The display on my ipod touch is permanently zoomed. what did I do and how to fix it?
the display on my ipod touch is permanently zoomed. what did I do and how to fix it?
See:
iPhone and iPod touch: Home screen icons are magnified or large
Similar Messages
-
Hello, alot of my space taken up on my ipod nano is listed under (other) I don't know what this is but it sure takes up most of the space on my ipod. Does anyone know what (Other) refers to and how to remove it.?Thx
Hello Norman,
Welcome to the Apple Support Communities. To find out what the Other section is on your iPod Nano, the following will explain what the Other section is all about.
Understanding capacity on iPhone, iPad, and iPod
http://support.apple.com/kb/HT1867
Once that is complete, then check the appropriate sections to see what is there. If you cannot isolate the issue then you may need to restore the iPod Nano. The following will assist with the restore process.
Restoring iPod to factory settings
http://support.apple.com/kb/HT1339
Regards,
-Norm G. -
When using a blutooth headset with my ipod touch the signal seems to cut in and out. The controls seem to work fine but the audio cuts out when the unit is moved or placed in my pocket.
Could be interference
AirPort and Bluetooth: Potential sources of wireless interference
Try:
- Reseting the BT headset
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset network settings: Settings>General>Reset>Reset Network Settings. You will have to rejoin all wifi networs and re-pair all BT devices -
The screen on my ipod touch is stuck zoomed in. I don't know how it happened I just looked down and it was like that. I have turned it off and back and even reset it but it still keeps zooming back in each time I turn it on. I can't unlock it because I can't see the numbers and it won't let me move around the screen. Please help.
This is asked and answered often. The foru search bar is on the right side of this page.
It is also covered in the manual - zoom feature:
iPod touch User Guide (For iOS 4.3 Software)
Double tap with three fingers. -
When I plug my ipod touch into the pc, it tells me:the ipod cannot be used because the apple mobile device service is not started. What does this mean and how do I get rid of that and enable syncing?
Hello Julia,
Start with this article.
http://support.apple.com/kb/ts1567
B-rock -
I have 100 songs on i pod touch. But when i connect it to itunes it only showed 44 songs. What is actually happening and how to fix the problem so that all music in my iphone can be seen in my itune
If they are iTunes purchased music then go to Settings>iTunes and App Store and turn off Show All.
Next
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync/delete all music and resync
To delete all music go to Settings>General>Usage>Storage>Music>Tap edit in upper right and then tap the minus sign by All Music
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device. -
I just got a notice to update my firefox to 4.0 and when I downloaded the new software it indicated: that I can't open the application "Firefox" because it is not supported on this architecture. Any ideas about what might be wrong and how to fix it?
Firefox 4 requires at least OS X 10.5 and an Intel Mac. There is a third party version of Firefox 4 that runs on OS X 10.4/10.5 and PPC Macs, for details see http://www.floodgap.com/software/tenfourfox
If you prefer, you can get the latest version of Firefox 3.6 from http://www.mozilla.com/en-US/firefox/all-older.html -
My iTunes background has gone gray and black. What did I do and how do I fix the issue?
My iTunes background has gone gray and black. What did I do and how do I fix the issue?
Had the same problem. Go to Users/Library/Preferences. Discard every file that begins with com.apple.iTunes...
-
Firefox is refusing to start. It says that my profile is missing, which it appears to be. Yet the way in which one goes about creating a new profile wont' work either. Anybody have a bloody clue what's going on and how to fix it?
AIR give you classes to detect an on-line or off-line status, it's in
this way for the sake of flexibility for instance what happens if you
only what to sync data only on Saturdays at 2 am? If it were done
automatically that'll be a problem. And it isn't so complicated.
You can download the SalesBuilder from AIR examples at www.adobe.com/devnet/air
it's an application that does everything you have in mind.
I don't understand your question abou file types.
An AIR app can communicate with almost every backend served tech
CF, .Net, PHP, RoR.
Sincerely,
Michael
El 14/05/2009, a las 8:48, IrishAIRMax <[email protected]> escribió:
>
I have to say that I'm loving the picture! well cool!
>
Sorry but I don't quiet understand. I thought AIR did the updating
automatically? I didn't realise the developer had to program the
logic of how the updates take place? Is it a case in most AIR apps
that when online the app updates the server and once every intervel
(of however long) the local SQLite DB is synced to the more updated
server DB. Then when offline the developer has to sense that the app
is offline and store a log manually of the updates without any help
from AIR itself, and then update once it comes online again?
>
Can AIR link to anything more than a database on the server side
apart from webservices, for example .as files or any other file types?
>
What type of server is a Flex app stored on, is it a specific Adobe
server rather than a Java or .NET server?
>
Thank you so much for your last comment!
IrishAIRMax
> -
The screen resolution in 1920x1200 dropped on my MacBook Pro 17". Seems like I have not the same pixels. There are also vertical, thin lines on the screen. Makes the screen look milky. Anybody knows what's going on and how to fix it?
Take it to an Apple Store or other service provider for testing.
-
When converting a .pptx file of 6MB to .pdf, the file size ballooned to 25MB. The original file was created on a PC. What happened? Why? How to fix? Thx.
gssharpe wrote:
What happened?
Nothing much. Different formats.
How to fix?
Try editing the original file. Resample pics to a lower resolution, check out other graphics, check table borders (eliminate any dotted lines or borders), check font usage. When generating PDF, try Save As (instead of Print > Save As), although I don't expect that'll make much difference.
Next, open the PDF in Preview, choose File > Save As, choose Format: PDF, Quartz Filterz: Reduce File Size. If that isn't enough, you can use ColorSync Utility to duplicate the Reduce File Size filter, and then edit it for a more aggressive size reduction. But keep in mind that size reduction means lower quality. -
on my iPad, my outgoing mail regularly replies that the email was rejected by the server because it does not allow relaying. What does that mean and how can I make the emails go out?
Try this.
Check your username and password in the outgoing mail server setting. Fill it in even of it says that it's optional.
Settings>Mail, Contacts, Calendars>choose the email account>account name, tap on SMTP (under the 'Outgoing Mail Server' heading) and then tap on your Primary Server and try entering your email username and password and see if that works for you. -
When I try to set up my time capsule it says that the PPPoE Server is not found... What does this mean and how do I fix it? Thanks !
You are using PPPoE but there is no server to authenticate against.. or the modem is already connected and nothing else can join.
Is this ADSL?
Do you have the modem in bridge?
How does it work with the modem working as router? ie what type of connection does your ISP supply.. eg PPPoE is only one.. PPPoA is another.. IPoA or ETHoA.. and sever other more specialised.. PPPoE can only work where it is supported. -
I don't know much about computers can anyone walk me through this ? How Do I Change The Software Update Server Address On A Client ? what do I open and how do i put it in the right spot?
The simplest method is to run a defaults command on the client Macs (easily pushed via Apple Remote Desktop):
defaults write com.apple.SoftwareUpdate CatalogURL 'HTTP_URL_FOR_CATALOG'
for a user. If you run it via sudo it will set it for whenever you use softwareupdate as root.
The HTTP_URL_FOR_CATALOG has been changed with Mac OS X 10.6. If you use MCX it will automatically pick the new catalog – however if doing it manually the following URLs need to be used for whichever client version is in question:
Mac OS X 10.4: http://mysus.example.com:8088/index.sucatalog
Mac OS X 10.5: http://mysus.example.com:8088/index-leopard.merged-1.sucatalog.sucatalog
Mac OS X 10.6: http://mysus.example.com:8088/index-leopard-snowleopard.merged-1.sucatalog
Mac OS X 10.7: http://mysus.example.com:8088/index-lion-snowleopard-leopard.merged-1.sucatalog
Mac OS X 10.8: index-mountainlion-lion-snowleopard-leopard.merged-1.sucatalog
To double check this applied you can run the following command:
/usr/libexec/PlistBuddy -c Print /Library/Preferences/com.apple.SoftwareUpdate.plist
and /usr/libexec/PlistBuddy -c Print ~/Library/Preferences/com.apple.SoftwareUpdate.plist
to see what settings are for the computer and user appropriately.
If this is working correctly when running Software Update (GUI) you should see the server address appear in parenthesis in the title of the window.
MCX
Another alternative is to use Workgroup Manager to manage the preferences via MCX from your server. This can be done for users, or for computers if they are bound to your Open Directory.
If you are using 10.5 Server or newer: you can simply use the Software Update section under Preferences.
Manually:
Choose the accounts, computers, or groups to have the preference applied to.
Click on Preferences, and then the Details tab
Press the Add… button and navigate to /Library/Preferences/com.apple.SoftwareUpdate.plist
Press Edit…
Under Often, add a New Key and enter the name CatalogURL
Make sure the type is string and then enter your SUS URL (eg. http://mysus.example.com:8088/index.sucatalog or if using 10.6: http://mysus.examle.com:8088/ – see above from the defaults section)
Press Apply Now, then Done. Once users/computers have refreshed their MCX settings (usually the next login or restart) the new settings will take over.
If this is working correctly when running Software Update (GUI) you should see the server address appear in parenthesis in the title of the window.
In order to have a system-wide configuration one has to run the following:
sudo defaults write /Library/Preferences/com.apple.SoftwareUpdate CatalogURL "http://your.updates-server.lan:8088/index.sucatalog"
In order to correctly work both on Leopard and Snow Leopard the right command to issue is:
defaults write /Library/Preferences/com.apple.SoftwareUpdate CatalogURL "http://your.updates-server.lan:8088/index-leopard-snowleopard.merged-1.sucatalog"
Happily used and tested on my network
The DNS trick that Chealion points out is fantastic. I use it at our office, and every computer on our LAN will automatically pull the updates from the local repository at high speed without any configuration.
Create the swscan.apple.com DNS zone on your internal DNS server, and have it resolve via an A record to your Mac
Tags: automaticupdates mac clients macosx setting as default software update
Category: Serverfault
Share
0
0
Google +
0
0
0
5
You might also like:
Can I Update My Jb 4s To 6.1.2 Without Restore? Tue. Jan 21st, 2014
Iphone 4 Not Charging After Update To IOS6
IPad 2 Not Updating To IOS 5.1
How To Resolve The â€âunable To Install Update†Error For OTA IOS Updates?
What Is â€âSoftware Update†Doing When It Says â€âChecking For New Softwareâ€?
Advertisement
Comment
- See more at: http://www.eonlinegratis.com/2013/how-do-i-change-the-software-update-server-add ress-on-a-client-mac-to-use-my-own-server/#sthash.YhHp5zWk.dpuf -
a lock logo with an arrow encircling it has appeared besides the battery percentage symbol in my iphone 4s. What does that mean and how to get rid of it ?
Its the screen orientation lock, and is covered in the User Guide.
Double-tap the home button, swipe to the right on the dock area and tap the left-most icon.
Maybe you are looking for
-
Photoshop CC(2014) is having "redraw" or video driver/GPU issues
Since upgrading my Mac to OS X 10.10 (Yosemite), after a working on a file or two, my photoshop image window looks like this: This is a JPG, after I have opened a RAW file, with Camera Raw 8.7 beta (happened before the Camera Raw update), and make my
-
Missing TV season after downloading all 6 seasons
Hi all, I recently downloaded a TV series that has 6 seasons. All seasons are in my Itunes except season 3. when I go to the Itunes page where I purchased it, and it says I already purchased it. Where do I locarte the missing season and where can I r
-
When clicking on a link in an email, an error message kept coming up, implying an incombatibility .
When clicking on a link in an email, an error message kept coming up, implying an incombatibility . Please advise me what version of acrobat reader is compatible with Windows Vista.
-
URGENT please: I get a "Shared Technologies" error on installing Photoshop Elements 11
On my Windows 7 64-bit system, I get a "Shared Technologies" error on installing Photoshop Elements 11.
-
Aliasing issues in ACR 6.4 output, jagged edges
In images with high frequency detail, aliasing occurs that is most visible in diagonal directions. These jagged edges are noticable in the output, and obviously get worse in enlargements which is also the main reason I post this. To date, I've found