"The attached ipod model is not supported by this applicatio

HELP! I installed my ipod nano and it all worked fine, got a few songs on it. So i downloaded some more, ripped a CD i had and did nothing particularly life changing. Going back into i-tunes it all went a bit funny and came up with a message saying "Cannot read ipod please reset to factory settings" So i went into ipod updater (the version that was on the CD that came WITH the ipod) and was told "The attached ipod model is not supported by this application" so i went onto the apple website and downloaded the latest version of the ipod program, tried again and the same message appeared: "The attached ipod model is not supported by this application" any ideas?!?!?!

Well let's assume you already have Ituenes 5.01 than if you can see the Nano as a mounted drive in My Computer I would recommend reformatting the Nano with FAT32 from there. Than try running Ipod updater again. Sorry I can't think of anything else right now, try searching around or see if someone comes to you on of your many forms. That's another reason not to double post those that are trying to help you don't know what else has already been suggested.

Similar Messages

  • The attached iPod model is not supported by this application

    I just bought a 20G color iPod. I spoke w/ the Apple tech support & I needed service pack 2. I downloaded it. I didn't have a USB 2.0 port then I installed one. I downloaded the latest Apple updater software 2005-06-26 then I tried the even later version 2005-09-06. When I go into updater, it says it is "initializing" and then says "the attached iPod model is not supported by this application." Reformat and restore are both grayed out. iPod doesn't show up in iTunes and doesn't transfer my library. I just got back from the Apple Store and the suppossed "genius" said the iPod is fine and it is my computer. WHAT is wrong with my computer?

    Brad,
    you ought a little bit more descriptive! What Version of iTunes are you using? Check the software version of your iPod (if it even has one yet) under Settings-About. Your iTunes and iPod software have to be compatible. If you're running 4.9 you need 2005-06-26. Close iTunes and leave it alone. Deinstall all iPod related software, clean the registry if you want (I don't think this is so much necessary for the iPod software). Then install 2005-06-26 again on your computer first!! Don't connect the iPod. After having installed it, open the Updater, then connect. Before you do that and since you don't have any music on the iPod reset it to factory settings under Settings-Reset all settings. Or at least reset it with pushing Menue and the center knob at once. Many possibilities I know, but either one will work...after that it will remain seen by iTunes and you're a lucky guy (hopefully).
    Best regards
    Roman

  • Do the Mac minis support using AirPlay and all of its functions?   I thought I saw a comment yesterday that suggested the Mac mini (particularly the late 2012 models) does not support AirPlay.  Thank you.

    Do the Mac minis support using AirPlay and all of its functions?   I thought I saw a comment yesterday that suggested the Mac mini (particularly the late 2012 models) does not support AirPlay.  Thank you.

    Hello,
    AirPlay Mirroring
    Requires a second-generation Apple TV or later. Supports the following Mac models:
    iMac (Mid 2011 or newer)
    Mac mini (Mid 2011 or newer)
    MacBook Air (Mid 2011 or newer)
    MacBook Pro (Early 2011 or newer)
    http://support.apple.com/kb/HT5444

  • Kit iPad Camera Connection: The attached USB device is not supported

    Las fotos en las tarjetas SD tienen que estar dentro de una carpeta llamada "DCIM" en el raiz de la tarjeta. si no te da Error: The attached USB device is not supported.

    lllaass wrote:
    The Apple page for the CCK says: iPhone 3G is not supported. Do not know why this one iPhone is not supported.
    Please post the URL. I remember reading specs where the iPhone 3G was singled out as not being compliant with an accessory and can't remember with one.
    From Apple page on the CCK. The iPad is the only device that works with it. But, you can use it to transfer photos and videos between the iPad and iPhone. Go figure...

  • When trying to play videos I get the message "requested URL is not supported on this network" how do I fix this?

    I receive the error "requested URL is not supported on this network" when trying to play videos on my iPhone. Can you please advise how to fix this problem?

    Hi,
    You will need to re-instal iCal as an optional install from your OSX installer DVDs. Then run the Mac OS X 10.5.8 Combo Update.
    Best wishes

  • In SharePoinr 2013. Unsupported Reporting Services Functionality The feature: "Power View" is not supported in this edition of Reporting Services.

    Hi,
    I am getting the below error which click "Create Power View Report" option in "Power Pivot Gallery"
    Unsupported Reporting Services Functionality
    The feature: "Power View" is not supported in this edition of Reporting Services.
    I have uploaded "Power Pivot" excel file in "Power Pivot Gallery".
    It is frustrating like anything. Can anyone help on it.
    SharePoint 2013. SQL Server 2012. I have enable all the service applications success in CA.
    Thanks in Advance.
    Poomani Sankaran

    Hi,
    Please try to download the SP1 Edition of the rsSharePoint.msi
    file and install it. You have to install the SP1 edition of RS if you are using SP 2013.
    Here is a similar thread for your reference:
    http://social.technet.microsoft.com/Forums/en-US/2d2ecfae-b524-43f3-bf93-0bddfe904b75/the-feature-power-view-is-not-supported-in-this-edition-of-reporting-services?forum=sharepointadmin
    Best Regards
    Dennis Guo
    TechNet Community Support

  • When i try to open the iPhoto app, i getting a message "you can't open the application because it is not supported on this type of mac"

    when i try to open the iPhoto app, i getting a message "you can't open the application because it is not supported on this type of mac"

    To re-install iPhoto
    1. Put the iPhoto.app in the trash (Drag it from your Applications Folder to the trash)
    2. Download it from the App Store to reinstall It's on your Purchases List* there.
    For older versions that have been installed from Disk you'll need these additional steps:
    2a: On 10.5:  Go to HD/Library/Receipts and remove any pkg file there with iPhoto in the name.
    2b: On 10.6: Those receipts may be found as follows:  In the Finder use the Go menu and select Go To Folder. In the resulting window type
    /var/db/receipts/
    2c: on 10.7 or later they're at
    /private/var/db/receipts
    A Finder Window will open at that location and you can remove the iPhoto pkg files.
    3. Re-install.
    If you purchased an iLife Disk, then iPhoto is on it.
    If iPhoto was installed on your Mac when you go it then it’s on the System Restore disks that came with your Mac. Insert the first one and opt to ‘Install Bundled Applications Only.
    *Sometimes iPhoto is not visible on the Purchases List. it may be hidden. See this article for details on how to unhide it.
    http://support.apple.com/kb/HT4928
    One question often asked: Will I lose my Photos if I reinstall?
    iPhoto the application and the iPhoto Library are two different parts of the iPhoto programme. So, reinstalling the app should not affect the Library. BUT you should always have a back up before doing this kind of work. Always.

  • "The feature Power View is not supported in this edition of Reporting Services" after installation of November CU for SharePoint

    We had deployed Reporting Services / PowerPivot /Powerview for a customer and everything was tested and appeared to be working fine . However after installing the November CU we now get the following error :
    "The feature Power View is not supported in this edition of Reporting Services"
    Initially PowerPivot wasn't working either but that got resolved after re-installing the rssharepoint and sppowerpivot msi files. Has anyone faced this issue?

    Hi,
    According to your description, my understanding is that the PowerView not work after installing the November CU Updates.
    I check the November CU updates, it have no affects on the PowerView or PowerPivot.
    The reason for this issue may occur when the PowerPivot Service Application is not running after installing the CU updates.
    Here is a detailed article for your reference:
    http://support2.microsoft.com/default.aspx?scid=kb;EN-US;2889944
    Best Regards
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Jerry Guo
    TechNet Community Support

  • Firefox 4 unable to use on imac G5 ( without intel chips ), get messageYou can't open the application bcz it is not supported on this architecture.

    My iMac G5 without intel chips, Mac OS X 10.5.8.
    using Firefox 364 no problem at all.
    But unable to install Firefox 4 on it, prompt "You can't open the application because it is not supported on this architecture"

    Firefox 4 requires at least OS X 10.5 and an Intel Mac.
    There is a third-party version of Firefox 4 that works on PPC Macs, for details see http://www.floodgap.com/software/tenfourfox

  • What does "you cannot open the application because it is not supported on this architecture" mean?

    What does "you cannot open the application because it is not supported on this architecture" mean?

    well my mac lion (10.4.11) will run minecraft.jar, but runs very slow , i tried downloading minecraft.zip it showed the mc logo with a x on it, i tried opening it, and it said it cant open it because there is no application to open it, do i need a higher version of mac? mainly leopard or snow leopard? This is what it looks like

  • The :pserver: access method is not supported by this port of CVS

    i receive the following error when trying to connect to cvs
    the :pserver: access method is not supported by this port of CVS

    i receive the following error when trying to connect to cvs
    the :pserver: access method is not supported by this port of CVS Use the CVS 1.11.2 from http://www.cvshome.org, sounds like you are using a version of cvs which (is maybe CVSNT) doesn't support pserver.
    Rob

  • I updated to ios6 and now imessege does not work, and my dock says "ipod touch is not supported by this accessory, what happened??

    i was using imessege all the time, working perfectly, and my dock is what u played music on and charged my ipod on every night, then after i updated it, none of it works anymore???
    this also happened to a buddy of mine, exact same problems
    please help

    iMessage - Sorry, I don't know.
    Dock - The same thing is "sorta" happening with a belkin charger that I have. It'll say that charging is not supported wij this accessory, and I can't use the Belkin cord any longer. I have to use my apple one. I think that means that the dock software is now "outdated" and can't charge your iPod anymore.

  • Trying to open a sharepoint library in Windows Explorer via IE 8 results in the error "your client does not support opening this list with windows explorer"

    I am attempting to connect to a Microsoft Sharepoint library, via the "Actions -> Open in Windows Explorer" option from the Sharepoint page.  When I do so, I get the error message "your client does not support opening this list with windows explorer".  In short, I am trying to get the "drag and drop" functionality of a Sharepoint library.
    I am running Windows 7 64-bit and IE8.  The target Sharepoint environment is a MOSS 2007 EE.  My Windows "WebClient" service is running, and I have no problem connecting to this exact library via a Windows XP computer running IE8.

    Verify that the Webclient is started automatically from the Services.msc
    Verify that your Portal is in the Intranet local security zone (You can reach it from Your Internet Explorer Browser Security Tag) if not add it to the list
    restart the WebClient service if it's work good
    If not you have to create a network share to your portal URL directly not your documents library.
    Open Windows Explorer or My Computer from the Windows Start Menu.
    From the Tools menu, click Map Network Drive…. A new Map Network Drive window opens.
    In the Map Network Drive window, choose an available drive letter from the dropdown list located next to the "Drive:" option. Any drives already mapped will have a shared folder name displayed inside the dropdown list, next to the drive letter.
    Type the name of the folder to map wich is in this case your SharePoint Portal URL (Don't include the documents libraries)
    Click the "Reconnect at login" checkbox if this network drive should be mapped permanently. Otherwise, this drive will un-map when the user logs out of this computer.
    If the remote computer that contains the shared folder requires a different username and password to log in, click the "different user name" hyperlink to enter this information.
    Click Finish.
    I am looking for a suite method :)

  • Director PowerPC processors (PPC ) can't open the application because it is "not supported on this a

    I created a projector in Adobe Director 11.5 for the Mac.
    For some reason PowerPC processors (PPC ) can't open it because they received a message saying the application is "not supported on this architecture."
    And idea if there is a way to make projectors compatible for the Mac PPC processors?
    Thanks,

    Check your product version by typing "put the productVersion" into the message panel - if you don't get the response "11.5.9" then update the to latest patch by selecting the Update option from Director's Help menu. (I suspect you already are on 11.5.9, though, otherwise you wouldn't get this problem).
    Next, go to the Publish Settings page, and under the projector tab you will notice an option to create the Mac projector as either a "Universal Binary" or an "Intel Binary"
    Universal Binary will run natively on PPC Macs, and will run under Rosetta on Intel Macs running up-to-and-including OSX 10.6 (Snow Leopard).
    Intel Binary will run on all Intel Macs running OSX 10.5 and upwards.
    Rosetta is a virtualisation layer built into OSX versions up to 10.6; It allows programs written for PPC to run on Intel Macs. Rosetta was dropped from OSX 10.7 (Lion), so a UB projector won't work on Lion.
    Hope that helps
    Message was edited by: Adam-C

  • Firefox can't open the application "because it is not supported on this architecture

    "You cannot open the application "Firefox" because it is not supported on this architecture."

    Thanks for the link to the system requirements, edmeister. However, my system appears to fit every requirements listed, but still gives the same error message.
    Here is what my system profiler tells me about my Imac:
    Mac OS X v. 10.5.8
    Processor: 2 GHz Intel Core 2 Duo, which Wikipedia tells me is "x86" processor
    3 GB 667 MHz DDR2 SDRAM
    My Activity Monitor says:
    1.87 GB of my system memory free
    303 GB of hard disk space free
    Is there some explanation why I am being told Firefox 4 is not being supported on this architecture?

Maybe you are looking for

  • Insert OR Update records

    Hi All, I want to write a stored procedure to insert or update the value into the customer table. If the record exist, I need to insert. If it does not exist, I need to update. Could you tell me how do we do it. My Current stored procedure is : CREAT

  • Seagate goflex 2TB external drive not mounting Yosemite.

    Hello: I have been using a Seagate golfer 2TB external HD for time machine since 2012. No problem with subsequent OS X upgrades. My last backup was performed 3 months ago in an iMac with Mavericks. Today I have a new iMac with Yosemite. Due to the ne

  • App already bought problem

    I bought an app call IShutdown last year on my ipad 2!, and i recently bought an Iphone5 i want to use that app, i read on this support communities that i can download it without paying it again, 2 days ago apple send me the billing for this app!, it

  • Compatibiltiy

    Hi All, We have OS- Solaris 10(64-bit); OC4J 10.1.3.4. Is it possible to put the ASF apache 2.2 (64 bit)/IBM HTTP 7.0 (64 bit)/IBM HTTP 6.1 (64 bit) into the OC4J 10.1.3.4? Thanks, Viji

  • Global UCCX deployment - maximum network latency permitted?

    We are looking at a global deployment of UCCX. The number of agents will be small, around 25 in total, but globally dispersed. What is the maximum network latency UCCX can tolerate? We would be looking to have the UCCX server, PSTN connection and CUC