TFTP server on 2691 router

Dear Cisco techs,
Can someone please guide me to link on how to set up TFTP on 2691 router
When I type conf t.
tttp-server flash: is does nothing
Or tftp-server gives unrecognized command
Have searched quite a few places. Leads to various links but nothing conclusive. One directed me to a tftpdnld command but is for ios image updating only.
Want to update flash: with more files for ip phone
Why does cisco make this so difficult?
Thanks again :)

Thanks Leo. I wasn't in global config mode. All this cisco stuff is very interesting and at time challenging. LUV IT
One more question if I may.
Sh clock keep referring back to year 2002 after being updated. I unplug router. Goes back to 2002. How can I keep it as current date?
NTP server has been set but not synchronised.
Does NTP server control the sh clock command output?

Similar Messages

Send the Configuration via TFTP server to New Router/Switch

Dears,
I need to apply a policy that for any new router or switch installation, specific configuration will be sent to these devices through one centralized TFTP server which comply with our configuration and rules, this is to avoid any miss configuration from the team and control the junior network Engineer to add any wrong configuration that can effect the network, is this possible? And how?

Dears,
I
need to apply a policy that for any new router or switch installation,
specific configuration will be sent to these devices through one
centralized TFTP server which comply with our configuration and rules,
this is to avoid any miss configuration from the team and control the
junior network Engineer to add any wrong configuration that can effect
the network, is this possible? And how?
Hi,
I dont think is there any mechanism but yes to secure you can configure on router that tftp source interface for tftp server cofniguration upload and download into router or on server.
Hope to Help !!
Ganesh.H

Configuring TFTP server on a PCMCIA

I would like to know if it is possible to configure a PCMCIA card as a TFTP server and how to do so. We have a need to put large call routing files near our gatekeepers and do not have any servers or PC's close. We were wondering if it is possible to put a TFTP server (somehow) onto a PCMCIA card in a router.
Thank you

this is how you can configure a router to be TFTP server.
But I don't understand what the problem is..
If you can telnet to the router you can TFTP IOS and configs ???
Oz
Copying From One Router to Another
To do this, you need to activate the Trivial File Transfer Protocol (TFTP) server on the router that has the Cisco IOS® Software image that you want to copy.
Use the tftp-server [device]:[filename] command in global configuration mode as follows:
Router#show flash
System flash directory:
File Length Name/status
1 11173264 c2500-jos56i-l.120-9.bin
[11173328 bytes used, 5603888 available, 16777216 total]
16384K bytes of processor board System flash (Read ONLY)
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#tf
Router(config)#tftp-server ?
flash: Allow URL file TFTP load requests
flh: Allow URL file TFTP load requests
lex: Allow URL file TFTP load requests
null: Allow URL file TFTP load requests
nvram: Allow URL file TFTP load requests
system: Allow URL file TFTP load requests
Router(config)#tftp-server
Router(config)#tftp-server flash:?
flash:c2500-jos56i-l.120-9.bin
Router(config)#tftp-server flash:c2500-jos56i-l.120-9.bin
Router(config)#^Z
Router#
Once the tftp-server is configured, you can download the specified image from the router using the copy tftp flash command, as if it were a classic TFTP server.
Note: The IP address of your TFTP server is the address of the router on which you configured the tftp-server command.

How to configure logs to be sent for TFTP server !?

hi
I want to let the router or the switch to sends the log to TFTP server, how can I do that !?
including things like debug commands results
thanks,

You want to send the logs to the Syslog server..right? Use the logging command to do it.
logging x.x.x.x is the command.
Use the logging trap command to set the level of logging.
Router(config)#logging trap ?
<0-7> Logging severity level
alerts Immediate action needed (severity=1)
critical Critical conditions (severity=2)
debugging Debugging messages (severity=7)
emergencies System is unusable (severity=0)
errors Error conditions (severity=3)
informational Informational messages (severity=6)
notifications Normal but significant conditions (severity=5)
warnings Warning conditions (severity=4)
<cr>
CF

Copy all files in Flash to FTP or TFTP server

Is their a way to copy all the files at once in a router's flash to a FTP or TFTP server? Thanks.

No. On a switch you can create a tar file containing all the files and upload that one file but on routers you can only extract them. You will have to write some sort of wrapper with a chat script to do this. Sorry I don't have better news.
HTH pls rate!

How to load an IOS from CD to a tftp server?

Hi,
Hw do you copy an IOS from a CD to a tftp server? Cisco TFTP and Solar Winds 2003 Standard Edition TFTP servers are installed on a PC running Win XP.
Thanks.

Thanks for your advise. What is the procedure for mapping the directory in the tftp services?
Thanks.
Said
The following are error messages from cnsole.
Router#copy flash tftp
Source filename []? c2600-is-mz.121-4.bin
Address or name of remote host []? 172.16.40.2
Destination filename [c2600-is-mz.121-4.bin]?
%Error opening tftp://172.16.40.2/c2600-is-mz.121-4.bin (Undefined error)
Router#copy tftp flash
Address or name of remote host []? 172.16.40.2
Source filename []? c2600-io3-mz.123-9.bin
Destination filename [c2600-io3-mz.123-9.bin]?
Accessing tftp://172.16.40.2/c2600-io3-mz.123-9.bin...
%Error opening tftp://172.16.40.2/c2600-io3-mz.123-9.bin (Timed out)
Router#

Recovery image. Topology 3602i thru 2504 controller from TFTP Server

Hi everyone! Here is my topology and I need to perform image recovery for my 3602.
3602 can be connected and powered only by 2504 controller.
How I need to configure controller to allow communication from 3602 and TFTP server???
Does all ports on controller L3 and I need to make Routing thru 2921 Router?
Or no needs to configure IP ports interfaces on controller and it will work on L2.
Please give me direction to follow and recover IMAGE.

Alright! Image finally loaded!
I think it was very helpfull: Step 3 Set the timeout value on the TFTP server to 30 seconds
But image failed to boot.
But image failed to boot.

ASA 5505 Backup Config to TFTP Server

Is there a way to backup the configuration file to a tftp server? I've tried "copy start tftp" and copy run tftp". No luck, I get an error message. Thanks in advance.

What kind of error message did you get?
ciscoasa# write net ? WORD IP address of tftp server and file name :. Place IPv6 address within square brackets.

VPN between ASA5505 Easy VPN Server and 881G Router as Easy VPN Client

Hello,
I have problem in VPN between ASA5505 Easy VPN Server and 881G Router as Easy VPN Client. ASA 5505 have 7.2.3 software and 881G router have 15.1 software.
881G is configured as hardware client in network exstention mode, and it is placed behind NAT. ASA5505 is working as server. Same VPN Group works correctly from VPN software clients.
When I send traffic from 881G client side, in show cryto sessin detail I see encrypted packets. But with same command I dont see decrypted packet on ASA5505 side. On both devices Phase 1 and Phase 2 are UP.
VPN is working when I replace ASA5505 with ASA5510 correctly with have 8.4.6 software. But problem is that i need to do this VPN between ASA5505 and 881G.
Can you help me, how can I debug or troubleshoot this problem ?
I am unable to update software on ASA5505 side.

Hello,
Hire is what my config look like:
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 60 set pfs
crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 80 set pfs
crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 100 set pfs
crypto dynamic-map outside_dyn_map 100 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 120 set pfs
crypto dynamic-map outside_dyn_map 120 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 140 set pfs
crypto dynamic-map outside_dyn_map 140 set transform-set ESP-AES-128-SHA
crypto dynamic-map outside_dyn_map 160 set pfs
crypto dynamic-map outside_dyn_map 160 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 180 set pfs
crypto dynamic-map outside_dyn_map 180 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 200 set pfs
crypto dynamic-map outside_dyn_map 200 set transform-set ESP-AES-256-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 2
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
crypto isakmp policy 3
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
tunnel-group HW-CLIENT-GROUPR type ipsec-ra
tunnel-group HW-CLIENT-GROUP general-attributes
address-pool HW-CLIENT-GROUP-POOL
default-group-policy HW-CLIENT-GROUP
tunnel-group HW-CLIENT-GROUP ipsec-attributes
pre-shared-key *******
group-policy HW-CLIENT-GROUP internal
group-policy HW-CLIENT-GROUP attributes
password-storage enable
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cisco_splitTunnelAcl
nem enable

How to Setup Windows TFTP Server in Windows 2008 R2

Hi,
Can anyone please let me know, how to install TFTP Server in Windows 2008 R2.
I installed Windows Deployment Service to get TFTP (got this info in some forum), but I did not see TFTP Service in the Service Manager.
I am a newbie so plz let me know the steps in details.
Thanks in advance.

James, WDS ships with a TFTP server as part of the suite of services that are required to boot from the network. The information you've posted above is not correct.
Hi Aaron,
Thanks for your clarification. Towards the WDS TFTP Server, we could find the following statement below:
You use the Windows Deployment Services Trivial File Transfer Protocol (TFTP) server to download the files that are needed to do a network boot using the Pre-Boot Execution Environment (PXE).
From:
WDS TFTP Server
I understand that the we could select Deployment Server and Transport Server during the WDS setup processing. However, neoraghav would like to install TFTP server from the Server Manger towards the Windows Server 2008 R2. I noticed the statement as followed:
The TFTP client is optional software, and marked as deprecated on Windows Vista® and later versions of the Windows operating system. A TFTP server is no longer provided by Microsoft for similar security issues.
From:
Trivial File Transfer Protocol (TFTP) Overview
I should make my reply as clear as possible. Sorry for confusion. :-(
Regards,
James
James Xiong
TechNet Community Support

Change default block size on tftp server

Is there a way to change the default block size on the tftp server so that it defaults to 1024 instead of 512
I am aware that the client can accomplish this by:
tftp> tsize
tftp> blkzise 1024
but I don't want the client to have to enter these additional commands.

Were you ever able to get an answer on this? I have the same question.

Replacing a TFTP server in a cluster

Replacing a TFTP server in a cluster and with everything else being the same minus the MAC address on the NIC, are there any issues I could possibly run into here?
Thank you for the help the server is an MCS7845H2.

No issues, MAC address is irrelevant on TFTP as it only matters on the Pub, simply install CUCM on the new server assigning the same IP and hostname and then restore from backup.

Jabber-config.xml no longer UTF-8 after TFTP Server upload?

I have a good jabber-config.xml I edited in Notepad++ and saved (UTF-8) and I upload it to TFTP via CMPlatform on CCM 9.1.2.11900-12. I've done this in the past a lot with 8.6.2, never had any issues.
I then restart CUCM TFTP services and download;
C:\>tftp 10.7.8.3 GET jabber-config.xml
Transfer successful: 2390 bytes in 1 second(s), 2390 bytes/s
I then open up my downloaded jabber-config.xml in Notepad++ and it says the file format is UCS-2 Litle Indian and not UTF-8 and looks like the attached photo. Greek. I tried in Notepad++ to convert.
I then setup a different test PC with Windows XP, etc. Same issue, also note that plain notepad sees the same problem. Why is the jabber-config.xml file getting corrupted by the TFTP server?

ChojinDSL wrote:Do you have a firewall running on that server?
Are your clients also using systemd?
Yes I do have a firewall, iptables, and it's the same configuration from before the migration to systemd. Also note that I can access the shares when explicitly defining the path whether that's in a File Manager, cli or other so access isn't being blocked. For lack of a better explanation the whole thing gives the appearance that although the Share is active it's just not broadcasting it's existence like it should be.
I have two PC's, both Arch, one with Openbox and one running KDE that I have migrated to systemd. Both can access the Share when the path is explicitly defined but don't see it when trying to just browse for the the Share. I have a Xoom tablet, running Android Jelly Bean, that exhibits the same behavior. I also have two media players, one an older WD LiveTV Plus model the other a newer WD LiveTV model, neither of which can see the share and browsing is the only option for those devices. So I've got a pretty good assortment of devices and operating systems that could see the share when browsing previously but can not see the same share by browsing since the migration to systemd on the file server.
Thank you.

ITL file is missing on my CUCM TFTP server

Hello,
I have a problem on my CUCM cluster : the ITL.tlv files on the TFTP server (on all CUCM are missing).
When i check the file with the URL : CUCM_IP:6970/ConfigFileCacheList.txt i don't see the ITL.tlv the is just :
SEPDefault.cnf 17 1
MTPDefault.cnf 17 0
CFBDefault.cnf 17 0
SAADefault.cnf 17 1
SDADefault.cnf 17 1
lddefault.cfg 55 1
gkdefault.cfg 55 1
SIPDefault.cnf 827 1
XMLDefault.cnf.xml.sgn 8148 7
DefaultFP0000000000-c7a6c673-7479-46b0-839e-014d3d093963.xml.sgn 1863 1
CFBHW-TR.cnf.xml 2893 1
SEP123456789012.cnf.xml 7381 1
SEP0CD996911C3D.cnf.xml.sgn
I try to regenerate certificate on all CUCM, it's not OK.
CUCM version : 8.5.1.15900-4
I have 1 publisher and 2 subscriber.
Can you help me please ?
Best regards.

Yes all CUCM and phones are impacted.
There are big problem on my phone, when i restart IPphone, there are :time problem, Softkey problem, URL button, ect... .
All phone are registered on my CUCM SUbscriber1, when i execture show itl, i had a message error, i correct the issue by execute the command 'set web-security' and now when i exectue show itl i have : "The ITL file was verified successfully.".
But i have 6 records :(on my subscriber01)
TVS
TVS
CAPF
TVS
System Administrator Security Token
TFTP
TVS service is running on all CUCM.
I already tried to restart all services and the problem persists

Add tftp server settings to dhcp

I have a cisco 3750g that I use to hand out DHCP addresses. I also have a pxe server I'd like to be able to use. How would I add the next-server and the pxelinux file to the dhcp?
Thank you!

In your DHCP pool, you can define both the TFTP server and the boot file using the following format:
ip dhcp pool DHCP_Pool_LAN
next-server x.x.x.x
bootfile pxelinux.0
Just replace x.x.x.x with the address of your TFTP server.

TFTP server on 2691 router

Similar Messages

Maybe you are looking for