The event logging service encountered an error while processing an incoming event published from Microsoft-Windows-Security-Auditing.

Last night, some of our systems installed updates released on 11/13/2014.
KB3021674
KB2901983
KB3023266
KB3014029
KB3022777
KB3020388
KB890830
Today, all of the servers running Windows Server 2008 R2 started logging the following error in the Security log over and over:
Log Name:      Security
Source:        Microsoft-Windows-Eventlog
Date:          1/15/2015 11:12:39 AM
Event ID:      1108
Task Category: Event processing
Level:         Error
Keywords:      Audit Success
User:          N/A
Description:
The event logging service encountered an error while processing an incoming event published from Microsoft-Windows-Security-Auditing.
Servers running Windows Server 2008 that also installed the updates are not experiencing the problem. It looks like one of the updates may have introduced this problem with Server 2008 R2.

...Did you for sure confirm that:
https://technet.microsoft.com/library/security/MS15-001
is the cause?
I did. I had a VM that was not experiencing the problem. I took a snapshot and tested the patches one by one. Installing only KB3023266 immediately caused the issue to occur (after reboot). A similar process was used to confirm that
installing KB2675611 resolved the problem.
Note that I found the installation of KB2675611 is usually quick, but it took several hours hours to install on some of our systems. We had installed this patch a few months ago on a couple of servers and it was always quick to install. But,
it seems like installing it on a symptomatic system can cause it to take a long time.

Similar Messages

The event logging service encountered an error (res=5) ...

Hi,
I have promoted a new server to be a third DC.
All seems ok, replication, dns, etc are working properly but after the boot in the system event log I see those errors:
Log Name: System
Source: Microsoft-Windows-Eventlog
Date: 25.5.2012 14:32:15
Event ID: 23
Task Category: Service startup
Level: Error
Keywords: Service availability
User: LOCAL SERVICE
Computer: dc3.x.x
Description:
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-API-Tracing/Operational.
and then for about 40 Microsoft channels:
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-AppID/Operational.
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-AppLocker/EXE and DLL.
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-AppLocker/MSI and Script.
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-Audio/CaptureMonitor.
The event logging service encountered an error (res=5) while initializing logging resources for channel Microsoft-Windows-Security-Configuration-Wizard/Operational.
etc...
There is no error event before those event id 23
Any idea?
Thank you

Have you checked the path of the System event log? Something similar happened to me once, turned out the log file was corrupted. I updated the path and created a new evt which solved the issue for me.
Hopefully this helps:
http://technet.microsoft.com/en-us/library/dd315662(v=ws.10).aspx

Get-mailboxdatabasecopystatus -identity DBNAME | fl gives errors "The Microsoft Exchange Replication service encountered an error while attempting to start a replication instance for". DB is mounted and the DB copies are in healthy status.

We are getting a SCOM alert " Database copy isn''''t keeping up with the changes on the active database copy and has failed."
When we go to the mailbox server and check we found all the Mailbox DB's are mounted properly and their copies are in healthy state. Further digging to this problem we found that there are no critical events to this DB in the eventviewer.
When we runt he get-mailboxdatabasecopystatus -identity DBNAME | Fl then in the ErrorMessage section we get error "The Microsoft Exchange Replication service encountered an error while attempting to start a replication instance for . If the copy doesn't
recover automatically, administrator intervention may be necessary. Error: The directory is not empty."
ErrorEventID : 4126
In the event viewer we get a Information event 4114 saying the DB redundancy health check passed and in the details section we get the same error message mentioned above.
Also we observed that the "MSExchange Replication" counter "Failed" is set to 1 for this perticular DB but is is set to 0 for the other DB's. Tried restarting the MSEXChange replication service but still the "Failed" counter
is 1 and the SCOM alert is still active.
The version is Exchange 2010 SP3 UR5
Any clues???

Hi,
From your description, this issue only affect one mailbox datatabase.
Please use the Update-MailboxDatabaseCopy command to check result.
If it doesn't work, please dismount your active database copy and check if this is Clean Shutdown, if it's dirty shutdown, please bring to clean shutdown and mount this database copy. Then run the Update-MailboxDatabaseCopy command again to check result.
Best regards,
Belinda Ma
TechNet Community Support

Facetime: The server has encountered an error while processing the registration

I always used FaceTime normally this morning gives me this error after entering Apple ID credentials. I tried to edit the hosts file and delete the certificate but both solutions are not served. Can you help me?
thanks

can anyone help me? Please

I am receiving the following message "Sync encountered an error while connecting: Server incorrectly configured. Please try again." How can I resolve this?

Sync last worked successfully Friday 6/10/11 @ 13:46 just before I left work. Shut computer down. Monday, started computer, and tried to sync and received error. No changes have been made to system.
Win 7
Firefox 4.0.1
Extensions;
Adblock plus 1.3.8
Java console 6.0.24
Symantec IPS 2.0
How can I remedy this issue?

This hasn't fixed itself over here. Should I post a sync log or start a new thread?

I get error message when trying to use Firefox Sync after upgrate to 5.0. The message reads: "Sync encounted an error while syncing: Unknown error. Sync will automatically retry this action" I am using Windows 7.0 on a stationary computer.

Simply: Firefox Sync doesn't work after upgrade to 5.0.

You can have a try, unmark the Tabs in Sync of Preferences.

Error while generating PDF with BI Publisher from APEX

Hi,
I am facing a problem which is intermittent.
I am generating a pdf from APEX which has been developed using BI Publisher.
I have linked the report to the APEX using report queries/report layouts in shared components.
The pdf used to open without any problems previously.But currently,I am getting the following error
"An error exists on this page.Acrobat may not display the page correctly.Please contact the person who created the pdf document to correct the document."
Once the Bi Publisher Services is restarted,I am able to generate the pdf.Again After sometime the same error pops up.
Has anybody faced the above error?
Any solution for the same.
Kindly reply.
Thanks and Regards,
K Tanna

in the log file,following message was shown
[050510_021134100][oracle.apps.xdo.template.FOProcessor][STATEMENT] clearInputs(Object) is called.
[050510_021134126][oracle.apps.xdo.template.FOProcessor][STATEMENT] clearInputs(Object) done. All inputs are cleared.
[050510_021134126][oracle.apps.xdo.template.FOProcessor][STATEMENT] End Memory: max=15744MB, total=237MB, free=121MB

Firefox Sync encountered an error while syncing: Unknown error

I am trying to connect to the site - https://login.salesforce.com/?ec=302&startURL=%2F5003000000EIhFk and i just cannot login. the site is accessible, but could not log in and I have this error in the status area on the bottom - Firefox Sync encountered an error while syncing: Unknown error

I think I managed to fix this.
Go to [https://account.services.mozilla.com/ your sync account], log in, and click clear your sync data.
Then click the Sync now button on the error message.
The error went away for me.

Acrobat has encountered an error while playing this media clip

Hi,
I have downloaded a pdf file from the web which has embedded audio in it.
When I try to play the audio, the following message comes up “Acrobat has encountered an error while playing this media clip. Adobe’s Windows build-in player cannot play this format as the required decoder is not installed on the system.”.
I can attach the file, if the problem can be resolved. If you need more information, kindly advise?
Can you kindly assist?

That means it's a PDF containing "legacy media", which requires external software to play it. Unfortunately the audio itself could use any type of encoding, and the error tells you that whatever it is, your default media player (WMP) doesn't understand it. Rather annoyingly, when running in embedded mode WMP doesn't tell you what codec it's having problem with. It's one reason why this feature has been removed from the latest version of Acrobat.
This forum doesn't allow generic file attachments, but if the PDF came from a public website please post the URL and someone will take a look at the structure. Sharing of copyrighted material via file upload services is not permitted.

"sync encountered an error while syncing" (Firefox 4.0b12pre)

Fore weeks now, Firefox 4.0b12pre has not been able to sync. I get the following error message in the status-bar: "''Sync encountered an error while syncing: Unknown error. Sync will automatically retry this action" [Sync Now]''
I have the nightly build on 2 PCs (Windows 7 64-bit). I have tried "Reset Sync" with no success. All of my backup bookmarks are from after the problem manifested itself (so I didn't do a restore from backup).

There was a server out last week. see below. now everything works great. thanks for the follow up.
To:
Subject: [Bug 744289] sync107.db.scl3 down
Do not reply to this email. You can add comments to this bug at
https://bugzilla.mozilla.org/show_bug.cgi?id=744289
Gregory Szorc [:gps] <[email protected]> changed:
          What    |Removed                     |Added
            Status|UNCONFIRMED                 |RESOLVED
        Resolution|                            |FIXED
           Summary|error in sync               |sync107.db.scl3 down
     Last Resolved|                            |2012-04-10 19:39:11
--- Comment #2 from Gregory Szorc [:gps] <[email protected]> 2012-04-10
19:39:11 PDT --- Well, this is embarrassing. It looks like one of our
servers was down and for whatever reason we didn't notice.
It should be working now. If you still see errors, please reopen this bug.
Configure bugmail: https://bugzilla.mozilla.org/userprefs.cgi?tab=email
------- You are receiving this mail because: ------- You reported the bug.

Error while processing the dimension

Multiple Specification of the Name 'HIR' as a Component Name (Component 6)
this is the error i am geting while processing the dimension

Hi,
Do you get this error while processing all the dimension or only in specific dimension?
Do you have hierarchies in this dimension? Have you added the hierarchy in the property (you should not).

Error Event ID 11 The KDC encountered duplicate names while processing a Kerberos authentication request.

I've been noticing The Error with event ID 11 popping up a lot on our domain controllers:
The KDC encountered duplicate names while processing a Kerberos authentication request.
When running setspn -X it says that it found 111 groups of duplicate SPNs. However, when going through the list, it references domain service accounts that are used to run our SQL Server services. We have about 50 remote locations and each of them has 3
machines participating in a SQL mirror (principal, mirror, witness) and they all run the SQL Server service on the same account (1 account per location).
We haven't experienced any issues at all but I was wondering if this could cause problems or if we are straying from best practice. Any advice is welcome. Thanks!

I believe what you should do to follow best practice is to provide unique SPNs for each SQL server, which will also provide increased security, and to do that you must create individual service account for each SQL server so it can associate that
account with that server's SPN.
Here's more on it to help guide you. Read Paul's comments, as well as other suggestions in the following thread:
event ID 11 There are multiple accounts with name MSSQLSvc/xxxxxx
http://social.technet.microsoft.com/Forums/windowsserver/en-US/8df35316-23ba-48ba-aa3e-2249fcbfecbc/event-id-11-there-are-multiple-accounts-with-name-mssqlsvcxxxxxx?forum=winserverDS
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights.

The test encountered an error while signing in to Outlook Web App. HTTP code: 200

Infrastructure: Exchange 2010 SP3 RU2 environment on 17 servers worldwide with CAS, MB, HUB and UM roles. Server 2008 R2 VM's on Hyper-V 2008 R2.
Trying to run the following command to test OWA connectivity on a server in the same Active Directory domain but in a different AD site:
Get-ClientAccessServer -Identity Server1 | test-owaconnectivity -AllowUnsecureAccess -TrustAnySSLCertificate
I get the reponse:
WARNING: [11:04:51.276] : An Outlook Web App page wasn't received.
WARNING: [11:04:51.276] : The test encountered an error while signing in to Outlook Web App.
HTTP code: 200
WARNING: [11:04:51.276] : Test failed for URL 'https://server1.domain.com/owa/'.
ClientAccessServer        MailboxServer            URL
Scenario       Result       Latency          Error
Server1.domain.com      Server2.domain.com  https://server1.domain.com/owa  Logon           Failure
The test encountered an error while signing in to Outlook Web App. HTTP code: 200
This is the same error message received from SCOM on its tests also.
I have created a test account on all 17 servers using ./new-TestCasConnectivityUser and ensured their mailboxes reside on the correct server in the correct database.
All internal servers are set for OWA and ECP for Windows Authentication. Only public facing CAS servers are set to Forms based. That said, have checked the 'Microsoft Exchange Forms-Based Authentication service' is running on both Server1 and Server2 as
are all Exchange services except 'Microsoft Exchange IMAP4' (not used) or 'Microsoft Exchange POP3' (not used).
However, if I run this command:
test-owaconnectivity -AllowUnsecureAccess -TrustAnySSLCertificate -URL
https://server1.domain.com/owa
I get the following success after I have entered my correct credentials:
Windows PowerShell Credential Request : cmdlet Test-OwaConnectivity at command pipeline position 1
Warning: This credential is being requested by a script or application on the Server2.domain.com remote computer.
Enter your credentials only if you trust the remote computer and the application or script requesting it.
Supply values for the following parameters:
MailboxCredential
ClientAccessServer MailboxServer URL
Scenario              Result      Latency    Error
(ms)
                                                        https://server1.domain.com/owa
Logon                 Success    6282.13
So if I login with my domain username, it works and logs in. If the script runs using the 'extest....' user account created by the above ./new-TestCasConnectivityUser.ps1 , it does not work.
Has anyone got any ideas please? I know its not the network as it works under my username, I know all fo the services required are running as it works under my username. There are no entries at all in the receiving server's error logs for Application, System,
Exchange or Powershell at all.
Any help greatly appreciated.
Danny

Did you read this? http://support.microsoft.com/kb/2277649/en-us
Did you run Test-MapiConnectivity? If not, can you run and post results?
HossFly, Exchange Administrator

Trying to setup new iCloud in system preferences and get error message: "iCloud encountered an error while trying to connect to the server."

Here's the sequence of events:
Setting up a new iMac.
Migration Assistant was aborted during setup and a normal setup was completed.
Then ran Migration Assistant from the newly setup account.
It ran fine, but put all the data in a new account called "user".
Renamed "user" to a new name, renamed the home folder to a new name following these instructions: OS X: How to change your account name or home directory name
Delete the account we originally created, so just have one account with the name we want and all the data, email. Works fine.
Sign into the App Store with the account we share for purchases.
Now, the problem:
Go to System Preferences to setup iCloud with a new Apple ID
Get this error: "iCloud encountered an error while trying to connect to the server."
So I'm unable to setup iCloud for photo stream, FaceTime, etc.
Internet works fine, we can get mail, etc.
Rebooting doesn't help
Ideas?

never mind the problem is gone this morning.

Evdre encountered an error while retrieving the data

hi
all
i have an error
"evdre encountered an error while retrieving data" evdre addin
evdre cannot retrieve data
working on ms 7.0 bpc
excel 2003
i have gone thru the sap service place and found that i have to replace 2003 to 2007
please let me know also if there is any possibility to change my reports in such a way that i may pass with out this error
what is the mistake i am doing while i create the reports ?
ur help is appreciated
thanks

This error message has many root cause.
First let's check if the installation of BPC client is correct.
Just use a simple EVDRE functions and try to expand.
Are you receiving any error? If yes then I suggest to try also for Apshell ppset.
If it is not working then that's means you have a problem with installation.
If you can use EVDRE from another machine then the problem is installaytion of the client.
If the problem is into all computers then the problem is into server.
If the problem is just into one report then you have to review that report because some parameters sent to EVDRE are wrong otit is trying to retrievea region which is toobig.
I hope this will help you toinvestigate the issue.
Regards
Sorin Radulescu

The event logging service encountered an error while processing an incoming event published from Microsoft-Windows-Security-Auditing.

Similar Messages

Maybe you are looking for