'The cable for the PCI Ethernet is not plugged in' error

Hi everyone, I've installed a PCI network card for my G5, 1.8 (later model) single processor, and checked to make sure the card has the Realtek chips.
I've tried the D-Link DGE-528T which is meant to be OSX compatible but to no avail. I get the 'The cable for the PCI Ethernet is not plugged in' message. I've then tried the Pluscom with Realtek 8169 chip and again, get the same message.
I have a good understanding of networking, have installed several drivers, sometimes manually and I've used the terminal to recode the permissions. I've also removed the extension cache file but still no luck. I've also made sure to follow each install path from the package file and remove any older drivers. I've also installed the card in slot 1.
I don't think it is the card. Does anyone have any other ideas I could try?

Where did you get the drivers?
I've heard of people using D-Link routers, and even D-Link's USB/Wireless adapter, but I've never encountered anyone using a D-Link PCI ethernet card. A quick search didn't find any drivers and without that you're not going to get very far. I'm mildly impressed that the OS recognizes the card at all.

Similar Messages

  • The cable for Built-in Ethernet is not plugged in

    Hi this is my 1st time on this discussion forum and I'd appreciate it if I could get some help to resolve this issue. The problem began with another fault ‘Your network settings have been changed by another app' but I solved this with a solution from this forum. My computer was working fine before this.
    With this second issue, I have tried everything to fix it but without success. The network settings are correct. The cable is fine as it works on another computer. I have used another cable as well. The light on hub shows it is connected. I have tried plugging it directly into the router and many more. The problem is definitely software and possibly from an update. Please help as I have search the internet for days to find a solution.

    Hello Yabbynz, and a warm welcome to the forums!
    For a start, type this into the bowser's URL bar...
    17.254.3.183
    If that gets you to apple.com, then try putting these numbers in Network>TCP/IP>DNS Servers for the Interface you're using...
    208.67.222.222
    208.67.220.220
    Then Apply. These are safer/faster than most ISP's DNS numbers, and have been patched against DNS poisoning.
    https://www.opendns.com/homenetwork/start/device/apple-osx-tiger
    If not, report back.

  • Why is the cable for the shuffle so short

    why is the cable for the shuffle so short<should there be 2 cables.I have to havemy ipod dangling from the side of my computer(i have an all in one)

    Assuming you have a 4th gen shuffle, it should be fine hanging off the computer, since the shuffle is so light.  You can think of that cable that comes with the 4th gen shuffle as being more of an "adapter."
    If you want a long cable, you can buy the replacement part.  It comes with both a short adapter (like the one you have) and a long cable. 
    http://store.apple.com/us/product/MC003ZM/A/apple-ipod-shuffle-usb-cable
    I use a USB hub, which I can conveniently locate on my desk.  I connect the shuffle (and my other iPod/iPhone) to the hub.  If you want a hub, make sure you get one that is self-powered (it has it's own power supply).

  • Do the cables for the 700p work with the 700wx?

    I used to have a treo 700p that I broke when I dropped it from a 2nd story balcony onto concrete. I still have the box and whatever cables came with it. Now, I'm able to buy a 700wx for a real low price, but the seller only has the phone and the charger for it, no other cables. Would the cables for my 700p, like the sync cable work with the 700wx? If they would, this would work out real nice!
    Post relates to: Treo 700p (Sprint)

    Yes it will work most of the cables for the Treo series will work as it is an interchangeable cable, there is some exceptions, but in your case it will work.

  • Want to connect MacBook Pro to the internet via ethernet cable for the first time?

    I Plugg the cable for Ethernet> Then I type my IP adress> don't know what to type in these blanks:
    Subnet Mask, Router
    What DNS?
    I want to plug the cable for Ethernet then see the internet work?
    =

    We cannot answer your questions.. and the method looks wrong.. why are you doing it manually.. just use dhcp and see if it works.
    There is hardly a modem or router out there that doesn't have dhcp setup for automatic setups.
    If it is manual then there is no way we can give you the values..
    They are determined 100% by the network you plug the computer into.. and the setting of that network.
    Tell us more if you supply modem router.. and ISP info and why it is not working with dhcp we might be able to help further.

  • HT201412 My ipjone keeps coming up with a message say that the cable or accessory urged in is not a reliable source for this iPhone but I do not have Nything plugged in to my iPhone. I Put it in a bowl of rice for 2 hours to see if that would help it but

    My ipjone keeps coming up with a message say that the cable or accessory urged in is not a reliable source for this iPhone but I do not have Nything plugged in to my iPhone. I Put it in a bowl of rice for 2 hours to see if that would help it but it hasn't. Is there anything thank can do???

    Clean the connector on the bottom of the phone. Use a magnifying glass, bright light, and a wood or plastic toothpick. If you got the phone wet put it in a bag of uncooked rice for several days, not hours.

  • What is the best charging cable for the iPad Air (that is not made by Apple)? I need a long cable (over 6ft or more). I also need the cable to be of high quality and the cord part of the cable to be made of strong material.

    What is the best charging cable for the iPad Air (that is not made by Apple)? I need a long cable (over 6ft or more). I also need the cable to be of high quality and the cord part of the cable to be made of strong material. Apple does not make one this long. Is there a cable out there that is sturdy like this and is safe to use?

    yes, but I'm trying to use my iPad to type notes (using pages) and I have the smart case which I use as a stand. I need a cable long enough to fit through the back of my desk and the charging brick for the iPad won't fit behind the desk. I have to put it on the floor and then the apple cables aren't long enough to reach.

  • HT5706 After the update the Apple TV will not work -  It puts up a symbol to connect to the Icloud - which I do not have the cable for or know what it means or why -  Message do not update if it works

    After the update to the Apple TV, it will not work -  It puts up a symbol to connect to the Icloud - which I do not have the cable for or know what it means or why - 
    Message to users is, do not update if it works.  This product apparently was not tested very well

    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Source list, and then click Restore.
    If when you choose restore you get a message that the device cannot be found, download the file below
    Apple TV Software Restore 5.1.1 (2nd generation)
    Apple TV Software Restore 5.1.1 (3rd generation)
    Then hold down the option key while choosing restore and select the downloaded file when prompted.

  • I have been trying to update to iOS 5 and every time I hit update it says, " There was a problem downloading the software for the iPhone. The network connection could not be established."  What do I need to do to update to solve this problem?

    I have been trying to update my iPhone 4 with iOS 5 for about 30 minutes and I keep getting the same thing. It says,"There was a problem downloading the software for the iPhone. The network connection could not be established." What do I need to do to solve this problem?

    iOS: Resolving update and restore alert messages
    For error -50: See error 13 and 14: 
    Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
    Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting.
    Put a USB 2.0 hub between the device and the computer.
    Try a different USB 30-pin dock-connector cable.
    Eliminate third-party security software conflicts.
    There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.
    Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online.
    Try to restore from another known-good computer and network.

  • Dimensions of the 160-Pin Cable for the NI PXI-2530B

    Hello,
    My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
    Thanks!
    Solved!
    Go to Solution.

    JKSH wrote:
    Hello,
    My mechanical design team wants to know the measurements of the 160-Pin Cable for the NI PXI-2530B. It will be a while before we receive the cable we ordered. I could not find a data sheet with the measurement details; are they? Alternatively, is Figure 1 in the Installation Instructions drawn to scale?: http://www.ni.com/pdf/manuals/375656b.pdf
    Thanks!
    What dimensions are you looking for?
    I'm a little surprised that the length of the cables is not included in the datasheets (I did just look!) - I thought that when I ordered cables for the older-style PXI-2530 modules in my lab that the length was specified in the part description.
    If you need the dimensions of the connectors, you can do a little reverse-engineering and identify the dimensions of the various components. The connector to the module is an LFH-160. The Digikey P/N for the body of a connector is WM4099-ND. It may be difficult to find the dimensions of the backshells, however.  The 4 terminal block connectors are standard 50-pin D-Subs. There are many examples out whose dimensions you can review.
    Jeff
    Jeffrey Zola

  • Shorter USB cable for the Dinc 2

    Looking for a shorter length USB cable than the one that came with the phone.
    Does anyone know if they make a short length (less than 3') USB cable for the Dinc 2?
    If so where could I get one?
    Thanks again.

    You have heard of 'Tethering' witch is only available on the iPhone but not in the US (thank you AT&T). That is only for using the iPhone to connect a computer to the internet. Sorry

  • Do I need to buy any extra cables for the airport express??

    I was wondering if i need to buy any extra cables for the airport exprees.what kind of cables do i have to get to connect the airport express to my DSL modem?

    Typically all you would need is an Ethernet cable (cat5, rj45 end), and it would be connected to the LAN port on the DSL modem, and the Ethernet jack on the AP Express.

  • TS2518 Help, I had aperture open and working on a image and did not have a battery in and bumped the power off. As a result it will not open my master, it is locked. when I try to open that Library  it says There was an error opening the database for the

    Help, I had aperture open and working on a image and did not have a battery in and bumped the power off. As a result it will not open my master, it is locked. when I try to open that Library  it says There was an error opening the database for the library. I have tried every thing. I updated the other libr but now it will not open the main to update. What do I do?

    Try starting Aperture with the command and option keys held down.  You'll get 3 options.
    Try each, starting at the top, in order, checking after each to see if it fixes the issue.

  • Can't install the software for the Brother MFC-9440CN because it is not currently available from the Software Update server....how do I get the driver then..it ised to work in my old mac..but cant print to it in my new unit

    Can't install the software for the Brother MFC-9440CN because it is not currently available from the Software Update server....how do I get the driver then..it ised to work in my old mac..but cant print to it in my new unit

    Download the Brother Mountain Lion drivers here.

  • HT201269 When I try to setup my new iPad air, I go through all the steps for the iCloud sign-in and choosing security questions and what not. But after I hit the agree to the terms and conditions... It says Apple ID could not be created because of a serve

    When I try to setup my new iPad air, I go through all the steps for the iCloud sign-in and choosing security questions and what not. But after I hit the agree to the terms and conditions... It says Apple ID could not be created because of a server error. Have no clue what to do... I've restarted the iPad and get the same message. But my internet works just fine.

    1. Turn router off for 30 seconds and on again
    2. Settings>General>Reset>Reset Network Settings

Maybe you are looking for

  • Automated MetaData Load

    Greetings, I'm curious to know how some of the users in this forum perform automated metadata load against dimensions in the Shared Library (and subsequently against any EPMA Planning apps). We have several apps whose dimensions are shared amongst va

  • Is the Mac Mini right for me?

    I've been fighting with my PC for years, and I am finally giving up. I'm looking forward to joining the Mac community. I want to buy a mac mini with the new Leopard OSX(10.5), however, I have some unique requirements: - I live on a boat in Avalon Har

  • Purchasing Groups for multiple Purchase Organizations

    Dear all, in SRM 5.0 we are using two different purchase organizations which are linked to backend purchase organizations in extended classeical szenario. When I try to assign purchasing groups linked to backend purchasing groups to both both purchas

  • Trouble converting RAW files with Camera RAW/DNG - CS4 Mac

    Hello! I am using CS4, with Camera RAW 5.7 and Adobe DNG 5.7.  These are the versions listed as compatible with CS4.  I am using a new Canon Powershot S100.  Can I use newer versions of the RAW/DNG with CS4, or am I just out of luck? Please help! car

  • Server Network Address on Clustered Instance

    Hi, I am looking to configure database mirroring and as part of this need to specify the server network address. The primary instance is on a 2 node cluster and the mirror data base is on a separate instance on a standalone server. When creating the