The application information service is disabled

hp dv7t 3065, windows 7 sp1
The application information service is disabled. This basically removes admin priv. I can't start service or do sys restore. How do i restart service without access?

You can still access the router's web configuration pages even if the internal DHCP server is disabled and it is connected via a LAN Ethernet port to your upstream router.
Did you reserve and IP addresses on the Uverse router for static IPs?
If you did, assign one of these to the Linksys router (LAN) and you will be able to access it from your LAN. Since you are not using the WAN port, the Linksys router will not pull an IP from the Uverse router. You are using the device as a switch.

Similar Messages

How do I access router setup page if the router DHCP service is disabled?

When I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?

You can still access the router's web configuration pages even if the internal DHCP server is disabled and it is connected via a LAN Ethernet port to your upstream router.
Did you reserve and IP addresses on the Uverse router for static IPs?
If you did, assign one of these to the Linksys router (LAN) and you will be able to access it from your LAN. Since you are not using the WAN port, the Linksys router will not pull an IP from the Uverse router. You are using the device as a switch.

Upgraded to Ver 8. When I am in Ms Outlook, and I click on a link, I received a message "An error occurred in sending the command to the application." Ffox did disable some Add-ons, so is this the problem?

Prior to the upgrade, with FFox open, I could click on a link in a message in the Ms Outlook 2010 program and then it would open in Ffox.
Now with every click, the full error message states "General failure. The URL was < url listed >. An error occurred in sending the command to the application." After the OK button another message asks "Was this information helpful?"
When click I received a choice of Yes, No, or Cancel with the response going to the Microsoft Customer Experience Improvement center.
It could be a Ms error but it started after the new version of Ffox.

See this lnk for a fix, it worked for me!
http://www.pcworld.com/article/200103/fix_outlook_general_failure_error_for_email_links.html

We are currently having issues fetching the applications and services list.

Is there anywhere to get an ETA or some sort of status update instead of wearing out the refresh button?

I'm still experiencing the same issue. Has the fix been made available yet? Eagerly awaiting acces!
**EDIT I'm sorry, didn't account for the time zone difference. I thought that the previous post was from hours ago. **

Only One domain controller, Remote Registry service keeps DISABLING itself. Where in the registry could this be set?

This is killing my remote management. I have 4 server 2012R2 domain controllers. Only one of them is being affected with this problem. Almost everytime I check, the remote registry service is disabled again. It seems like there is a corrupt
group policy preference that keeps on attacking during a policy refresh, but I can't imagine setting a group policy to disable this service. It is needed for our remote management. Also the IP Tunnel service is also disabling. Another strange
artifact is that when I set a Windows Firewall policy to add an exception for remote administration in a group policy to my Admin workstation, it seemed to set a firewall rule in other computers to block remote administration. I can not figure out where
else this strange Windows Firewall rule Blocking remote administration could have come from. These may be related or they may not, but they are occuring on the same domain controller. I am able to set the RemoteRegistry service to enabled and to
start it (which I have done too many times now), but it constantly is being changed back to disabled. I am searching the registry to find any invalid entries or artifacts that may be affecting these two annoying effects, but I cannot find anything yet.
Any ideas? I need to know what policies will disable the remoteregistry service OR the IPTunelling service, or where in the registry this could be set to enact this during a policy refresh. Of course, any other ideas are welcome, I have spent
several days troubleshooting this, and need to conquer this by tomorrow if possible, thank you. James

Hi,
Please type
services.msc in RUN to open Services panel, navigate to the Remote Registry service. Then open its Properties and set
Startup type: Automatic. Then please check if this issue still exist.
In addition, please refer to mlippold’s suggestion (the last reply) in following thread and configure relevant
value in RemoteRegistry registry key, then check if can help you to solve this issue.
For registry items, please back up all registry items before all operations. That will help us to avoid some unexpected issue.
Remote
Registry Service stops automatically if we do not use it above 10 minutes
By the way, did you open Event Viewer and check if find any relevant errors?
If any update, please feel free to let me know.
Hope this helps.
Best regards,
Justin Gu
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

CF8 Application Server Service Will NOT Start

I ran into this error:
java.lang.OutOfMemoryError: Java heap space
and after researching it it seemed that I should up the max heap size on the Java/JVM page, so I increased my max heap size to 1044MB from 512, via the CF Administrator, I also added maxPermSize= 256m. Then I restarted the server, but the Application Server service will not start.
I opened home/runtim/bin/jvm.config and set the heap size to 1024, restart, service still wont start.
Set the max heap size to 512 and removed maxPermSize, restarted server, service still won't start.
Set the entire java.args equal to: -server -Xmx256m -Dsun.io.useCanonCaches=false -xx:MaxPermsize=128m -XX:+UseParallelGC -Dcoldfusion.rootDir={application.home}/../ -Dcoldfusion.libPath={application.home}/../lib -Dcoldfusion.classPath={application.home}/../lib/updates,{application.home}/../lib,{appli cation.home}/../gateway/lib/,{application.home}/../wwwroot/WEB-INF/flex/jars,{application. home}/../wwwroot/WEB-INF/cfform/jars
Restarted, still the services will not start.
Does anyone have any ideas?
The error I get when trying to start the services is:
Windows could not start the ColdFusion 8 Application Server on Local Computer. For more information, review the System Even Log. If this is a non-Microsoft service, contact the service vendor, and refore to service-specific error code 2.
Thanks!

Once you have ColdFusion running again this will bring you back to your initial problem:
java.lang.OutOfMemoryError: Java heap space
Suggest take a copy of your working JVM.CONFIG (so you have a backup) then add some debugging to the JVM Arguments eg:
# Arguments to VM
java.args=-server -Xmx512m -Dsun.io.useCanonCaches=false -XX:MaxPermSize=192m -XX:+UseParallelGC -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintHeapAtGC -verbose:gc -Xloggc:cfjvmGC.log -Dcoldfusion.rootDir={application.home}/../ -Dcoldfusion.libPath={application.home}/../lib -Dcoldfusion.classPath={application.home}/../lib/updates,{application.home}/../lib,{appli cation.home}/../gateway/lib/,{application.home}/../wwwroot/WEB-INF/flex/jars,{application. home}/../wwwroot/WEB-INF/cfform/jars
Once ColdFusion is restarted again a log file will be created called \ColdFusion8\runtime\bin\cfjvmgc.log. Open the log file and you will be able to see how the New, Tenure and Permanent memory spaces are working. Given you now know which buffer is filling (excluding New made up of Eden and a couple Survivor spaces - because those fill and empty all the time) you can make adjustments to JVM.CONFIG knowing which value you intend to alter. Likely you want to alter either Xmx or MaxPermSize. When you think the Java heap space is resolved turn logging off by removing the bolded details.
HTH, Carl.

Applications and services in CC ...

Some of the applications and services in the CC site can not be seen in CC desktop application. I have a trial account, and for example, I can not see "story plus" in CC desktop application. Does this mean that desktop application is not completely syncronized with the CC accounts? So, it seems that we can not use desktop application for doing all the jobs in a CC account ... right?
And secondly, I also can not see Lightroom 5 in CC site. LR 5 is not included in CC?

Hi AttilaHan,
Not all applications are available when using a free/trial membership. The two you cited LR 5 and Adobe Story Pro are examples. If you switched to a paid membership these become available.
Regards,
Abhijit

Application Menu Services

I've always wondered: what is the services submenu item for under the application menu > services, eg: Safari > Services.

This should answer your question: Mac OS X Services.

Cannot change Application Identity service to automatic.

I am running Windows Technical Preview for Enterprise and when I try to change the startup Application Identity service to automatic, I always get access
is denied and I cannot change the Application Identity service to startup automatically.
Here is the screenshot of my error:

Are you facing this problem with all services or only this one?
Are you able to change it to different state?
Make sure report this issue using Feedback App too.
PS: You could directly add screenshot in this post by clicking on image icon and add the image.

Connection problems with the application "Remote"

I have had my iPhone for about 5 months now and I have had the application remote since I first bought it. It worked great up until I purchased a new virus protection software "McAfee... 2009" I went though the applications information and attempted to "allow" the ports that it supposedly uses, no luck.
Hopefully someone can give me a hand with this?

Sorry, you are right, the number of application modules created whe the application starts is given by the jbo.ampool.initpoolsize. But what it is sure is that the "total number of application modules in the pool" starts to decrease. The number of days is not always the same. But we have to restart the application occasionally.
I think the time parameters are ok, I would like for example 10 minutes for pool resoruce cleanup, and 10 minutes for considering an inactive AM instance in the pool as a candidate for removal during the next resource cleanup.
<jbo.ampool.monitorsleepinterval>600000</jbo.ampool.monitorsleepinterval> --> 10 minutes
<jbo.ampool.maxinactiveage>600000</jbo.ampool.minavailablesize> --> 10 minutes
Is this right?

Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.

Hi All,
I am seeing the following error for SMS_AWEBSVC_CONTROL_MANAGER component with Message ID: 8100
Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.
awebsctl.log file has below errors:
Call to HttpSendRequestSync failed for port 80 with status code 400, text: Bad Request
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
AWEBSVCs http check returned hr=0, bFailed=1
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
AWEBSVC's previous status was 1 (0 = Online, 1 = Failed, 4 = Undefined)
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
Health check request failed, status code is 400, 'Bad Request'.
SMS_AWEBSVC_CONTROL_MANAGER 12/22/2014 3:37:55 PM
13920 (0x3660)
Management point and Application Catalog Website Point are installed on the same Server where I am seeing the error for Application Catalog Web Service Point role. Management Point and Application Catalog Website Point are functioning properly. Application
Catalog Website is working.
Thanks & Regards, Kedar

Hi Jason,
Application Catalog Web Service Point and Application Catalog Website Point; both are installed as per below configuration on same Server:
IIS Website: Default Web Site
Port Number: 80
with default value for Web Application Name configured.
For SMS_AWEBSVC_CONTROL_MANAGER component, I am getting below error in Component Status:
Application Web Service Control Manager detected AWEBSVC is not responding to HTTP requests. The http status code and text is 400, Bad Request.
Possible cause: Internet Information Services (IIS) isn't configured to listen on the ports over which AWEBSVC is configured to communicate.
Solution: Verify that the designated Web Site is configured to use the same ports which AWEBSVC is configured to use.
Possible cause: The designated Web Site is disabled in IIS.
Solution: Verify that the designated Web Site is enabled, and functioning properly.
For more information, refer to Microsoft Knowledge Base.
And awebsctl.log has the below error lines:
Call to HttpSendRequestSync failed for port 80 with status code 400, text: Bad Request
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
AWEBSVCs http check returned hr=0, bFailed=1
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
AWEBSVC's previous status was 1 (0 = Online, 1 = Failed, 4 = Undefined)
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
Health check request failed, status code is 400, 'Bad Request'.
SMS_AWEBSVC_CONTROL_MANAGER
12/23/2014 11:04:36 AM 16388 (0x4004)
STATMSG: ID=8100
What should I check from IIS side?
Application Catalog Website is functioning properly.
Thanks & regards,
Kedar
Thanks & Regards, Kedar

SP2013 "Create Service Applicationt" and "Service Applications' Property" buttons are disabled

Hello,
I’ve verified that I am local admin on the server that is hosting central admin.
I run the browser as admin. In fact I am using Central Admin on the start menu. The UAC is disabled on the box any way
I run the browser on the machine that is hosing CA. I've tested in on many other machines.
I verified and my user is farm admin. That means I can see my logged-in user listed in CA->“Manage the farm administrators group”
IE Enhanced Security is off
Still I cannot create a service application or see any service application’s property. How to find where exactly is the problem?
Thank you

Hi Allan48,
What did you mean ‘cannot create a service application’?
Whether you meaned that the New service application button was disabled or not services applications were listed when you clicked the button.
By default, there are some services applications whose properties are disabled, for example Access Services Application and Excel Services Application etc.
Please make sure that SharePoint Web Services Root Application pool is running in Internet Information Services Manager, then check if this issue occurres.
I hope this helps.
Thanks,
Wendy
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Wendy Li
TechNet Community Support

Could not start the Crystal Report Application Server service on local computer

Post Author: [email protected]
CA Forum: Deployment
Hi
I have a following problem.
I have installed Crystal report application server(RAS)(CE embeded 10) on Windows server 2003 enterprise x64 edition.
When i start it, i see an error:
Could not start the Crystal Report Application Server service on local computerError 1067: the process terminated unexpectedly
Sometimes, i can start it but it stops a few minutes later.
I have disabled DEP (data execution prevention).
Log:
Faulting application crystalras.exe, version 10.0.0.533, faulting module unknown, version 0.0.0.0, fault address 0x00000000.
Please help
Thanks for your help

This error occurs after an initial install, when the Oracle suite is installed logged in as the user(who has admin rights on the machine). If this is the case,
1.Go to Services (Admin Tools > Services)
2.Double click the Oracle services( BI Server or Presentation or TNS Listener).
3.Go to Log On tab
4.If local system account is checked , un-check that option. Check "This Account" option
5.Give the user information for that machine(e.g domain\username)
6.Specify password associated with the user ( the username/pwd that is used to login to the machine)
7.Confirm pwd and click Apply.
8.re-start the service.
This is what i did , and it worked.
good luck and hopefully oracle addresses these issues , they become frustrating to use the product.
Thanks,
Ram

The Secure Store Service application Secure Store Service Proxy is not accessible

I am working on setting up a new SharePoint 2013 Farm for our external web site which is currently running on 2010 SharePoint. Because this is an External Website for our organization we have an internally available Publishing Site and there is an Web App
Extension to provide Anon Access to users using the www address. Currently I am doing everything on a single server for testing with HOSTS entries to loop back so I can test with real host headers and not impact the 2010 prod environment. We will be setting
up 2 more WFEs with a NLB before moving this into prod but it isn't there yet. We brought the Site Collection Databases over but are still running in 2010 mode for now.
I migrated a copy of the Secure Store Database over from 2010 and had it put on the 2013 Farm's Database Server. Set up Secure Store and the Secure Store Proxy. I went into the Secure Store Proxy in CA and refreshed the Key with the proper Pass Phrase. After
doing that I could see the Target Application IDs listed. Everything was looking good so I went off to test. If I am on the publishing site I can go to a page that has the solution on it and it operates as expected. It does a query to a non SharePoint database
and returns information filtered based on the search parameters. The only odd thing I see is if I click on the "Site Actions" I get a message "An error has occurred with the data fetch. Please refresh page and retry." Need to look into
that more but it only happens on pages that have these solutions. Maybe a clue. If I go to the Anonymous Access page (www......) and try and use the solution, it immediately (way too quick to appear like it is doing anything) comes back with "The security
token request cannot be completed."
If I dig through the usage logs I am finding the following.
The Secure Store Service application Secure Store Service Proxy is not accessible. The full exception text is: The security token request cannot be completed.
Unexpected exception from endpoint address : https://[Servername]:32844/4e87fd3aabb640fb8cc3ed52188cf5c0/SecureStoreService.svc/https
Logging unknown/unexpected client side exception: InvalidOperationException. This will cause this application server to be removed from the load balancer queue. Exception: System.InvalidOperationException: The security token request cannot be completed.
at Microsoft.SharePoint.SPSecurityContext.SecurityTokenForServiceContext(Uri contextUri) at Microsoft.SharePoint.SPChannelFactoryOperations.InternalCreateChannelActingAsLoggedOnUser[TChannel](ChannelFactory`1 factory, EndpointAddress
address, Uri via) at Microsoft.Office.SecureStoreService.Server.SecureStoreServiceApplicationProxy.GetChannel(Uri address) at Microsoft.Office.SecureStoreService.Server.SecureStoreServiceApplicationProxy.Execute[T](String operationName,
Boolean validateCanary, ExecuteDelegate`1 operation).
Initially I was fighting a firewall issue because it wasn't working (different errors) on both sides. Had Network Engineers open firewall ports needed and now it works on the publishing side. Still the same error on the Anon side. I suspect I have missed
something when it comes to configuring the Secure Store to allow access to anonymous connections.
Let me know if you need any more information but that should paint a pretty good picture as to how things are set up.
Thanks for any help on this one. Searches haven't found much that has helped so far.

Hi Sennister,
I recommend to verify the things below:
Did this issue occur with all the pages in the anonymous side?
Check if the Claims to Windows Token Service is started.
Change the <identity impersonate="true" /> in the web.config to see if the issue still occurs.
Thanks,
Victoria
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Victoria Xia
TechNet Community Support

The search service is not able to connect to the machine that hosts the administration component. Verify that the administration component 'GUID′ in search application 'Search Service Application' is in a good state and try again.

Another post with a well-known title. Believe me, I know. Here's my setup;
- 1 Server 2012 WFE, SharePoint Server 2013, totally up-to-date, including the september 2014 hotfix
- 1 Server 2012 DB, SQL Server 2012
Installed SP 2013 using PowerShell, with the AutoSPinstaller. Worked like a charm. Got everything up and running, with some tweaking here and there to customize it to fit my situation. Now, I can't get the Search Service Application to work. Must have created,
deleted and recreated it at least 30 times. Used both PowerShell scripts, PowerShell line-by-line, Central Admin, heck, I even went so far as to use the configuration wizzard... No luck. I keep on getting the message that search cannot connect to the machine
that hosts the 'administration component'.
In order to avoid answers that suggest all the things I've already tried, here's a summary of the various scenarios I followed:
Tried both a dedicated application pool as well as the SharePoint Web Services Default
Timer job job-application-server-admin-service is running and not showing errors
IIS 8.0 is installed, so is .NET 4.5 (not the known perp of IIS 7.5 and .NET 4.0)
the get-SPEnterpriseSearchServiceInstance -local returns a healthy, online state
the SPEnterpriseSearchQueryAndSiteSettingsServiceInstance is also running
FireWall is disabled; registry has the BackConnectionHostNames modified with the necessary FQDNs
Accounts used to install and / or run the serviceapp all have sufficient rights - tried a dedicated managed account, SP_2013_SearchSvc, the SP admin account, and even the original Farm account; all to no avail, I keep on getting the error message.
Even tried stsadm to start the server search running - NOTHING WORKS!!!
As you might understand, this is driving me nuts. About to miss my second deadline, and no amount of IISresetting is making this go away. Been stuck on this issue for far too long, now (my searching is measured in days and weeks instead of hours, by now).
Whoever helps me solve this - you will have my eternal gratitude, and a nice bottle of Prosecco. Or whatever's your poison. You need to come get it, though. I´m situated in the Netherlands. Hey, you always meant to visit Amsterdam and see for yourself, right?
Thanks, community, for coming to my rescue!

Thanks again - Alas, I've been there. Deleted Search a dozen times, at least, and tried installing it, initially using a PowerShell script (tried several scripts actually, from full-blown total Search Applications with extensive topologies to the most basic
of basics 'please just start without showing me errors'), PowerShell line-by-line to see where things went South, next tried installing through Central Admin (hoping that it was my own stupidity in overlooking things and hoping The System would get it right
for me), and eventually even tried using the config wizzard as a total and utter last resort - Nothing worked.
At first, I found out that removing a Service App needs a *little* bit more work than simply removing it through Central Admin, but by now I can truthfully state that if there's one thing I've become supergood at, it's removing Search Service Applications.Totally.
I will check out the article, though - I realized early on in my SharePoint experience that regardless of what you think you know, there's so much more to find out. I know, that's almost philosophical. That is, my friends, indeed the point I've reached...

The application information service is disabled

Similar Messages

Maybe you are looking for