TFTP Proxy and duplicate device names

With the TFTP Proxy feature added in CUCM 8.6(2), has anyone figured out what happens if the same device is configured on two different clusters?  Pre-8.6, CUCM had an ordered list of Alternate Cisco File Locations, so the first cluster on the list that had that device would serve the .cnf file.  But TFTP Proxy doesn'ty have an ordered list, so which cluster has priority?
Chris

I saw that document and read it before I posted.  And I poured over it again to make sure that I had not missed anything.  That document makes no reference to the same MAC address configured on two clusters.  It does refer to common files, like ringtone.xml, being served by the first server if it has that file.
Here the most relevant part:
Proxy TFTP polls all the clusters that it controls for the requested file, starting from its own database.
The cluster where the endpoint is configured returns the file.
The locale and ring list file requests do not contain a MAC address, so Proxy TFTP returns its own copies of these files.
However, because this is a cache, I assume the TFTP Proxy server caches a copy of the file (actually, if it does, how does it manage changes to the .cnf file?  Does it version check?)

Similar Messages

  • DCR Add Device shows Duplicate Device Name

    When manually adding some devices via DCR Device Management I get the "Duplicate Device Name" error.
    The names do not show in the DCR Device Management Selector. I have also done an Export of All Devices and the names are not in there either.
    I have confirmed that the forward and reverse names and IP addresses resolve corerctly in DNS.
    How/why would it complain of a duplicate name that doesn't seem to be in there?
    This is LMS v3.2  CS v3.3.0
    Thanks for any help,

    The devices are as you suspect in the "Devices not configured in ACS report"
    I think I see what's happenned. Looks like the devices were orginally added to LMS but at the time they were not correctly configured in ACS.
    What has happened since is that the ACS configuration is now correct, but the devices have also been deleted from the LMS DCR.
    So they are not showing in the DCR but they are showing in the "Devices not configured in ACS report".
    I presume this is what is preventing them from being re-added, will they naturally age out of the ACS report somehow?

  • ISCSI and Solaris device names ..... target binding settings

    Hi,
    I configured an iSCSI environment with Sparc Solaris 10 U4 software inititator and EMC CLARiiON CX3-10c.
    So far it is working, but I`m wondering about the Solaris device names /dev/rdsk/c5t3d0. I disabled MPxIO
    in /kernel/drv/iscsi.conf. I have 32 LUN configured in CX3-10c target. The Host LUNs are 0 ...31, but Solaris
    created device nodes started with target 3, e.g. c5t3d0s2 (see output from iscsiadm list target).
    # iscsiadm list target -S iqn.1992-04.com.emc:cx.hk193001030.a1
    Target: iqn.1992-04.com.emc:cx.hk193001030.a1
    Alias: 1030.a1
    TPGT: 2
    ISID: 4000002a0000
    Connections: 1
    LUN: 31
    Vendor: DGC
    Product: RAID 10
    OS Device Name: */dev/rdsk/c5t34d0s2*
    LUN: 30
    Vendor: DGC
    Product: RAID 10
    OS Device Name: */dev/rdsk/c5t33d0s2*
    LUN: 1
    Vendor: DGC
    Product: RAID 5
    OS Device Name: */dev/rdsk/c5t4d0s2*
    LUN: 0
    Vendor: DGC
    Product: RAID 5
    OS Device Name: */dev/rdsk/c5t3d0s2*
    Why are the device node names stared with target 3 instead of target 0 ????
    Thanks for your help !!!
    Edited by: test111 on Mar 25, 2008 8:36 AM

    Hi,
    I configured an iSCSI environment with Sparc Solaris 10 U4 software inititator and EMC CLARiiON CX3-10c.
    So far it is working, but I`m wondering about the Solaris device names /dev/rdsk/c5t3d0. I disabled MPxIO
    in /kernel/drv/iscsi.conf. I have 32 LUN configured in CX3-10c target. The Host LUNs are 0 ...31, but Solaris
    created device nodes started with target 3, e.g. c5t3d0s2 (see output from iscsiadm list target).
    # iscsiadm list target -S iqn.1992-04.com.emc:cx.hk193001030.a1
    Target: iqn.1992-04.com.emc:cx.hk193001030.a1
    Alias: 1030.a1
    TPGT: 2
    ISID: 4000002a0000
    Connections: 1
    LUN: 31
    Vendor: DGC
    Product: RAID 10
    OS Device Name: */dev/rdsk/c5t34d0s2*
    LUN: 30
    Vendor: DGC
    Product: RAID 10
    OS Device Name: */dev/rdsk/c5t33d0s2*
    LUN: 1
    Vendor: DGC
    Product: RAID 5
    OS Device Name: */dev/rdsk/c5t4d0s2*
    LUN: 0
    Vendor: DGC
    Product: RAID 5
    OS Device Name: */dev/rdsk/c5t3d0s2*
    Why are the device node names stared with target 3 instead of target 0 ????
    Thanks for your help !!!
    Edited by: test111 on Mar 25, 2008 8:36 AM

  • IOS 8.1 Mesages/Text Message Forwarding - Duplicate Computer names

    I just upgraded to iOS 8.1 on my iPhone 6.  On my IPhone, when enabling Text Message Forwarding to my devices I noticed that my Mac's (15" MacBook Pro 5.1 Late 2008 with Yosemite) computer name appeared there twice. As expected, only one of the two duplicate computer names was successfully activated (switched to green) for text message forwarding,
    I had recently changed/edited the Computer Name of my Mac in System Preferences/Sharing panel.  The duplicate names that appear in Text Message Forwarding is the previous/old name and the existing name of my Mac described above.
    Is there a way to delete the old name from appearing in Text Message Forwarding by changing something on my Mac, such as editing or deleting a plist?
    Thanks in advance for any constructive assistance, comments or suggestions that can help me fix this.

    Problem solved! 
    I changed my iCloud password and the duplicate device names (ghost devices) disappeared from Settings/Messages/Text Message Forwarding on my iPhone.
    I hope this helps somebody with a similar issue.

  • Duplicate Devices In LMS 3.2

    Hi There.
    I have trolled this forum, and I find issues with LMS 3.1 and Duplicate devices and the engineers say that it is fixed in LMS 3.2, but I have a customer who is experiencing this with LMS 3.2 below is the customers request:
    This has now been the 3rd week in a row that after the XXXXX discovery we
    ended up with duplications.
    I have looked at a few and most are due to 2 or more ip addrs defined on te
    device.
    The example here are the RCC MSFCs which we manage via VLAN50 ip and the source
    is set to VLAN50 on the device but LMS also discovers it via a loopback addr.
    It is causing us hassles with max limit on LMS system as well as having
    duplications on reports.
    Please could you give me some advice.
    Joan

    Ok ran the walk, and it can be read by one of the devices showing up as a duplicate, below is a short extract, should you require the whole walk, ill be happy to post it
    The following is a SNMP walk of device 10.111.1.2 starting from .1.3.6.1.2.1.4.20
    SNMP Walk Output
    .1.3.6.1.2.1.4.20
    RFC1213-MIB::ipAdEntAddr.10.10.10.10 = IpAddress: 10.10.10.10
    RFC1213-MIB::ipAdEntAddr.10.111.0.0 = IpAddress: 10.111.0.0
    RFC1213-MIB::ipAdEntAddr.10.111.0.4 = IpAddress: 10.111.0.4
    RFC1213-MIB::ipAdEntAddr.10.111.0.16 = IpAddress: 10.111.0.16
    RFC1213-MIB::ipAdEntAddr.10.111.0.75 = IpAddress: 10.111.0.75

  • When I try to sync my ipod it says it cannot be synced because "a duplicate file name was specified". What does that mean and how can I fix it??

    When I try to sync my ipod it says it cannot be synced because "a duplicate file name was specified". What does that mean and how can I fix it??

    I'd start with the following document with that one:
    iPhone, iPad, iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows

  • When synching my ipod 80 gig classic, I get this message " iPod cannot be synched.  A duplicate file name was specified"  And yet, any new music in iTunes is added.  What causes this message?

    When synching my ipod 80 gig classic, I get this message " iPod cannot be synched.  A duplicate file name was specified"  And yet, any new music in iTunes is added.  What causes this message?

    Try deleting the iPod Photo Cache from the nominated folder that you have set up to sync photos to the devices.
    See iTunes: Understanding the iPod Photo Cache folder for more info.
    tt2

  • Attempting 1st time sync and software duplicates first name as middle name

    I am attempting my 1st sync between my Blackberry Pearl 8130 device and my Microsoft Outlook.  When I do this the software is automatically duplicating the first name of many of my contacts and then proceeding to add the same first name to the middle name as well.  Is there a way for me to synchronize my Blackberry device without adding these incorrect duplicate middle names?  If not, is there a simple way to edit anything in the synchronization process, and if so how? 
    Thanks!

    Thanks for your reply, but this script will result in the format "John Quincy"
    I need a script that will result in the following format: "John Q.".
    The script will need to extract the middle initial (first character) of the "EMP_MiddleName" field.

  • PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME

    PROBLEMS SETTING UP EMAILS AS DEVICE REFUSES TO RECOGNISE PASSWORD AND/OR USER NAME
    My 9800 ( I have 2 - one spare )  is driving me nuts- will not let me set up email accounts from my other Curve model.
    Repeatedly told that either user name or details are wrong, yet they are RIGHT on website.
    Exasperated 
    Help please??
    Fair winds and kind landfalls

    Thank you- I have read through that thread and can see some resonance with my issue.
    My AOL emails work VERY fast with BB, in fact almost simultaneously received on PC & Torch " ping ping!"
    This issue only raised its ugly head when I had 2 Torches replaced by my insurers. 
    Whilst the claim was in process I used a new Curve, loaded from backup on PC to keep emails going and of course phone & web facilities. ( I use the BB to power internet via bluetooth to my PC / laptop when living on a remote island with no phone lines or power supplies)  All was fine. Swapping email accounts took a few minutes with the usual password confirmations for each AOL screenname etc. 
    Then the new Torches came back from insurers, and I tried to swap devices. Phoning & texting is fine. Al data and contacts swap over fine.
    SETUP email accounts.............stymied every time. It says repeatedly that my user name/password is invalid etc etc etc
    Have tried security wipes. Have tried setting up new BB ID & passwords on PC website. All is OK until I try to setup emails on the Torches.  This has used up ridiculous amounts of time- all wasted.
    I love the BB phones and the fast email push......in fact I recently bought a new Sony Xperia Z1 but sent it back because of wifi coverage meant no emails on that superb phone for lots of the time.
    Good old BB I said..........I always get emails wherever I am. ( Rural Scotland has very patchy radio & wifi coverage)  
    Was about to purchase new Z10s just to get a bigger screen, but now I am averse to buying ANY BB phone again because this present mess means I may never get emails set up again.  How nuts is that?
    Many thanks for all help & suggestions..........boy do I need them!!
    Kind wishes from West of Scotland 
    Fair winds and kind landfalls

  • How can I sync my photo contents in iPhoto on my iMac to my new iPAD's iPhoto?  I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but I cannot find "phone button" under Device name on iTunes page. Please help!  Thanks!

    I follwed all the instructions on manuals for both iPAD and iTunes re syncing, but after physically connecting iPAD with iMac with USB or via WiFi I still cannot find "phone button" under Device name on iTunes page. Please help!  Thanks!
    I have been creating a photo book using a lots of photographs on iPhoto, and then I took another photos by using new iPAD which I want to integrate with the original album/book on iMac. I was able to import them from iPAD's iPhoto to iMac's iPhoto.  However I cannot import or transfer or sync anything from iMac's iPhoto to that of my iPAD. 
    So my iPhoto page on iPAD contains only 3 or 4 newly created albums, and no other info.  That means no syncing....
    I am supposed to be able to work on this project on either of these iPAD and iMac, correct?
    I am puzzled.  I appreciate for your advice and help.
    Thank you!

    It doesn't appear under the iPad device on the left-hand sidebar of iTunes, you need to select the iPad device on the sidebar and then select the Photos tab on the right-hand side of iTunes e.g.
    And then on the right-hand side :

  • When I import new home videos into my iTunes and edit the names it creates duplicate Library's on my Apple Tv. How can I stop this from happening each time I edit a name in iTunes home videos??

    I am having an issue with duplicate Libraries showing up in my Home Sharing "Home Videos".  It happens when I import home videos into iTunes and change the names of the files. How do I avoid this from happening and delete the duplicate libraries?

    The sort fields should generally be empty unless you've putting in custom values to sort solo artists by their surnames. You can apply common changes to thousands of tracks at once, just don't apply the wrong change because there is no undo.
    It is a good idea to backup before undertaking large scale changes. See this backup tip for a suggested approach.
    tt2
    Message was edited by: turingtest2

  • How do I download the music from iTunes onto an old iPhone 3gs? I have reset the iPhone to factory settings and when I plug it in it wants to use the device name for my current iPhone 5 and I don't want to change anything on my old iPhone.

    How do I download the music from iTunes onto an old iPhone 3gs without affecting my iPhone 5? I have reset the iPhone to factory settings and when I plug it in it wants to use the device name for my current iPhone 5 and I don't want to change anything on my current iPhone. iTunes won't let me change the device name for the 3gs. I just want to use the old iPhone like an touch.

    Hi littlemansa,
    If I am understanding you correctly, it sounds like you are returning to an old iPhone that has been erased and you would like to set it up as a new device without restoring from a backup which would affect the name of your iPhone, as well as the contents therein. I have an article for you that can help you set up your iPhone as a new device, and that information can be found below:
    How to erase your iOS device and then set it up as a new device or restore it from backups - Apple Support
    http://support.apple.com/en-us/HT4137
    Basically, it seems like you may be stuck on a screen that is asking if you would like to restore your device from the backup that is filed under the name of your new iPhone, or if you would like to set up the device as a new device. I would suggest that you set it up as a new device to achieve your desired results. 
    Take care, and thanks for visiting the Apple Support Communities.
    -Braden

  • On windows 8 and itunes 11 i try to sync my iphone and it says a duplicate file name was specified and won't let me sync, what do i do ?

    duplicate file name was specified...... windows 8 and itunes 11...... won't let me sync..... what do i do ?

    OK, read this thread... https://discussions.apple.com/thread/3928453
    tt2

  • I am getting and error message saying a duplicate file name was specified

    Help I am trying to sync new songs onto my Iphone and keep getting an error message telling me "the iphone can not be synched. a duplicate file name was specified" how can i fix this,

    I have a 27" iMac with the latest version of iTunes.  I tried restoring my iPod and even removing and re-installing iTunes.  What eventually worked for me was plugging into my PC and restoring/reformatting it to work with my PC.  I don't know why it wouldn't work with my iMac, but now it seems to be working.

  • Find monitor instance name , device name , resolution and frequency of multiple monitors (VGA and HDMI)

    hi,
    In my system multiple monitors are connected (VGA and  HDMI). In need to know the
    monitor instance name , device name , resolution and frequency of each monitor.. any solution?
    i used wm class 'WmiMonitorConnectionParams'  to determine Video output technology connection type and InstanceName.
    But i didn't get the device name , resolution and frequency of each monitor.??
    There are other wmi class like :
    WmiMonitorBrightnessEvent 
    WmiMonitorConnectionParams 
    WmiMonitorRawEEdidV1Block 
    WmiMonitorListedFrequencyRanges 
    WmiMonitorDigitalVideoInputParams 
    WmiMonitorAnalogVideoInputParams 
    WmiMonitorID 
    WmiMonitorBrightnessMethods 
    WmiMonitorBasicDisplayParams 
    WmiMonitorColorCharacteristics 
    WmiMonitorDescriptorMethods 
    WmiMonitorListedSupportedSourceM… 
    WmiMonitorBrightness 
    WmiMonitorColorXYZinCIE 
    WmiMonitorSupportedDisplayFeatures
     WmiMonitorBasicDisplayParams
     Win32_VideoController
    Win32_VideoConfiguration
    Win32_VideoSettings Win32_DisplayControllerConfiguration
    Win32_DisplayConfiguration
    But unable to determine monitor having  its corresponding values? please help me to find a solution .
    is there any other method to get multi monitor details?
    thank  you

    Hi sumith,
    I read some documents about WmiMonitorConnectionParams class, it should be able to get the video putput technology by the D3DKMDT_VIDEO_OUTPUT_TECHNOLOGY enumeration.
    D3DKMDT_VIDEO_OUTPUT_TECHNOLOGY enumeration
    So what happens when you are using WmiMonitorConnectionParams class? What prevent you? Anyway, please see a example of using WmiMonitorConnectionParams class, maybe you could get some hints on it.
    http://stackoverflow.com/questions/10085900/querying-wmi-for-d3dkmdt-video-output-technology
    Best regards,
    Shu Hu
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

Maybe you are looking for

  • How to use NiGraph control component in the MFC not measurement studio MFC??

    I want to use the NiGraph control component in the normal MFC(exe) program, but after you add the component to the project ,it will generate a CCWGraph class, and it doesnt work. If I want to use NiGraph class to plot data, What should I do? Help Tha

  • How do I transfer VI's from MAC to PC using floppies?

    I have moved 4.1 VI"s from a MAC to a Dell PC running LabView 7.0, using 1.44 Mb floppy disks. Although most of the VI displays correctly on the dell, some of the sub VI's can't be found and the VI's won't executer on the Dell.

  • Safary hangs, when clicking on the link to *.dmg or *.zip file

    Hello! Safary hangs, when clicking on the link to *.dmg or *.zip file. If I choose "save to downloads" from drop-down menu, everything is ok, but it's not always possible to choose that on the link. For example, if I try to download and install Safar

  • Downloads won't copy to itunes library

    I have a mac. I have been a safari user but would like to switch to firefox. When I get free (but not illegal, for example, using purevolume) mp3 downloads in safari, the song automatically copies into my itunes library. When firefox downloads these,

  • Help! My Ipod isn't responding to anything :-/ any ideas on what to do?

    My Ipod isn't responding to anything. I was listening to it and then I stopped listening to it. Two hours later I tried to turn in on and it wasn't turning on. I checked to see if the hold was on, I tried holding the center button for 10 seconds. I a