 permit ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
On Site B:
should include: permit ip 10.133.34.0 0.0.1.255 172.16.100.0 0.0.0.255"
NAT exemption on site B should also be configured with deny on the above ACL. -
How to access a remote site in dreamweaver
This might seem like a simple question, but i just downloaded DW as a trial, and want to try it out before buying. Now I've done the remote site set up and tested and it says it can connect to my remote site. But I want to now go to the site, log in, and make some changes to the web site pages which are stored there. None of the stuff is stored on my home PC. It's all at the remote site. So how do I edit it? How do I even log in? DW seems intended to work on files on your home PC, and then publish them to a remote site. My problem is it's all ON the remote site.
Hi Nancy,
No, I'm not getting those selections under the file menu. What I've done is go to server, manage servers, and set up a remote server. When I test it it says "dreamweaver connected to your web server succesfully". So I assume that the remote server, at least, is set up properly. I didn't set up a "local site" however. Perhaps that could be it? But those choices are not on the drop-down box, even grayed out. If I click on "open" the box goes to my PC for choices. On the left side it has" My recent documents, desktop, my documents, my network (which doesn't lead anywhere) -
Best option to transmit CSV file as POST data to remote site
I'm quite new to the SAP scene and am tasked with getting some data out of our database and up to a third party web application.
Their API requests the data be formatted as a CSV file and uploaded as an HTTP POST attachment (file upload) to their site.
What's my best approach to this?
We have PI, but I just learned about CL_HTTP_CLIENT and am hoping I can do this move directly from the ABAP environment but am unsure of the sorts of technicalities involved with either of these options.
Can I setup a "service" in PI that simply posts data to a URL (as opposed to sending a SOAP request)?
What sort of setup do I need to do to get CL_HTTP_CLIENT to talk to the remote site? I've tested with HTTP_POST and get an SSL error even when posting to a non-ssl url (http).public
void Save(IPropertyBag
propertyBag, bool clearDirty,
bool saveAllProperties)
object val2 = (object)_event;
propertyBag.Write("Event",
ref val2);
object val3 = (object)_fullload;
propertyBag.Write("FullLoad",
ref val3);
object val4 = (object)_sharedsecret;
propertyBag.Write("SharedSecret",
ref val4);
object val5 = (object)_content;
propertyBag.Write("Content",
ref val5);
object val6 = (object)_clienttype;
propertyBag.Write("ClientType",
ref val6);
object val7 = (object)_clientinfo;
propertyBag.Write("ClientInfo",
ref val7);
object val8 = (object)_clientversion;
propertyBag.Write("ClientVersion",
ref val8);
#endregion
#region IComponent
public
IBaseMessage Execute(IPipelineContext
pc, IBaseMessage inmsg)
//Convert Stream to a string
Stream s =
null;
IBaseMessagePart bodyPart = inmsg.BodyPart;
string separator =
new
Guid().ToString();
inmsg.BodyPart.ContentType =
string.Format("multipart/form-data;
boundary={0}", separator);
//inmsg.BodyPart.Charset = string.Format("US-ASCII");
// NOTE inmsg.BodyPart.Data is implemented only as a setter in the http adapter API and a
//getter and setter for the file adapter. Use GetOriginalDataStream to get data instead.
if (bodyPart !=
null)
s = bodyPart.GetOriginalDataStream();
byte[] bytes =
new
byte[s.Length];
int n = s.Read(bytes, 0, (int)s.Length);
string msg =
new
ASCIIEncoding().GetString(bytes).TrimEnd(null);
//Get boundry value from first line of code
string boundry = msg.Substring(2, msg.IndexOf("\r\n")
- 2);
//Create new start to message with MIME requirements.
msg =
"MIME-Version: 1.0\r\nContent-Type: text/plain; boundary=\"" + boundry +
"\"\r\n" + msg;
//Convert back to stram and set to Data property
inmsg.BodyPart.Data =
new
MemoryStream(Encoding.UTF8.GetBytes(msg));
//reset the position of the stream to zero
inmsg.BodyPart.Data.Position = 0;
return inmsg;
#endregion -
Login wizard - CF9 server - "Coldfusion not is not running on the remote site" - YES it is!
I use Dreamweaver to upkeep sites for several friends and clients. When I use the login wizzard on a server with CF8, it works fine. If I use it on a server with CF9, I can't get past the *Coldfusion not is not running on the remote site* error. Yes it is running. I've tried connecting using FTP, RDS, directly over the network - you name it. Same error.
Any suggestions?
Thanks
RickHi Rick
If you are trying to RDS log in to a remote server the host may have disabled this service... Most do, and should. Allowing remote RDS is a potential security risk. Check with your host to see if this is the case. If it is, it is always better to duplicate your host environment locally, that is be running CF9, and the database, be that MySQL, SQL Server, Access, or whatever locally and do all you development and testing there, then just upload the files when ready.
Hope this helps.
Lawrence Cramer - *Adobe Community Professional*
http://www.Cartweaver.com
Shopping Cart for Adobe Dreamweaver
available in PHP, ColdFusion, and ASP
Stay updated - http://blog.cartweaver.com -
Losing connection to the Domain Controllers at a remote site
We have a remote site with a IPsec tunnel for a site to site connection and there are about a dozen window 7 systems on site. Every 3 to 5 weeks, the systems start to lose the ability to log into the domain. Running some tests, the DNS names
keep resolving, their subnet is setup in Sites and Services to the group with the DC's and they are setup correctly for IP settings but seems like they still can't connect back to the DC's. From there, under network profiles, it says the domain network
is unauthenticated.
The only way we have found to fix this is to dis-join the computer from the domain and rejoin it.
Is there a way from the computer to force it to re-authenticate without having to do this or a better fix?Hello Technsopyder,
Do you means all the Windows 7 use the IPsec will lose connection to the Domain Controllers every 3 to 5 weeks?
Do you receive the error code 5719 and 3210? Could you please provide the whole error message?
Please check if you need to change the password before this issue as Brano Lukic mentioned.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support -
How can I change remote site definition without breaking all of the links?
I've created a website and put it here http://home.comcast.net/~alpsf/index.html to test it during construction. Now when I change the remote site definition on the local site in DW, all of the links are broken. I now suspect the problem is that I made it site root-relative, and DW inserted /~alpsf/ in all of the links. Is there a way to fix this?
Thanks very much.You can do a find and replace to change the links globally. Make sure you do a complete backup of the site prior to doing this incase you don't do it correctly. Let me stress that again, backup your entire site incase you need to restore. If you have created a "new site" and this will not be part of the /~alpsf site, then you will need to define a new site and copy all the files into that folder (I am guessing this is the case). I would copy the files outside of Dreamweaver. You could do this without touching the files in the ~alpsf directory. There are a lot of variable here as I don't know exactly what you are doing.
On the file menu select window/results-select search. (this is done if the search window is not open).
Find in: Entire Current Local Site
Search: Source Code
Find: "/~alpsf/
Replace:"/
That should do it, but this is a very tricky thing. I wouldn't have a problem doing this as long as I have everything backed up.
Jim
Edited:You might have to go into your css, spry files and any others that has links to do the same (this time only select Find in: Current document once the document is open). Once that is done, delete the whole remote site and upload the changes once you check that everything is completed. -
Connectivity setup issue within DW using both Testing & Remote Servers
Hi
I have a problem with being able to connect to both my remote server and my testing server when both connections are setup at the same time.
Basically I set up the 2 x connections in DW MySQL DB Connect:
1 x dreamsin_localhost
1 x Banbury01_localhost
The dreamsin_localhost has always been the connection which goes to the remote server for nearly a year now. In my Site Manager set up it goes to www.dreamsingaporeproperty.com/public_html.
The Banbury01_localhost I just set up to go to the new testing server on my pc. Currently it has a different username and password to the remote server. Both go to localhost.
I successfully set up the testing server and added the server into the Site Manager. When I clicked 'Live View' or F12 the pages showed in my http://localhost URL.
However when I then tried to connect to the dreamsin_localhost connection it then failed with the above error:
MySQL Error#: 1045
Access denied for user 'dreamsin'@'localhost' (using password: YES)
If I take out the local server setup from the Site Manager and remove /public_html/ from the web URL the connection to the remote site then works, but the connection to the Banbury01_localhost then gets the above error message. If I keep the set up as I always had it with the URL www.dreamsingaporeproperty.com/public_html/ - then another error message about _mmServerScripts.
I'm clearly missing a piece in the whole set up but no idea what.
It seems I can't have both servers working so far.
I have a few ideas of what to do/try and will, but it is more like 'trial & error' approach rather than a proper understanding so would really appreciate some clarity on where I'm going wrong.
I think it might be because both hosts are called 'localhost' ?
I think it might be because I need to set up a user in the testing server mysql table with the same username and pw as for my remote server?
Any help would be great.Hi
I have a problem with being able to connect to both my remote server and my testing server when both connections are setup at the same time.
Basically I set up the 2 x connections in DW MySQL DB Connect:
1 x dreamsin_localhost
1 x Banbury01_localhost
The dreamsin_localhost has always been the connection which goes to the remote server for nearly a year now. In my Site Manager set up it goes to www.dreamsingaporeproperty.com/public_html.
The Banbury01_localhost I just set up to go to the new testing server on my pc. Currently it has a different username and password to the remote server. Both go to localhost.
I successfully set up the testing server and added the server into the Site Manager. When I clicked 'Live View' or F12 the pages showed in my http://localhost URL.
However when I then tried to connect to the dreamsin_localhost connection it then failed with the above error:
MySQL Error#: 1045
Access denied for user 'dreamsin'@'localhost' (using password: YES)
If I take out the local server setup from the Site Manager and remove /public_html/ from the web URL the connection to the remote site then works, but the connection to the Banbury01_localhost then gets the above error message. If I keep the set up as I always had it with the URL www.dreamsingaporeproperty.com/public_html/ - then another error message about _mmServerScripts.
I'm clearly missing a piece in the whole set up but no idea what.
It seems I can't have both servers working so far.
I have a few ideas of what to do/try and will, but it is more like 'trial & error' approach rather than a proper understanding so would really appreciate some clarity on where I'm going wrong.
I think it might be because both hosts are called 'localhost' ?
I think it might be because I need to set up a user in the testing server mysql table with the same username and pw as for my remote server?
Any help would be great. -
How can I make my JQuery Slider show on remote site?
Hello,
My Slider saga continues...
I "successfully" created a JQuery Slider using jCarouselLite and <a> tag thumbs, it shows up on my test(local)site but not on remote.
Unitl I refresh the browser or click on verticle nav links on the left, which doesn't result in a great user experience.
Here are my links to the page, the style and the js:
http://www.aliciaalmeidagraphicdesigner.com/Work.html
http://www.aliciaalmeidagraphicdesigner.com/style/Body.css
http://www.aliciaalmeidagraphicdesigner.com/js/functions.js
Anything in my code you see would be problomatic and preventing the slider from showing?
PS: As a side note, I'm also having issues with positioning the actual slider, but one thing at a time...
Thank you for any incoming responses and advice!
~LAYou have some errors in both your html and css. Clearing those out wouldn't hurt...
http://validator.w3.org/
http://jigsaw.w3.org/css-validator/
If it's still not working after those are cleaned up, post back and we can take a closer look. -
Remote Site FTP log-in & password won't stick.
Working on Vista Home Premium with Service Pack 1 and DW 8 (Installed from CS2 disk).
McAfee Anti-virus (not my 1st choice but PC came with it)
Site Definition Settings > Advanced > Remote Info >
FTP
log-in:
password:
Save enabled. Test verified.
Uploads work as expected.
Close DW.
Re-open DW, remote site log-in and password fields are empty.
Tried running as Administrator but makes no diff.
Wha'Sup?
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb
http://alt-web.blogspot.comI thought my CS2 disk contained the update but maybe not.
So after running the update from the link you provided, I get 3 out of 4 Site definitions to stick.
Some progress made
Thanks, John.
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb
http://alt-web.blogspot.com -
Problem in connecting to remote site
I have set up an FTP user in the remote server which works
perfectly fine when I click test connection. Now when I click the
remote view or upload a file or connect to remote server I get this
message -"Waiting for server" then I get this error message
"Connection to the remote host is lost.Click the Connect button to
reconnect". I have disabled my firewall too. This has been driving
me crazy for a long time. Any source of help would be of great
help.
Thanx in advance.What do you have in the Host directory field of your Remote
site's
definition? It sounds like you don't have the right
information here....
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"surenr" <[email protected]> wrote in
message
news:e2b9k2$eab$[email protected]..
>I tried using passive FTP in the remote dite definition.
It seems to be
>working
> but I am not able to view any of the remote site folders
or upload any
> files.
> When I click the test button I get this message:
Macromedia Dreamweaver MX
> successfully connected to your web server.
>
>
Maybe you are looking for
-
HP w2558hc 25.5-inch Vivid Color Full HD Widescreen Flat Panel Monitor Remote Does Not Do Anything
I just got the monitor and trying the new stuff out. Hit a couple issues like ... I have tried the remote came attached to the monitor ... the little one in the slot ... but it does not change the volume or anything else . Is there something else I
-
How to park the invoice using 'IDOC_INPUT_INVOIC_MRM' ....
Hi All, I am using FM 'IDOC_INPUT_INVOIC_MRM' for parking the incoming (Idoc) invoices. But FM IDOC_INPUT_INVOIC_MRM directly posts the invoices. I think is by default from SAP.(not sure) Can you Pls help me on this issue. Thanks.
-
AD schema update & trusts between forests.
I have a next structure: 1. Forest 1 - Domain 1 1. Forest 2 - Domain 2 1. Forest 3 - Domain 3 All Forests are connected by trust connection to each other. I've upgraded AD Schema version in Forest 1 - Domain 1 from 30 to 47 How it can affect to other
-
I using WIN98 and Forms 6i, when I run my forms the scroll bar is disabled on the Tab Canvas
-
Why do I not get pictures in the Today's highlights blank squares
when ever I click on a news item the picture donly appears as a gray square