The ethernet cable keeps slipping out of its slot

I have a G72 notebook. the ethernet cable keeps slipping out of notebook's slot. It began infrequently, then often and now I have to hold it in or I can't get on intyernet. What a crawl! when I called tech  I was told by tech to buy another cable. I've bought 2 more & same problem. What must I do to get my notebook back? thanks mucho

Hi,
You bought 2 new cables and still have the problem, the only thing I can think of is the LAN port itself. Do you have friends, relatives ...just bring those cables and plug to their machines to see, and also physically check the LAN ports to see any difference.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

  • Ethernet cable keeps popping out of socket.

    I posted this on another forum, not having seen this one which I hope is more relevant. My thick yellow Ethernet cable won't stay in and it is driving me mad. Where does the fault lie? Is it just a problem with these cables you have to put up with.

    Hi,
    Ethernet cables have a little sprung clip on the end. Perhaps yours has broken off.
    Probably a new cable will fix it.
    Merry Christmas from England,
    alan

  • Do I need the ethernet cable anymore?

    I recently discovered that my DSL modem and Internet plan supports WI-FI, so I can access the Internet throughout the house. When I bring my iMac to another room, it can, of course, access the Web wirelessly.
    When I bring the iMac back to the original room, I re-plug the ethernet cable back in, but the question arises as to whether I even need it anymore.
    Is this necessary? Are there still advantages to having the Mac plugged in directly to the Internet or can I safely eliminate an extra piece of cable clutter by removing this cord?

    I for one, keep my iMac plugged into the ethernet.  I am not lugging that thing all over the house just to get free wifi.
    When I first got my iMac I used wifi for about a month until I noticed all of my connected "devices" started getting funky.  After plugging my iMac to the ethernet all my "devices" were happy campers. 

  • HT1941 trying to connect time  apsule to macbook air with the ethernet cable in the WAN port the airport utility doesn't detect it

    trying to connect time  capsule to macbook air with the ethernet cable in the WAN port but the airport utility doesn't detect it but when i put it in the LAN one it does but it doesn't let me configure
    any ideas?

    Isn't it fun trying to do things without an ethernet cable direct to the computer.. Apple sell a usb to ethernet adapter cable fairly cheap.. makes life a lot easier having something to do hard connections.. or as hard as usb can manage.
    Since you have to access the TC by wireless .. press and hold the reset button on the TC for about 10sec until front led flashes rapidly.. don't worry about the ethernet cable.. leave it disconnected.
    Now click on the airport symbol and join another network. The TC should revert to its home name.. which will be a combo of Time Capsule and its MAC address. There is no wireless security and you can do the setup.

  • Having trouble with the ethernet cable

    Hello-
    All of the sudden the ethernet cable I have been using for my MacBook Pro seems to be causing trouble with my streaming, especially when watching live online streams like from CBS New.com, MSNBC, etc. I had not had any trouble until recently but when I push the ethernet cable in a little bit the stream seems to pick up. This also did happen the last time I installed the latest Flash update. When I do the Software Update, it goes OK, it just seems to be the live video streams.
    I thought I would get a new ethernet cable since I do not know how to hook up my Airport Extreme with the odd set up where I am staying.
    Is there a better kind of ethernet cable or does it matter what kind I get? any recommendations on a good ethernet cable (brand) I should try?
    I would uninstall the latest Flash update, but every time I mess around with Flash it causes trouble, but not the kind of trouble I am having now.

    CanaDuke wrote:
    Moved the AEBS (g) downstairs
    That's probably what caused your problems.
    Here are my questions:
    1) Would replacing the AEBS (g) with an Express (n) solve the problem?
    No.
    The weakness is in the connection between the main base station and the remote (in this case the AEBS (g).
    If you got an Airport Express 802.11n, it would improve the connectivity if it operated in 802.11n mode. However as you have none-802.11n devices which use wireless (ie the iPhones) then you would need to operate in 802.11g mode and therefore the weakness would still be there.
    2) Would ADDING an Express (n) be better?
    See above.
    If everything was 802.11n then yes, otherwise no.
    3) Would we be better off buying the wireless adapter for the xbox, rather than plugging it in with ethernet?
    If you moved the AEBS back to its original location then I expect yes it would.
    iFelix

  • I have just got an Airport time Capsule for back up how do I do it? Do I put the ethernet cable into the back of my sky hub because when I do that the amber light on my Time Capsule flashes amber. Please talk in simple terms as I am a

    I have just got an Apple Airport time capsule to back up my one year old iMac......how do I do it? I have tried putting an ethernet cable into the time capsule and to my sky hub, all I get is a flashing amber light, can anyone help I am a silver surfer not used to Apple products, but love them, plus I don't understand half of the jargon....HELP please

    Apple's Setup Guide for the Time Capsule is pretty simple and clear for most users, and you don't indicate at what point or step that you are getting stuck.
    So, please go to page 8 in your Setup Guide to review the topic of Plugging In Your AirPort Time Capsule.
    The Sky hub will likely have 4 Ethernet <--> ports on the back of the device. Pick any one that you want and connect one end of the Ethernet cable to the port that you choose.
    Then, connect the other end of the Ethernet cable to the WAN (circle of dots) port as shown in the Setup Guide.
    Continuing with the instructions on page 8 of the Setup Guide, power up the Time Capsule by connecting the power cord from the back of the Time Capsule to a wall AC jack.
    Note that the instructions indicate that the indicator light will be solid amber during startup, and it will change to blinking amber during the setup. The light will remain blinking amber until you have configured the Time Capsule at which time the light will turn green.
    Next, go to page 12 of the Setup Guide to see the information to Use your Mac or iOS device to set up your AirPort Time Capsule.
    You indicated in your tag line that you were using OS X Mountain Lion (10.8.3), and since that will exceed the minimum requirement of a Mac using OS X (10.7.5) as noted in the guide, you can use your Mac to set up the Time Capsule.
    Continuing with the instructions on page 12 of the Setup Guide......
    1. Open AirPort Utility on your Mac.  It is located as follows:  Finder (the smiley face on the dock) > Applications > Utilities > AirPort Utility
    2. Select your AirPort Time Capsule and click Continue. You won't be able to do this, but read further......If you do not see the AirPort Time Capsule that you want to configure, choose it from the WiFi status menu in the menu bar, at the top of the screen.
    So, clicking on the WiFi icon will yield a small window that looks like this:
    The example below shows an AirPort Extreme.  You will see Time Capsule on your screen. Click on Time Capsule.
    When you click on Time Capsule, that will get the setup wizard going. it will take a minute to analyze the network, then display a screen that looks similar to the illustration below, except that you will see a picture of a Time Capsule on your screen
    3. Continuing with the Setup Guide.......Follow the onscreen prompts to create a new network
    Network Name...........Type in a simple name that you want to call your network. Do not use the suggested name.
    Base Station Name....Type in a simple name that you want to call the Time Capsule.  Mine is TC, for example.
    Password...................Type in a password that will be used for both the network and the Time Capsule.  Write that down.
    Verify..........................Type in the password again to Verify
    Click Next
    The setup wizard will configure everything for you. When you see the message of Setup  Complete, click Done.
    The Time Capsule is now set up and it will display a green light.

  • My A'Extreme sometimes won't connect to my MacBook Pro even if I have a green light on the device . I can unplug the ethernet cable and reconnect and it will work fine. all diagnostics say there is nothing wrong. Any ideas ?

    My A'Extreme sometimes won't connect to my MacBook Pro even if I have a green light on the device . I can unplug the ethernet cable and reconnect and it will work fine. all diagnostics say there is nothing wrong. Any ideas ?

    This is more about your modem then anything. Sometimes you'll need to unplug and plug back in your modem. Consider it a glitch from the ISP or just the modem in general.
    when I need to turn something off then on I try the modem first. This when I'm not doing any ware and tare to the device.

  • Is there an easy way to switch between ehternet and wifi connection without having to disconnect the ethernet cable?

    Hi All
    Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable. The reason I ask is that I find it quicker to use my ethernet connection via a Netgear Powerline Home Theatre Set-up to stream Trailers and Movies on the Apple TV, however this is no good when connecting directly to my Mac to stream music or TV shows in iTunes, so revert to the wifi connection that I created on my Time Capsule to do this.
    Would be handy if Apple TV had a menu option where you could manually change the connection type depending on what you were doing, as per above scenario.
    Cheers
    Brett

    brettfromseabrook wrote:
    Hi All
    Was wondering if there is an easy way to switch between ethernet and wifi connection on Apple TV without having to disconnect the ethernet cable.
    Unfortunately not.

  • Can i run a printer off the ethernet cable connection without hurting the imac or is the ethernet slot only for internet connection?

    can i run a printer off the ethernet cable connection without hurting the imac or is the ethernet slot only for internet connection?

    Hi, Alan -
    How can I connect to both printer (HP 4050n, via direct connection) and internet (via LAN), as my iMac has only one R45 port?
    You can, but you'll need to expand your cabling a bit.
    You'll need to get an intermediate ethernet hub, switch, or router. That device sits alone, with the Mac, your printer, and your modem/LAN plugged into it.
    If you are already using a router, either separate or in combination with the modem (many modems have a built-in router), then you just need a hub or switch.
    I use an ethernet switch (10/100/1000) to let both my Macs (a 2010 iMac and an elderly G4 DA model) use my HP4000n printer and my modem. The ethernet switch is a passive device, meaning there's no setup nor instructing it required - it's truly plug-and-play. All four items (two Macs, printer, and modem) are plugged into it via ethernet; both Macs have full-time independent access to the printer and the modem.

  • My PowerBook g4 says it's connected to the Internet and the Ethernet cable's plugged in, but every time I open Safari it says I'm not connected. What can I do to get Safari to get online?

    My PowerBook g4 says it's connected to the Internet and the Ethernet cable's plugged in, but every time I open Safari it says I'm not connected. What can I do to get Safari to get online?
    Also I'm having problems with my PowerBook G4 on recognizing my HP Photosmart C4680 All-In-One Printer/Scanner/Photocopier.   This is connect via USB printer cable, but yet they're not syncing. How can this be resolved?

    Internet Quick Assist:
    http://support.apple.com/kb/HT1144?viewlocale=en_US
    Troubleshooting internet settings:
    http://support.apple.com/kb/HT1714?viewlocale=en_US
    As for the printer problem, is this a new problem?
    Try an SMU reset:
    http://support.apple.com/kb/HT1939?viewlocale=en_US
    http://support.apple.com/kb/HT1436
    Then repair permissions and restart.

  • Can i unplug time capsule from the ethernet cable and still use it??

    can i unplug time capsule from the ethernet cable and still use it??

    I have tried to extend that wireless line but as soon as i remove the LAN cable i have no internet connection anymore. So basically, does the TC get the signal wireless from the router??
    The Time Capsule can wirelessly extend a wireless signal....but only if it is being provided by another Apple AirPort wireless router.
    If the "main" rotuer there is not an Apple AirPort router,  you will need to connect to the network using a wired Ethernet connection.

  • HT1338 After starting to download the Mountain Lion software, my wifi connection was disconnected. When I attached the ethernet cable, the downloading software was gone, and when I tried redoing the process, the app store would not accept the code. What d

    Hey,
    I just tried redeeming my software online. I went through the whole process, got the password, and proceeded to get the software to download. But soon after, the wifi connection was disconnected, and when I tried to connect the ethernet cable, the entire software had disappeared from my launchpad. When I tried to restart the download, it kept saying that the password had already been used before, and that it could only be used once per computer. What do I do now?

    You shouldn't have to re-enter the code, Lion should be on your purchases list so you can re-download it.  In the App Store, click Purchases...  do you see ML there?

  • Cant reinstall cs5 to my new macbook pro. the disk is keep ejecting out.

    Can't reinstall cs5 to my new macbook pro. the disk is keep ejecting out.

    Hi Hj yo,
    Please use the below link to download CS5 software.
    http://helpx.adobe.com/creative-suite/kb/cs5-product-downloads.html
    Thanks

  • I just bought an AirPort express. Currently I have a qwest wired router plugged into the back of my computer via an ethernet cable. Can I just unplug the ethernet cable and plug it into the AirPort express, then use the setup utility?

    I just bought an AirPort express. Currently I have a qwest wired router plugged into the back of my computer via an ethernet cable. Can I just unplug the ethernet cable and plug it into the AirPort express, then use the setup utility? Most of the discussions involve an existing wireless network. I don't have one.

    Correct. That's the way to set up the AirPort Express. After connecting your AirPort Express to the router, open AirPort Utility (in /Applications/Utilities) and follow the steps

  • How can I make Time Machine use the ethernet cable to Time Capsule instead of the wireless connection? Wireless is too slow; has been taking 40 hours to create an initial 142 GB backup.

    How can I make Time Machine use the ethernet cable to Time Capsule instead of the wireless connection? Wireless is too slow; has been taking 40 hours to create an initial 142 GB backup.

    Plug in ethernet .. in the computer.. turn off wireless.

Maybe you are looking for

  • What's wrong with iPhoto?

    Up until recently, when editing photos, the photo would black out when I try to edit. I have a Mac OS X Version 10.7.4 iphoto version 9.3 although continually updated. I am working with JPEGs and RAW photos and sometimes I am experiencing "technical

  • Background job not executing... pls help

    I want to schedule and execute a batch job with the start date and time with another program. In program1 im doing the below. job_open    getting job_count   CALL FUNCTION 'GET_PRINT_PARAMETERS'     EXPORTING       no_dialog              = abap_true

  • Will XML Help?

    I am loading a nice amount of data onto a server from a db so that clients can have quick access to the info (we wont have to go back to the db to get their info). As the data is growing I am getting an Out Of Memory error. Do you think that if I sto

  • CS3 license not valid

    I I am having the same problem! I've bought a new Mac and uninstalled CS$ from that system. Now on the new Mac, I keep getting Licence not Valid messages. I have tried enetringthe original lic from the CS3 design Premium and with the hope that I can

  • New Envy laptop, color seems off and very ugly

    Hello, I just got a new Envy 17t Touchscreen. The new style of it, that comes with the B&O Audio.  It is so beautiful. However the color is just beyond ugly. The computer takes on a brown hue across the whole screen. I've tried to find the RGB values