The connection between your access point, router, or cable modem and Internet is broken
When I turn on my computer, this problem came out as the title. I don't know why, but it can not connect to the Internet. The Internet is OK, my another computer could connect it. Anyone can solve the problem? Thank you very much!
Hi,
Try to reset the TCP/IP stack go to this article and either click on "Fix it for me" or follow the instructions to fix it yourself:
How to reset TCP/IP by using the NetShell utility
http://support.microsoft.com/kb/299357
Also you could try to reset winsock to check if it helps.
To do this, follow these steps:
1. Click Start, and in Start Search, type cmd.
2. Right-click the cmd entry that appears in the search results, and then click ‘Run as administrator’. If you are prompted for an administrator password or for a confirmation, type the password, or click Continue.
3. At the command prompt, type the following, and then press ENTER:
netsh winsock reset
Then, you should see the following message:
Successfully reset the Winsock Catalog. You must restart the computer in order to complete the reset.
Restart the computer and check if it works fine.
Karen Hu
TechNet Community Support
Similar Messages
-
The connection between your access point, router, or cable modem and the Internet is broken.
At random points throughout my laptop usage, I randomly disconnect from the internet and receive these 2 messages:
1. The connection between your access point, router, or cable modem and the Internet is broken.
2. The default gateway is not available.
It fixes the issue for a short period of time, but constantly happens. This is really starting to annoy me. I have no problems on any other internet, and other people i live with are connected with no issues to the internet. I have tried a number of solutions
online that has "worked" for others to no success such as resetting the router, fooling around with command prompt, and changing the performance settings to not drop internet when low on power. Does anyone have a solution for my technical problems?
I am running Windows 8.1 on a Lenovo ideapad that is less than a year old. I will be honest I am not a very knowledgeable person when it comes to computers, so please use simplified explanations.Checked this ?
http://answers.microsoft.com/en-us/windows/forum/windows_7-networking/window-networking-troubleshoot-error-the/c130ede9-757e-4224-9ae8-3cceb82eeb74
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread. -
Hi.
I read the posting regarding the options on Hotsyncing for Windows 7; however, I have some questions as I have a 64-bit system.
I have a Visor Pro that I'm trying to Sync up with my new laptop which is running Windows 7.
Steps I have taken:
* installed the Visor Palm Desktop 3.0.1 that came with the Visor (which the installation went well)
* The issue arises when I push the "Sync" button on the cradle and the following error message appears "The connection between your handheld computer and the destktop could not be established. Please check your setup and try again."
Since I have a 64-bit OS it appears that I have 2 options: 1) bluetooth or 2) Infrared.
I have to admit I don't know know how to do either of these (how can I tell if this Handspring Visor Pro has bluetooth (which I don't it does)?).
Then how about the Infrared option? I see on the PDA it has a red area that one can "beam" info. Is this the same as Infrared or my 2nd option?
I love my Visor and want to continue using it, but need to backup the valuable info!
Any help with this would be greatly appreciated!
THANKS!!!!!
Post relates to: Visor ProHello lwalbring and welcome to the Palm forums.
Your Visor, as you suspect, does not have Bluetooth, so you must use the IR HotSync option. Since you are using Windows 7 64-bit, I believe that you are going to have to upgrade to Palm Desktop 6.2.2 to make things work from an OS/Driver perspective.
Since you are using such an old device, you are also going to have to download and install the PalmHotSyncSetup Utility from Pimlico. This update turns on support for old Palm OS PDAs in Palm Desktop 6.2.2. Without the update, you won't be able to sync your Visor with Palm Desktop 6.2.2. The software is free and the link is all the way at the bottom of the screen.
Lastly, if your PC doesn't have an IR port on it, you will need to purchase a USB to IR adapter. Some laptops still have IR ports and most desktops don't.
Once you have all the pieces, you'll want to go back to the Windows 7 and Vista HotSync thread again, and follow the directions for setting up and configuring IR HotSyncs.
Alan G -
Hi,
I am running XP SP 2, on a Dell Vostro 1000, Palm OS Garnet v5.4.7 on a Tungsten E2. I have worked though issues relating to synchronization, Outlook 2007, Docs to Go, etc., in the past. Thank you board members!
Once I worked thru all the initial problems, my Tungsten E2 was sync' ing beautifully to my laptop until a few days ago. There have been no changes (I know of) to the configuration, but now I receive "The connection between your device and the desktop could not be established. Please check your setup and try again." On the laptop I sometimes get "USB device not recognized." I am unclear why I get the PC message sometimes and not others.
I have tried the following: (not necc exactly in this order)
Double checked Hot Sync Mgr settings: Local USB (ver. 6.0.1)
Reset the Palm (multiple times)
Rebooted the laptop (multiple times before and after the Palm resets)
Went to Support Libraries including http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=57,E=0000000001060189973,K=9550,Sxi=3,Case=Obj(3695...)
and http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE?New,Kb=PalmSupportKB,ts=Palm_External2001,Case=obj(1409)
Followed the steps in "Start Here" found at http://forums.palm.com/palm/board/message?board.id=windows_hotsync&thread.id=26057
Moved Backup directory as per a post on this forum
Looked for a deleted a file called "Graffiti_ShortCuts_____________" per a post on this forum
Followed the steps in HotSync troubleshooter guide you can run through located on
http://kb.palm.com
Went into Device Manager - found it shows no yellow ! 's
Followed Device Mgr Troubleshooter - went all the way thru with no solution
Tried all four USB ports - the PC's bell-like tone does not sound when I disconnect or reconnect the Plam's cradle like it does when I conn/disconnect other USB devices -I think that is a clue. ...?
Cleaned the Palm's contacts (and cradle's contacts with a old, dry toothbrush)
Read all the posts under "USB device not recognized."
OK, I'm at a loss, can anyone help me? Many thanks in advance!
~Bob
Post relates to: Tungsten E2Hello!
Using a cradle with the Tungsten E2? Tried bypassing the cradle and just use the hotsync cable? Tried a different computer yet? Somehow, the PC is having problems getting a signal from the device. I assume you have the laptop charger plugged into the laptop during this? Not going through a docking station or port-replicator.
One crazy thing you can try is unplug the charger from your laptop, remove the battery from the laptop and leave it out for like 10mins and put it back in and reboot the laptop. This should not cause side effects but still contact your OEM to make sure that nothing else is needed after leaving the battery out for extended period of time. Keep me posted.
Post relates to: Treo 650 (Unlocked GSM) -
When I Hotsync Bluetooth connection is successful, then in step 2, "Connecting with the desktop" Hotsync errors out with message "The connection between your device and the desktop could not be establisthed. Please check your setup and try again."
Bluetooth configuration inticates Bluetooth serial port COM Port is set to COM3
Hotsync setup: when I click "Local" tab I get error message "The selected port, COM5, is not available at this time. HotSync Manager will open the port when it becomes available."
Hotsync setup > "Local" tab > Serial Port dropdown shows only COM4. I cannot change it to anything else.
Note: I can send files to PC using Bluetooth just fine; error only occurs when I Hotsync using Bluetooth connection.
Tried rebooting both laptop and Palm TX. Still can't Hotsync.
Operating system: Windows XP Pro
Post relates to: Palm TXYou are not the only one having this problem. I have REPEATEDLY tried to bluetooth sync with my new toshiba windows 7
Palm 6.2.2 to no avail. I have tried every bluetooth device they suggest and every "fix" or "solution" that has been offered here and in on line chat with a Palm tech. No dice! I even took my computer and all components to a tech. He worked on it for 5 hours. Every once in a while for no apparent reason it will magically sync, but never consistently. Using 32bit on my husband's computer with Vista, and the docking cradle still works so I have my data. A few others have apparently had success with this problem but I think it is an accident that it works for them when it does. Otherwise it would work for everyone. We have read everything we can find and spent literally hours and hours and hours.
I am now in the process of trying to import/export to Outlook and plan to upgrade to another device like iPhone or blackberry that will sync data with Outlook. My Palm TX also has not been able to successfully sync with that although, as I said earlier, it syncs with Palm Desktop. Good luck with your's. -
Setup 1941 router with cable modem and 2 vlan?
hello everyone,
i need a little help setting up my new 1941 router with cable modem using 2 vlns.
this is what i have:
1- 1941 router configured as g0/0 wan port facing isp configured as (dhcp). g0/1 is lan facing the switch (192.168.1.1)
dhcp pool (192.168.1.x)
2- sg300-28pp switch.
3- wap371 AP/ 11pcs..
now everything is working perfect except sometimes we have more than 250 to 300 people trying to connect to the wifi, the router will have no enough ip addresses.
i heard that i can setup 2 vlans to solve this problem? and is there any setup that i have to do on switch and Access points?
please i will appreciate any little help
Regardshello Andre Neethling i added network 192.168.0.0 255.255.254.0 to dhcp pool config and it seems that it is working but i am concern that i am going to have problem in the future so please take a look at the running config and let me know if i have everything done right. also we want to order static ip address from the provider for our security camera system and we will not longer receive dhcp ip from them and my router setup is to receive it as dhcp on g0/0 so what i should do about changing the settings on g0/0?
i appreciate your help
Building configuration...
Current configuration : 1163 bytes
! Last configuration change at 00:46:35 UTC Wed Apr 15 2015
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Abdullah
boot-start-marker
boot-end-marker
no aaa new-model
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp pool Local
import all
network 192.168.0.0 255.255.254.0
default-router 192.168.1.1
multilink bundle-name authenticated
license udi pid CISCO1941/K9 sn FTX1523022E
redundancy
interface GigabitEthernet0/0
ip address dhcp
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 101 interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
access-list 101 permit ip 192.168.1.0 0.0.0.255 any
control-plane
line con 0
line aux 0
line vty 0 4
login
scheduler allocate 20000 1000
end -
Connection between lightweight access point and switch?
Hello everybody,
I am a bit confused about cisco 1000 series access point connection. On wireless lan controller and lightweight access point basic configuration example document id 69719 (http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml), I understood the access point has two vlans associated with (vlan 3 and 4). Am I correct?
Why is connection between access point and catalyst port just access port rather 802.1q trunk? How vlan traffic can traverse from the access point to controller?
Please advice.
Many thanks,
NitassNitass,
The AP itself does not need to be a trunked port, but the uplink to the controller does. When using a Lightweight enviroment, all the traffic passes thru an encrypted LWAPP tunnel from the AP to the controller, and then gets sent out the correct VLAN interface on the controller. -
I am about to hook up my airport extreme. My cable modem goes into a router, and one of those ports will supply my airport extreme. I was told by the Apple Store that I would need to configure my airport extreme as a wirreless access point. How do I do this?
With sbcgobal I got a Gateway 2wire modem. What I would like to know is how do I set up my APE as remote?
Unfortunately, you won't be able to do this as few non-AirPort routers will work with AirPorts in a Wireless Distribution System (WDS). -
Trouble connecting Cisco router with cable modem for Internet purposes
So I am requesting help from the Cisco community on this issue as the cable company states there equipment is working fine. At all my facilities I have a guest Internet service setup through a local Internet provide to provide Internet services to the residents and guests. I have the cable modem usually a Motorola SBG6580 or a SMC 8014 (both provided by cable company) connected to my router on a FE or GE interface. I am using static IPs and using the cable modem just as a modem (bridge mode). Over the past several months these connections have just stopped working. I have not made any drastic changes to my router configs; however, the cable company has updated the firmware on these modems. I am wondering if that could affected how the modem and router talk. I was told by the cable company that the modem sees the Cisco router but that the port is inactive. My router shows the port is active and traffic passing. Does anyone have any ideas that could point where the problem lies? I will post a basic config to one that currently does not work. I am using a VRF to route a certain group out, using NAT. Please let me know if I need to post additional info. Any help would be greatly appreciated.
Cisco CISCO2911/K9
Version 15.2(3)T1
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1204RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-3.T.bin
boot-end-marker
card type t1 0 0
logging buffered 64000
aaa new-model
aaa session-id common
clock timezone cst -6 0
clock summer-time CDT recurring
no ipv6 cef
no ip source-route
ip vrf 5
rd 5:1
ip multicast-routing
1
ip dhcp pool Guest
vrf 5
network 10.51.XXX.0 255.255.255.0
default-router 10.51.XXX.XXX
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
multilink bundle-name authenticated
application
global
service alternate default
license udi pid CISCO2911/K9 sn FTX1508AHTM
hw-module pvdm 0/0
redundancy
ip tcp synwait-time 10
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding 5
ip address 10.51.xx.xxx 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/2
description Guest Intenet access
ip vrf forwarding 5
ip address 24.242.182.182 255.255.255.252 <--Cable company IP, Modem IP is 24.242.182.181
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
no ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 9 interface GigabitEthernet0/2 vrf 5 overload
ip route vrf 5 0.0.0.0 0.0.0.0 24.242.182.181
access-list 9 permit 10.51.204.0 0.0.0.255Ok, mysteriously this location just started working yesterday, but I still am dealing with seven others and I really would like to know what is going on. I will give you everything you may need and let me know.
Config:
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1112RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-1.T.bin
boot-end-marker
aaa new-model
aaa session-id common
clock timezone CDT -6 0
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
no ip source-route
ip vrf GuestVRF
rd 5:1
ip multicast-routing
ip dhcp pool Guest
vrf GuestVRF
network 10.51.112.0 255.255.255.0
default-router 10.51.112.1
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
application
global
service alternate default
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding GuestVRF
ip address 10.51.112.1 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
description Guest Internet (Time Warner Connection)
ip vrf forwarding GuestVRF
ip address 97.77.116.234 255.255.255.252
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
ip nat inside source list 5 interface GigabitEthernet0/1 vrf GuestVRF overload
ip route vrf GuestVRF 0.0.0.0 0.0.0.0 97.77.116.233
access-list 5 permit 10.51.112.0 0.0.0.255
control-plane
end
router#sh ip arp vrf GuestVRF
router#Internet 97.77.116.233 2 f80b.bee7.e09f ARPA GigabitEthernet0/1
Protocol Address Age (min) Hardware Addr Type Interface
Internet 97.77.116.234 - 8843.e13c.8d99 ARPA GigabitEthernet0/1
router#ping vrf GuestVRF 97.77.116.233
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 97.77.116.233, timeout is 2 seconds:
Success rate is 0 percent (0/5)
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:10
Input queue: 76/75/15/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
81 packets input, 4860 bytes, 0 no buffer
Received 81 broadcasts (0 IP multicasts)
0 runts, 0 giants, 12 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
16 packets output, 1193 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:42
Input queue: 76/75/67/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 1000 bits/sec, 2 packets/sec
408 packets input, 24480 bytes, 0 no buffer
Received 408 broadcasts (0 IP multicasts)
0 runts, 0 giants, 61 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
72 packets output, 5669 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
I am receiving packets in and out of the interface but I cannot ping the modem through the VRF.
router#sh ip nat translations
Pro Inside global Inside local Outside local Outside global
udp 97.77.116.234:3169 10.51.112.39:3169 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:8534 10.51.112.39:8534 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:12244 10.51.112.39:12244 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:14002 10.51.112.39:14002 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:23623 10.51.112.39:23623 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:24489 10.51.112.39:24489 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:24550 10.51.112.39:24550 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:27458 10.51.112.39:27458 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:28603 10.51.112.39:28603 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:37404 10.51.112.39:37404 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:53942 10.51.112.39:53942 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:58125 10.51.112.39:58125 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:64797 10.51.112.39:64797 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:62342 10.51.112.52:62342 209.18.47.62:53 209.18.47.62:53
tcp 97.77.116.234:36559 10.51.112.69:36559 199.167.177.46:1227 199.167.177.46:1227
tcp 97.77.116.234:48895 10.51.112.69:48895 54.195.253.126:5223 54.195.253.126:5223
tcp 97.77.116.234:58385 10.51.112.69:58385 54.195.243.137:5223 54.195.243.137:5223
Pro Inside global Inside local Outside local Outside global
tcp 97.77.116.234:58658 10.51.112.71:58658 31.13.66.165:443 31.13.66.165:443
udp 97.77.116.234:3066 10.51.112.72:3066 209.18.47.62:53 209.18.47.62:53
udp 97.77.116.234:3884 10.51.112.72:3884 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:6656 10.51.112.72:6656 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:11194 10.51.112.72:11194 209.18.47.61:53 209.18.47.61:53
udp 97.77.116.234:11774 10.51.112.72:11774 209.18.47.62:53 209.18.47.62:53
Let me know if you need anything else. I need to figure this out and I just don't get it because the other site wasn't working a few days ago and all of a sudden it is working again but others are still not. -
Suddenly I cannot stream video on my iPad 2. I get the error, "The operation cannot be completed." The browser (Safari or Chrome) continues to try to load the video with no result. I have no problem streaming on my WIndows PC (laptop) using the same WiFi router (Netgear dual band) connected to my Comcast/Xfinity cable modem. I have tried renewing my lease, clearing apps out of memory and rebootng the iPad, still no luck. (How do you do a "hard reset", I forgot?) Frustrating since I don't own a TV and am an Al Jazeera addict! Help!
Suddenly I cannot stream video on my iPad 2. I get the error, "The operation cannot be completed." The browser (Safari or Chrome) continues to try to load the video with no result. I have no problem streaming on my WIndows PC (laptop) using the same WiFi router (Netgear dual band) connected to my Comcast/Xfinity cable modem. I have tried renewing my lease, clearing apps out of memory and rebootng the iPad, still no luck. (How do you do a "hard reset", I forgot?) Frustrating since I don't own a TV and am an Al Jazeera addict! Help!
-
Have had my Tungsten E2 for 3 years...I always use cable to Hotsync, and the last few weeks it has worked only intermittently. Either the device is not recognized, or it starts the HotSync and then freezes. I have checked out various online suggestions but then discovered that the only thing that seems to work is to exit Hot Sync Manager, then restart it again each time - then Hot Sync seems to work fine - a temporary solution! I don't have Bluetooth capabilities. I can't figure out if I need a new cable, a new OS (have Vista), a new laptop (only 2 years old) or a new Palm! Any suggestions? Thanks!
Post relates to: Tungsten E2Hello!
The next time that happens, USB device not recognized error, unplug the cable from the PDA and pc, then soft reset the device, then plug the PDA back in and see wat happens.
Post relates to: Treo 650 (Unlocked GSM) -
How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.
The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network. -
HP photosmart 7520 connects to wrong access point and looses connection
I recently installed a remote wireless access point in an outbuilding. I'm using a router with the same SSID and password as my main router with the same security settings. Only the main router is set to issue IP addresses. The system works fine with two laptops, a desktop, an Ipad and an Ipod. It provides continuous connections from my house to the outbuilding. Only the HP Photosmart seems to be an issue. At first the system worked fine then after a couple of days it lost its connection. I tried to the Wireless Setup Wizzard with no success. The Wireless Network Test results indicated that MAC address filtering may be enabled. This is not the case, MAC filtering in not enabled on either router. The next morning the printer was fine and connected again. I suspect that it is detecting the remote router and trying to connect through it. During the setup a warning came up indicating that two routers were detected with the same SSID and Password and that the printer might try to connect to the wrong router. It should not matter since the remote router connects and is issued IP addresses through the main router. The only difference in the routers is the BSSID. This uses the same number as the MAC filtering address, so I suspect this may be the problem. Any suggestions on a work around. The only thing I have found that solves the problem is turning off the remote router.
Hello there -
Is it possible your new remote access point only supports the 5Ghz band for N connection, or that it's connected to your primary router through a wireless N connection in the 5Ghz band? The 7520 only supports 2.4Ghz N connections. If your primary access point supports both 2.4Ghz and 5Ghz, that is likely why it's able to connect there while it cannot connect to the new access point. Many newer laptops and iPad/pods utilize 5Ghz N, which would explain why they can connect and your 7520 cannot. I'd recommend moving the 7520 closer to the primary router and using AirPrint to send your jobs.
***I am an HP employee***
The comments above represent myself and do not reflect the opinions of HP. -
Forgetting WiFi password, and not connecting to wireless access point automatically??
I'm using (until tomorrow when I get a MacBook Pro which HOPEFULLY won't have the same problem) a pre 2007 Macbook which is running Mac OS X 10.5.8. It was previously owned by my brother and passed onto me about 4 months ago. Within that time I've had nothing but problems with the WiFi connection!
The first issue would have to be that if I put the MacBook to "sleep" rather than turning off, it disconnects from WiFi during that process. Fine, that's to be expected. But when I wake it up, it's not only disconnected, but I have to re-enter my WiFi password in order to reconnect. Is there some reason that it will not remember the password through this sleep process? Turning off and on normally works fine, and it connects automatically, but not when it sleeps.
The second problem is equally confusing to my mind. In my house, we have a wireless access point upstairs (we have 3 floors after having our attic converted). All characteristics (name, password etc) are the same on the access point as on the main router downstairs. Every device in our house, included a couple of android phones, a tablet, and two laptops running various versions of Windows, all connect to this wireless access point with no problem at all. None of them have been "set up" to do so, in that they detect it as part of the same network and join it automatically. But for some reason, my MacBook won't do it? At first I would assume that perhaps it's due to the age of my MacBook and maybe some flaw in the old operation system, but my iPhone 4S running iOS 7 doesn't connect to this access point either. Is this some weird security thing that Apple use in their devices??
To make things even more frustrating, the MacBook's issue of remembering the WiFi password means that when I come back downstairs and into range of the main router, it's forgotten the password again and I have to re-enter it to reconnect.
Can some PLEASE offer some kind of assistance? I'm getting a brand new MacBook Pro tomorrow and if it's an OS issue then I assume I won't have it anymore, but I'm desperate to solve this issue one way or another considering this machine will be staying in the family and in this house so will pressumably have the same issues.
Thanks in advance guys! If I've not given enough info, just askI'm using (until tomorrow when I get a MacBook Pro which HOPEFULLY won't have the same problem) a pre 2007 Macbook which is running Mac OS X 10.5.8. It was previously owned by my brother and passed onto me about 4 months ago. Within that time I've had nothing but problems with the WiFi connection!
The first issue would have to be that if I put the MacBook to "sleep" rather than turning off, it disconnects from WiFi during that process. Fine, that's to be expected. But when I wake it up, it's not only disconnected, but I have to re-enter my WiFi password in order to reconnect. Is there some reason that it will not remember the password through this sleep process? Turning off and on normally works fine, and it connects automatically, but not when it sleeps.
The second problem is equally confusing to my mind. In my house, we have a wireless access point upstairs (we have 3 floors after having our attic converted). All characteristics (name, password etc) are the same on the access point as on the main router downstairs. Every device in our house, included a couple of android phones, a tablet, and two laptops running various versions of Windows, all connect to this wireless access point with no problem at all. None of them have been "set up" to do so, in that they detect it as part of the same network and join it automatically. But for some reason, my MacBook won't do it? At first I would assume that perhaps it's due to the age of my MacBook and maybe some flaw in the old operation system, but my iPhone 4S running iOS 7 doesn't connect to this access point either. Is this some weird security thing that Apple use in their devices??
To make things even more frustrating, the MacBook's issue of remembering the WiFi password means that when I come back downstairs and into range of the main router, it's forgotten the password again and I have to re-enter it to reconnect.
Can some PLEASE offer some kind of assistance? I'm getting a brand new MacBook Pro tomorrow and if it's an OS issue then I assume I won't have it anymore, but I'm desperate to solve this issue one way or another considering this machine will be staying in the family and in this house so will pressumably have the same issues.
Thanks in advance guys! If I've not given enough info, just ask -
Help with using the WRT54G as an Access Point
Ever since I've been using the WRT54G as an access point behind another router I have been experiencing intermittent disconnects and reconnects from the internet anywhere from once every 5 to 60 minutes. I get the message notifcation that the Local Area Network is disconnected for a split second before everything reconnects and works fine. This has been happening on my desktop which is wired directly to the WRT54G which itself is wired directly to the other router, but I have also experienced these disconnects with my iPhone and laptops which have been using the wireless signal.
When I was connected directly to the original router I hadn't experienced any of these problems. I've also tried changing settings and even disabling the wireless broadcast of the WRT54G but to no avail. I can't figure out what the issue is, but it seems to also be affecting the wireless broadcast of the original router.
I've updated firmware for the Linksys, and I've done a reset for the Linksys as well.
Any help would be much appreciated to get rid of these disconnects.OK, so I've tried a different setting to see if it'll work.
Previously I had not configured the WAN of the Linksys router at all and left it on Auto (DHCP) even though I disabled the DHCP for the LAN. I've now set the WAN up to a random Static IP and hopefully this will solve the problem, but I'm not sure as of yet, if anyone could look over the settings to see if they're correct please let me know.
Router 1- (Router)
WAN - Configured to ISP
LAN - DHCP
IP: 192.168.1.1
Subnet: 255.255.255.0
IP Range: 192.168.1.100 - 192.168.1.150
Router 2 - Linksys (AP)
WAN - Static IP
IP: 64.XXX.XXX.1 (made up value)
Subnet: 255.255.255.0
Gateway: 64.XXX.XXX.254 (made up value)
DNS: XX.XXX.XXX.X (made up value)
LAN - DHCP disabled
IP: 192.168.1.2
Subnet: 255.255.255.252
The WRT54G was a bit of a pain in terms of what Static IP and Gateway values they would accept, so I had to randomly put in values until I found something that worked. So far no disconnects, but it's only been half an hour. I can't seem to access the admin page for my Linksys router at 192.168.1.2 anymore though.
Maybe you are looking for
-
Windows 7 Pro recovery DVD for T420 laptop?
Can you get a recovery DVD from Lenovo for the T420 laptop. I created the recovery media, and then had the OS remove the recovery partition after the creation of the discs. I just found that there is a problem with the disc and can't restore the sys
-
let me know what i can do to find out.
-
LARGE SOFTBOOK Q's: A) Die Cut window cover? B) Spreads?
Couple of Q's for you brilliant boards people, anyone kno the answers to... A) "LARGE SOFTCOVER BOOK (NO COVER DIECUT?) (size 8.5 x 11, price $19.99) seems is only offered with a die-cut square window. Is there any option to ditch this in favor of a
-
Well although I didn't delete folder named Recovered files once in week that folder is in my trash. Is that normal process or something is wrong?
-
Hello everyone, How to achieve joins in EJB? Thanks in advance