Text mode and Binary mode

Can anybody give the differences between Text and Binary modes that are used with Datasets??

For Binary Mode
The contents of the file are not structured in lines in the READ DATASET or TRANSFER operations. Instead, they are input or output as a stream. You do not have to specify the IN BINARY MODE addition explicitly.
For Text Mode
If you use this addition, the contents of the file are structured in lines. Each time you use the READ DATASET or TRANSFER statement, the system reads or writes a single line. If the data object to which you are transferring the data is too big, it is padded with spaces. If it is too small, the data record is truncated.
Hope this helps.
ashish

Similar Messages

What is difference between TEXT mode and BINARY mode?

Hi,
          What is difference between TEXT mode and BINARY mode? In TEXT mode what is "ENCODING DEFAULT".
OPEN DATASET wl_filename FOR INPUT
                          IN TEXT MODE ENCODING DEFAULT.
OPEN DATASET wl_filename FOR INPUT
                          IN BINARY MODE .

Hi vishnu,
1. files like .TXT files are considered to be text,
   and other files like .EXE . DOC etc are binary files.
2. In text files, after each line, there are two
   internal binary characters
one for line feed and another one for newline.
3. But, we don't have any meaning for it,
   when we view such files in notepad, for eg.
   Hence, to only get the understandable content,
   we should open such TXT files, in text mode.
(we can also open them in binary mode,
but we will get two extra characters after each line,
   and such two extra characters are meaningless
for interpreting the text)
4. In binary mode, each byte by byte is considered,
   without any meaning.
regards,
amit m.

Open data set from Text mode to Binary mode

Hello All,
In a program i am using the command
    OPEN DATASET file FOR OUTPUT IN TEXT MODE
    ENCODING NON-UNICODE IGNORING CONVERSION ERRORS.
Now i want to change this open data set to binary mode. I mean to change the command like below.
OPEN DATASET file FOR OUTPUT IN BINARY MODE.
when i do this. the output in the file is totally changing. I mean previously i have some text now i have some diffrent characters.
How can i use this command with out change in the output as previous output. Please tell me the changes and why i have to do.
OPEN DATASET file FOR OUTPUT IN BINARY MODE.
Regards,
Lisa.
Message was edited by:
        Lisa Roy

Text Mode means that the records in the file have a carriage return marking the end of each record.
Binary Mode means the file is a string of data.
You can't read a text file in BINARY MODE, or a binary file in TEXT MODE.
If you are changing the mode, then you must be supplied with a file in the new mode.

UI Control options do not appear for TCD mode and Webdynpro mode

Hi guys,
When I open the screen Start option in eCATT for ECC 7.0, there is no options for TCD mode and Webdynpro mode, only have for SAPGUI mode. So pls help to me find the options for these modes.
Thanks in advance,
Thien

Hello Friend,
This has been corrected by 640 SAPKB64023 and 700 SAPKB70016.
Please install the relevant SP to your system.
Thanks.
Eric Monteiro

Iphone in recovery mode and DFU mode but PC still doesn't recognize device

HELP! My iphone 4 just keeps blinking the apple logo for hours! I tried the recovery mode and DFU mode, the first time went well, but it started to blink again after I restored it. Now I'm doing the same steps going to recovery mode and DFU mode, they work on the phone but for some reason, my laptop doesn't recognize any device connected. I tried everything on the internet and still wont work. WHAT CAN I DO???
by the way, Mine is windows 7.

it needs repair
Peace, Clyde

Region Monitoring iOS 7 : didEnterRegion method is not calling when app is killed by user or by OS in iOS 7 only. It is working fine when it is in background. and the same code is working fine with iOS 6 for both app in suspended mode and background mode.

Region Monitoring iOS 7 : didEnterRegion method is not calling when app is killed by user or by OS in iOS 7 only. It is working fine when it is in background. and the same code is working fine with iOS 6 for both app in suspended mode and background mode. What changes I have to made to work great in iOS 7 also.

I rewrote code for debugging purpose and tried to catch error using GetLastError();  method,
but it only printed 0. Below is code snippet; I think Create() throw an exception
and code goes to catch block.
LONG ConnectTS(CString strIP, UINT n_Port)
try{
          ErrorLog(0,0,"ConnectTS is calling Create [is going to call]","");
          if(!Create())
// Exception Line
n_Err = GetLastError();
return NET_INIT;
catch(...)
                   DWORD errorCode = GetLastError();
                   CString errorMessage
                   errorMessage.Format("%lu",errorCode);
                   ErrorLog (0, 0, "Image
System", (LPTSTR)(LPCTSTR)errorMessage);
                   return  IS_ERR_WINDOWS;
Output: -
ConnectTS is calling Create [is going to call]
Image System
0

Lightroom print mode and Color mode grayed out

Both print mode and color mode selections are grayed out not allowing me to select them. Help

I see you haven't gotten much input so far from the Mac experts...
As a Windows user without an Epson printer myself, I can't comment on why you might have color problems under the covers where the software doesn't seem to be following the chosen settings. However, perhaps I can get you thinking about how to further diagnose the problem...
The obvious thing I see is that you've chosen "Photoshop Manages Colors" in the main dialog, which implies your intent is to shut off color-management in the printer driver itself. So to me the graying out of those settings in this case seems to make sense.
Have you tried a test print using the "Printer Manages Colors" setting?
Also, to try to test whether color-management isn't being turned off in the printer (regardless of what the grayed-out settings show), do you see any improvement if you use "Photoshop Manages Colors" but choose a standard profile, such as sRGB IEC61966-2.1 for the Printer Profile setting?
-Noel

Page mode and pdf mode views are different?

Hi,
I am using BO XI R2.
I have a report. When I view the report in page mode its showing the number of pages as 4.
But when I view the report in pdf mode its showing only in 1 page.
How can we make the report view same in both pdf mode and page mode?
Are there any seetings need to be done?
Thank you,
Regards,
Gowtham.

''afew2 [[#question-1054433|said]]''
<blockquote>
I refreshed FF 36.0.4 on invite. Since then "save page as " and "save image as" are not working -- no response when clicked.
In Safe Mode, same problem.
I serached past forum discussions and found several occurrences, but no convincing response.
</blockquote>
I tried troubleshooting plugins, none appeared to be causing the problem.
I installed 36.0.1, but no difference. Went back to 36.0.4, still no change.
I ran a malware check with Malwarebytes, no change.
A past thread here suggested deleting localstore.rdf, which I tried, no result.
People have had this problem in the past. No one has any idea of how to fix it?

Using both power saving mode and offline mode caus...

So I am having a very strange problem. I have been using the Situations App (formerly Nokia Situations) to automatically put my phone into offline mode, and power saving mode over night. 9pm to 6:30am.
Recently the phone as started refusing to leave the offline mode in the morning. Even if I try to change the profile manually it says "Unable to change profile". The only way I can get out of offline mode is to reboot.
I uninstalled Situations, and manually put the phone into offline mode and power saving mode. By the morning I had the same issue, stuck in offline mode until reboot. So it's not the App causing the problem. I've tried a soft reset, same problem still.
I also noticed that over-night (from fully charged before 9pm) to 6:30am I used about 70% of my charge. (A combination of power saving mode and offline mode is killing my battery!)
I would have to go to work and immediately put my phone on charge! I.e.. 12 hours of offline + power save has drained my battery almost completely.
Last night I decided to use the Situations App to put the phone into offline mode, BUT NOT activate power save mode.
This morning the phone had virtually full charge and it had no problem returning to online mode. So it's ONLY if I use BOTH power-save and offline. (Tonight I will try using power-saving mode and NOT offline mode to see if it's only the power-saving mode causing the issue!)
If I manually enter offline+power-save mode, and then try to return to on-line/non-power-save mode, relatively quickly, i.e.. Not over-night, everything is fine. It's only over night the problems start!
Any help?
Rob
PS. I also have the problem where using HSPA+ causes my phone to drop from the network and stop being able to receive/make phone calls. But disabling HSPA+ works around this for now, I think this problem is unrelated however.

I have a similar problem. My 808 PureView loses 70% of its charge overnight if I leave it in normal profile without power-saving. To deal with this issue, I started using the situations app to put the phone in power saving mode overnight. That solved the problem (although I never put my phone to offline mode). This is a weird problem because throughout the day my phone doesn't use 70% of charge, but it does overnight while doing nothing!
I have also experienced the second problem, losing cellular and internet connection, on my 808. I have started a thread to deal with this issue.
http://discussions.nokia.com/t5/Nseries-and-Symbian-Smartphones/Nokia-808-PureView-loses-cellular-an...
I believe it is a firmware bug that causes this problem.

My MacBook pro will not startup. I get a blank grey screen no logo appears so I can't chooseadiffer t drive nor boot from DVD. Safe mode and verbose mode also don't change blank screen.

It was running slow with the colored spining appearing often. This started happening weeks ago with Yosemite so I formatted the disk with the DVDs that came with the mid 2011 MacBook pro, 10.6.8. I then installed Yosemite on an external drive and this morning i was booted from the external hd with Yosemite and it stopped recognizong mouse clicks so I forced a restart and now I'm stuck with the blank grey screen. Safe mode and verbose mode also do not work.

Lao Bo,
yes, you can locate and copy a file from your HD to a USB key using UNIX commands. If you know the exact name of the file which you’re trying to locate, try this:
find / -iname filename -print
This command will search your entire internal disk for the particular filename. If you know that it’s within a particular user account, then you can save search time with this variation:
find /Users/username -iname filename -print
Either variation of this command will print all files found which have the given filename. Presuming that you’re able to identify the correct file, you can copy it to a USB key using the command
cp -p filename_returned_by_find /Volumes/USB_volume
If you’re not sure which volume name your USB key has, this command will show you what the possibilities are:
ls /Volumes
Please let me know if you have any trouble with these commands.

CSM route mode and bridge mode can exist at the same time?

I'm using CSM on ver 4.x,and I used to the bridge mode for firewall load balance,for a new requset,I have to create a new server/client vlan,but the original firewall load balance was effected when I issued the server vlan command,and I'd like to use route mode for the new server farm,I'm wondering that route mode and brige mode can't exist at the same time,because it seems it doesn't make sense.Any reply will be very appreciated.

you can use bridge mode and route mode at the same time.
Traffic with desintation mac address being the CSM will be routed, otherwise it will be bridged.
Gilles.

Timeline window missing button to switch between frame mode and timeline mode

I'm using Photoshop CS6 Extended.
This is what my timeline looks like now.
In tutorials they refer to a button that should be to the left of the drop menu that says "forever". The button is supposed to allow you to switch between frame mode and timeline mode.
this is what the timeline window looks like in timeline mode and with the button that allows you to switch.
I've already tried reinstalling and upgrading to CS6 extended, as some forums suggested.
Please help. Animation is the core reason that I need photoshop and without this button I'm extremely limited. Thanks.

OK. This should work. Copy and past the below script into Script Editor, save it as an AppleScript application to the Desktop. Double-click it and it should change to grayscale. Double-click it again and it'll toggle back.
tell application "System Preferences" to activate
delay 1
tell application "System Events"
tell process "System Preferences"
click the menu item "Universal Access" of the menu "View" of menu bar 1
click the radio button "Seeing" of the first tab group of window "Universal Access"
click the checkbox "Use grayscale" of tab group 1 of window "Universal Access"
end tell
end tell
tell application "System Preferences" to activate
delay 1
tell application "System Events"
tell process "System Preferences"
click the menu item "Universal Access" of the menu "View" of menu bar 1
click the radio button "Seeing" of the first tab group of window "Universal Access"
click the checkbox "Use grayscale" of tab group 1 of window "Universal Access"
end tell
end tell
tell application "System Preferences" to quit

Can someone explain what recovery mode and dfu mode are?

title says it all.

The main difference between DFU mode and Recovery mode is the iBoot bootloader. iBoot tells the iPhone/iPod touch/iPad what to do when it turns on, eg. load up iOS version whatever (for me, still 4.2.6 on my Verizon iPhone). When you upgrade your device's firmware, it goes into recovery mode.That way, iBoot can make sure you're flashing into a firmware that's equal to or greater than the current version of firmware you have installed. When you enter DFU mode, there isn't this limitation, so you can flash any version of iPhone OS/iOS that you want, provided the device is compatible with it and Apple is still signing for it.
If this answered your question, tell me. If it didn't, well, tell me and I'll add more!
Hope I helped!
--CS

Bridge mode and router mode

hello,
I want to understand the basic operation, difference and advantages of both Bridge Mode and Router mode?
i also want to know in which case i should go for Bridge mode and Router mode?
regards
Devang

It realy depends on your requirements.
Mainly bridge mode is used for multicast support, Multiple DMZs + FWSM, server initiated connections or for seemless migration from previously installed "bridged load balancing environment".
Some of the differences are
In bridge mode you do not need additional config for "Direct server access" / "Server Initiated connections"
Broadcasts are dropped in routed mode whereas they are bridged in bridge mode.
LB functionality is same in both modes.
Syed Iftekhar Ahmed

How to print Individual mode and Collective Mode for Goods Receipt

Hi Friends,
Right now I am working on Smartforms on MIGO transaction.
My Client requirement is that all items that have been received should be printed on one form in
Collective mode.More specifically in the transaction MIGO only the items checked OK should print on
the form. It Should also allow the user to print Items in Individul mode.
Could anybody please specify on what basis( fileds ), I will be able to segregate the items.
how can I write the select stament so that when the user selects collective mode and accordingly
should print. same for individual mode.
Kindly help me.
Regards,
Xavier.P

In MIGO tcode you strcture like GOHEAD-XNAPR and GOHEAD-WEVER
if you check GOHEAD-XNAPR = X and select GOHEAD-WEVER Individual mode and Collective mode.....

Text mode and Binary mode

Similar Messages

Maybe you are looking for