Tethering, yet an other question about tethering

Hi,
I used to have a jail broken iPhone and now I'm back to an "operator unlock" iPhone which is enough for me except that I can not use Internet Tethering while my mobile carrier (which is not AT&T, obvious I'm not living in the US) enables me to do so.
The option is not present event after I uploaded an modified IPCC to my phone running 3.1.3
Is there something I'm missing ?
A friend of mine bought his iPhone 3GS in South Africa (same configuration as mine) and is able to use Internet Tethering properly.
I know that iPhone OS 4 should solve this point, but would appreciate using it during the week end...
Thanks for your help.

Yes and no.
Actually I noticed that the IPCC file is different for 3.1.3 and yes if you are on an Apple partner carrier the file is going to be overwritten.
I found out a way to to it properly few hours from now and consider the point closed. The remaining question (could an Apple representative answer) is : why 2 carrier unlock iPhone bought abroad and used on the same non Apple partner carrier can have 2 different behavior regarding tethering.

Similar Messages

  • I have a Macbook Pro june 2011... I have 8GB ram but I only have 256mb VRAM... I've read some other questions about this and I realized... Why do I not have 560mb of VRAM since I have 8GB of RAM? Is there any way to get more VRAM to play games on steam?

    I have a Macbook Pro june 2011... I have 8GB ram but I only have 256mb VRAM...
    I've read some other questions about this and I realized... Why do I not have 560mb of VRAM since I have 8GB of RAM?
    Is there any way to get more VRAM to play games on steam?
    I've learned  by reading other topics that I can't upgrade my graphics card on my Macbook Pro because it's soldered into the motherboard or somthing like that, but please tell me if there is any way to get more video ram by chaning some setting or upgrading something else. I'd also like to know why I only have 256MB of VRAM when I have 8GB of RAM, since I have 8GB of RAM I thought I was supposed to have 560mb of VRAM...
    So the two questions are...
    Is there any way to upgrade my VRAM, so that I can play games on steam?
    Why do I only have 256MB VRAM when I have 8GB total RAM?
    Other Info:
    I have a quad core i7 Processor.
    My graphcics card is the AMD Radeon HD 6490M.
    I am also trying to play games on my BOOTCAMPed side of my mac, or my Windows 7 Professional side.
    THANK YOU SO MUCH IF YOU CAN REPLY,
    Dylan

    The only two items that a user can change on a MBP are the RAM and HDD (Retinas not included).  You have what the unit came with and the only way you will be able to change that is to purchase a MBP with superior graphics
    If you are very much into gaming, the I suggest A PC.  They are far superior for that type of application to a MBP.
    Ciao.

  • Verizon iPhone - mobile hotspot and other questions about the data options

    I just ordered the Verizon iPhone. Can anyone explain the options here:
    1) Unlimited corporate email & Web (business and personal email) vs. Unlimited email and web for smartphones (personal email) - what's the difference?
    2) "3G Mobile Hotspot 2GB" - does this mean that there's no way I can share my 3G connection via wifi without paying the extra $20/month?? How about tethering to a single computer (USB, BT, or WiFi) - does that also require this extra option?
    3) equipment protection - what's the difference between Extended Warranty, Asurion Wireless Phone Protection, and Total Equipment Coverage?
    thanks in advance,
    Mike

    Hi
    Regarding your #2 question; yes, you must pay $20/mo to use the 3G Hotspot aspect of the iPhone, same as with any of Verizon's phones that offer this feature such as the Droid X, HTC phones, etc. And, there is NO additional charge to tether it to your computer; it's $20/mo regardless. You can still use the iPhone's WiFi feature to search the web which is part of the regular data plan. We're only talking about paying the $20/mo for the "up to 5 devices" jumping on your phone as a hot spot.
    I'm an Apple fan, have my MacBook Pro, but my phone is a Droid X. I've been a Verizon member since a year before they became Verizon. Additionally, I am part of the Verizon & Motorola test forum; testing new software updates as they come along.
    Something you should know about Verizon's 3G Hot Spot feature; it has issues. Those of us in the Motorola & HTC forums have experienced identical issues with regard to the 3G Hot Spot feature; it disconnects every 2 minutes, even when you are actively surfing the net. Verizon & Motorola Support have been very helpful to provide what they believe are fixes, including: changing the channel, hard resets, clearing cache, etc. It does not work. Most of us believe, this is NOT a Verizon issue, but a phone maker issue.
    I also have Verizon's MiFi 2200. It costs $59/mo and is purely a hot spot device; again up to 5 devices. I use it at home, for my lap top and for those who need connectivity. It outperforms the 3G hot spot feature of the Motorola & HTC phones by leaps & bounds, and I suspect it will out perform the 3G hot spot feature on the iPhone. Additionally, you get 5GB of download with the MiFi which Verizon is planning on offering increases to 8GB & 10GB. There is NO plan to increase the 2GB download limitation on the 3G Hot spot of the iPhone & other phones, and anyone who does basic software downloads & pics, knows 2GBS is not a lot space.
    So, I would recommend not paying the $20 until this is resolved. If you do, you could pay $39 more for a total of $59/mo for the MiFi, download the software to you home computer & notebook, and end up canceling your home internet service. I did this and have saved $70/mo in my total utilities.
    One other important note: Verizon's VZManager Software for their phones & MiFi. If you did pay the $20/mo for the iPhone and decided to tether to your USB port (for power while using) and you were to use the 3G hot spot feature, it will NOT work on 64 Bit computers, regardless if you are using the WiFi feature or directly using VZManager. The MiFi has this same issue. It will only work on 32 Bit when tethered. So, you'd have to reboot your computer to 32 Bit, if you have that ability. On a Macbook Pro, simply restart holding down the "3" & "2" keys.
    I have no idea why Verizon can't simply upgrade the firmware, even recent firmware upgrades have not resolved this. Most new computers are 64 Bit now.
    Despite this, I use my MiFi 100% untethered and carry my charge cord in my bag as it also works on my Droid, and I presume they may do the same for the iPhone; reduces the need for multiple power cords.
    I really looked forward to the 3G feature of the Motorola & HTC phones, but honestly, it's just not there yet; mine was slower than Dial Up, and I'm not kidding.

  • TrackControl, Change Track, and others questions about AvTransmit

    Hi there,
    I've got multiples questions about JMF and AvTransmit, hope you will help
    For a small student project, i'm developing a streaming server using JMF, i have used the AvTransmit example.
    Streaming, etc... everything work fine, i stream music over web
    But i need help with "playlist" :
    // Get the tracks from the processor
    TrackControl[] tracks = processor.getTrackControls();
    First Question :
    The Processor use a MediaLocator to get one track, is there a way to indicate multiples tracks, such as a directory containing multiples audio file ?
    At this time, i can only set 1 file in the MediaLocator.
    I'm using a simple class as Playlist (a File[]), and, when i want to change song, i stop the thread, change the MediaLocator with another file, and restart the thread.
    It works on a Lan, but on Internet, Player (I use VLC for my test) lost the connection, i need to restart VLC to get audio again.
    Second Question
    Is there a more "elegant" way to change tracks ?
    Last Question
    I have think about building my own object Playlist... gasp...
    I've look at the javadoc... but i'm a bit lost... does my class have to implement TrackControl ? what are the object inside etc...
    If someone knows information about this...
    That's all ;)
    Thanks !
    Tommy, french student (sorry for the english)

    First Question :
    The Processor use a MediaLocator to get one track, is there a way to indicate multiples tracks, such as a directory containing multiples audio file ?
    At this time, i can only set 1 file in the MediaLocator.No. The processor uses a MediaLocator to get one file. Files (can) contain multiple tracks.
    You can, in fact, combine the tracks of multiple files together, but, there's no need to do that with your application. AVTransmit2 sends each track as a separate RTP stream, so you'd just be sticking them together just to pull them apart again.
    In general, you want to keep your architecture as one processor per file, one RTP stream per track.
    Second Question
    Is there a more "elegant" way to change tracks ?Yes. It's what I refer to as a jukebox DataSource. I discuss it / explain the concept on this previous thread.
    [http://forums.sun.com/thread.jspa?forumID=28&threadID=5400318]
    What you're essentially doing when you change the MediaLocator is starting over from scratch. You end up with a whole new DataSource, whole new Processor, whole new RTP session. On the LAN, this isn't an issue because it looks like you paused the RTP session (because the IP/PORTs don't change).
    Over the internet, though, when you stop sending and restart, you're very likely going to get a new public NAT port. And so when your stream gets to the client, it's going to look like it's from a different person than the original.
    The solution is to use the jukebox datasource to change the media without restarting the Processor or the RTP streams. That'll ensure that your stream won't move between files from the perspective of the client...
    Last Question
    I have think about building my own object Playlist... gasp...
    I've look at the javadoc... but i'm a bit lost... does my class have to implement TrackControl ? what are the object inside etc...
    If someone knows information about this...Ummmm, your "Playlist" object should just be a Jukebox datasource, so follow the link and figure out how that's supposed to work. If you have questions about it, just ask 'em here (rather than on the older thread)...

  • Question about tethering

    I have a weird question and I'm not getting a straight answer from AT&T; hoping that someone here knows. I have an iPad mini and an iPhone 5C. I have a mobile share plan through AT&T. I am wondering is it better, worse, or the same (in terms of how much data it uses) to tether the iPad to the iPhone using the mobile share wifi connection, or the LTE. I realize this is not strictly an apple question, but I'm wondering if anyone has a clue. I'm blowing through data quickly.
    Thanks

    Isn't it the same thing?  Mobile share is what they call your data plan.  You access it when you turn on your hot spot and 4G LTE service.
    If you are using the mobile data, via cellular with the phone, you are using your mobile data, or shared GB of data.
    Without the phone you can connect to your home wifi connection to get internet.   This does not use your mobile data plan.

  • Default values and other questions about MIO-PCI-16E-1

    Hi, I have a few questions involving the above mentioned board.
    First: When doing a data acquisition using an external digital trigger and an external clock, which edge of the clock signal is read by default?
    What is the delay between a STARTSCAN signal being received and a CONVERT signal being generated (signifying an ADC convertion taking place?)
    Finally, what exactly is the sample interval counter? What does it do? This is mentioned on page 4-32 in the E Series DAQ user manual.
    Hopefully these questions aren't too stupid We're designing some custom circuitry to work with the DAQ, and for things to work the timing must be precise. We need ALL the timing details about a single data acquisition t
    hat we can get.
    The system we're running on has Labview 6.0.2, and we are only acquiring data from one analog input.
    Thanks a ton!
    --Randall Cameron

    Hey Randall,
    The internal Scan Clock is a rising edge clock, if you are interested in having the rising edge clock output as high until a scan is complete, please refer here. The internal Convert Clock is always falling edge clock.
    If you are using an external signal, you can specify the polarity of the signal by selecting PFI pin, high to low, or low to high, if you are using the Clock Config VI. The method for setting the polarity changes based on the method of programming the card. And again, I do not know what the digital trigger defaults to, but you can select either polarity.
    The delay between a Scan and a Convert is based on the Convert Clock.
    Ideally, the delay is in the nanosecond range, and then the Convert Clock determines the spacing between any further samples.
    As for the sample interval counter, the following is pasted from page 4-35.
    �The sample interval counter on the PCI E Series device normally generates
    the CONVERT* signal unless you select some external source. The counter
    is started by the STARTSCAN signal and continues to count down and
    reload itself until the scan is finished. It then reloads itself in preparation for
    the next STARTSCAN pulse.�
    So just let us know if you have any questions on getting the polarity set up, or if anything is not fully explained.
    Best regards,
    Justin T.
    National Instruments

  • Other question about Automatic Resolution Gap

    Hi again.
    I 'm confuse about function of Compression of Log Archive Dest, so I have this question:
    Is Log Archive Dest Compression Atributte valid only for Resolution GAP???????
    Thanks again.

    LOG_ARCHIVE_DEST_n = '....... COMPRESSION=enable ..."
    I believe this attribute is set to enable compression *during redo gap resolution*.
    According to MOS Redo Transport Compression in a Data Guard Environment [ID 729551.1],
    In 11gR1, it is also possible to enable compression *duing redo transport service with Maximum* *Performance* using the following hidden parameter.
    _REDO_TRANSPORT_COMPRESS_ALL=TRUE
    According to OOW 2010 presentation,
    In 11gR2, redo transport compression can be enabled *with all data guard protection modes.*

  • Adobe Flash crashes and other questions about Flash

    There have been several instances of Adobe Flash crashes whether I am using Firefox, IE or Google Chrome browsers - and simply reloading the page corrects this BUT recurs again and again.
    I'm running Windows 8.1 64bit in which the Flash program apparently comes embedded in the OS as a 32/64 bit hybrid. When I inspect the Flash version add-on in Firefox, and run an update check, Adobe reports, correctly, that my system is Windows 64bit , English, Firefox. Then, when I do the same in Windows Internet Explorer by checking the embedded version, I get a message that KB2999249 is available for download to correct Flash issues in IE. Since that install, Flash hasn't crashed in IE [yet].
    So, my question is: How can I be certain that when Firefox reports that Flash is "up-to-date" that it is indeed a 64bit compatible version? Note that the Adobe download site only identifies one available version for Firefox, IE and Google - the current version being 15.0.0.152 file: NPSWF32_15_0_0_152.
    Does the "32" part of the file name suggest that it is a 32bit application and, if so, where can I find NPSWF64_15_o_o_152 [if it exists]?
    ''edited the title of this thread to reflect the questions asked''

    I now understand the version nuances between the browsers and thanks for the response. Now what, if anything, can I do to address the continuum of Flash crashes since I find it difficult to believe that I'm the only user experiencing this anomaly?

  • Family has problems viewing my page + other questions about iweb 08???

    Hello: I have been using iweb 08 since it came out and have had nothing but good things to talk about it. I ususally test my website on the library pc's or on my mac using firefox. I never see anything not working. My family and friends however always tell me about things not working and not showing up. They say it takes a long time to load - I am not sure if that is the problem overall or if it comes from them using Pc's (windowns xp mainly).
    My questions:
    1. How can I make sure that the content of my page does not take too long to load if I am using music, videos and images? (I know to look at the file sizes of all of them, but is there another trick)
    2. Can I have a main page for everyone to view my welcome page and then password protect the rest of the page only to my family? Or even make some pages only available for eg. Mom and Dad with another password?
    3. Does a Hit counter not work when publishing to my own domain? If yes, why do comments and password protection work then?
    4. Is it possible to link a page from my start page where I incorporated a picture and enable my viewers to see it larger when clicking on it without me making a new site that shows up in the top panel (just like about me, blog, photos, movies)
    5. There used to be a page to look at .mac customers and what they did with their membership. Starting their own business, military wife uses web gallery etc. I can't seem to find this page again, does anyone know the link.
    I know this is a lot, if I could I would offer a reward for all the answers I need. Thanks though for helping me out, I try to help out as much as I can myself. Thank you. Sabina

    Your site is loading OK but slow in Windows XP running IE V 7. The form is loading too. Maybe its a Vista problem?
    My general rule is that if your site locks IE then you have to reduce the page size and optimize.
    If it loads slowly and shows layout anomalies, then optimizing will usually cure it.
    I have been using Web Site Maestro for several years and can highly recommend it. Download the trial version which will optimize 50% of your files and watch the screen to see how much it reduces the individual file sizes.
    For an example of photo file reduction see....
    http://roddymckay.com/PhotoStuff/PhotoFile.html

  • One other question about hyperlinks

    I nearly forgot to ask this.
    Is it possible to hyperlink from one part of a page to another, within the same page. For example, if i talk about a style of music that I write, and lower down the page there are some examples, is it possible to write click HEREto listen, and be taken lower down the page?
    I know it can be done in HTML, but i cant see a way in iweb.
    Anyone?
    David Tobin

    Hi,
    This is called anchors. But it is pretty hard to do. Varkgirl has a tutorial here:
    http://www.varkgirl.com/Anchors/One.html
    Cyclosaurus has a different method here:
    http://geocities.com/[email protected]/anchors_1.html

  • Yet another pointless question about the practically non-existent iMac G5 Apple Hardware Test (AHT) disk.

    I have a 17" iMac G5 (iSight model) also known as model A1144, PowerMac12,1 or MA063LL/A.
    Where do I download the Apple Hardware Test (AHT) disk for this machine? Apparently nowhere. However, it would really help me on my quest if I knew what I was looking for.
    Does anyone know what AHT version is compatable with my machine? 2.2.1? 2.3.1?
    How about the part number on the disk? I have some Intel disks that say 2Z691-5734-A that (obviously) won't work.
    Is the AHT on Disk 1 or Disk 2? I'm starting to think there never was an AHT for this model.
    Where do I get those ASD disks the so called "geniuses" have?

    Disk 1: 2Z691-53179-A
    Disk 2: 2Z691-5493-A
    Compatible with eMac (2005), iBook G4 (Late 2004), iBook G4 (Mid 2005), iMac G5 17-inch (ALS), iMac G5 20-inch (ALS), iMac G5 (17-inch iSight), iMac G5 (20-inch iSight), iMac (Early 2006 17-inch), iMac (Early 2006 20-inch), Mac mini, Mac mini (Late 2005), Mac mini (Early 2006), MacBook Pro, Power Mac G5 (Early 2005), Power Mac G5 (Late 2005), PowerBook G4 (15-inch Double-Layer SD), PowerBook G4 (17-inch Double-Layer SD)
    http://www.welovemacs.com/2z69153179a.html
    AHT I think was on a seperate CD.
    Thanks Kappy, if v2.2.1 then search for...
    018-1680-A.dmg

  • Installing windows 7 and one other questions about boot camp

    I have a 20 inch iMac with Mac OS 10.5.7 and all updates. I am thinking about upgrading from vista on boot camp to Windows 7. I know what to do but i wanted to hear some personal experiences from other people. Also, a long tome ago, I tried to install Windows XP but realized half way through that I did not have a product key. It turns out I did not need one, but I tried to cancel the installation process and all I would get was "Press any key to restart" and I would be sent back to the beginnign of the installation. I was trapped in a loop. For future reference, how do u "escape" this loop? Thanks

    You 'escape' by not killing it. And most people have to redo their entire install to get things working properly.

  • My laptop won't turn on and other questions about it...

    This isn't a problem that is mostly described in imediate forum discussions. My laptop is 5 years old this summer and since day 1 I have had issues with it, especially with the over heating.... Well starting very recently, my computer has decided that whenever its doing work to stop working and freeze up which requires me to force restart it... but now it just stays at the screen.. im sure its a HD problem or something because when i go to the cmd+s screen and attempt to repair it, it says that it's unable to repair. im trying my hardest not to take it into the store. what should i do. ive been told i should just get a new laptop because the generation of mine was infested with system problems with heating up and starting up.

    Hi T,
    No easy way out of that, my friend, sorry. We have other attempts to do.
    It's spread the word that bad super blocks can be repaired with DiskWarrior (http://www.alsoft.com/DiskWarrior/index.html).
    But before you do that you can try to connect your friend's mac to yours using a firewire cable and startup your machine in target mode - I think it's done pressing T key after Power button. Once you do this use his Disk Utility to repair you HDD. Other hardly successful attempt that would be really hardly successful even if you are truly lucky for having your machine and your friend's one with the exactly same hardware configuration is carbon copying his HD in a USB external disk, if you can get to this point then connect your usb disk, press and hold OPTION and then press Power button, choose USB happy disk and cross your fingers (I am already feeling bad writing this down, it's a bit sin, all bits concatenated will be in horror) - if you get somewhere from here I must congratulate you.
    And after this nonsense the good advice is for you to buy DiskWarrior and a Snow Leopard, if you can not recover your HDD with that you'll have to take it to repair as a last resource before buying another one.
    Good luck.

  • An other question about required fields en color change

    I've got 4 fields.
    The client must enter a Country name in Field1
    If this is "NL", than Field2, Field3 and Field4 become required.
    I've done this with FormCalc
    if (Field1 == "NL") then
    Field2.validate.nullTest="error"
    Field3.validate.nullTest="error"
    Field4.validate.nullTest="error"
    else
    Field2.validate.nullTest="disabled"
    Field3.validate.nullTest="disabled"
    Field4.validate.nullTest="disabled"
    endif
    Now comes my problem:
    When field2, field3, and field4 are requered, they have to change color (fill color red) when empty
    And when they are not required, they don't have to change color
    Can anyone help me with this problem?

    Hi,
    Here is an example of script for changing the visual appearance of an object. Please note that the script in this example is JavaScript. https://acrobat.com/#d=xHziYOr8zapKWtuVhWUk0w
    Hope that helps,
    Niall

  • How, where, and other questions about BC 2.1

    I was in MacOS 10.5.2 and ran software update. It did not tell me of the "new" Bootcamp 2.1 that will make SP3 work on the intel-Mac. So I started up in XP mode and ran Apple Software update, still no mention of the 2.1 update. So then I went to the Apple download page and downloaded the 2.1 update. It is an .exe file. I clicked "RUN" and nothing happened while in XP mode. So what is it. Did it not work for me, or do I not need it because I already had it?
    Apple //GS

    OK that explains why boot camp 2.1 didn't load. It needs Boot Camp 2.0 to pre-exist before it installs.
    You probably installed/upgraded to Leopard on the Mac side however did not update your boot camp drivers on your Windows side. First, you will need to upgrade your 1.4 (beta drivers). Just BOOT IN WINDOWS and insert your Leopard Installation disk in the drive. This should automatically begin to install all the Boot Camp 2.0 drivers.
    Once that is completed then you can run Apple Software Update and it will install the boot camp 2.1 drivers.
    Axel F.

Maybe you are looking for