"The file is possibly corrupt. The file header checksum does not match the computed checksum."

Yesterday evening, I accidentally dropped my Probook 6565b. It bluescreened with strange red boxes around the text, so I thought the screen or something was damaged. I emergency shut down the computer, and started it up again. It was visibly slower, but I was able to use it, so, relieved, I turned it off again and went to bed.
This morning, I tried to turn it on again. It started out normally (and I am able to access the start up screen) . But afterwards, it gives me a blank dark blue screen (like before you see the Windows logo) and it stays there for around 15 seconds before it gives me the error.
I have no idea what to do, so any advice would be greatly appreciated!
I think my operating system is Windows 7, but I'm not sure.
Thank you.

I see you have damaged both your hardrive(hardware) and your operating sytem (corrupted too, software)
You may want to run an diagonstic test of your hard drive complete before trying to reinstall windows.
Press ESC right after power button and repeatdley and look for Diagnostic test and start up test and hard drive test.
Please report results.
Sorry because of different timezone I might not be able to help/reply you right away.IF that happens I deeply apologize!
**Click the White thumb if you like the answer.**
**Please mark Accept As Solution if it solves your problem and only solves your problem, if you have any more questions please ask, this also helps others to solve related issues.**
Feel yourself like home here, we are all happy to help, if you have an question reply or start a topic or pm me or an expert.

Similar Messages

The file may be corrupt. The file header checksum does not match the computed checksum.

I just put Vista Home Premium on a computer I was going to give to my son. Upon adding some hardware I kept getting the above screen. "The file may be corrupt. The file header checksum does not match the computed checksum.' When I booted in safe mode and slow boot, it hung on crcdisk.sys. I removed everything except the keyboard hhd dvd and fdd and it still does the same thing. I tried to reinstall Vista but it keeps hanging. From reading a lot of other threads this seems to be a big problem. I doubt if the product should have been marketed. But.... If anyone can help me get it booted I would like to try XP instead. I tried to install XP on the same drive and it hungs there too.

Hi ballen6721,
Thank you for the post.
This issue can occur if the newly installed hardware device is incompatible with the system.
Based on the current situation, I suggest trying the following steps to troubleshoot the issue:
Method 1 Device Clean Boot
============================================
Please unplug all unnecessary devices such as sound card, printer, network card and TV card.
Method 2: Startup Repair from the Windows Recovery Environment (WinRE)
============================================
1. Insert the Windows Vista installation disc into the disc drive, and then start the computer.
2. Press a key when the message indicating "Press any key to boot from CD or DVD …". appears.
3. Select a language, a time and currency, and a keyboard or input method, and then click Next.
4. Click Repair your computer.
5. In the System Recovery Options dialog box, choose the drive of your Windows installation and click Next.
6. At the System Recovery Options Dialog Box, click on Repair your computer.
7. Click the operating system that you want to repair, and then click Next.
8. In the System Recovery Options dialog box, click Startup Repair.
Method 3: Use the Windows Recovery Environment (WinRE) to run System Restore ============================================
1. Insert the Windows Vista installation disc into the disc drive, and then start the computer.
2. Press a key when the message indicating "Press any key to boot from CD or DVD …". appears.
3. Select a language, a time and currency, and a keyboard or input method, and then click Next.
4. Click Repair your computer.
5. In the System Recovery Options dialog box, choose the drive of your Windows installation and click Next
6. At the System Recovery Options Dialog Box, click on System Restore.
7. Follow the System Restore Wizard instruction and choose the appropriate restore point.
8. Click Finish to restore the system.
Note: If you computer is an OEM one, the method to enter WinRE can be different, you may contact your OEM to consult how to enter WinRE.
Can we start the computer now?
If the issue persists, please help confirm the following points:
1. What hardware changes have you made recently?
2. Can we enter Safe Mode now?
I look forward to hearing from you.
Best regards,
Tim Quan
Microsoft Online Community Support

"the file header checksum does not match the computer checksum." Pavilion P6000

HP Pavilion P6000
Windows 7 64-bit
The file is possible corrupt. The file header checksum does not match the computer checksum
I was previously getting blue screens saying things like "Memory_Management"

I see you have damaged both your hardrive(hardware) and your operating sytem (corrupted too, software)
You may want to run an diagonstic test of your hard drive complete before trying to reinstall windows.
Press ESC right after power button and repeatdley and look for Diagnostic test and start up test and hard drive test.
Please report results.
Sorry because of different timezone I might not be able to help/reply you right away.IF that happens I deeply apologize!
**Click the White thumb if you like the answer.**
**Please mark Accept As Solution if it solves your problem and only solves your problem, if you have any more questions please ask, this also helps others to solve related issues.**
Feel yourself like home here, we are all happy to help, if you have an question reply or start a topic or pm me or an expert.

Selected file cannot be linked because its type (video) does not match the original file's type

I've been using Premiere Elements 9 for a couple of years now, and a few months ago I began having problems importing AVI files created from a BlackMagic Intensity Pro capture card. (These issues were not previously occurring, and since they surfaced, I have exhausted the various settings for the BlackMagic card, used various software such as BlackMagic's own Media Express as well as the freeware VirtualDub, and still have the following problems.)
In addition, these AVI files play just fine, in their entirety, using Windows Media Player and in Quicktime.
The problem (or possibly two, but I suspect they could be related) is that most of the AVI files I attempt to import will either (1) import all video and NO audio, or (2) import ONLY a short segment of audio and video, and the length that Elements imports varies. Usually only in the range of a minute or two. The rest of the file is not imported at all.
After much digging in forums, and testing various settings in trying to figure out the issue, I decided to back up all of my files and completely wipe all hard drives and start over with a fresh installation of Windows and Premiere Elements 9. I haven't installed much else yet, as I wanted to first find out if the reinstallation improved things with Elements.
For the first project I created in Elements after the reinstallation, Elements successfully imported an entire AVI that was nearly 2 hours long, audio and video. This was a file that previously would not import properly into Elements. This suggested that my earlier installation of Elements must have been corrupted somehow. At this point I was very hopeful that all was well.
I proceeded to edit the video as I had wanted, saved the project, and exported it to an MPEG format file. I had originally wanted to export it as an MOV, but I hadn't yet installed Quicktime, so Elements couldn't do that just yet. The MPEG export was successful and plays fine.
However, I then installed Quicktime, and once it was finished, I restarted the PC and reloaded the same project. This time, Elements claimed the media was offline. I double-clicked on a segment of the video, and directed Elements to the raw file, but then an error message popped up: "The selected file cannot be linked because its type (video) does not match the original file's type (audio and video)." This was the same file I had JUST edited and of which I created an MPEG.
I tried creating a new project and the "Get Media" function to import the AVI again, but this time only the video imported with NO audio. (This would explain why the error message said what it did, but not why the audio wasn't imported.)
What in the world is going on with Elements??? I am baffled since the ONLY task I have done on this machine after a complete reinstallation of both Windows and Elements is edit one AVI. I find it very hard to believe that just installing Quicktime caused this.
Some info on my system:
System: Asus P6T w/ Intel i7 920 and 12 GB memory
OS: Windows 7 Ultimate
Video Software: Premiere Elements 9
Capture Card: BlackMagic Intensity Pro (PCI-e)
Capture Software: AVIs recorded with either BlackMagic Media Express or VirtualDub (only prior to the reinstallation, as neither of these programs are currently installed)
I'm getting to the point with Elements that I might need to just abandon it and find something else that is more reliable. Anybody have suggestions to help with this, so I won't have to migrate?

mtnsports
We think that we need to start off with definiting the properties of these .avi files that you are importing into Premiere Elements 9.0/9.0.1 (assumed that you are working for the required 9.0.1 Update).
You say that the "avi" was created from a "BlackMagic Intensity Pro capture card". What are the properties of this .avi that you imported into Premiere Elements? Not all .avi are created equal. What is the video and audio compression, frame size, frame rate, interlaced or progressive, pixel aspect ratio, typical duration?
Based on the properties of the video what have you been setting as the project preset?
Let us start here.
More later.
ATR

CS5 The selected file cannot be linked because its type (audio) does not match the original file's t

Greetings,
I have been working on a very large project using CS5 on my desktop computer. Now I am on the road and bought a laptop so that I can continue to work. I placed all of my assets on a back-up external 2tb drive (which I was able to open without incident on my desktop). I installed CS5 on my new laptop and now when I try to open the project I get the following message "The selected file cannot be linked because its type (audio) does not match the original file's type (audio and video)". This message appears before I indicate the path to any of the assets. Then, when I do indicate the path to each asset, I get the same message for individual files.
Any advice is appreciated.
Thanks,
Jeremy

I had this problem and have found a solution / workaround: my issue was when trying to open a cs5 project that had been collected on mac and then transfered to pc, my footage was all png image sequences but this will hopefully work in other situations...
Open the project and cancel the first dialogue box that pops up where you get the "file cannot be linked" error when trying to reconnect footage. The project will open and then in the project panel, right click on any footage that needs reconnected and choose "Replace footage..." this will open a dialog that will allow you to select the file that gave you the error in the first place without any issues. Any sequences with that footage will now work and everything show be all good.
You may experience "Offline material is present in this export and will be encoded using the offline media graphic" on first export but apparently you can just ingore that, but i guess it's woth testing a few short sections before commiting to a huge render...
This workaround isn't perfect as i had about 50 pieces of footage i had to relink via this method one by one but at least it saved redoing the edit which was critical for my project...
good luck!

The located assembly's manifest definition with name 'openfoundation' does not match the assembly re

Ok. been working on this for the better part of a day. I am having trouble with the .net web controls. trying to create a simple portlet that populates a text box with values from a 2nd text box when a button is selected. both text boxes are in the same portlet.
without using the <httpModules> entry in the web.config file the portlet works fine, but it does pop you out of the portal.
setup: working in a Dev. environment with portal and portlets on the same box.Portal version is 5.0.2.EDK version is 5.0.2.
error:
The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Source Error:An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.Assembly Load Trace:The following information can be helpful to determine why the assembly 'openfoundation' could not be loaded.=== Pre-bind state information ===
LOG: DisplayName = openfoundation, Version=2.0.9.3152, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
(Fully-specified)
LOG: Appbase = file:///c:/inetpub/wwwroot/netTest
LOG: Initial PrivatePath = bin
Calling assembly : dotnetportlet, Version=3.5.0.1, Culture=neutral, PublicKeyToken=null.
===
LOG: Publisher policy file is not found.
LOG: No redirect found in host configuration file (C:\WINNT\Microsoft.NET\Framework\v1.1.4322\aspnet.config).
LOG: Using machine configuration file from C:\WINNT\Microsoft.NET\Framework\v1.1.4322\config\machine.config.
LOG: Post-policy reference: openfoundation, Version=2.0.9.3152, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/nettest/9e6689f5/a0d2f067/openfoundation.DLL.
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/nettest/9e6689f5/a0d2f067/openfoundation/openfoundation.DLL.
LOG: Attempting download of new URL file:///c:/inetpub/wwwroot/netTest/bin/openfoundation.DLL.
WRN: Comparing the assembly name resulted in the mismatch: Minor Version
Stack Trace:[FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.]
   Plumtree.Remote.Portlet.PortletContextFactory.CreatePortletContext(HttpRequest req, HttpResponse resp) +0
   Com.Plumtree.Remote.Transformer.Condition.GatewayedStandardCondition.UseFilter(HttpContext ctx)
   Com.Plumtree.Remote.Transformer.FilterManager.UpdateFilter(HttpContext ctx)
   Com.Plumtree.Remote.Transformer.PTTransformer.BeginRequestHandler(Object sender, EventArgs e)
   System.Web.SyncEventExecutionStep.System.Web.HttpApplication+IExecutionStep.Execute() +60
   System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +87
Version Information: Microsoft .NET Framework Version:1.1.4322.573; ASP.NET Version:1.1.4322.947
************************************************************Is there any step by step instructions for setting up and using the .net web controls in Plumtree????
There doesn't seem to be any information in one spot as to setting up the environment to use the .Net Web Controls. I have had to piece together information from multipule threads to get this far. I.E. there was nothing in any documentation that I have read that required the installation of the VJ# lib's. (that error took me the first half of the day to resolve :-) )
Thanks for any help,
Greg************************************************************

Also, when reviewing the Plumtree_.NET_Web_Controls_InstallLog.log there were 5 nonfatal erros. These error's were:
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\edk.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\edk.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\jsregistry.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\jsregistry.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\log4net.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\log4net.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\openfoundation.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\openfoundation.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\Plumtree.WCFilter.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\Plumtree.WCFilter.dll (The process cannot access the file because it is being used by another process)
When installing the Web Control's do you need to stop any services? I didn't see anything in the install notes about doing this?

Pretzel: The located assembly's manifest definition with name 'openfoundation' does not match the

We have got 5.0.2 Plumtree portal, EDK 5.0.2 and .Net Web Controls 2.1.
I am trying to call:
IPortletContext oPortletContext = PortletContextFactory.CreatePortletContext(System.Web.HttpContext.Current.Request, System.Web.HttpContext.Current.Response);
I have attached the error I am getting. Is this related to Open Foundation version? This is quite urgent because we are in the process of trying to get a demo together for grabbing Activity Rights.
Server Error in '/portlets/DOJ/JNET/pretzel.clients.doj.reentry' Application.
The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Source Error:An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.Assembly Load Trace:The following information can be helpful to determine why the assembly 'openfoundation' could not be loaded.=== Pre-bind state information ===
LOG: DisplayName = openfoundation, Version=2.0.9.8318, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
(Fully-specified)
LOG: Appbase = file:///E:/Data/HSTPRDAPP01/Inetpub/plumtree/portlets/DOJ/JNET/pretzel.clients.doj.reentry
LOG: Initial PrivatePath = bin
Calling assembly : dotnetportlet, Version=3.5.0.1, Culture=neutral, PublicKeyToken=null.
===
LOG: Publisher policy file is not found.
LOG: No redirect found in host configuration file (C:\WINNT\Microsoft.NET\Framework\v1.1.4322\aspnet.config).
LOG: Using machine configuration file from C:\WINNT\Microsoft.NET\Framework\v1.1.4322\config\machine.config.
LOG: Post-policy reference: openfoundation, Version=2.0.9.8318, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/portlets_doj_jnet_pretzel.clients.doj.reentry/26128f6f/cfc1837a/openfoundation.DLL.
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/portlets_doj_jnet_pretzel.clients.doj.reentry/26128f6f/cfc1837a/openfoundation/openfoundation.DLL.
LOG: Attempting download of new URL file:///E:/Data/HSTPRDAPP01/Inetpub/plumtree/portlets/DOJ/JNET/pretzel.clients.doj.reentry/bin/openfoundation.DLL.
WRN: Comparing the assembly name resulted in the mismatch: Minor Version
Stack Trace:[FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.]
   Plumtree.Remote.Portlet.PortletContextFactory.CreatePortletContext(HttpRequest req, HttpResponse resp) +0
   pretzel.clients.doj.reentry.navigation.Page_Load(Object sender, EventArgs e) in \\devnet2\inetpub\doj\reentry\development\pretzel.clients.doj.reentry\navigation.aspx.cs:22
   System.Web.UI.Control.OnLoad(EventArgs e) +67
   System.Web.UI.Control.LoadRecursive() +35
   System.Web.UI.Page.ProcessRequestMain() +750
Version Information: Microsoft .NET Framework Version:1.1.4322.1031; ASP.NET Version:1.1.4322.947

I have seen this before after a upgrade of the EDK, found I had to remove the reference in the C# project to the old EDK dll and re add it to the new EDK dll.
Also noticed that you are using the System.Web.HttpContext.Current fully qualified namespace in the CreatePortletContext() call instead of the usual way of PortletContextFactory.CreatePortletContext(Request, Response) this uses the System.Web.HttpRequest.Page namespace by default.

AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'

Hi,
There are three different types of APs associated with controller and working fine.
1.       AIR-LAP1252AG-E-K9
2.       AIR-LAP1522AG-E-K9
3.       AIR-CAP1552E-C-K9
WLC is AIR-CT5508-K9. Software version is 7.4.100.0. Field Recovery Image is 7.0.112.21. Firmware version is FPGA 1.7, Env 1.8, USB console 2.2. WCS is 7.0.240.0 for Windows.
WCS is sending alarms for AIR-LAP1522AG-E-K9:
Message: AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'.
Before Controller was 7.2.4 (not sure).
Country configured on WLC is AE and shows -CE regulatory domain. Mesh APs are also associated.
I believe this Critical alarm should not come.
how much is this alarm important? What should be done to resolve this?

Typically you still need to make sure that the country codes are indeed configured on the WLC. Thing can change when you upgrade code as standards might of changed and regulations also. If your AP's are functional, then you should be okay and I wouldn't worry too much about it, but if after the upgrade, the WLC complains about country code stuff, then you just need to verify that the AP's country code is defined on the WLC. May times the AP will not join and if it does join, the radios might be disabled or in a down status.
Sent from Cisco Technical Support iPad App

CS6 The selected file cannot be linked because its type (audio) does not match the original file's t

I understand there is another posting in this forum with the same error happening on CS5 and their solution had something to do with Quicktime. Mine has nothing to do with this.
I ran into this exact same problem in CS6 and I found that the issue is because I renamed the root project folder. My folder structure is like this:
Drive C:\
-> [root project folder]
-> [folder containing videos]
-> MyProject.prproj
By renaming the root project folder, I was no longer able to open up the project successfully. It would get to certain clips and ask about where the clip was located. Trying to re-link it to the correct file would result in that error (which makes no sense if you think about it).
So my question is, is it intentional that the absolute folder paths are saved into the project file rather than relative paths? Does it not make more sense if paths were saved relative to the root project path? That way the root project folder could be renamed to whatever you want and it would have no effect on the project itself.

I had this problem and have found a solution / workaround: my issue was when trying to open a cs5 project that had been collected on mac and then transfered to pc, my footage was all png image sequences but this will hopefully work in other situations...
Open the project and cancel the first dialogue box that pops up where you get the "file cannot be linked" error when trying to reconnect footage. The project will open and then in the project panel, right click on any footage that needs reconnected and choose "Replace footage..." this will open a dialog that will allow you to select the file that gave you the error in the first place without any issues. Any sequences with that footage will now work and everything show be all good.
You may experience "Offline material is present in this export and will be encoded using the offline media graphic" on first export but apparently you can just ingore that, but i guess it's woth testing a few short sections before commiting to a huge render...
This workaround isn't perfect as i had about 50 pieces of footage i had to relink via this method one by one but at least it saved redoing the edit which was critical for my project...
good luck!

Need help urgently!! - "The selected file cannot be linked because its type (video) does not match t

Hey guys... I need your help!! I started a project using Premiere Pro 2 and was 80% when I formatted my computer (all my project files were always saved to a external hard drive). Anyways instead of installing Premiere Pro 2, I installed Premiere Pro Cs3. Problem is whenever I try starting up my project it asks me to link every file used. When I do this it says "The selected file cannot be linked because its type (video) does not match the original file's type (audio and video)." I took my external harddrive to friend's house who has Premiere Pro 2 and it says the same thing. Why did this happen? Is there anyway around it... Any help would be greatly appreciated, I put over 20 hours into editing this movie... I don't want it all to go to waste.

Frequently answered question
Cheers
Eddie
Forum FAQ
Premiere Pro Wiki
- Over 250 frequently answered questions
- Over 100 free tutorials
- Maintained by editors like
you

There is a problem with the proxy server's security certificate. The name on the security certificate is invalid or does not match the name of the target site "Mailserver"

Good day Guys
First of all I am not an Exchange Expert, and I might be asking a very stupid question, but please bare with me. :)
While I was on leave our Mail server fell over and The company got a Specialist to help out for the time being.
We where\are on Microsoft Exchange 2007 , which Fell over, and the specialist was able to recover as much data as he could.
They then installed Exchange 2013 and tried to migrate everything from 2007 to 2013 and not everything migrated over.
But the problem is, Outlook Anywhere was enable on 2007 and worked a 100% (before the disaster)
With Exchange 2013 I get the following error message when trying to connect With Outlook 2013, using an external connection:
"There is a problem with the proxy server's security certificate. The name on the security certificate is invalid or does not match the name of the target site "Mailserver"
Outlook is unable to connect to the Proxy server. (Error Code 0)"
Has anyone had the Similar when migrating over from 2007 to 2013 or is this an Issue on IIS and nothing to do with Exchange migration?
Your assistance will be greatly appreciated.

Hi,
Firstly, I would suggest we use Exchange 2013 FE as the Outlook Anywhere proxy server.
For the certificate issue, it mostly occurs because the host name that Outlook are trying to access does not match the certificate SAN. Please check with this point. If they do not match, you
can change the host name by referring to the following article:
https://support.microsoft.com/kb/940726/en-us?wa=wsignin1.0
Thanks,
Simon Wu
TechNet Community Support

JNI generated header file does not match the class file

We have had a JNI project for many years and all has been fine. Within our libraries we have several classes that have inner enum classes.
Recently we have moved to JDK1.7. Up to now when JNI generated the methods where the signature used the inner enum class, and it was an oveloaded method, we would get something like the following as the signature:
Java_PackageName_ClassName_methodName_OuterClass_00024InnerEnum_2
And the class file result of the build would look like the following:
methodName(OuterClass$InnerEnum)
Since we have moved to JDK 1.7 the header file looks like the following:
Java_PackageName_ClassName_methodName_OuterClasss_InnerEnum_2
The class file is still the same, and because of that when we run the program we get an UnsatisfiedLinkError. I understand that this error is because the VM cannot find the implementation. So why JDK 1.7 generates a header file that does not match the class file?
Thank you in advance.

I don't have 1.6 to verify but your statements about what is generated for 1.7 for the header appear correct.
The 000024 represents the '$' and for 1.7 the inner class is still named using '$'. So for example after compiling in 1.7 the inner class file is named the following...
MyClass$InnerEnum.class
So a one to one conversion should have kept the 000024 (presuming it does in fact do it that way in 1.6.)
You might want to look at the release notes for 1.7.
If you need a solution you could add a post javah step that renames the file.

MacBook pro will not boot up. Blank screen with message File is possibly corrupted. Checksum does not match etc

MacBook Pro suddenly will not boot up. Blank screen with message File is possibly corrupt. Header checksum does not match, etc

Hi s.cheslik,
It seems your MacBook Pro will not boot properly and it displaying an error message. Based on the information you have provided, it appears your MacBook Pro needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
Apple - Support - Service Answer Center
Thank you for contributing to Apple Support Communities.
Take care,
Bobby_D

Could not load file or assembly 'log4net, Version=1.2.10.0, Culture=neutral, PublicKeyToken=692fbea5521e1304' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040

Please assist I am on a Windows 7 64 bit machine I have VS 2010 and have been fighting with this new program that I was brought on to help with - Issue is that I am unable to get rid of this issue. There is so many solutions but none have worked. If someone can give me some help with what has worked for you.
The error is Could not load file or assembly 'log4net, Version=1.2.10.0, Culture=neutral, PublicKeyToken=692fbea5521e1304' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)
This is with CR installed on 64 bit.
Thank you very much for any assistance with this problem,
Kris

Hi Vittorio
Please enter the search string 'log4net crystal net' into the search box in the top right corner. When the results come up, click on the Support Notes link. That will filter for the KBAs that you want to have a look at.
- Ludek
Senior Support Engineer AGS Product Support, Global Support Center Canada
Follow us on Twitter

Could not load file or assembly 'Microsoft.ReportingServices.SharePoint.ObjectModel' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)

Could not load file or assembly 'Microsoft.ReportingServices.SharePoint.ObjectModel' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)
===========================================================
This is a SQL Server 2012 Developer Edition of SSRS.
I am getting this error when navigating to http://servername/Reports. The reports site was working fine, until I installed a SQL 2014 Developer instance (including SSRS) on the same server.
I can still get to the http://servername/ReportServer site.
Neither of these are using Sharepoint.
Any help resolving this issue would be greatly appreciated.
Below is the stack trace.
===========================================================
[FileLoadException: Could not load file or assembly 'Microsoft.ReportingServices.SharePoint.ObjectModel' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)] System.Reflection.Assembly._nLoad(AssemblyName
fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) +0 System.Reflection.Assembly.InternalLoad(AssemblyName assemblyRef, Evidence assemblySecurity,
StackCrawlMark& stackMark, Boolean forIntrospection) +416 System.Reflection.Assembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) +166 System.Reflection.Assembly.Load(String
assemblyString) +35 System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +190 [ConfigurationErrorsException: Could not load file or assembly 'Microsoft.ReportingServices.SharePoint.ObjectModel'
or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)] System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +1149
System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() +323 System.Web.Configuration.CompilationSection.LoadAssembly(AssemblyInfo ai) +116 System.Web.Configuration.AssemblyInfo.get_AssemblyInternal() +36 System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection
compConfig) +212 System.Web.Compilation.WebDirectoryBatchCompiler..ctor(VirtualDirectory vdir) +174 System.Web.Compilation.BuildManager.BatchCompileWebDirectoryInternal(VirtualDirectory vdir, Boolean ignoreErrors) +57 System.Web.Compilation.BuildManager.CompileWebFile(VirtualPath
virtualPath) +295 System.Web.Compilation.BuildManager.GetVPathBuildResultInternal(VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +482 System.Web.Compilation.BuildManager.GetVPathBuildResultWithNoAssert(HttpContext
context, VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +108 System.Web.Compilation.BuildManager.GetVirtualPathObjectFactory(VirtualPath virtualPath, HttpContext context, Boolean allowCrossApp, Boolean
noAssert) +171 System.Web.Compilation.BuildManager.CreateInstanceFromVirtualPath(VirtualPath virtualPath, Type requiredBaseType, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +52 System.Web.UI.PageHandlerFactory.GetHandlerHelper(HttpContext
context, String requestType, VirtualPath virtualPath, String physicalPath) +53 System.Web.HttpApplication.MapHttpHandler(HttpContext context, String requestType, VirtualPath path, String pathTranslated, Boolean useAppConfig) +519 System.Web.MapHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
+176 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +274
===========================================================

Hi Glen，
"The located assembly's manifest definition does not match the assembly reference." is generally caused by the loaded assembly's version is different than the expected version application refers to.
In this case, it should be caused by:
While starting Report Manager, the backend process ReportingServiceService need to load assemblies it refers to
ReportingServiceService reads the compilation/assemblies element from web.config(under Report Manager virtual patch)
If the compilation/assemblies is not existing, ReportingServiceService loads all assemblies from Bin folder. It can be verified from call stack System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory(). ReportingServiceService
uses System.Reflection.Assembly.Load with the assemblies' name only to load assemblies.
The Assembly.Load tries to load from the specify assembly by name from GAC at first. If it is found from GAC, it won't be loaded from Bin folder any more.
Since Reporting Service SharePoint Integration mode is installed, a same assembly of 'Microsoft.ReportingServices.SharePoint.ObjectModel' with different version might be installed to the GAC. That causes the error "The located assembly's manifest definition
does not match the assembly reference."
For more information about the error message and the loading process, please see:
http://blogs.msdn.com/b/junfeng/archive/2004/03/25/95826.aspx
https://msdn.microsoft.com/en-us/library/yx7xezcf(v=vs.100).aspx
Thanks,
Jinchun Chen

"The file is possibly corrupt. The file header checksum does not match the computed checksum."

Similar Messages

Maybe you are looking for