Testing VIC2-2FX S and VIC2-2FXO cards
I want to setup two 2611XM routers with a
NM-HD-2VE ( 3 DSP), VIC2-2FXS, VIC2-2FXO cards.
Can I connect the FXS to the FXO ?
Do I need to have telephones with RJ11 Straight through cables connected to the ports of the VIC's.
Could you point me to somewhere where this scenario is addressed. ( Voice certification test lab diagrams...)
Thank you,
Tom
Dear Experts
This is going to be my first implimentation of the Voice network and is turning out to be a nightmare.i have reffered all the configuration mannuals , books and videos but still not able to make calls across the MPLS network.Need help urgently to solve the issue.
Here is the senario
PSTN>>>FXO(Cisco2905)>>>>>MPLS Cloud<<<<<<<(Cisco2905)FXS>>>>>>>>Phone
here is the configuration i have done
<<<<<<<<<>>>>>>>>
voice-port 0/1/0
voice-port 0/1/1
connection plar 2201
voice-port 0/1/2
voice-port 0/1/3
mgcp profile default
dial-peer voice 998 voip
destination-pattern 22..
session target ipv4:192.168.220.1
dtmf-relay cisco-rtp
dial-peer voice 100 pots
destination-pattern 9............
port 0/1/1
on
<<<<<<<<>>>>>>.
voice-port 0/0/0
cptone ID
voice-port 0/0/1
cptone ID
mgcp profile default
dial-peer voice 220 pots
destination-pattern 2201
port 0/0/0
forward-digits all
dial-peer voice 221 pots
destination-pattern 2202
port 0/0/1
forward-digits all
dial-peer voice 110 voip
destination-pattern 9T
session target ipv4:192.168.0.1
dtmf-relay cisco-rtp
=====================================
Early response is much appriciated
REGARDS
SANDEEP
Similar Messages
-
How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router
Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very muchOk
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks -
VIC2-2FXO why appears module 50!!!
HI experts,
my lab is a 2811 router , IOS 15 .0(1)XA, with switch 3550 and 2 cisco 7940 phones.
I want to simulate a call outside / inside from the IPhones via the FXO card connected to my analog line to the PSTN
sh run:
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FCZ121771Y4
2 FastEthernet interfaces
1 Virtual Private Network (VPN) Module
2 Voice FXO interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1957536K bytes of ATA CompactFlash (Read/Write)
License Info:
License UDI:
and a show diag to see if the card is OK
sh diag
I can see VIC2-2FXO card
WIC Slot 2:
2nd generation - FXO Voice daughter card (2 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21597-03
Board Revision : C0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC14373WZ6
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-2FXO
Version Identifier : V02
CLEI Code : CNUIARTAAB
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 54 5D 03
0x10: 42 43 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 34 33 37 33 57 5A 36 0
PROBLEM:
When I try to configure the card ,I did a previus command :
Router#sh voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
50/0/1 1 efxs up up on-hook idle y
50/0/2 1 efxs up up on-hook idle y
50/0/3 1 efxs up up on-hook idle y
what means the 50 ?? it can´t be the slot.. for the rest of the 2 digits 0/1, 0/2 and 0/3 I assume there is slot module/ port. And as you see into the show diag the VIC2-"FXO card is in SLOT 2 but why appears 3 ports? the card has only 2 FXO ports... . I am lost.
By the way the 2 ports on the card lighting in ambar
When I tried to configure the card , I use the help command and as you see forced me to assign 50 , later 0, and last one from 1 to 3 . Even that the command is incorrect as you see finally
Router>en
Router#conf
Router#configure t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#voice-
Router(config)#voice-po
Router(config)#voice-port
% Incomplete command.
Router(config)#voice-port ?
<50-50> Voice interface slot #
Router(config)#voice-port 50?
Router(config)#voice-port 50/?
<0-0> Voice interface SubUnit #
Router(config)#voice-port 50/0?
Router(config)#voice-port 50/0?
Router(config)#voice-port 50/0/?
<1-3> Voice interface port # within vic
Router(config)#voice-port 50/0/1
^
% Invalid input detected at '^' marker.
Router(config)#
So any help please, to clarify something, also any link or info to configure this simple lab.., in fact I know how to it ,but I can´t do it due to this info upstairs.. I am stacked.
Thanks a lot to any help
JesusHI Aman.,
sure I can , see below:
show run
Router#show run
Building configuration...
Current configuration : 3209 bytes
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
no aaa new-model
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1 10.10.10.49
ip dhcp excluded-address 10.10.10.56 10.10.10.254
ip dhcp pool voice
import all
network 10.10.10.0 255.255.255.0
dns-server 4.2.2.2
option 150 ip 10.10.10.10
default-router 10.10.10.1
lease infinite
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
license udi pid CISCO2811 sn FCZ121771Y4
username dediosj privilege 15 password 0 x
redundancy
interface FastEthernet0/0
ip address 10.10.10.10 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
tftp-server flash:CP7902080002SCCP060817A.sbin alias CP7902080002SCCP060817A.sbin
tftp-server flash:P00405000700.sbn alias P00405000700.sbn
tftp-server flash:P00405000700.bin alias P00405000700.bin
tftp-server flash:CP7912080004SCCP080108A.sbin alias CP7912080004SCCP080108A.sbin
tftp-server flash:S00105000400.sbn alias S00105000400.sbn
tftp-server flash:B015-1-0-4.SBN alias B015-1-0-4.SBN
tftp-server flash:B016-1-0-4.SBN alias B016-1-0-4.SBN
tftp-server flash:P00503010800.bin alias P00503010800.bin
tftp-server flash:P00308010200.loads alias P00308010200.loads
tftp-server flash:P00308010200.sb2 alias P00308010200.sb2
tftp-server flash:P00308010200.sbn alias P00308010200.sbn
tftp-server flash:P00308010200.bin alias P00308010200.bin
control-plane
mgcp fax t38 ecm
mgcp behavior g729-variants static-pt
gatekeeper
shutdown
telephony-service
max-ephones 10
max-dn 10
ip source-address 10.10.10.10 port 2000
system message Empresa prueba
load 7914 S00105000400
load 7902 CP7902080002SCCP060817A.SBIN
load 7910 P00405000700
load 7912 CP7912080004SCCP080108A.SBIN
load 7935 P00503010800
load 7960-7940 P00308010200
time-format 24
date-format dd-mm-yy
max-conferences 8 gain -6
web admin system name dediosj secret 5 $1$q3Km$7WfIn8azUkr1yJgWJruS50
dn-webedit
transfer-system full-consult
directory last-name-first
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 2001
label Jesus
description 2001
name Jesus DeDios
hold-alert 30 originator
ephone-dn 2
number 2002
label Victor
description 2002
name Victor
hold-alert 30 originator
ephone-dn 3
number 2003
label 2003
description 2003
name Tony
ephone 1
no multicast-moh
device-security-mode none
mac-address 0811.968C.9148
username "dediosjes"
mtp
type CIPC
button 1:1
ephone 2
device-security-mode none
mac-address 6C88.14B4.16BC
button 1:2
ephone 3
no multicast-moh
device-security-mode none
mac-address 0811.9682.61F0
mtp
type 7940
button 1:3
line con 0
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
end
and the show diag:
Router#
Router#sh diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:03:21 ago
Onboard VPN : v2.3.3
EEPROM contents at hardware discovery:
PCB Serial Number : FOC12124QTH
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-04
Board Revision : A0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20080326
Chassis Serial Number : FCZ121771Y4
Chassis MAC Address : 001f.ca0e.ede0
MAC Address block size : 24
CLEI Code : COM7R00ARA
Product (FRU) Number : CISCO2811
Part Number : 73-10258-05
Version Identifier : V05
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 32 31 32 34 51 54 48 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30
0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 66 C6 C2 8B 46 43 5A 31 32 31 37
0x40: 37 31 59 34 C3 06 00 1F CA 0E ED E0 43 00 18 C6
0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF
WIC Slot 2:
2nd generation - FXO Voice daughter card (2 port)
Hardware Revision : 5.0
Top Assy. Part Number : 800-21597-03
Board Revision : C0
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : FOC14373WZ6
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC2-2FXO
Version Identifier : V02
CLEI Code : CNUIARTAAB
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 54 5D 03
0x10: 42 43 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31
0x20: 34 33 37 33 57 5A 36 03 00 81 00 00 00 00 04 00
0x30: CB 89 56 49 43 32 2D 32 46 58 4F 89 56 30 32 20
0x40: C6 8A 43 4E 55 49 41 52 54 41 41 42 FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Router#
any idea..? -
Hi All,
we need to install VIC2-2FXO card on Cisco 2901 router .
On cisco 2901 router, we would configure as MGCP and we do not have any BRI/PRI link on the router.
Is it possible to make the solution work or we need to configure Voice Gateway as H.323 ?
Any ideas?
Regards,
Rebecca...Here is a good link with details of config on gateway and cucm
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008009428e.shtml
Manish -
Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
I am having trouble making outgoing call or answering incoming call.
When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
For incoming call, it rings but when I pick up the call nothing happens,
Put the receiver back on hook, the phone carries on ringing. I am in UK
and just trying to set up test system with one analogue line. Any help will
be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
Thank you for your help.
hostname Test-CME
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp excluded-address 10.139.139.1 10.139.139.10
ip dhcp pool host
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
option 150 ip 10.10.10.1
ip dhcp pool data
network 10.139.139.0 255.255.255.0
default-router 10.139.139.1
dns-server 10.139.139.5
voice-card 0
no dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
header-passing
registrar server expires max 3600 min 3600
interface FastEthernet0/1
no ip address
no ip mroute-cache
duplex auto
speed auto
no shut
interface FastEthernet0/1.2
description ** Data VLAN **
encapsulation dot1Q 2
ip address 10.139.139.1 255.255.255.0
interface FastEthernet0/1.3
description ** Voice VLAN **
encapsulation dot1Q 3
ip address 10.10.10.1 255.255.255.0
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
tftp-server flash:S00104000100.sbn
tftp-server flash:TERM41.7-0-3-0S.loads
tftp-server flash:term61.default.loads
tftp-server flash:term41.default.loads
tftp-server flash:CVM41.2-0-2-26.sbn
tftp-server flash:cnu41.2-7-6-26.sbn
tftp-server flash:Jar41.2-9-2-26.sbn
tftp-server flash:term70.default.loads
tftp-server flash:term71.default.loads
tftp-server flash:cnu70.2-7-6-26.sbn
tftp-server flash:Jar70.2-9-2-26.sbn
tftp-server flash:TERM70.7-0-3-0S.loads
tftp-server flash:CVM70.2-0-2-26.sbn
control-plane
voice-port 0/3/0
connection plar opx 202
caller-id enable
dial-peer voice 1 pots
incoming called-number .
destination-pattern 9T
port 0/3/0
telephony-service
load 7914 S00104000100
load 7941 TERM41.7-0-3-0S
load 7961 TERM41.7-0-3-0S
load 7970 TERM70.7-0-3-0S
max-ephones 20
max-dn 40
ip source-address 10.10.10.1 port 2000
calling-number initiator
service phone videoCapability 1
system message MKC CME
url services http://10.10.10.1/voiceview/common/login.do
url authentication
http://10.10.10.1/voiceview/authentication/authenticate.do
time-zone 21
date-format dd-mm-yy
voicemail 600
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh music-on-hold.au
web admin system name admin secret 0 test
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
secondary-dialtone 9
create cnf-files
ephone-dn 1 dual-line
number 201
label 201
description Sarah
name Sarah
ephone-dn 2 dual-line
number 202
label 202
description Vitthal
name User2 Vitthal
ephone-dn 3 dual-line
number 203 secondary
label 203
description Neil
name User3 Neil
ephone 1
video
username "user1" password 201
mac-address 0018.18EE.947F
type 7961 addon 1 7914
button 1:1
ephone 2
video
username "user2" password 202
mac-address 0018.18BB.B973
type 7941
button 1:2
ephone 3
video
username "user3" password 203
mac-address 0018.1885.6BA2
type 7970
button 1:3Hi
Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
Thank you for your help.
Vitthal -
In my environment there is a PBX connecto VIC2-2FXO at router CISCO1751-V. I have an old PBX and when I change the card to VIC-2FXO(EOL), I have from from PBX e works fine. But if I return the new card VIC2-2FXO it doesn't work, even tone is missing. What a real difference between VIC-2FXO and VIC2-2FXO
Hi Almir,
The card is comatible with 1751-4V. The VIC2 cards are the new generation cards. Working wise they are no different. I checked the configs nd they looked kinda incomplete. Usually the FXO works with a "connection plar/trunk". Neither did I notice any voip dial-peers.
Sample config for call flow : (phone---pbx---vic2-fxo---router1--ip---router2---fxs--phone)
voice-port 2/0
cptone BR
connection plar 3000
dial-peer voice 100 voip
destination-pattern 3000
session target ipv4:p.q.r.s
dial-peer voice 1 pots
destination-pattern .T
port 2/0
The above config should be fine for inbound and outbound calls. If this doesn't work please send me the following-
1. Exact call flow eg
2. deb voice ccapi inout
3. debug vpm signal
4. debug vtsp events
5. debug vtsp session
Subhrojyoti -
Difference between VIC2-2FXO and VIC-2FXO
All, kindly advice what is the difference between VIC2-2FXO and VIC-2FXO?
Also I will like to know if I can use VIC-2FXO in a 2821 Router.The difference is the normal evolution of products and technological generations.
You cannot do what you mentioned.
http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml -
I am looking to purchase a new 2811 router and need to know if this card will work. It is located in a 1751. Here is the 'show inventory'
NAME: "WIC/VIC 2", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: 2nd generation two port FXO voice interface daughtercard, VID: 5.0
From what I can tell, a VIC-2FXO will not work in the 2811; it has to be the VIC2-2FXO. So which card is this?
Thanks,
-Matt
EDIT: I answered my own question with a 'show diag' which lists the FRU as VIC2-2FXO. Hopefully this might help someone else out.VIC2-2FXO
Two-port VIC ? FXO (Universal). Also supports Centralized Automatic Message Accounting (CAMA) with software configuration
http://cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml -
VIC2-2FXO picks up then hangs up
Hi, I am having issues. All my VIC2-2FXO and VIC2-4FXO are picking up, then hanging up right away. I tried them on 1760s and 2811s. I tried a combination of supervisory disconnect, but can't get it to work. On 1760s, if I put a VIC-2FXO in the place of the VIC2-2FXO it works just fine. Is there a special command needed for VIC2s???
no logging console was set DOH...
here's debug's
May 20 15:55:22.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
May 20 15:55:22.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
May 20 15:55:22.892 EDT: htsp_timer_stop
May 20 15:55:22.996 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:22.996 EDT: htsp_call_bridged invoked
May 20 15:55:22.996 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:23.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
May 20 15:55:23.144 EDT: htsp_timer2 - 350 msec
May 20 15:55:23.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
May 20 15:55:23.496 EDT: htsp_timer_stop
May 20 15:55:23.496 EDT: htsp_timer_stop2
May 20 15:55:23.496 EDT: htsp_timer_stop3
May 20 15:55:23.876 EDT: htsp_timer_stop3
May 20 15:55:23.896 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
May 20 15:55:23.896 EDT: htsp_timer_stop
May 20 15:55:23.896 EDT: htsp_timer_stop2
May 20 15:55:23.896 EDT: htsp_timer_stop3
May 20 15:55:23.896 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
May 20 15:55:23.896 EDT: htsp_timer - 2000 msec
May 20 15:55:25.896 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
May 20 15:55:25.896 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
May 20 15:55:26.744 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
May 20 15:55:26.744 EDT: htsp_timer - 125 msec
May 20 15:55:26.872 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
May 20 15:55:26.872 EDT: htsp_timer - 10000 msec
May 20 15:55:28.888 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
May 20 15:55:28.888 EDT: fxols_ringing_not
May 20 15:55:28.888 EDT: htsp_timer_stop
May 20 15:55:28.888 EDT: htsp_timer_stop3 htsp_setup_ind
May 20 15:55:28.888 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55 orig called=
May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
May 20 15:55:28.892 EDT: fxols_wait_setup_ack:
May 20 15:55:28.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
May 20 15:55:28.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
May 20 15:55:28.892 EDT: htsp_timer_stop
May 20 15:55:28.964 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:28.964 EDT: htsp_call_bridged invoked
May 20 15:55:28.964 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:29.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
May 20 15:55:29.144 EDT: htsp_timer2 - 350 msec
May 20 15:55:29.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
May 20 15:55:29.496 EDT: htsp_timer_stop
May 20 15:55:29.496 EDT: htsp_timer_stop2
May 20 15:55:29.496 EDT: htsp_timer_stop3
May 20 15:55:29.560 EDT: htsp_timer_stop3
May 20 15:55:29.576 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
May 20 15:55:29.576 EDT: htsp_timer_stop
May 20 15:55:29.576 EDT: htsp_timer_stop2
May 20 15:55:29.576 EDT: htsp_timer_stop3
May 20 15:55:29.576 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
May 20 15:55:29.576 EDT: htsp_timer - 2000 msec
May 20 15:55:31.576 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
May 20 15:55:31.576 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
May 20 15:55:32.744 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
May 20 15:55:32.744 EDT: htsp_timer - 125 msec
May 20 15:55:32.872 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
May 20 15:55:32.872 EDT: htsp_timer - 10000 msec
May 20 15:55:34.888 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
May 20 15:55:34.888 EDT: fxols_ringing_not
May 20 15:55:34.888 EDT: htsp_timer_stop
May 20 15:55:34.888 EDT: htsp_timer_stop3 htsp_setup_ind
May 20 15:55:34.888 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55 orig called=
May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
May 20 15:55:34.892 EDT: fxols_wait_setup_ack:
May 20 15:55:34.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
May 20 15:55:34.892 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
May 20 15:55:34.892 EDT: htsp_timer_stop
May 20 15:55:34.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:34.932 EDT: htsp_call_bridged invoked
May 20 15:55:34.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:35.144 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
May 20 15:55:35.144 EDT: htsp_timer2 - 350 msec
May 20 15:55:35.496 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
May 20 15:55:35.496 EDT: htsp_timer_stop
May 20 15:55:35.496 EDT: htsp_timer_stop2
May 20 15:55:35.496 EDT: htsp_timer_stop3
May 20 15:55:35.560 EDT: htsp_timer_stop3
May 20 15:55:35.576 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
May 20 15:55:35.576 EDT: htsp_timer_stop
May 20 15:55:35.576 EDT: htsp_timer_stop2
May 20 15:55:35.576 EDT: htsp_timer_stop3
May 20 15:55:35.576 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
May 20 15:55:35.576 EDT: htsp_timer - 2000 msec
May 20 15:55:37.576 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
May 20 15:55:37.576 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
May 20 15:55:38.748 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
May 20 15:55:38.748 EDT: htsp_timer - 125 msec
May 20 15:55:38.876 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
May 20 15:55:38.876 EDT: htsp_timer - 10000 msec
May 20 15:55:40.892 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
May 20 15:55:40.892 EDT: fxols_ringing_not
May 20 15:55:40.892 EDT: htsp_timer_stop
May 20 15:55:40.892 EDT: htsp_timer_stop3 htsp_setup_ind
May 20 15:55:40.892 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55 orig called=
May 20 15:55:40.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
May 20 15:55:40.892 EDT: fxols_wait_setup_ack:
May 20 15:55:40.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
May 20 15:55:40.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
May 20 15:55:40.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
May 20 15:55:40.896 EDT: htsp_timer_stop
May 20 15:55:40.932 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:40.936 EDT: htsp_call_bridged invoked
May 20 15:55:40.936 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:41.148 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
May 20 15:55:41.148 EDT: htsp_timer2 - 350 msec
May 20 15:55:41.500 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
May 20 15:55:41.500 EDT: htsp_timer_stop
May 20 15:55:41.500 EDT: htsp_timer_stop2
May 20 15:55:41.500 EDT: htsp_timer_stop3
May 20 15:55:41.564 EDT: htsp_timer_stop3
May 20 15:55:41.580 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
May 20 15:55:41.580 EDT: htsp_timer_stop
May 20 15:55:41.580 EDT: htsp_timer_stop2
May 20 15:55:41.580 EDT: htsp_timer_stop3
May 20 15:55:41.580 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
May 20 15:55:41.580 EDT: htsp_timer - 2000 msec
May 20 15:55:43.580 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
May 20 15:55:43.580 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100]
May 20 15:55:44.748 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0000]fxols_onhook_ringing
May 20 15:55:44.748 EDT: htsp_timer - 125 msec
May 20 15:55:44.876 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_RING_MIN, E_HTSP_EVENT_TIMER]fxols_wait_ring_min_timer
May 20 15:55:44.876 EDT: htsp_timer - 10000 msec
May 20 15:55:46.892 EDT: htsp_process_event: [0/1/0, FXOLS_RINGING, E_DSP_SIG_0100]
May 20 15:55:46.892 EDT: fxols_ringing_not
May 20 15:55:46.892 EDT: htsp_timer_stop
May 20 15:55:46.892 EDT: htsp_timer_stop3 htsp_setup_ind
May 20 15:55:46.892 EDT: [0/1/0] get_local_station_id calling num= calling name= calling time=05/20 15:55 orig called=
May 20 15:55:46.892 EDT: htsp_process_event: [0/1/0, FXOLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]
May 20 15:55:46.892 EDT: fxols_wait_setup_ack:
May 20 15:55:46.892 EDT: [0/1/0] set signal state = 0xC timestamp = 0fxols_check_auto_call
May 20 15:55:46.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_SETUP_ACK]
May 20 15:55:46.896 EDT: htsp_process_event: [0/1/0, FXOLS_PROCEEDING, E_HTSP_CONNECT]fxols_offhook_connect
May 20 15:55:46.896 EDT: htsp_timer_stop
May 20 15:55:46.968 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:46.968 EDT: htsp_call_bridged invoked
May 20 15:55:46.972 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_VOICE_CUT_THROUGH]fxols_connect_proc_voice
May 20 15:55:47.148 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_DSP_SIG_1100]fxols_offhook_disc
May 20 15:55:47.148 EDT: htsp_timer2 - 350 msec
May 20 15:55:47.500 EDT: htsp_process_event: [0/1/0, FXOLS_CONNECT, E_HTSP_EVENT_TIMER2]fxols_disc_confirm
May 20 15:55:47.500 EDT: htsp_timer_stop
May 20 15:55:47.500 EDT: htsp_timer_stop2
May 20 15:55:47.500 EDT: htsp_timer_stop3
May 20 15:55:47.564 EDT: htsp_timer_stop3
May 20 15:55:47.580 EDT: htsp_process_event: [0/1/0, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
May 20 15:55:47.580 EDT: htsp_timer_stop
May 20 15:55:47.580 EDT: htsp_timer_stop2
May 20 15:55:47.580 EDT: htsp_timer_stop3
May 20 15:55:47.580 EDT: [0/1/0] set signal state = 0x4 timestamp = 0
May 20 15:55:47.580 EDT: htsp_timer - 2000 msec
May 20 15:55:49.228 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
May 20 15:55:49.580 EDT: htsp_process_event: [0/1/0, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
May 20 15:55:49.580 EDT: htsp_process_event: [0/1/0, FXOLS_ONHOOK, E_DSP_SIG_0100] -
To configure VOIP for this 2FXO card
We are having one Cisco 3640 Router with One Serial Port and 2FXS(2nos) Voice card. We have configured the 2FXO card to the best of our knowledge. These 2 ports are configured in EPABX. Now we are able to get the dialtone but we are unable to make calls to US . Kindly let me know the commands to configure VOIP for this 2FXO card.
Thanks in advance
Regards
Sapna shahWe are having one Cisco 3640 Router with One Serial Port and 2FXS(2nos) Voice card.We have configured voice card FXO but now due to some unknown reason we are not able to call the US office. Kindly help us .Here is the configuration:
Can u let us know what errors we have made in configuruing steps .
Here are HYD-RTR#sh voice port
Foreign Exchange Station 1/0/0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Direct line for IOC
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing Voice
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/0/1
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Connected to Alcatel PABX thru trunk line
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 1 s
Region Tone is set for US
Analog Info Follows:
Currently processing unknown
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/1/0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Second Direct Line For IOC
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing Voice
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/1/1
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Second Line Connected to Alcatel PABX thru trunk line
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing unknown
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Office 2/0/0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is plar
Connection Number is 100
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is groundStart
Number Of Rings is set to 1
Supervisory Disconnect active
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Type is pulse
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Foreign Exchange Office 2/0/1
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is groundStart
Number Of Rings is set to 1
Supervisory Disconnect active
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Please enlighten us why we are not able to make calls .IS there any fault in the configurations made by us !
Thanks in advance -
Problem with NEO2 and sata controller card
1.Product Type: MSI K8N Neo2 Platinum (MS-7025)
and the controller card is a InnoVision DM-8301 and the hard drive is a Seagate ST3320620AS
2.BIOS version: The newest one, 1C0 or something.
3.External VGA Type: Geforce 6800 GT
4.CPU Type: AMD 64 3500+
5.Memory Type: G Skill ZX 2048mb.
6.Power Supply Type:
7.Operating System: Xp Pro
8.Problem Description:
Hello. I have a strange problem with my controllercard. I wrote this text to InnoVision suport and they send me files and bios updates for a whole week and it was still the same problem. And then i tried the card in an older computer and everything worked fine.
I wrote
"Hello. I got some problems with my new controller card. I can find my new harddrive ,that's conected to the controller card, when iam inside windows and it's seems to be no problem. I can look on every seting on it and everywhere i look i can read "No problem". I Also did some test with the seatools programe and everything was fine. But when i schould copy files to it the coumputer start lagging after a few seconds and i cant do anything. After a while i can move the mouse around but the it laggs again. My computer is overclocked at the time but i have tried to use the harddrive when it's not clocked also. Also when im goin in to teh controlpanel and starts the setings for Sillicon Images sata controll and have music on my computer, the music laggs for a very very short moment. Something must be wrong and i can not find it."
It's still the same problem in my computer. The older computer had a MSI moderboard with a VIA chip and i have a nForce 3. InnoVison said i should talk to you about this problem. I have 3 harddrives but i use this controllercard because i want to have my computer overclocked and then i can't use 2 of the sata ports as i think you know.
I would be very thankful if you could help me with this problem.
//MartinI've used a noname SATA pci card (non raid) with SIL3112 on my neo2 without problems with 1C bios.
Think you may try with a disk lower than 48bitLBA need (137GB barrier), eg a 120GB disk
Quote:
have the InnoVision EIO DM-8301 and had alot of problems using it with WD 160MB SATA drive.
I am using Intel 865 based MB with 2 original SATA channels. The original SATA channels are bootable.
I could not used the EIO card with 160G HDD. The whole setup is working only after I connected oine of my 120G Segate SATA HDD to the EIO Sata card.
I think this card do not properly support HDD above 120G.
Please respond to: [email protected]
http://www.devhardware.com/forums/storage-devices-80/sata-as-boot-20080-2.html
Btw: you have xp sp2 ?
48bitLBA is not enabled in the first version.
http://www.48bitlba.com/winxp.htm
Edit:
Here's another with complete different setup and same problems
http://forum.tweakxp.com/forum/Topic212148-4-1.aspx
I doubt it has anything to do with your motherboard and/or bios.
Btw: I looked at innovision and their drivers in download area are very old.
Get the latest SIL3112 drivers for XP here:
http://www.siliconimage.com/support/supportsearchresults.aspx?pid=63&cid=3&ctid=2&osid=4&
And remember 3112 is sata150 only , so it's not sure it will work with your drive at all .
Anyway it should be set to fixed sata1.5G with jumper - not certain the controller can autonegotiate
without trouble. You cannot have command queing enabled either , disk support only NCQ and controller TCQ
so having command queing set ON will cause major conflicts in data transfers. -
M57 and any graphics cards - total lack of support - and do not buy
well just been in touch with support to find out if a new bios is coming out to support graphics cards that most people have. (HD5450 nothign over powerful) Sorry not suported in any way, only 3 crappy cards are supported officially. Basically told to sling hook Remind me not to buy IBM again from the total lack of support or updates.PCI-E standard - not if your IBM
WINNER WINNER CHICKEN DINNER!!!!!!!! I have eight (8) of the ThinkCenter M57 6072 HDU running BIOS 2RKT64AUS. I have E8400s in a couple of them @ 3.0 GHz from the stock E7200 2.66GHz. Paid $65 each of the M57s at an online goverment surplus site. The machines are used by our kids for general homework and League of Legends, Warcraft, etc. The onboard graphics would not run these games. Purchased a ASUS Radeon HD 5450 Silent 1GB DDR3 64BIT PCI-E DVI-I HDMI HDCP Passive Low Profile Video Card for about $35. ***FAILED TO POST***. Purchased a VGA GIGABYTE|GV-N640D5-1GL RTL (NewEgg or NCIX) and it installed, posted, booted, and graphically scored 7.1 on Windows Experience Index and over 1300 on Perfomance Test 8.0 from Passmark Software. Card cost $100 (not on sale) Also purchased a pair of non-matching GT630s (~$65-100) and a GT610 (~$55) to try along with the GT640 but when they all came I started with the GT640 and never looked back. RMAd the others and bought six(6) more GT640s; only six(6) because I killed one of the motherboards updating the BIOS with the E8400 installed!! Only Flash with the correct CPU in I guess. I also intalled a ASUS Xonar DG 5.1 Channel PCI Sound Card 24BIT Dolby Digital DTS 105DB SNR W/ Headphone AMP for $35 and it went in the available PCI slot and now these machines rip and scream. The slowest part of these machines is the memory and the HDD. Easy to put in a nice SSD if someone wanted. And I might experiment with the E8400 machines with some faster memory. These machines are so well built as far as the modular little cases go. Cheers all and GOOD LUCK!
-
Below is the email i sent to prometric following up my refund after cancelling an exam and being charged USD 15 for the cancellation fee, but no one is saying anything up to now or any explanation on when i should be receiving my refund.
Hi,
In regards to the above subject field and below cancellation details for an exam 070-681 -
TS: Windows 7 and Office 2010, Deploying.
I have cancelled for the exam and my visa card has been charged for the cancellation fee of USD 15, but i have
not received the refund as yet.
Please do the needful so that i can book for another exam as soon as possible.
Your urgency in this matter will be highly appreciated !
Sincerely,
Salim.
----- Forwarded Message -----
From: @prometric.com" <@prometric.com>
To:
Sent: Monday, August 25, 2014 1:08 PM
Subject: Prometric Exam Information (Z29LON501E)
Dear SALIM,
Thank you for cancelling your exam with Prometric, a leading worldwide provider of comprehensive technology-based testing and assessment services. Your cancellation request has been received and confirmed.
Included within this e-mail is your official appointment summary. Please retain this information for your records.
Included below are answers to frequently asked questions. Please do not reply to this e-mail. For additional assistance, you may visit our website at
Appointment Summary
Order Confirmation Number/Document Number: Z29LON501E
Candidate's Name:
SALIM MOHAMED
Candidate Address:
77852
NAIROBI, KE-300 00610 Kenya
Candidate Company:
Candidate Primary Phone:
Candidate Email Address:
@yahoo.com
Exam Details:
Program Name:
Microsoft (070, 071, 074, MBx)
Exam Name/Description:
TS: Windows 7 and Office 2010, Deploying
Exam Number:
070681
Exam Language:
U.S. ENGLISH
Appointment Date:
Appointment Time:
Appointment Duration (HH:MM):
4:00
Please note that the appointment duration may include an exam tutorial and client survey.
Test Site Code:
KN7H
Test Site Address:
57666,00200,1st Floor, Fedha Plaza,
MPAKA Road Junction, Westlands,
Nairobi, 00200 Kenya
Test Site Phone:
0203744720/
Payment Details:
Exam Price/Currency:
80.00 USD
Discount (if any):
0.00 USD
VAT/GST/Sales Tax:
0.00
Date of Payment/Tax Point:
24 AUG 2014
Total Amount Paid/Currency:
-80.00 USD
Payment Type:
VISA
Cancellation Fee(if any):
15.00 USD
Reschedule Fees (if any):
Payment Date
Amount Paid
Frequently Asked Questions
How will I obtain a refund?
If your credit card has already been charged and you are eligible for a refund, you will receive a refund along with a charge for any applicable fees. If a voucher was used, your same voucher number will be reactivated.
How can I Check my Appointment Status?
If you would like to review the status of your appointment, please visit. Choose "Candidate History" then login using your e-mail address and password.
What if I forget my Prometric Internet password?
If you forget your Prometric Internet password click on the following link
You will be asked to enter your e-mail address or user name, then a new password will be mailed to you at the email address you have on file with Prometric.
How do I update my candidate profile?
Please take a moment and confirm that your personal information listed above is accurate, as this is how your name will appear on any certificate earned and the address to which all certificates and communication will be sent. To ensure proper
delivery of your exam and all certification materials, Prometric must have accurate and current information. If any information needs to be updated, please visit choose "Update Personal Information", then login using your e-mail address and
password.
Please note: This address reflects your permanent, home address. To ensure delivery of official correspondence and certification material, you may also provide name and address information in your
country's official language.
Can I contact Prometric with specific questions?
If you have taken your test, plan to take a test with Prometric, or have any other concerns, please follow the appropriate links below to help solve your issues:Hello,
The TechNet Wiki Forum is a place for the TechNet Wiki Community to engage, question, organize, debate, help, influence and foster the TechNet Wiki content, platform and Community.
Please note that this forum exists to discuss TechNet Wiki as a technology/application.
As it's off-topic here, I am moving the question to the
Where is the forum for... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book:
Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C406F75746C6F6F6B2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}}) -
Tape drive and pci-x card with Solaris 10 on VMWare environment
I have a Sun X4170 server (x84_64) running VMWare ESXi 4.0. On it I have two VM guests- my production file server running Solaris 10 U7 and a test file server running Solaris 10 U9.
The X4170 has a PCI-X LSI Logic dual external U320 parallel scsi card. I have a tape drive + auto loader cabled to the X4170. It is a Quantum branded autoloader but I believe the tape drive itself is HP. The autoloader+tape drive share a single SCSI ID (6) but have separate LUNS.
I have two choices for making this system accessible to the OS:
- Virtualize the tape drive and loader individually.
- In VMWare, enable the scsi card as a pass through device. The SCSI card is then added as PCI device to the virtual machine (actually two devices since it is a dual scsi card.)
I had virtualized a single-drive tape drives with Vmware in the past.
However, when I tried I virtualize tape drive and loader, Solaris complained about the scsi id’s being invalid. I don’t think it likes two devices with a single scsi ID. Also, I think I need the backup software to see the REAL tape drive and autoloader (for inventory, changing tapes etc)
On the Solaris 10 U9 “Test” machine:
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
mpt1:scsi scsi-bus connected configured unknown
mpt1:scsi::rmt/0 tape connected configured unknown
mpt1:scsi::scsi/changer/c2t6d med-changer connected configured unknown
mpt2:scsi scsi-bus connected unconfigured unknown
cfgadm: Configuration administration not supported: Error: hotplug service is pr
obably not running, please use 'svcadm enable hotplug' to enable the service. Se
e cfgadm_shp(1M) for more details.
bash-3.00# mt status
/dev/rmt/0n: no tape loaded or drive offline
bash-3.00#
# svcadm enable hotplug
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
mpt1:scsi scsi-bus connected configured unknown
mpt1:scsi::rmt/0 tape connected configured unknown
mpt1:scsi::scsi/changer/c2t6d med-changer connected configured unknown
mpt2:scsi scsi-bus connected unconfigured unknown
pcie160 scsi/hp connected configured ok
pcie161 unknown empty unconfigured unknown
pcie162 unknown empty unconfigured unknown
On the Solaris 10 U7 “Production” machine:
The hotplug service did not exist until I installed the following patches
142934-02 SunOS 5.10_x86: failsafe patch
142910-17 SunOS 5.10_x86: kernel patch
144489-02 SunOS 5.10_x86: kernel patch
# svcadm enable hotplug
# cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c1 scsi-bus connected configured unknown
c1::dsk/c1t0d0 disk connected configured unknown
c1::scsi/direct/c1t0d0 disk connected configured unknown
c4 scsi-bus connected unconfigured unknown
c5 scsi-bus connected unconfigured unknown
pcie160 scsi/hp connected configured ok
Running “devfsadm –v “ does not change anything
Any ideas? Maybe a need to update the MPT driver or is that dangerous?
ThanksActually, updating the kernel patches (and enabling hot plug service) did solve the problem. At some point during between testing the system before and after patching, the tape drive got turned off. Since the system patching was being done remotely it was not immediately obvious that the tape drive was off.
-
Hello guys,My first time in community.my problem is that my SIM card was working ok and from today at the left of the screen up shows that is searching for the sim.I contacted the carrier and the SIM card shows that is working.Any suggestions?
Hey NicolasZen,
Thanks for the question and welcome to the Apple Support Communities. I understand that you are experiencing issues with “No Service” or “Searching” on your iPhone. The following resource provides some great troubleshooting steps that you may wish to try:
iPhone: Troubleshooting No Service
http://support.apple.com/kb/TS4429
Your iPhone may have one of these symptoms:
- iPhone displays "No Service" or "Searching" in an area of good coverage
- iPhone doesn't regain service when returning to an area of coverage
Resolution
If you encounter either of the above symptoms on your iPhone, follow these steps to attempt to resolve the issue. Test after each step.
1. Toggle airplane mode: Tap Settings > Enable Airplane Mode, wait five seconds, then turn off airplane mode.
2. Turn iPhone off and then on again.
3. Remove the SIM card and verify that it's a valid, carrier-manufactured SIM. Also verify that it isn't damaged, worn, or modified. Then reinsert it.
4. Check for a carrier-settings update. Connect to a Wi-Fi network. Then tap Settings > General > About. If an update is available, iOS will ask you if you want to install it. If Wi-Fi isn't available, connect your device to iTunes.
5. Update your iPhone to the latest version of iOS.
6. Reset network settings by tapping Settings > General > Reset > Reset Network Settings. This will reset all network settings, including Bluetooth pairing records, Wi-Fi passwords, VPN, and APN settings.
7. Restore the iPhone.
Thanks,
Matt M.
Maybe you are looking for
-
How do I make a link found in a .pdf file open in Firefox?
When I have a .pdf file open in Adobe Reader, the link opens in Google Chrome. How do I make it open in Firefox?
-
Need to display footer after displaying some item data
Hi , I have the requirement that i need to display only 15 records in a page,If more records display 15 and then need to display footer and need to go next page to display next records.Every thing is ok but how to display footer data after 15 reco
-
I bot a TV series from Appstore, erased it from iTunes as I believed it was in iCloud. I cannot find it. What do I do???
-
Maybe it's me, but this new upload...pathetic. I no longer can click and see "notifications", so that I can see if I have a missed text, or a missed call, or a tweet. Now there are a load of teeny tiny icons on the top of my phone, and I have no cl
-
Yosemite safari top sites not updating
Now that I am hooked on using Top Sites, it has stopped updating since I updated to Yosemite. Is there some setting I need to change? Sure can't find it in Pref